Wyszukiwarka
ISSN:
eISSN:
Wydawca:
Dyscypliny:
- inżynieria mechaniczna (Dziedzina nauk inżynieryjno-technicznych)
Punkty Ministerialne: Pomoc
| Rok | Punkty | Lista |
|---|---|---|
| Rok 2024 | 40 | Ministerialna lista czasopism punktowanych 2024 |
| Rok | Punkty | Lista |
|---|---|---|
| 2024 | 40 | Ministerialna lista czasopism punktowanych 2024 |
| 2023 | 40 | Lista ministerialna czasopism punktowanych 2023 |
| 2022 | 40 | Lista ministerialna czasopism punktowanych (2019-2022) |
| 2021 | 40 | Lista ministerialna czasopism punktowanych (2019-2022) |
| 2020 | 40 | Lista ministerialna czasopism punktowanych (2019-2022) |
| 2019 | 40 | Lista ministerialna czasopism punktowanych (2019-2022) |
| 2018 | 11 | B |
| 2017 | 11 | B |
| 2016 | 11 | B |
| 2015 | 11 | B |
| 2014 | 6 | B |
| 2013 | 6 | B |
| 2012 | 5 | B |
| 2011 | 5 | B |
| 2010 | 6 | B |
Model czasopisma:
Impact Factor:
Polityka wydawnicza:
- Licencja
-
otwiera się w nowej karcie
- Informacja o polityce wydawniczej
- brak danych
- Informacja o warunkach samoarchiwizacji
- Zawarta w licencji
- Czy czasopismo pozwala na samoarchiwizację
- Tak - bez ograniczeń
- Informacje o polityce dot. danych badawczych
- brak danych
- Embargo w miesiącach
- brak embargo
- Informacje dodatkowe
-
Przy samoarchiwizacji / rozpowszechnianiu należy podać źródło oryginału.
Typ licencji Creative Commons podany przy artykułach.
Prace opublikowane w tym czasopiśmie
Filtry
wszystkich: 6
Katalog Czasopism
Rok 2018
-
Influence of fasteners and connections flexibility on deflections of steel building including the stressed skin effect
PublikacjaThe paper presents the analysis of the influence of fasteners and connections flexibility on displacements of symmetrical single-bay pitched-roof steel building, including trapezoidal cladding acting as a diaphragm. The purpose of the article was to compare numerical models with and without taking into consideration fasteners and connections flexibility in order to observe the differences in transverse stiffness of the building...
Rok 2017
Rok 2016
-
Flexural behaviour of concrete slabs reinforced with FRP bars in experiments and according to aci ACI 440.1R guide
PublikacjaThe paper presents research conducted on two concrete slabs reinforced with the carbon composite bars and two other concrete slabs reinforced with basalt composite bars. The carbon bars were plain, while the basalt ones were ribbed. The slabs were experimentally investigated in the flexural state of effort with the concentrated forces applied. The results are compared with the analytical solution proposed in the guide ACI 440.1R-06...
Rok 2015
-
Point cloud unification with optimization algorithm
PublikacjaTerrestrial laser scanning is a technology that enables to obtain three-dimensional data – an accurate representation of reality. During scanning not only desired objects are measured, but also a lot of additional elements. Therefore, unnecessary data is being removed, what has an impact on efficiency of point cloud processing. It can happen while single point clouds are displayed – user decides what he wants...
Rok 2014
-
Derivation of the scaling laws used in geotechnical centrifuge modelling-application of dimensional analysis and Buckingham Π theorem
PublikacjaGeotechnical centrifuge modelling has been a world-wide used technology in physical tests. In this paper a derivation of scaling laws by dimensional analysis for the centrifugal modelling is presented. Basic principles of centrifuge modelling are described. Scaling laws for slow events like consolidation and fast events like dynamic loads are shown. The differences in scale factors for both processes are noticed. The aim of this...
Rok 2013
-
Impact of optimization of ALS point cloud on classification
PublikacjaAirborne laser scanning (ALS) is one of the LIDAR technologies (Light Detection and Ranging). It provides information about the terrain in form of a point cloud. During measurement is acquired: spatial data (object’s coordinates X, Y, Z) and collateral data such as intensity of reflected signal. The obtained point cloud is typically applied for generating a digital terrain model (DTM) and a digital surface model (DSM). For DTM...
wyświetlono 946 razy