Wyszukiwarka
Wydział Inżynierii Mechanicznej i Okrętownictwa
Publikacje
Filtry
wszystkich: 4536
wyświetlamy 1000 najlepszych wyników Pomoc
Katalog Publikacji
Rok 2022
-
Microcrystalline diamond film evaluation by spectroscopic optical coherence tomography
PublikacjaThis study has focused on the microcrystalline diamond film (MCD) thickness evaluation. For this purpose, optical coherence tomography (OCT) enhanced by spectroscopic analysis has been used as a method of choice. The average thickness of the tested layer was about 1.5 µm, which is below the standard 2-point OCT resolution. In this case, the usefulness of the spectroscopic analysis was confirmed for the evaluation of the thickness...
-
Modelling and Analysis of the Positioning Accuracy in the Loading Systems of Mobile Cranes
PublikacjaIn this work, the authors analyse the influence of the order and range of sequential movements of a crane's working members on the accuracy of the final cargo positioning. The analysis was conducted on the basis of a specially developed method in which the authors proposed the introduction of a geometrical indicator of positioning the load in the intermediate positions (after completing each movement sequence) and in the target...
-
Modelowanie wymiany ciepła przy wrzeniu w przepływie w warunkach podwyższonego ciśnienia zredukowanego dla R1233zd(E) jako potencjalnego czynnika w układach ORC [w:] Postępy w badaniach wymiany ciepła i masy
PublikacjaProces wrzenia w wysokotemperaturowych pompach ciepła oraz układach ORC zachodzi przy temperaturach wyższych niż 80˚C. W literaturze występuje luka w wiedzy dla podwyższonych temperatur nasycenia oraz korespondujących wysokich ciśnień zredukowanych. Większość istniejących danych doświadczalnych dotyczy temperatur niższych niż 40 ˚C, co związane jest z zastosowaniami chłodniczymi czynników niskowrzących. Dla temperatur wyższych...
-
Monitoring the gas turbine start-up phase on the platform using a hierarchical model based on Multi-Layer Perceptron networks
PublikacjaVery often, the operation of diagnostic systems is related to the evaluation of process functionality, where the diagnostics is carried out using reference models prepared on the basis of the process description in the nominal state. The main goal of the work is to develop a hierarchical gas turbine reference model for the estimation of start-up parameters based on multi-layer perceptron neural networks. A functional decomposition...
-
Multiaxial Fatigue Behaviour of SLM 18Ni300 Steel
PublikacjaFatigue behaviour of SLM 18Ni300 steel under proportional bending-torsion loading is studied. The fatigue tests are conducted under pulsating loading conditions using tubular specimens with a transversal circular hole. Three ratios of the normal stress to shear stress are considered, namely σ/τ=4,σ/τ=2 and σ/τ = 4/3. Crack initiation sites were found for two diametrically opposite points around the hole, whose locations are governed...
-
Multi-layered mineral glass units used as viewport elements of underwater ship structures
PublikacjaIn the paper, Authors deals with viewport elements of underwater marine constructions. If a single-plate viewport constructions are considered, big thicknesses of the glass plate are required to resist the pressure. To build the viewports from the commercially accessible glass panes, multi-layered glass units are proposed in the paper. Numerical calculations are presented, summarized and compared with experimental tests. Focusing...
-
Multiple jets impingement – numerical analysis by the ζ-f and hybrid VLES turbulence models
PublikacjaPresented paper summarizes the Authors findings referring to the numerical analyses of the jet impinging phenomena in the case of complex jets configurations in various applications e.g. in the heat exchangers. Multiple jets interference resulting in the cross-flow and the surface curvature are the factors which impose the need of advanced turbulence models utilization. The outcome of the research based on the ζ-f turbulence model...
-
Nanostructure of the laser-modified transition metal nanocomposites for water splitting
PublikacjaAlthough hydrogen is considered by many to be the green fuel of the future, nowadays it is primarily produced through steam reforming, which is a process far from ecological. Therefore, emphasis is being put on the development of electrodes capable of the efficient production of hydrogen and oxygen from water. To make the green alternative possible, the solution should be cost-efficient and well processable, generating less waste...
-
NONLINEAR VIBRATION ANALYSIS OF BEAM AND PLATE WITH CLOSED CRACK: A REVIEW
PublikacjaThe effect of nonlinearity is high sensitivity in damage detection, especially for closed cracks and delamination. This review illustrates the results of several researchers dealing with nonlinear effects caused by the closure of cracks in the structure, i.e., beam and plate structures. Early detection of damage is an important aspect for the structure and, therefore, continuous progress is being made in developing new and effective...
-
Notch fatigue analysis and life assessment using an energy field intensity approach in 7050-T6 aluminium alloy under bending-torsion loading
PublikacjaThis paper studies the fatigue crack initiation and fatigue crack propagation of notched cylindrical bars made of 7050-T6 aluminium alloy subjected to multiaxial bending-torsion loading. The sites of crack initiation and the angles of crack initiation were successfully predicted from the distribution of the first principal stress at the notch surface. Fatigue crack initiation lives were computed through the new concept of energy...
-
Numerical analysis of CO2-water separation in a horizontal double T-junction
PublikacjaCarbon dioxide is considered one of the main factors leading to global warming. Considering the significant impacts of CO2 on climate change, various technologies have been developed in recent decades to control carbon emission, such as for example CO2 capture and storage. The developed cycle of a negative CO2 emission power plant includes some devices, out of which, separator plays an indispensable role. To this end, T-junction...
-
Numerical analysis of high temperature minichannel heat exchanger for recuperative microturbine system
PublikacjaConsidering the development of energy sector, distributed small-scale power generation, e.g., gas micro-CHP, is attracting considerable interest. In such installations, the heat exchanger is one of the key components possessing a significant influence on overall performance. Most studies concentrate on units operating below 900C, which do not fulfil the requirements of gas micro-CHP. Therefore, there remains a challenge to design...
-
Numerical analysis of vacuum drying of a porous body in the integrated domain
Publikacjan the present study, the vacuum drying process of an apple slice is numerically modeled based on a control volume method. Transient two-dimensional Navier– Stokes, energy, moisture, and Luikov equations are solved by numerical coding (Fortran) to simulate the simultaneous heat and mass transfer in the ambient and apple slice, respectively. The privilege of using Luikov's model is that the capillary forces are considered, and a...
-
Numerical methodology for evaluation the combustion and emissions characteristics on WLTP in the light duty dual-fuel diesel vehicle
PublikacjaThe worldwide aim of reducing environmental impact from internal combustion engines bring more and more stringent emission regulations. In 2017 by EU has been adopted new harmonized test procedure called WLTP. In general terms this test was designed for determining the levels of harmful emissions and fuel consumption of traditional and hybrid cars. This procedure contains specific driving scenarios which representing reallife driving...
-
Numerical Modelling of Forced Convection of Nanofluids in Smooth, Round Tubes: A Review
PublikacjaA comprehensive review of published works dealing with numerical modelling of forced convection heat transfer and hydrodynamics of nanofluids is presented. Due to the extensive literature, the review is limited to straight, smooth, circular tubes, as this is the basic geometry in shell-and-tube exchangers. Works on numerical modelling of forced convection in tubes are presented chronologically in the first part of the article....
-
Ocena własności dynamicznych silnika z zapłonem samoczynnym na podstawie zmian wartości wskaźnika działania.
PublikacjaW artykule przedstawiono koncepcję metody pozwalającej na ocenę działania silnika pracującego na charakterystyce regulatorowej w nagłej zmiany obciążenia i związanej z tym akceleracji/deceleracji. Do analizy przebiegu zmian podstawowych własności użytkowych silnika w tym czasie wykorzystane zostało wartościujące (ilościowe) ujęcie działania interpretowanego jako pewna wielkość fizyczna. Podejście takie umożliwia jednoczesne uwzględnienie...
-
On reliability assessment of ship machinery system in different autonomy degree; A Bayesian-based approach
PublikacjaAnalyzing the reliability of autonomous ships has recently attracted attention mainly due to epistemic uncertainty (lack of knowledge) integrated with automatic operations in the maritime sector. The advent of new random failures with unrecognized failure patterns in autonomous ship operations requires a comprehensive reliability assessment specifically aiming at estimating the time in which the ship can be trusted to be left unattended....
-
On the Use of Selected 4th Generation Nuclear Reactors in Marine Power Plants
PublikacjaThis article provides a review of the possibility of using different types of reactors to power ships. The analyses were carried out for three different large vessels: a container ship, a liquid gas carrier and a bulk carrier. A novelty of this work is the analysis of the proposal to adapt marine power plants to ecological requirements in shipping by replacing the conventional propulsion system based on internal combustion engines...
-
On the use of the cumulative strain energy density for fatigue life assessment in advanced high-strength steels
PublikacjaIn this paper, the applicability of the cumulative strain energy density is explored as a fatigue indicator parameter for advanced high-strength steels subjected to strain-controlled conditions. Firstly, the cyclic stress-strain responses of nine steels, selected from three multiphase families, encompassing different elemental compositions and different heat treatment routes, were studied. Then, the predictive capabilities of the...
-
Opracowanie deskryptora nawierzchni drogowej do oceny oporu toczenia opon samochodowych
PublikacjaNa początku niniejszej pracy pt. „Opracowanie deskryptora nawierzchni drogowej do oceny oporu toczenia opon samochodowych” przedstawiono zagadnienia dotyczące oporów ruchu pojazdu. Omówiono metody zarówno drogowe, jak i laboratoryjne badań oporu toczenia opon samochodowych. Zaprezentowano przykładowe wartości współczynników oporu toczenia opon na różnych rodzajach nawierzchni. Kolejno omówiono metody pomiaru tekstury nawierzchni....
-
Opracowanie technologii naprawy nieciągłości metalicznych w połączeniach spawanych, w konstrukcji podpór przednich pras filtracyjnych położonych na terenie Grupowej Oczyszczalni Ścieków Dębogórze
PublikacjaCelem niniejszej pracy jest opracowanie wytycznych technologicznych, których wdrożenie pozwoli na usunięcie istniejących pęknięć, co przyczyni się do stabilizacji wymiarowej podpór oraz całej konstrukcji pras. Osiągniecie tego celu wymaga podjęcia następujących działań: - ocenę stanu technicznego naprawianego komponentu- podpór przednich trzech pras filtracyjnych, - określenie własności spawalniczych materiału naprawianego, -...
-
Optimization of biocorrosion resistance and mechanical properties of PM Ti–XAl–2Fe–3Cu alloys by response surface methodology
PublikacjaIn the current study, the biocorrosion resistance and mechanical properties of the Ti–XAl–2Fe–3Cu (wt%) (X = 6, 4, 2 wt%) alloy produced by powder compact extrusion of blended elemental powders were optimized by using the response surface methodology in order to gain the best combination of processing parameters. To run the optimization process, central composite design with three equal levels of oxygen, hydrogen and aluminum was...
-
OVERALL SET OF BANDSAW TEETH VERSUS METHODS OF MEASUREMENTS
PublikacjaThis article deals with the impact of the manual methods of measurement on the overall set measurement results. It describes the results of the measurement of bandsaw teeth kerf with the use of a micrometer and a digital calliper. It is commonly known that the cutting process causes the wear of cutting tools. The wear of the cutting edge depends on the cutting conditions as well as on the mechanical properties of the processed...
-
PORÓWNANIE DZIAŁANIA POPRZECZNYCH ŁOŻYSK ŚLIZGOWYCH NA ZMODERNIZOWANYM STANOWISKU DYDAKTYCZNYM
PublikacjaW artykule przedstawiono autorską metodę porównania działania poprzecznych łożysk ślizgowych na podstawie wyników badań wykonanych na zmodernizowanym stanowisku laboratoryjnym. Modernizacja stanowiska składającego się ze źródła mocy w postaci silnika elektrycznego napędzającego dwa wały połączone sprzęgłem i zakończone łożyskiem wzdłużnym przekazującym siłę naporu. Podłączenie przetwornika częstotliwości umożliwiło pracę silnika...
-
Preliminary studies on the effect of feed speed on the colour change of wood
PublikacjaThis paper presents the results of preliminary analyses of the effect of cutting parameters on changes in the colour of wood. Beech wood cut with use circular saw was analysed. The cutting parameter tested was the feed speed, represented by the feed per tooth. Sawing processes with different feed per tooth ranging from 0.0008 mm to 0.09 mm were analysed. It was observed that over the entire range of feed rate per tooth analysed,...
-
Probing Local Structural Changes by Sharp Luminescent Infrared Nanophosphor for Application in Light-Emitting Diodes
PublikacjaCr3+-doped infrared phosphors are promising candidates for next-generation phosphor-converted infrared light-emitting diodes (LEDs) because they can, in principle, tune and convert the luminescence spectra from an LED chip. However, most studies focus on broad-band Cr3+-doped phosphors, and the control mechanism of Cr3+-doped phosphors with sharp line emissions remains ambiguous. Here, we report LiGa5(1–x)Al5xO8:Cr3+ phosphors...
-
Problematyka implantacji protez piersiowych - przegląd literatury
PublikacjaOperacje związane z wykorzystaniem implantów piersi są jednymi z najczęściej przeprowadzanych zabiegów chirurgii plastycznej, dlatego istotne jest, aby zminimalizować ryzyko powikłań. Do najczęściej występujących zalicza się: obrzęk, wysięk, krwiaki, problemy z gojeniem ran oraz infekcje. Zakłada się, że infekcja jest głównym czynnikiem prowadzącym do degradacji implantu. Agresywne środowisko gospodarza, ciągłe zmiany pH i temperatury...
-
Problems associated with the up of actuating system of a single-disc lapping machine for flat surfaces
PublikacjaPrzedstawiono wyniki badań nagrzewania się podstawowych elementów układu wykonawczego docierarki jednotarczowej o standardowej kinematyce do obróbki powierzchni płaskich. Analizowano przyrost temperatury zespołu napędowego, rolek i pierścieni prowadzących separatory oraz tarczy docierającej i obrabianych elementów. Badano nagrzewanie się układu obróbkowego podczas wyrównywania żeliwnego narzędzia i docierania powierzchni płaskich....
-
Production and Properties of the Porous Layer Obtained by the Electrochemical Method on the Surface of Austenitic Steel
Publikacja: The growing demand for implants has seen increasing interest in the introduction of new technologies and surface modification methods of metal biomaterials. This research aimed to produce and characterize a porous layer grown on austenitic stainless steel 316L, obtained via the anodization process near the micro-arc oxidation, i.e., low voltage micro-arc oxidation (LVMAO). The discussed layer significantly influences the properties...
-
PROJEKT I WDROŻENIE ZAAWANSOWANEGO SYSTEMU TELEMETRII DO POMIARÓW ZACHOWANIA BOLIDU FORMULA STUDENT
Publikacjapracy przedstawiono proces projektowania i wytworzenia zaawansowanego systemu telemetrii, który został zaaplikowany w piątej generacji bolidu stworzonego przez zespół PGRacing Team. Zastosowanie tego rozwiązania pozwoliło na optymalizację konstrukcji i ustawienia zawieszenia pojazdu. Zebrane dane pochodzą z sensorów, w których skład wchodzą m. in. GPS, akcelerometr, czujniki temperatury opon, liniowe czujniki skoku zawieszenia,...
-
Properties of chitosan/CuNPs coatings electrophoretically deposited on TiO2 nanotubular oxide layer of Ti13Zr13Nb alloy
PublikacjaCoatings based on chitosan/CuNPs (chit/CuNPs) were obtained by a one-step electrophoretic deposition (EPD) on nanotubular oxide layer of Ti13Zr13Nb alloy. The deposition was carried out for 1 min applying voltages of 10 and 20 V with and without the addition of dispersing agent (Polysorbate 20) to the suspension. The coatings obtained for the lower voltage were more uniform than for the higher voltage. By adding a dispersing agent,...
-
Properties of New Composite Materials Based on Hydroxyapatite Ceramic and Cross-Linked Gelatin for Biomedical Applications
PublikacjaThe main aim of the research was to develop a new biocompatible and injectable composite with the potential for application as a bone-to-implant bonding material or as a bone substitute. A composite based on hydroxyapatite, gelatin, and two various types of commercially available transglutaminase (TgBDF/TgSNF), as a cross-linking agent, was proposed. To evaluate the impacts of composite content and processing parameters on various...
-
Przegląd metod wytwarzania energii elektrycznej z wodoru i ocena potencjału ich zastosowania w krajowym systemie elektroenergetycznym
PublikacjaW artykule dokonano przeglądu dostępnych metod wytwarzania energii elektrycznej z udziałem technologii wodorowych i podjęto próbę oceny potencjału ich zastosowania w polskim systemie elektroenergetycznym. Szczególną uwagę poświęcono ogniwom paliwowym, omawiając dostępne na rynku typy ogniw oraz ich podstawowe parametry techniczne. W zakresie technologii wodorowych, rozważono możliwość samodzielnej pracy ogniw paliwowych, turbin...
-
"Raport z wstępnych badań własności stali trudnościeralnej 460HB",. ang "Report on preliminary tests of the properties of wear-resistant steel 460HB"
PublikacjaMikrostrukturę badanej stali trudnościeralnej 460HB stanowi drobnoziarnisty martenzyt odpuszczony, który jest właściwy dla stali konstrukcyjnych niskowęglowych, niskostopowych ulepszonych cieplnie. W przypadku blach grubych, do których zalicza się badana stal, struktura może ulec zaburzeniu, jeżeli w hutniczym procesie wytwórczym wystąpiła niejednorodność odkształcenia plastycznego i w konsekwencji tworzenie się pasm segregacyjnych,...
-
Reliability of acicular grindable thermocouples for transient temperature measurements at sliding contacts
PublikacjaAcicular grindable thermocouples represent an interesting and prospective technique of temperature measurements at sliding contacts. This study aimed at the investigation of their reliability and accuracy as applied to the friction materials of various classes in contact with steel. The tests were conducted on a pin-on-disc tribometer under stationary and transient regimes. The experimental results were validated by comparing the...
-
Rheology of Variable Viscosity‐Based Mixed Convective Inclined Magnetized Cross Nanofluid with Varying Thermal Conductivity
PublikacjaCross nanofluid possesses an extraordinary quality among the various fluidic models to explore the key characteristics of flowing fluid during very low and very high shear rates and its viscosity models depend upon shear rate. The current study establishes the numerical treatment regarding variable viscosity‐based mixed convective inclined magnetized Cross nanofluid with var‐ ying thermal conductivities over the moving permeable...
-
Simulation of hybridized nanofluids flowing and heat transfer enhancement via 3-D vertical heated plate using finite element technique
PublikacjaThe present study probed the creation of heat energy and concentrating into Newtonian liquids across vertical 3D-heated plates. The role of the Soret and Dufour theories in concentrating and energy formulas is discussed. The role of hybrid nanoparticles is introduced to illustrate particle efciency in terms of solute and thermal energy. It is removed a viscous dissipation process and a changing magnetic feld. The proposed approach...
-
Slowly-closing valve behaviour during steam machine accelerated start-up
PublikacjaThe paper discusses the state of stress in a slowly-closing valve during accelerated start-up of a steam turbine. The valve is one of the first components affected by high temperature gradients and is a key element on which the power, efficiency and safety of the steam system depend. The authors calibrated the valve model based on experimental data and then performed extended Thermal-FSI analyses relative to experiment. The issue...
-
Some new soliton solutions to the higher dimensional Burger–Huxley and Shallow water waves equation with couple of integration architectonic
PublikacjaIn this paper, we retrieve some traveling wave, periodic solutions, bell shaped, rational, kink and anti-kink type and Jacobi elliptic functions of Burger’s equation and Shallow water wave equation with the aid of various integration schemes like improved -expansion scheme and Jacobi elliptic function method respectively. We also present our solutions graphically in various dimensions.
-
Stability investigation of the PCM nanocomposites
PublikacjaIn present study was showed the results of research the stability of nanoPCMs in terms of types and concentrations of surfactant used. For stearic acid has been added PVP or oleic acid in concentrations of 0%, 5% and 10%. Nanoparticles TiO2 and Al-2O3 in concentration of 1% were chosen to be researched in this test. The mixing of nanocomposites has been done in an ultrasonic scrubber in which the samples were placed for 45 mins....
-
Stirling engines - the state of technology development and computational models
PublikacjaStirling engines represent a technologically important solution in combined heat and power systems. Their use enables the achievement of over 90 percent efficiency in the management of the primary energy source with a very high durability of the device, mainly due to the lack of contact of the working gas with external factors and a very small number of mechanical components. The use of a Stirling engine may be equally important...
-
Struktury oraz mapy przepływu R1233zd w okrągłym minikanale przy średnich i wysokich wartościach ciśnienia zredukowanego [w:] Postępy w badaniach wymiany ciepła i masy
PublikacjaW wiedzy dotyczącej struktur przepływu niskowrzących czynników roboczych w zakresie wysokich temperatur nasycenia (powyżej 120°C) oraz średnich i wysokich wartościach ciśnienia zredukowanego (0.5-0.9) występuje luka. W literaturze obecne są dane dotyczące podobnych wartości ciśnień zredukowanych, ale dla niższych wartości temperatury nasycenia (głównie z zakresu -20°C do 40°C). Wynika to z dotychczasowych zastosowań chłodniczych...
-
Study of the Layer-Type BST Thin Film with X-ray Diffraction and X-ray Photoelectron Spectroscopy
PublikacjaIn the present paper, results of X-ray photoelectron studies of electroceramic thin films of barium strontium titanate, Ba1xSrxTiO3 (BST), composition deposited on stainless-steel substrates are presented. The thin films were prepared by the sol-gel method. A spin-coating deposition of BST layers with different chemical compositions was utilized so the layer-type structure of (0-2) connectivity was formed. After the deposition,...
-
Tailoring Diffusional Fields in Zwitterion/Dopamine Copolymer Electropolymerized at Carbon Nanowalls for Sensitive Recognition of Neurotransmitters
PublikacjaThe importance of neurotransmitter sensing in the diagnosis and treatment of many psychological illnesses and neurodegenerative diseases is non-negotiable. For electrochemical sensors to become widespread and accurate, a long journey must be undertaken for each device, from understanding the materials at the molecular level to real applications in biological fluids. We report a modification of diamondized boron-doped carbon nanowalls...
-
TEMPERATURE INFLUENCE ON TIRE ROLLING RESISTANCE MEASUREMENTS QUALITY
PublikacjaGlobal warming makes it necessary to reduce energy consumption, which in the case of motor vehicles, is connected, among other things, with reduction of resistive forces acting on a vehicle during its motion. One of the most important components of those forces is rolling resistance, which is very difficult to measure, especially in road conditions. The article deals with issues related to the influence of the thermal state of...
-
The effect of beech wood (Fagus sylvatica L.) steaming process on the colour change versus depth of tested wood layer
PublikacjaThe results of experimental research on the colour changes of beech wood at different depths of the tested layer are presented. Beech wood (Fagus sylvatica L.) dried in a conventional kiln was tested. Half of the wood samples were steamed prior to the drying process. Colour changes were measured at various depths after the face milling process was used to remove the material to expose to the deeper surface. The colour changes were...
-
The Effect of Openings’ Size and Location on Selected Dynamical Properties of Typical Wood Frame Walls
PublikacjaThe wooden frame constructions are now popular in many developed countries of the world. Many of these locations where such buildings are constructed are exposed to seismic and other shocks which are generated by human activities. This paper discusses the effect of the size and location of openings in the wooden frame walls under dynamic loadings. Natural frequencies of such frames with and without openings have been determined....
-
The effect of Sr and Mg substitutions on structure, mechanical properties and solubility of fluorapatite ceramics for biomedical applications
PublikacjaIonic substitutions play important role in the modifications of biological apatites. Recently, attention has been focused on the co-doping effects on the functional properties of apatite-based biomaterials. In this research work, the dense samples of fluorapatites, Ca10(PO4)6F2 and Ca8MgSr(PO4)6F2, were produced after sintering at 1250 °C for 6 h in air. Structural characterization carried out with XRD, IR, Raman and SEM, confirmed...
-
The Effects of Pin Profile on HDPE Thermomechanical Phenomena during FSW
PublikacjaFriction stir welding (FSW) of polymeric materials has recently attracted significant attention. Herein, we present the effect of the tool pin profile on the FSW of high-density polyethylene (HDPE) joints through joint experimental analysis and thermomechanical simulations. For analysis of pin profile effects on the thermomechanical properties of HDPE joints, frustum (FPT), cubic (CPT), and triangular (TPT) pin shapes were selected...
-
The energy approach to fatigue crack growth of S355 steel welded specimens subjected to bending
PublikacjaThe study presents the results of the research on the rate of fatigue crack growth subjected to bending in the ferritic-pearlitic structure. The studies were carried out at a constant amplitude of the moment and at various values of the load ratios R and at the operating frequency of the machine of 28.4 Hz. Flat specimens made of S355 steel and with fillet welds and with double-sided blunt external notches as well as concave...