Filtry
wszystkich: 1165
-
Katalog
- Publikacje 1069 wyników po odfiltrowaniu
- Czasopisma 1 wyników po odfiltrowaniu
- Konferencje 1 wyników po odfiltrowaniu
- Osoby 6 wyników po odfiltrowaniu
- Laboratoria 1 wyników po odfiltrowaniu
- Kursy Online 14 wyników po odfiltrowaniu
- Wydarzenia 1 wyników po odfiltrowaniu
- Dane Badawcze 72 wyników po odfiltrowaniu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: MULTIPARTITE DISTILLABLE KEY
-
Pounding between Inelastic Three-Storey Buildings under Seismic Excitations
PublikacjaStructural interactions between adjacent, insufficiently separated buildings have been repeatedly observed during damaging ground motions. This phenomenon, known as the structural pounding, may result in substantial damage or even total collapse of structures. The aim of the present paper is to show the results of the nonlinear numerical analysis focused on pounding between inelastic three-storey buildings under seismic excitations....
-
Experimental verification and comparison of mode shape-based damage detection methods
PublikacjaW pracy przedstawiono wynik badań eksperymentalnych dotyczących oceny dokładności znanych z literatury metod detekcji uszkodzeń konstrukcji wykorzystujących zmiany jej parametrów modalnych. Pomiary wykonano wykorzystując skaner laserowy firmy Polytec. Omówiono sposoby poprawy jakości uzyskiwanych wyników, oraz zaproponowano własną metodę detekcji uszkodzeń wykorzystującą pomiar postaci i częstości drgań własnych konstrukcji.
-
Transmission and reflection coefficients for damage identification in 1D elements
PublikacjaW pracy przedstawiono mozliowści wykorzystania współczynnika odbicia i przejścia fali sprężystej w miejscu nieciągłości konstrukcji do identyfikacji jej rodzaju
-
Damage Detection Using Cointegration Technique and Wavelet Analysis of the Post-Cointegrated Lamb Waves
Publikacja -
Diagnosis of Damage in a Steel Tank with Self-Supported Roof through Numerical Analysis
PublikacjaThe safety of civil engineering structures is one of the most important issues of building industry. That is why the assessment of the damage-involved structural response has recently become of major concern to engineers. Among a number of different approaches to diagnosis of damage, the method of measuring the changes in natural frequencies is considered to be one of the most effective indicators of global damage. From the practical...
-
High Speed Milling vibration surveillance with optimal spindle speed based on optimal speeds map
PublikacjaThe paper presents the method of the surveillance of the self-excited chatter vibration. At first, the workpiece modal parameters are estimated based on experimental data which leads to verification of computational model. Then, for selected surface points optimal spindle speeds are calculated. By considering sufficient amount of points it is possible to build a map of optimal spindle speeds. Experimental results show that this...
-
Analysis of Rolling Resistance of Tires With Run Flat Insert
PublikacjaRun flat properties are required for tires intended for special applications like military or rescue vehicles. Run-Flat inserts make possible to drive a car or truck, with certain restrictions, also when inflation pressure is very low or non-existing (after tire damage). Rolling resistance of tires rolling the inserts increases considerably in relation to the rolling resistance of properly inflated tires. This paper presents results...
-
Diffusible Hydrogen Control in Flux Cored Arc Welding Process
PublikacjaOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper an experimental...
-
Modal parameters identification with Particle Swarm Optimization
PublikacjaThe paper presents method of the modal parameters identification based on the Particle Swarm Optimization (PSO) algorithm [1]. The basic PSO algorithm is modified in order to achieve fast convergence and low estimation error of identified parameters values. The procedure of identification as well as algorithm modifications are presented and some simple examples for the SISO systems are provided. Results are compared with the results...
-
Road texture influence on tire rolling resistance
PublikacjaTire rolling resistance is one of the most important resistive forces acting on road vehicles. It depends on tire and surface characteristics as well as vehicle operating parameters. This paper deals with the influence of road surface texture on rolling resistance of passenger car tires. Results of road measurements performed on variety of road surfaces are presented.
-
Analysis and Comparison of Safety of Children and Adult Passenger in Car Based on Crash Tests Results
PublikacjaMost important features of the child seat were presented. There was made analysis of selected dynamic loads acting on mannequins heads during a collision. Comparison of loads acting on the kid in a child seat and the other passengers in a car is presented. In analysis of the results particular attention has been paid on the children's secure in a car. The phenomena of collision child's occipital bone with seat backrest was described....
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublikacjaThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Damage-involved response of two colliding buildings under non-uniform earthquake loading
PublikacjaPounding between insufficiently separated buildings, which may result in considerable damage or may even lead to the total collapse of colliding structures, has been repeatedly observed during earthquakes. Earthquake-induced collisions of buildings has been intensively studied applying various structural models. It was assumed in the analyses, however, that the seismic excitation is identical for all structural supports; whereas,...
-
Generative Process Planning with Reasoning based on Geometrical Product Specification
PublikacjaThe focus of this paper is on computer aided process planning for parts manufacture in systems of definite process capabilities, involving the use of multi-axis machining centers for parts shaping and grinding machines for finishing. It presents in particular a decision making scheme for setup determination as a part of generative process planning. The planning procedurę consists of two stages. The first stage is associated with...
-
On Software Unit Testing For Improving Security And Performance Of Distributed Applications
PublikacjaPerformance and security are software (SW) application attributes situated on the opposite corners of system design. In the most drastic example the most secure component is the one totally isolated from the outside world, with communication performance reduced to zero level (e.g. disconnected physically from the network, placed inside a Faraday cage to eliminate possible wireless accessibility). On the other hand the most performance-optimized...
-
The analysis of turbine propulsion systems in nuclear submarines
PublikacjaThe article systematises submarines, which are presently in service, according to their propulsion types (both conventional and nuclear), power output, and submersion depth. Contemporary types of propulsion systems installed and used in submarines are discussed. Calculations were performed for the PWR (Pressurized Water Reactor) type nuclear propulsion system and the supercritical turbine propulsion system (supercritical reactor...
-
Selected Problems of Cogeneration Energy Systems Designing, Fueled with Landfill Biogas
PublikacjaThe article discusses the impact of the quality of biogas fuel for operation of generating sets with internal combustion engines. There are presented selected investigation results of landfill biogas fueled gensets operation. The article includes also discussion of the possibility of increasing the efficiency of biogas fuelled cogeneration systems. It also presents guidelines for the optimal design of landfill biogas fueled engines,...
-
Hertzian Crack Propagation in Ceramic Rolling Elements
PublikacjaThe properties of ceramics are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such crack are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations are based on a three dimensional model for the ring crack propagation. The stress intensity factors along crack...
-
Lean Six Sigma in French and Polish Small and Medium-Sized Enterprises - The Pilot Research Results
PublikacjaThe article presents results of the research conducted in Polish and French small and medium-sized enterprises referring to the context of the implementation and application of the concept of Lean Six Sigma. The research was conducted in the form of case studies, observations and individual interviews. The pilot studies led to the identification of the needs, expectations, concerns and experiences of these companies. At the same...
-
Carbon dioxide potential reduction using Start-Stop system in a car
PublikacjaOperating fuel consumption increases significantly when the vehicle stops frequently while driving or when the engine is idling during braking. In such cases, the internal combustion engine consumes the fuel but the mechanical energy is not used by the drive system. The amount of fuel that is consumed in this time by the engine can potentially be saved if the car is equipped with a Stop-Start system. Start-Stop system automatically...
-
Effect of surface roughness on thermal-hydraulic characteristics of plate heat exchanger
PublikacjaIn the paper the experimental analysis of passive heat transfer intensification in the case of modeled plate heat exchanger is conducted. The plate heat exchanger is chosen for the analysis because this kind of heat exchangers could be prospectively applied in the ORC systems, however other areas or application are equally possible. The experimental setup was assembled at the Department of Energy and Industrial Apparatus of Gdansk...
-
Frequency response spectra applied to assess efficiency of the training techniques
PublikacjaThe purpose of the research is to assess the increase of the muscle strength and power. Movement of the human body when the moving one impacts a stationary or moving body is taken under consideration. The waveform produced by an impact is transformed into frequency domain. The acceleration record is transformed as a complex spectrum, by the use of a Discrete Fourier Transformation. In this paper the applications of the discrete...
-
Organic Rankine as bottoming cycle to a combined Brayton and Clausius-Rankine cycle
PublikacjaThis paper presents an enhanced approach, as it will be considered here that the ORC installation could be extra-heated with the bleed steam, a concept presented by the authors. In such way the efficiency of the bottoming cycle can be increased and an amount of electricity generated increases. A thermodynamic analysis and a comparative study of the cycle efficiency for a simplified steam cycle cooperating with ORC cycle will be...
-
The initial selection of parameters for dynamic brake for car engine test dynamometer
PublikacjaThe article presents an analysis of the car engine loads. The aim of the analysis was to determine the parameters of the brake / electric motor on an engine test bad. Analysis of loads on the driving tests concerned on chassis dynamo to simulate them on an engine dynamometer. To check the range of dynamometer shaft angular acceleration inertial mass of a car was reduced on the crankshaft axis. The calculations of maximum shaft...
-
Transmission and Reflection Coefficients for Damage Identification in 1D Elements
Publikacja -
Generative Process Planning with Reasoning Based on Geometrical Product Specification
Publikacja -
Experimental Study on Pounding between Structures during Damaging Earthquakes
PublikacjaMutual pounding between structures during earthquakes may cause serious structural damage. The aim of this paper is to show the results of a shaking table experimental study focused on pounding between structures in series under several earthquake excitations. The experiments were performed using three tower models with different configurations and different gap distances between them. In the first stage of the study, one rigid...
-
Enhancing the Seismic Resistance of Columns by GFRP Confinement Using Flexible Adhesive-Experimental Study
PublikacjaIn this paper, the results of two experiments, focused on testing the effectiveness of a method of enhancing the seismic (dynamic) resistance of masonry columns with the use of flexible polymer adhesive, are shown. The first experiment was devoted to investigate the damping properties of a polymer working between two stiff layers, whereas the aim of the second one was to verify if the identified damping properties of the polymer...
-
Numerical Analysis of a Steel Frame Building with Soft-storey Failure under Ground Motion Excitation
PublikacjaThe aim of this paper is to show the results of a numerical analysis focused on the behaviour of multi-storey steel frame building that suffers from a soft-storey failure under ground motion excitation. A numerical model of the structure was created in FEM computer software and was exposed to an impact that would have been generated after a soft-storey failure due to falling of the upper floors. During the analysis, the whole structure...
-
Diagnosis of Damage in a Steel Tank Model by Shaking Table Harmonic Tests
PublikacjaThe aim of the present paper is to show the results of the shaking table experimental study concerning the diagnosis of damage in a model of cylindrical steel tank with self-supported roof which is filled with liquid. During the tests, the base of the structure was excited under the harmonic loading with variable frequency. The tests were repeated for different stages of damage, which was introduced in the model by easing the bolts...
-
Compensation of pressure peaks in pwk-type hydraulic pumps
Publikacjahydraulic axial pumps equipped with cam-driven commutation unit (pwk pumps) proved their high efficiency up to 55 mpa and ability to work self-sucking, even at high speed. displacement of pwk pump may easily be changed by moving its control cam. full discharge from hydrostatic forces makes such control possible by direct action of a low-energy actuator like proportional electromagnet or stepping motor. that eliminates heavy and...
-
Shaft Misalignment Influence on Water Lubricated Turbine Sliding Bearings with Various Bush Modules of Elasticity
PublikacjaW artykule przeanalizowano wpływ wielkości przenoszenia osi wału względem panwi na nośność łożyska. Analizie poddano łożyska z odmiennymi rodzajami panwi o różnej sztywności.
-
Novel Design of an Ocean Wave Power Device
PublikacjaW artykule przedstawiono nowoczesną boję energetyczną o opatentowanej konstrukcji. Omówiono jej konstrukcję oraz przedstawiono problemy konstrukcyjne i badawcze. W ostatniej części artykułu przedstawiono wyniki badań wykonanych na modelu w basenie modelowym.
-
The Influence of Gas Mixture in the Glow-Discharge Nitriding Process of Austenitic Stainless Steel on Characteristic of Nitrided Cases
PublikacjaAustenitic stainless steels characterize with excellent corrosion resistance, although low mechanical properties. In many cases that limits their exploitation in industrial applications. Moreover, austenitic stainless steel is susceptible to local corrosion in the presence of halide ions. In present works, it was emphasized that the nitriding of austenitic stainless steels gives some potential abilities to obtain beneficial effect...
-
Crack propoagation in MgO-PSZ ceramic materials
PublikacjaThe properties of ceramic materials such as elevated hardness, high temperature capability, low coefficient of thermal expansion are of interest for rolling element materials. Widely used ceramic materials in engineering applications are silicon nitride, zirconia and alumina. The paper presents an experimental study of the fatigue life of MgO-PSZ ceramic material in lubricated contact with defined types of cracks. A ceramic angular...
-
A New Technique of Spine Disease Treatment Supported by ADRSK1 Device
Publikacja -
Numerical analysis of crack propagation in silicone nitride
PublikacjaThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculation...
-
Problems of analytical determination of journal bearing bush fatigue strength estimates
PublikacjaProblems connected with determination of stress distribution in sliding layer of thinwalled bearing bushes, investigated in bearing fatigue test rigs, have been presented. Using an example of plain bearings tested in the fatigue machine SMOK (built at the Gdask University of Technology) problems with obtaining a convergence of iterative procedure for determining the fatigue strength estimators of bearing alloy surface layer are...
-
Influence of design of hydraulic components on their operation in low ambient temperatures
PublikacjaW artykule przestawiono wpływ konstrukcji zespołów hydraulicznych na ich działanie w niskich temperaturach otoczenia.
-
Experimental Investigation of Prototype Water-Lubricated Compliant Foil Bearings
PublikacjaPraca zawiera wyniki badań doświadczalnych prototypowego łożyska foliowego smarowanego wodą. Łożyska tego typu mogą mieć zastosowanie w węzłach, od których wymaga się ekologicznego środka smarowego, np. pompy wodne czy turbiny wodne. W opracowaniu zademonstrowano wyniki badań trzech prototypowych poprzecznych łożysk foliowych. Opisano napotkane problemy badań oraz wprowadzonych do konstrukcji łożyska zmian, których celem była poprawa...
-
Non-linear behaviour of base-isolated building supported on flexible soil under damaging earthquakes
PublikacjaSeismic isolation is a strategy to reduce damage of structures exposed to devastating earthquake excitations. Isolation systems, applied at the base of buildings, lower the fundamental frequency of the structure below the range of dominant frequencies of the ground motion as well as allow to dissipate more energy during structural vibrations. The effectiveness of the base-isolated buildings in damage reduction has been confirmed...
-
Wear of Ultra-thin DLC or Tungsten-modified DLC Coatings under Reciprocating Sliding
PublikacjaIn the paper results are presented from tests in reciprocating sliding of self mated specimens of DLC and tungsten modified DLC coatings on stainless steel substrate. The contact geometry chosen for the research task was ball on flat. The contacts were lubricated either with distilled water or medical saline solution. Results are presented with regard to wear resistance as a function of material type and lubricant used.
-
Shaking table experimental study on damage mechanism of the disconnecting switch under seismic excitation
PublikacjaThe efficiency of the energetic network is a very import safety issue in the region experienced by the earthquake. High voltage disconnecting switches are important elements of the energetic infrastructure used to separate electric circuits (i.e. during repairs), which should not be damaged remaining fully operational. The aim of the paper is to show the results of the shaking table experimental investigation focused on damage...
-
Experimental study on polymer mass used to repair damaged structures
PublikacjaA new method of repairing damaged structures by injecting the cracks with specially designed polymer mass (flexible two-component grout based on polyurethane resin) has been recently proposed. The technique is mainly dedicated to damaged masonries, especially historical structures where minimum intervention is permitted. The cracks are filled with the special injection, forming the flexible joints bonding the disrupted structural...
-
Dynamics Conscious Approach to Tribometer Design and Tribo-testing
PublikacjaIn the paper findings are discussed on the issue of dynamic characteristics of a tribometer as a factor influencing the result of the tribological experiment. An advanced approach to tribo-testing is attempted with integrated dynamic analysis of the tribometer and the sliding pair. The fundamental idea is explored of the tribometer being regarded as any machine in which friction is inflicted with all the resulting consequences...
-
Modernization of the Trailer for Tyre/Road Rolling Resistance Measurements
PublikacjaIn the article the ways of defining tyre rolling resistance are presented. The advantages of the laboratory tests of tyre/road rolling resistance and the advantages and disadvantages of on the road tyre/road rolling resistance tests are described. The description of the special trailer used for tyre/road rolling resistance measurements designed and constructed in the Faculty of Mechanical Engineering at Gdansk University of Technology,...
-
Relieving the Measuring System of the Trailer for Tyre/Road Rolling Resistance Measurements from the Inertia Force
PublikacjaIn the article the principle of measuring of tyre/road rolling resistance tyres in road conditions applied in a special measuring trailer is presented. This trailer was built in Faculty of Mechanical Engineering at Gdansk University of Technology. The construction of two special devices used in this trailer was discussed. These devices eliminate the influence of some chosen confounding measurements factors such as: the inertia...
-
Use of Neural Networks in Diagnostics of Rolling-Element Bearing of the Induction Motor
PublikacjaBearing defect is statistically the most frequent cause of an induction motor fault. The research described in the paper utilized the phenomenon of the current change in the induction motor with bearing defect. Methods based on the analysis of the supplying current are particularly useful when it is impossible to install diagnostic devices directly on the motor. The presented method of rolling-element bearing diagnostics used indirect...
-
Numerical Comparison of Damping Amplification Effects Obtained in Neighborhood of a Mechanism Singular Position - Viscous and Electromagnetic Cases
PublikacjaIn the paper, results of numerical investigations are presented. A continuous beam is considered as the main vibrating element. Two energy dissipations methods are compared: viscous dampers and DC generators. To increase the damping effectiveness, velocity amplification is proposed, i.e., a mechanism is introduced between the beam and the damping element, and the mechanism configuration is set as closed to the singular position...
-
Damage-Involved Structural Pounding in Bridges under Seismic Excitation
PublikacjaDuring severe earthquakes, pounding between adjacent superstructure segments of highway elevated bridges was often observed. It is usually caused by the seismic wave propagation effect and may lead to significant damage. The aim of the present paper is to show the results of the numerical analysis focused on damage-involved pounding between neighbouring decks of an elevated bridge under seismic excitation. The analysis was carried...