Filtry
wszystkich: 18
Wyniki wyszukiwania dla: OVERHEATING
-
The FEM analysis of pressure installation elements after simulated accidental overheating
PublikacjaThe paper presents innovative analysis focused on the safety aspects of existing pressure installation operation after overheating accidents. Results presented here can be applied in decision-making process concerning further operation of existing pressure installation after cooling system failure. In this paper the results of FEM analysis performed for a straight pipe and 90 degrees elbow, made of super duplex stainless steel,...
-
Overheating of underground power cable line due to its partial exposition to solar radiation
PublikacjaCurrent-carrying capacity of underground power cable lines depends, among others, on thermal resistivity of the soil and cables layout: trefoil formation, flat formation with or without spacing. If conditions for heat transfer in the ground are favorable, the current-carrying capacity is relatively high. Therefore, it generates risk of the power cables overheating, if part of the cable line is located vertically in the air, to...
-
The Dilemmas of Choosing a Suitable Technology for Low Energy and Passive Houses in the Context of their Overheating Issues
PublikacjaIn compliance with European Union directives, numerous countries are introducing increasingly stricter legal limits on the estimated energy consumption of newly designed residential buildings. However, the fact, that regulations and designers' efforts are focused on decreasing energy consumption (and consequently carbon dioxide emissions) only at the post-occupancy stage, may lead to a significant increase in the carbon footprint...
-
Possibilities of Increasing the Overall Efficiency of Gas-steam CHP Microplant
PublikacjaThe paper presents ways to increase the efficiency of a gas-steam micro power plant by modifying the cycle combination. The modification consists in partial release of the fluid downstream of the gas turbine and using it for ORC fluid overheating and evaporation. Advantages of this solution over the simplest gas and steam cycles’ combination are demonstrated.
-
Risk of power cables insulation failure due to the thermal effect of solar radiation
PublikacjaLow-voltage, as well as high-voltage power cable lines, are usually buried in the ground. The ampacity of the power cables in the ground mainly depends on the thermal resistivity of the soil, which may vary in a wide range. A common practice in power cable systems performance is to supply them from a pole of an overhead line. If so, a section of the line is located in free air and can be directly exposed to solar radiation. In...
-
Temperature distribution of supercapacitors prepared by various technologies
PublikacjaSupercapacitors, also known by different names such as electrostatic double-layer capacitors (EDLCs) or ultra-capacitors, are electrical storage devices still in development. These devices require fast and reliable methods of assessing their state-of-health. Thermographic imaging is a method which can be applied with this aim due to its popularity, and the high negative impact of overheating on a supercapacitor’s parameters. Moreover,...
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublikacjaIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (s), were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublikacjaIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (),were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
Experimental research on water lubricated marine stern tube bearings in conditions of improper lubrication and cooling causing rapid bush wear
PublikacjaWater lubricated bearings are popular in sliding bearings of marine propeller shafts, turbines and pump shafts. Such popularity is partly due to their simple construction which also means a relatively affordable price. In practical experience one may also observe cases of rapid wear or even malfunctions of this bearings, some of which may be caused by insufficient flow of lubricant leading to overheating. The conducted...
-
Thermal stabilization and permanent deformation resistance of LWA/PCM-modified asphalt road surfaces
PublikacjaThis paper presents the results of attempts at reducing the problem of solar overheating of asphalt road pavement surfaces, resulting in weakening and accelerated destruction of the aforementioned structures. To protect pavement surfaces against periodic overheating, standard asphalt mixture AC 16 W 35/50, used for binder course, has been modified by replacing one of the aggregate fractions from the mineral mixture with lightweight...
-
Empirical Relationship Describing Total Convective and Radiative Heat Loss in Buildings
PublikacjaOn the basis of theoretical considerations of convective-radiative heat transfer, a relationship was developed enabling the total convective and radiative heat flux QC+R emitted from any object at tw and its surroundings at t∞ to be calculated from known values of the surface temperature of such an object, i.e., the known temperature difference Δt=tw - t∞ and average air temperature Tav. This relationship is applied to thermal...
-
Problems of varistor quality assessment during exploitation
PublikacjaVaristors are commonly used elements which protect power supply networks against high-voltage surges or lightning. Therefore, quality and endurance of these elements is important to avoid losses when an expensive laboratory equipment would not be protected from random overvoltages. Additionally, excessive leakage currents generate serious costs due to high energy consumption. The paper presents shortly properties of varistors that...
-
Research on water lubricated main shaft bearings in conditions of improper lubrication and cooling conducted on high torque real-life scale bush test rig
PublikacjaWater lubricated polymer bushes find increasingly popular use in the sliding bearings of marine propellers, water turbines and pump shafts. Such popularity is partly due to their simple construction which also means relatively affordable price. In addition, properly designed and installed water lubricated bearings may well last for over a decade. However, in practical experience one may also observe cases of rapid wear...
-
The use of lightweight aggregate saturated with PCM as a temperature stabilizing material for road surfaces.
PublikacjaThis paper presents the possibility of adding lightweight building aggregates to increase the stability – mechanical as well as thermal - of constructions and road objects. This stability can be achieved through saturating the porous granules of aggregate with a phase-change material (PCM) that allows the accumulation of solar heat. Intense solar radiation, especially during the summer, can cause the asphalt on road surfaces, bridges...
-
Protection System Design of Induction Motor for Industries
PublikacjaThe fundamental and durable structures of induction motor, as well as their low manufacturing cost, make them popular components in a wide range of current applications. Providing a safety net for employees is a must-have for businesses. This project’s motivation for improvement is to provide industrial motors, lift motors, pumps, and so on with safety. An induction motor’s primary goal is to protect it from problems, such as...
-
Protection System Design of Induction Motor for Industries
PublikacjaThe fundamental and durable structures of induction motor, as well as their low manufacturing cost, make them popular components in a wide range of current applications. Providing a safety net for employees is a must-have for businesses. This project’s motivation for improvement is to provide industrial motors, lift motors, pumps, and so on with safety. An induction motor’s primary goal is to protect it from problems, such as...
-
Investigation of the thermal effects in water-lubricated journal bearings with axial grooves
PublikacjaWater-lubricated hydrodynamic journal bearings are frequently applied as stern tube bearings due to their advantages over other bearing types. They are environmentally friendly, can operate without sealings and in conditions of low friction losses. The most popular are bearings with open axial grooves, which require, for proper operation, forced axial flow of the lubricating water. Correctly designed and operated stern tube bearings...
-
Evaluation of fire hazard in electrical installations due to unfavorable ambient thermal conditions
PublikacjaEvaluation of fire hazard caused by electrical installations is a difficult and important topic, and it limits the possibility of loss of life or health of people, as well as the occurrence of significant property damage. In particular, this hazard was caused by power cables and especially photovoltaic (PV) installations. The authors proved that power cables directly exposed to strong solar radiation are likely to exceed maximum...