Wyszukiwarka
Wyniki wyszukiwania dla: PEEK
-
Peculiarities associated with testing polyetheretherketone (PEEK) in a model rolling contact
PublikacjaPolyetheretherketone (PEEK) was investigated using a modified version of the four-ball tester in which the upper forth ball was replaced by a cone in such a way that kinematics of the four-ball configuration were fully preserved. Rotation of the cone enforced orbiting and rolling of the ceramic balls around the polymer cup. The results produced some unexpected peculiarities in the wear of ceramic balls which, in principle, should...
-
Hydrodynamiczne łożyska wzdłużne z warstwą ślizgową z PEEK
PublikacjaMonografia zawiera podsumowanie stanu wiedzy w zakresie hydrodynamicznych łożysk wzdłużnych z polimerową warstwą ślizgową uzupełnione o wyniki badań własnych autora w tym obszarze. W pierwszej części przedstawiono obszerny przegląd znanych z literatury wyników badań, a także opis doświadczeń eksploatacyjnych łożysk z wahliwymi segmentami z pokryciem powierzchni ślizgowej materiałami polimerowymi na bazie PTFE oraz PEEK. Materiały...
-
RESEARCH ON HYDRODYNAMIC PEEK JOURNAL BEARINGS LUBRICATED WITH WATER AND OIL
PublikacjaThe main purpose of the research was to determine the possibilities and experimentally test the benefits of replacing conventional oil lubrication with ecological water lubrication. Tests were carried out on a test rig for hydrodynamic radial bearings under conditions representative of the expected applications for the bearing in water turbines. Bearings made from the polymer material PEEK (polyether ether ketone) were tested under static...
-
WETTABILITY OF CHITOSAN-MODIFIED AND LIPID/POLYPEPTIDE-COATED PEEK SURFACES
Publikacja -
Characteristics of Hybrid Bioglass-Chitosan Coatings on the Plasma Activated PEEK Polymer
Publikacja -
Low-temperature air plasma modification of chitosan-coated PEEK biomaterials
Publikacja -
Effect of low-temperature plasma on chitosan-coated PEEK polymer characteristics
Publikacja -
Properties of PEEK-supported films of biological substances prepared by the Langmuir-Blodgett technique
Publikacja -
Characteristics of hybrid chitosan/phospholipid-sterol, peptide coatings on plasma activated PEEK polymer
Publikacja -
Tribological test for evaluation of Natural PEEK
Dane BadawczeTest of PEEK natural (beige color) samples with sliding speed up to 1,2 m/s and up to 8 MPa of nominal load
-
Tribological test for evaluation of CF30 Black PEEK
Dane BadawczeSample numner BL03 and BL04 made of PEEK CF30 (black color) tribologicaly tested with sliding speed up to 1,8 m/s and up to 14 MPa of nominal load under water lubrication.
-
Measurement file of PEEK 70 mm bushing measurements in original condition perforemed on custom-built 3d measuring stand
Dane BadawczeAfter manufacturing process (lathe turning) bearing was measured on custom bulit measurement stan developed during research project financed by National Centre of Science. Measurements consist of 110 000 points in 3D space taken on bushing inner surface. Bearing was measured taking vertical steps of 0,2 mm.
-
Badania procesu zużywania się polimerowych warstw ślizgowych na bazie materiału PEEK w styku czop-panew w warunkach tarcia mieszanego.
ProjektyProjekt realizowany w Katedra Konstrukcji Maszyn i Pojazdów zgodnie z porozumieniem UMO-2019/35/N/ST8/03313 z dnia 2020-07-07
-
Michał Wodtke dr hab. inż.
Osoby -
Measurement file of stainless stell shaft LSS1 and LSS2 with diameter 95,995 with 3d measurment device
Dane Badawcze3d point cloud consist of measured points on new stainless steel shaft used during testing hydrodynamic journal PEEK bearing.
-
Effect of Coating Material Properties on Tilting-pad Thrust Bearing Performance
PublikacjaPolymer lined tilting-pad bearings demonstrate many advantages over traditional bearing systems. Bearings with a polymer layer in comparison with a babbitted layer show, for example: lower value of friction coefficient (important during start/stops), higher fatigue strength of the coating, better distribution of the load on individual pads due to lower elasticity of the polymers, wider range of operational temperatures or the ability...
-
Compliance tests of the polymer layers used as hydrodynamic bearing coatings
PublikacjaOperational experience and scientific investigations results showed that polymer lined hydrodynamic bearings can withstand more severe operating conditions compared than white metal bearings. PTFE and PEEK-based coatings are the most frequently used as Babbitt alternatives. Both polymers differ significantly from the each other in material properties. According to catalogue data compression modulus of PTFE, it is about an order...
-
Experimental comparison of hydrodynamic thrust bearings with different pad surface materials
PublikacjaBabbitt is the material most frequently used as the pad surface material for hydrodynamic bearings operating at usual operating conditions. It shows many advantages important for safe bearing operation, as for example: low friction coefficient, corrosion resistance, fair mechanical properties and outstanding conformability. On the other hand, it is not free from disadvantages, such as limited fatigue strength or limited resistance...
-
Set of Experience Knowledge Structure (SOEKS) and Decisional DNA (DDNA): Past, Present and Future
PublikacjaThis article reviews research work on set of experience knowledge structure (SOEKS)-decisional DNA (DDNA) done in the past, ongoing, and planned for the future. Firstly, the concept of the knowledge representation technique of SOEKS-DDNA is discussed, and then an attempt is made to organize the past research related with it in chronological order. This work focuses on the review on SOEKS-DDNA, its application in different domains,...
-
Ecology In Tribology: Selected Problems of Eliminating Natural Oil-Based Lubricants from Machine Friction Couples
PublikacjaThe elimination of mineral oil-based lubricants from machines has multiple beneficial effects on the natural environment. Firstly – these lubricants are a direct threat to the environment in the event of leaks; secondly – their elimination reduces the demand for crude oil from which they are obtained. In addition, in many cases, e.g. when replacing traditional lubricants with water, friction losses in the bearings can also be reduced...
-
Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction
PublikacjaIn hydrodynamic bearings traditional bearing alloys: Babbitts and bronzes are most frequently utilized. Polymer sliding layers are sometimes applied as a valuable alternative. Hard diamond-like carbon (DLC) coatings, which are also considered for certain applications may show some advantages, as well. Although material selection is of secondary importance in a full film lubrication regime it becomes important in mixed friction...
-
Jan Stąsiek prof. dr hab. inż.
Osoby