Filtry
wszystkich: 46
Wyniki wyszukiwania dla: TILTING-PAD THRUST BEARING
-
Effect of Coating Material Properties on Tilting-pad Thrust Bearing Performance
PublikacjaPolymer lined tilting-pad bearings demonstrate many advantages over traditional bearing systems. Bearings with a polymer layer in comparison with a babbitted layer show, for example: lower value of friction coefficient (important during start/stops), higher fatigue strength of the coating, better distribution of the load on individual pads due to lower elasticity of the polymers, wider range of operational temperatures or the ability...
-
Effect of presence of lifting pocket on the THD performance of a large tilting-pad thrust bearing
PublikacjaHydrostatic assistance is a commonly used method to improve limited load carrying ability of tiltingpad thrust bearings during transient states of operation of vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves, etc.), it also requires manufacturing of special recesses/pockets at pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up...
-
Effect of the Presence of the Lifting Pocket on The THD Performance of a Large Tilting-Pad Thrust Bearing
PublikacjaIn this paper, an attempt was taken to study the effect of the lifting pocket on THD performance of a large tilting-pad thrust bearing of Itaipu power plant. B3earing performance was evaluated including recess shape for several cases of its depth. The results show, that hydrostatic recess changes calculated bearing properties quite significantly, especially in the vicinity of the pocket
-
Friction and Lubrication of Large Tilting-Pad Thrust Bearings
PublikacjaFluid film bearings have been extensively used in the industry because of their unbeatable durability and extremely low friction coefficient, despite a very low coefficient of friction dissipation of energy being noticeable, especially in large bearings. Lubricating systems of large tilting pad thrust bearings utilized in large, vertical shaft hydrogenerators are presented in this paper. A large amount of heat is generated due...
-
Study of the Influence of Heat Convection Coefficient on Predicted Performance of a Large Tilting-Pad Thrust Bearing
PublikacjaPart of the heat generated by the shearing of the lubricating film during operation of a hydrodynamic bearing is transferred to the bearing components. In the case of the pad, which is usually fully submerged in the lubricating oil, heat is further transferred at the pad free walls to the oil by convection. This mechanism causes a thermal gradient in a pad and, consequently, its thermal deflection. In large hydrodynamic thrust...
-
Performance peculiarities of PTFE-faced tilting-pad thrust bearings.
PublikacjaZastosowanie pokrycia powierzchni ślizgowej z PTFE pozwala na znaczącą poprawę właściwości łożysk wzdłużnych w trudnych warunkach pracy. Znanych jest wiele zastosowań takich łożysk głównie w turbinach wodnych w dawnym ZSRR i Chinach. Praca ta stanowi krótki przegląd specyficznych cech takich łożysk związanych między innymi ze specyfiką kompozytów na bazie PTFE. Omówiono wpływ podatności powierzchni ślizgowej na kształt powierzchni...
-
Tilting pad thrust bearing with novel material selection - experimental comparison of low and medium speed operation
PublikacjaThe advances in material engineering led to the development of hard carbon based coatings applied in numerous applications in order to prevent or minimize wear of the parts in contact. With Triondur® coatings, the bearing company Schaeffler has succeeded in halving the friction losses in the valve trains of passenger cars. The coatings are optimized for high abrasive wear protection and low sliding friction moments. Altogether...
-
On the Possibilities of Decreasing Power Loss in Large Tilting Pad Thrust Bearings
PublikacjaJournal Menu About this Journal Abstracting and Indexing Aims and Scope Article Processing Charges Articles in Press Author Guidelines Bibliographic Information Citations to this Journal Contact Information Editorial Board Editorial Workflow Free eTOC Alerts Publication Ethics Submit a Manuscript Table of Contents Abstract Full-Text PDF Full-Text HTML...
-
Centrally Pivoted Tilting Pad Thrust Bearing with Carbon-Based Coated Collar—Experimental Results of Low- and Medium-Speed Operation
PublikacjaExperimental results of the research on a tilting pad thrust bearing with symmetrical pad support in the conditions of high loads and low speeds are presented in the paper. As described in the literature review, experimental results of tilting pad bearings at low speed/high load regime and transient conditions are rare. Unusual material selection - steel pad against a DLC-type coating on the collar was utilized. Such material combination...
-
Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction
PublikacjaIn hydrodynamic bearings traditional bearing alloys: Babbitts and bronzes are most frequently utilized. Polymer sliding layers are sometimes applied as a valuable alternative. Hard diamond-like carbon (DLC) coatings, which are also considered for certain applications may show some advantages, as well. Although material selection is of secondary importance in a full film lubrication regime it becomes important in mixed friction...
-
Equalization of pad loads in large tilting pad thtust bearing
PublikacjaW pracy przedstawiono przebieg projektowania zmodernizowanego łożyska wzdłużnego hydrogeneratora. Na podstawie eksploatacyjnych danych o zróżnicowaniu temperatury klocków łożyskowych, na drodze obliczeń elasto-termo-hydrodynamicznych, stwierdzono konieczność wyrównania rozkładu obciążenia na poszczególne klocki łożyska. Cel został osiągnięty poprzez wprowadzenie podatnego podparcia segmentów łożyska na sprężynach płytowych, których...
-
DESIGN AND THEORETICAL ANALYSIS OF A PROTOTYPE TILTING-PAD RADIAL BEARING WITH ADJUSTABLE CLEARANCE
PublikacjaThe article introduces a design and analysis results of a prototype ORC (organic Rankine cycle) turbo generator rotor assembly of 300kW power, supported by tilting-pad bearings of original design. The calculations were performed for a prototype turbo generator rotor. The shaft of this machine is supported with two radial bearings, lubricated with an unusual lubricant – a low-boiling-point agent. The main objective of the presented...
-
Effect of manufacturing errors of the pad sliding surface on the performance of the hydrodynamic thrust bearing
PublikacjaIn the present study, investigation of the effect of manufacturing errors on the performance of large tilting pad thrust bearings has been performed, following a CFD-based Thermohydrodynamic analysis of a single pad. A 3D model has been generated, including the pad, the lubricant film and the corresponding part of the collar. The pad has been assumed to be deformed about the pivot point, due to thrust loading. Manufacturing errors...
-
Improvement of Thrust Bearing Calculation Considering the Convectional Heating within the Space between the Pads
PublikacjaA modern thrust bearing tool is used to estimate the behavior of tilting pad thrust bearings not only in the oil film between pad and rotating collar, but also in the space between the pads. The oil flow in the space significantly influences the oil film inlet temperature and the heating of pad and collar. For that reason, it is necessary to define an oil mixing model for the space between the pads. In the bearing tool, the solutions...
-
Prospects of Decreasing Power Losses in a Hydrostatic Thrust Bearing
PublikacjaIn numerous machines, axial load is carried by tilting pad thrust bearings known since the beginning of 20th century. These bearings are commonly bath lubricated, which is simple, does not require any additional pumps, and, due to this, such systems are highly reliable. In a contemporary technology, however, minimization of friction losses became an important goal of machinery improvement. Calculations based on elementary rules...
-
HYDROSTATIC THRUST BEARING WITH REDUCED POWER LOSSES
PublikacjaIn many cases in rotating machinery, axial load is carried by tilting pad thrust bearings which have been developed since the beginning of 20th century. For high reliability and simplicity, most commonly the bearings are bath lubricated. In the times of sustainable development, however, minimization of friction losses becomes an important criterion for machinery assessment, and a strategic goal of their development. Performed calculations,...
-
Field Tests on Hydrodynamic and Hybrid Operation of a Bidirectional Thrust Bearing of a Pump-Turbine
PublikacjaIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Due to the bidirectional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Improvement of the thrust bearing calculation considering the convectional heating within the space between the pads
PublikacjaA modern thrust bearing calculation tool should consider not only the oil film between pad and rotating collar but also the space between the pads. The oil flow in the space has a significant influence on the oil film inlet temperature, the convectional cooling of pad and collar and should be included in the bearing calculation methods. The authors use a tool developed at Clausthal University of Technology in cooperation with the...
-
Field tests on hydrodynamic and hybrid operation of a bi-directional thrust bearing of a pump-turbine
PublikacjaIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Because of bi-directional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
HYDRODYNAMIC THRUST BEARINGS WITH POLYMER LINING
PublikacjaPolymeric linings of sliding surfaces of the hydrodynamic bearings have been used successfully for over 50 years. Despite of their long history of operation and research, they have not become wide spread in industrial applications. This fact may be surprising, considering th e conclusions that have been published concerning bearing operation and design. This paper summarizes the current...