Publikacje
Filtry
wszystkich: 59
Katalog Publikacji
-
Experimental research on water lubricated marine stern tube bearings in conditions of improper lubrication and cooling causing rapid bush wear
PublikacjaWater lubricated bearings are popular in sliding bearings of marine propeller shafts, turbines and pump shafts. Such popularity is partly due to their simple construction which also means a relatively affordable price. In practical experience one may also observe cases of rapid wear or even malfunctions of this bearings, some of which may be caused by insufficient flow of lubricant leading to overheating. The conducted...
-
Experimental research on water lubricated three layer sliding bearing with lubrication grooves in the upper part of the bush and its comparison with a rubber bearing
Publikacjacomposite. Eachofitslayershasanimportantfunction.Speciallypreparedslidingsurfaceensures minimum resistance.Followingrunning-initssmoothnessbecomesveryhighandthebearingmay continue workingunder fluid lubricationregime.NBRlayerensuresbearingelasticity,goodvibration damping propertiesandinsusceptibilitytoshaftaxismisalignment.Theexternalbrasslayermakes fitting thebearingeasier. Experiment resultsoftheconductedresearchwerecomparedwiththoseforarubberbearingof similar...
-
Influence of local bush wear on water lubricated sliding bearing load carrying capacity
PublikacjaOne of main problems concerning water-lubricated bearings is their durability. There are known cases of bearings with life time measured in decades, and some, whose refurbishment was necessary just days after start-up. Obtaining stable fluid film friction plays key role in the durability of these bearings. Unfortunately, their load-carrying capacity is limited due to water's low-viscosity. The conducted experimental...
-
Water-lubricated stern tube bearing - experimental and theoretical investigations of thermal effects
PublikacjaThe paper presents research results of thermal phenomena accompanying operation of a water-lubricated stern tube bearing with axial grooves. Experimental tests revealed, that intensity of forced axial flow has strong influence on bush temperature. Numerical simulations focused on investigation of the thermal phenomena under operation of water-lubricated journal bearing showed, that restricted axial flow promotes backflow of the...
-
Properties comparison of rubber and three layer PTFE-NBR-bronze water lubricated bearings with lubricating grooves along full bush circumference based on experimental tests
PublikacjaWater lubricated bearings have been in industrial use for well over a century. During the last decade their traditional range has been expanded with new, modern products. Despite that fact, certain solutions continue to employ the standard rubber bearing with lubricating grooves located along entire bush circumference. The work presents experimental research conducted on comparable sliding bearings with lubrication grooves along...
-
Water-lubricated bearings of ship propeller shafts - problems, experimental tests and theoretical investigations
PublikacjaW pracy przedstawiono problemy związane z projektowaniem, montażem i ekspolatcją smarowanych wodą łożysk okrętowych wałów głównych.Przedstawiono wyniki prowadzonych prac badawczych ekperymntalnych i obliczeń.
-
Influence of main design parameters of ship propeller shaft water-lubricated bearings on their properties
PublikacjaW artykule omówiono wpływ głównych parametrów konstrukcyjnych i eksploatacyjnych takich jak wielkość luzu łożyskowego, własności materiału panwi, stanu powierzchni skojarzenia ślizgowego oraz temperatury i zasolenia wody na nośność hydrodynamiczną łożyska okrętowego wału śrubowego smarowanego wodą.
-
Water-Lubricated Sintered Bronze Journal Bearings—Theoretical and Experimental Research
PublikacjaWater lubricated bearings are used from many years in shipbuilding, hydro power and other industries because of their advantages such as: extensive serviceable life, low coefficient of friction, longevity of shaft sleeve, good abrasion resistance, low maintenance required, unit simplicity, no danger of pollution and low price. Various types of water lubricated sliding bearings have been tested at the Technical University of Gdansk...
-
Experimental Research on the Energy Efficiency of a Parallel Hybrid Drive for an Inland Ship
PublikacjaThe growing requirements for limiting the negative impact of all modes of transport on the natural environment mean that clean technologies are becoming more and more important. The global trend of e-mobility also applies to sea and inland water transport. This article presents the results of experimental tests carried out on a life-size, parallel diesel-electric hybrid propulsion system. The eciency of the propulsion system was...
-
A comparative performance assessment of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublikacjaThis work presents the investigation results of a journal bearing lubricated with magnetorheological fluid that is activated by a local constant magnetic field to vary both the local flow resistance and pressure. The bearing performance is assessed via Finite Element Modelling (FEM) and results are corroborated by experiments. The FEM model uses the Bingham model to describe the fluid film. A dedicated test rig is used to assess...
-
Marine propeller shaft bearings under low-speed conditions: water vs. oil lubrication
PublikacjaThe bearings used in shipbuilding, hydropower, and water pumps have undergone a metamorphosis in recent decades. Because of environmental regulations, lubrication with grease or mineral oil is prohibited. Thus, the standard solutions include water-lubricated bearings with polymer bushings or sealed systems lubricated with oil. When properly designed, assembled, and operated, bearings can operate reliably for years. However, specific...
-
Multi-source-supplied parallel hybrid propulsion of the inland passenger ship STA.H. Research work on energy efficiency of a hybrid propulsion system operating in the electric motor drive mode
PublikacjaIn the Faculty of Ocean Engineering and Ship Technology, Gdansk University of Technology, design has recently been developed of a small inland ship with hybrid propulsion and supply system. The ship will be propelled by a specially designed so called parallel hybrid propulsion system. The work was aimed at carrying out the energy efficiency analysis of a hybrid propulsion system operating in the electric motor drive mode and at...
-
Energy Demand of Short-Range Inland Ferry with Series Hybrid Propulsion Depending on the Navigation Strategy
PublikacjaInterest in hybrid propulsion systems that can be used on small vessels has increased significantly in recent years. They can replace inefficient and environmentally burdensome conventional systems based on diesel engines. Hybrid propulsion has many advantages such as high energy efficiency and virtually noiseless operation, and therefore it fits well with the current trends of “green shipping” and “zero emission”. The aim of the...
-
ENERGY EFFICIENT AND ENVIRONMENTALLY FRIENDLY HYBRID CONVERSION OF INLAND PASSENGER VESSEL
PublikacjaThe development and growing availability of modern technologies, along with more and more severe environment protection standards which frequently take a form of legal regulations, are the reason why attempts are made to find a quiet and economical propulsion system not only for newly built watercraft units, but also for modernised ones. Correct selection of the propulsion and supply system for a given vessel affects significantly...
-
Design Methodology for Small Passenger Ships On the Example of the Ferryboat Motława 2 Driven by Hybrid Propulsion System
PublikacjaDynamic development in practically all elds of science and engineering has not passed over shipbuilding . In last years , engineers got to their use computer soware which makes it possible to perform strength and hydrodynamic calculations as well as to visualize design projects in 3 D space [1-4]. At their disposal they have full spectrum of modern solutions associated with the use of advanced materials and technologies [5-7]....
-
ENERGY EFFICIENT SMALL INLAND PASSENGER SHUTTLE FERRY WITH HYBRID PROPULSION - CONCEPT DESIGN, CALCULATIONS AND MODEL TESTS
PublikacjaIn recent years, there has been a significant development in “green” and energy efficient propulsion systems, which fits into the general trend of environmentally friendly “green shipping”. The pursued goal is to construct a safe passenger ship that is low in energy demand and equipped with a highly energy efficient, emission-free propulsion system. The paper presents main problems encountered by designers of a small, hybrid-powered...
-
The influence of polymer bearing material and lubricating grooves layout on wear of journal bearings lubricated with contaminated water
PublikacjaThe goal of the present paper is to investigate wear properties of journal sliding bearing operating in the conditions of contaminated water lubrication. Several bearing materials and bearing sleeve designs (differing in the axial grooves position and their shape) were tested experimentally under typical operating conditions in a dedicated test rig, which was equipped with a lubricating system, enabling lubrication with contaminated...
-
Influence of local bush wear on properties of water lubricated marine stern tube bearings
PublikacjaW artykule przedstawiono propozycję metody obliczania łożysk ślizgowych smarowanych cieczą o niskiej lepkości (wodą) w których doszło do lokalnego zużycia panwi. Proponowana metoda uwzględnia sprężystą deformację panwi (model EHL) oraz zmianę geometrii będącą wynikiem zużycia.
-
Experimental research on marine oil-lubricated stern tube bearing
PublikacjaBearings of propeller shafts are very crucial elements of the propulsion system of each of the ships. The safety of shipping depends on their durability and reliability. The new legal restrictions mean that today we are looking for environmentally friendly solutions. That is why water-lubricated bearings are becoming more and more popular. So, will oil-lubricated shaft bearings belong to the past? The bearing with a white metal...
-
Selected Problems of Experimental Testing Marine Stern Tube Bearings
PublikacjaThis paper presents typical methods for conducting experimental tests on main shaft slide bearings. There are described their possible testing capabilities, advantages, drawbacks and limitations. Various testing methods were analyzed to find a solution able of providing a wide range of possible investigations at possibly acceptable limitations.
-
Small Vessel with Inboard Engine Retrofitting Concepts; Real Boat Tests, Laboratory Hybrid Drive Tests and Theoretical Studies
PublikacjaThe development of modern technologies and their increasing availability, as well as the falling costs of highly ecient propulsion systems and power sources, have resulted in electric or hybrid propulsions systems’ growing popularity for use on watercraft. Presented in the paper are design and lab tests of a prototype parallel hybrid propulsion system. It describes a concept of retrofitting a conventionally powered nine meter-long...
-
The catamarans George and Energa Solar
PublikacjaReferat prezentuje unikalne jednostki: George - katamaran zasilany siłą mięśni i Energa Solar - zasilany energią słoneczną.
-
Badania eksperymentalne polimerowego łożyska smarowanego wodą okrętowego wału śrubowego.
PublikacjaReferat prezentuje część wyników uzyskanych w trakcie badań eksperymentalnych polimerowego łożyska okrętowego wału głównego smarownego wodą. Zademonstrowano uzyskane w trakcie pracy badawczej wykresy współczynnika tarcia,rozkładu ciśnienia na obwodzie pomiędzy czopem a panwią oraz trajektorii środka czopa.
-
Shaft Misalignment Influence on Water Lubricated Turbine Sliding Bearings with Various Bush Modules of Elasticity
PublikacjaW artykule przeanalizowano wpływ wielkości przenoszenia osi wału względem panwi na nośność łożyska. Analizie poddano łożyska z odmiennymi rodzajami panwi o różnej sztywności.
-
Novel Design of an Ocean Wave Power Device
PublikacjaW artykule przedstawiono nowoczesną boję energetyczną o opatentowanej konstrukcji. Omówiono jej konstrukcję oraz przedstawiono problemy konstrukcyjne i badawcze. W ostatniej części artykułu przedstawiono wyniki badań wykonanych na modelu w basenie modelowym.
-
Influence of surface roughness topography on properties of water lubricated polymer bearings, experimental research
PublikacjaW artykule przedstawiono wyniki badań eksperymentalnych, których celem było zidentyfikowanie wpływu ułożenia chropowatości na powierzchni ślizgowej łożyska smarowanego wodą z polimerową panwią. Badania wykazały, że wpływ ten jest mniejszy niż oczekiwano a na własności łożyska ma wpływ głównie wysokość chropowatości.
-
Projekt i budowa regatowo-badawczej łodzi zasilanej energią słoneczną
PublikacjaW artykule opisano proces projektowania i budowy małej regatowej jednostki pływajacej zasilanej energią słoneczną. Opisano statrt w regatch Frisian Solar Challenge, które odbyły się w Holandii w 2010r.
-
Assessment of possible application of water lubricated sintered brass slide bearing for marine propeller shaft
PublikacjaW artykule przedstawiono wyniki badań eksperymentalnych smarowanego wodą łożyska poprzecznego z panwią wykonaną ze spieku brązu.Przedstawiono wyniki pomiarów rozkładu ciśnienia w filmie smarnym, trajektorie osi wału oraz oporów ruchu.Przeprowadzono ocenę przydatności tego typu łożyska do łożyskowania okrętowych wałów śrubowych.
-
Badania polimerowych łożysk ślizgowych wału śrubowego małej jednostki pływającej.
PublikacjaReferat prezentuje założenia oraz wyniki wstępnych badań teoretycznych i eksperymentalnych smarowanych wodą polimerowych łożysk ślizgowych wału śrubowego małej jednostki pływającej. Głównym problemem badawczym jest wyjaśnienie czy w smarownych wodą panwiach wału śrubowego możliwe jest uzyskanie stabilnego smarowania hydrodynamicznego. Autor przedstawia model obliczeń teoretycznych oraz specjalnie zaprojektowane i wykonane...
-
Badania symulacyjne polimerowych łożysk ślizgowych wału śrubowego małej jednostki pływającej.
PublikacjaReferat prezentuje założenia oraz wyniki wstępnych badań symulacyjnych smarowanych wodą polimerowych łożysk ślizgowych wału śrubowego małej jednostki pływającej. Prezentowany jest model teoretyczny izotermiczny oraz wyniki obliczeń numerycznych wykonanych za jego pomocą.
-
Research on heavy loaded water lubricated main shaft bearings of the ship = Badania mocno obciążonych, smarowanych wodą łożysk wału śrubowego jednostki pływającej
PublikacjaW referacie zaprezentowano wyniki badań łożyska z polimerową panwią smarowanego wodą, jednego z wiodących producentów. Próby prowadzono dla dwóch odmiennych warunków pracy: dla typowych wielkości obciążeń, jakie występują w łożysku rufowym okrętowego wału głównego oraz dla obciążeń, przy których średnie naciski są bliskie wartościom dopuszczalnym, określonym przez producenta. Przeprowadzone badania wykazały, że łożysko pracuje...
-
First tests of water lubricated propeller shaft bearings = Wstępne badania zespołu smarowanych wodą łożysk okrętowego wału śrubowego
PublikacjaW pierwszej części referatu zaprezentowano nowe stanowsko badawcze przy pomocy którego można badać smarowane wodą łożyska wału śrubowego. W drugiej części pracy przedstawiono uzyskane wyniki pomiarów oporów ruchu i trajektorii osi wału.
-
Hybrydowe łożysko okrętowego wału głównego smarowane wodą - koncepcja i pierwsze badania eksperymentalne.
PublikacjaReferat dotyczy okrętowych łożysk wałów śrubowych z polimerową panwią smarowanych wodą. Przedstawiono w nim wybrane wyniki badań łożyska z typową panwią oraz łożyska z tą samą panwią, ale z nieco zmienionym kształtem rowków smarnych. Zmiana ta, wprowadzona przez autorów, miała na celu polepszenie warunków wytworzenia się hydrodynamicznego filmu smarnego i zapewnienia pracy łożyska przy tarciu płynnym, czego nie stwierdzono w łożysku...
-
Research work on water lubricated polymer hydrodynamic bearings.
PublikacjaW pierwszej części artykułu w skrócie omówiono stanowisko badawcze na którym przeprowadzono eksperyment. W drugiej części opisano symulowane warunki pracy łożyska i zaprezentowano wyniki badań. Z przeprowadzonej analizy rezultatów wynika, że jest możliwe uzyskania tarcia płynnego w okrętowym łożysku wału śrubowego z polimerową panwią smarowanym wodą.
-
Badania wodnego filmu smarnego w łożyskach wału śrubowego wykonanych z tworzyw sztucznych.
PublikacjaPraca dotyczy smarowanych wodą łożysk ślizgowych okrętowego wału śrubowego z panwiami wykonanymi z polimerów. W pierwszej części pracy przebadano eksperymentalnie typową panew jednego ze znanych producentów łożysk oraz panew własnej konstrukcji.W drugiej części pracy przeprowadzono obliczenia numeryczne łożysk ślizgowych. Następnie porównano otrzymane wyniki i wyciągnięto wnioski.
-
Influence of bush wear in water lubricated marine stern tube bearings with shaft misalignment
PublikacjaWater lubricated propeller shaft bearings are frequently employed on modern ships due to their advantages such as durability, simplicity and low price. Specific working conditions on ships cause shaft misalignment which often results in rapid wearing of bush and shaft. Shaft misalignment could be an effect of manufacturing or assembly faults but sometimes it appears due to hull or shaft deformation. The wearing process has influence...
-
WATER LUBRICATED MAIN SHAFT BEAR INGS WITH THREE LAYER BUSH – MODERN SOLUTION FOR MARINE INDUSTRY
PublikacjaWater lubricated sliding bearings are increasingly popular in marine and hydro power industry. Such popularity is partly due to their simple construction which also means a relatively affordable price. Properly designed and installed water lubricated bearings may well last for over a decade. During the last decade their traditional range has been expanded with new, modern products like three layer bearing bush. The work presents...
-
ATTEMPT AT EVALUATING THE INFLUENCE OF BENDING STRESS ON SHAFT WEAR PROCESSES IN WATER LUBRICATED SLIDING BEARING WITH A RUBBER BUSHING
PublikacjaWater lubricated bearings find increasingly wide application in shipbuilding or hydro–power industry, the popularity stemming from their numerous advantages. Unfortunately, as it turns out, water lubricated bearings do not always meet expectations, as on occasion they become subject to intense, premature wear which requires costly repair. One of the still unexplained phenomena is the process of excessive bearing wear, in particular...
-
Projekt małego promu pasażerskiego z napędem hybrydowym – koncepcja napędu i wybrane problemy gospodarowania energią
PublikacjaNowoczesne i ekologiczne układy napędowe zyskują coraz większą popularność. Ze względu na wzrost świadomości społeczeństwa oraz restrykcyjne przepisy odnośnie ochrony środowiska w najbliższych latach konwencjonalne układy napędowe mogą nie zostać dopuszczone do dalszej eksploatacji. Dobór alternatywnego rozwiązania jest zależny od wielu czynników, jak na przykład od rodzaju akwenu, po którym porusza się jednostka pływająca, jej...
-
Research on water lubricated main shaft bearings in conditions of improper lubrication and cooling conducted on high torque real-life scale bush test rig
PublikacjaWater lubricated polymer bushes find increasingly popular use in the sliding bearings of marine propellers, water turbines and pump shafts. Such popularity is partly due to their simple construction which also means relatively affordable price. In addition, properly designed and installed water lubricated bearings may well last for over a decade. However, in practical experience one may also observe cases of rapid wear...
-
Polymer journal bearings behaviour research under limited lubrication and cooling conditions conducted on high torque test rig
PublikacjaPolymer journal bearings are frequently used as a water-lubricated bearings of small marine units’ propeller shafts . Choice of these bearings is based on their simple construction and relatively low purchase and maintenance costs. Although properly designed and installed water lubricated bearings may well last for over a decade, rapid wear or failure of these bearings can be observed...
-
Propozycja modernizacji układu napędowego pasażerskiego statku śródlądowego z konwencjonalnego na hybrydowy
PublikacjaNa przestrzeni ostatnich lat zaobserwowano znaczny wzrost zainteresowania ekologicznymi układami napędowymi rekreacyjnych oraz użytkowych jednostek pływających, wpisującymi się w nurt przyjaznej środowisku, bez emisyjnej, zielonej żeglugi. Problemem jest jednak skonstruowanie bezpiecznej dla pasażerów jednostki pływającej, o możliwie niskim zapotrzebowaniu na energię, wyposażonym w wysoko sprawny, bez emisyjny układ napędowy....
-
Analiza konstrukcji ramy nośnej wyczynowego roweru wodnego Rektor na przykładzie wybranego węzła
PublikacjaW pracy poruszono problem zmniejszenia masy wyczynowego roweru wodnego Rektor bez utraty jego wytrzymałości. W tym celu przeprowadzone zostały wieloetapowe obliczenia wybra- nego węzła konstrukcyjnego. Ponadto omówiono technologię wykonania rur kompozytowych. Podczas analizy sprawdzono trzy przypadki różniące się materiałem, z którego wykonano ramę, odpowiednio: z aluminium, laminatu zbrojonego włóknem szklanym oraz laminatu zbrojonego...
-
Influence of Bearing Bush Geometry on Properties of Water Lubricated Marine Main Shaft Bearings
PublikacjaW pracy przedstawiono wpływ geometrii smarowanego wodą, okrętowego łożyska ślizgowego wału głównego na jego własności hydrodynamiczne.Wykazano, że wielkość luzu łożyskowego, położenie oraz liczba rowków smarnych mają znaczący wpływ na nośnosć łożyska.
-
Experimental tests of water lubricated marine rubber bearing
PublikacjaW referacie przedstawiono stosowane obecnie rodzaje łożysk gumowych smarowanych wodą. Omówiono ich zalety i wady.W drugiej części pracy przedstawiono wyniki badań eksperymantalnych typowego okrętowego łożyska gumowego. Uzyskane rezultaty porównano z wynikami badań łożysk z polimerową panwią.
-
Ekologiczne zasilanie i napędy małych statków i łodzi
PublikacjaArtykuł dotyczy nowoczesnych układów napędu niewielkich jednostek pływających opartych na silnikach elektrycznych z magnesami trwałymi ziem rzadkich oraz układów ich zasilania. Przedstawiono różne typy nowoczesnych silników, akumulatorów oraz paneli fotowoltaicznych. Zaprezentowano obecne trendy rozwoju oraz przedstawiono jednostki pływające zasilane energią słoneczną zaprojektowane i zbudowane na Politechnice Gdańskiej.
-
Numeryczna analiza trójwymiarowego przepływu w polimerowym łożysku smarowanym wodą = Numerical analysis of three dimensional flow in water lubricated bearing with polymer bearing bush
PublikacjaW referacie przedstawiono wyniki obliczeń łożysk smarowanych wodą w oparciu o metodę CFD - obliczeniowej mechaniki płynów. Wykazano przydatność nowoczesnych narzędzi obliczeniowych do rozwiązywania podobnych problemów.
-
Wpływ chropowatości na pracę hydrodynamicznego łożyska smarowanego wodą z polimerową panwią
PublikacjaW referacie przedstawiono wyniki przeprowadzonych badań eksperymantalnych, których celem było zbadanie wpływu ułożenia i wysokości chropowatości na pracę łożyska smarowanego wodą.
-
Katamaran ''Energa Solar'' zasilany energią słoneczną = Solar energy ''Energa Solar'' catamaran
PublikacjaReferat prezentuje unikalną jednostkę zasilaną energią słoneczną ENERGA Solar.
-
Sukces mimo wszystko
PublikacjaAutor jest opiekunem Koła Naukowego Studentów ''KORAB'', działającego przy Wydziale Oceanotechniki i Okrętownictwa Politechniki Gdańskiej. W artykule zaprezentowano katamaran zasilany energią słoneczną, który został zaprojektowany i zbudowany z myślą o starcie w międzynarodowych regatach Frisian Nuon Solar Challenge.W artykule opisano start w regatach, które odbyły się latem 2006r.