Filtry
wszystkich: 632
wybranych: 509
Wyniki wyszukiwania dla: CIRCULAR WAVEGUIDE
-
Miniaturized Inline Bandpass Filters Based on Triple-Mode Integrated Coaxial-Waveguide Resonators
PublikacjaThis work presents a design technique to implement miniaturized cross-coupled bandpass filters in inline physical configurations based on triple-mode resonators. Triple-mode resonances are obtained by using integrated coaxial-waveguide cavity resonators. They consist of two coaxial conducting posts placed in the sidewalls of a rectangular waveguide cavity. In the proposed triplet, a transmission zero (TZ) can be positioned at any...
-
Low-Loss Mechanically Tunable Resonator and Phase Shifters in Groove Gap Waveguide Technology
PublikacjaThis research is focused on the design and realization of high-performance high-power variable phase shifters in groove gap waveguide technology. Specifically, it is shown that the unique characteristic of groove gap waveguides, which is its proper operation without the need for electrical connection between the top and bottom sections of the waveguide, can be used to design mechanically tunable devices. Using the proposed method,...
-
Pro-ecological technology of wood sawing with circular saw blades
PublikacjaW niniejszym artykule opisano możliwości materiało- i energooszczędnego przecinania piłami tarczowymi. Przedstawiono również przykłady efektów zastosowania proekologicznych technologii przecinania w przemyśle.
-
On Von Karman Equations and the Buckling of a Thin Circular Elastic Plate
PublikacjaWe shall be concerned with the buckling of a thin circular elastic plate simply supported along a boundary, subjected to a radial compressive load uniformly distributed along its boundary. One of the main engineering concerns is to reduce deformations of plate structures. It is well known that von Karman equations provide an established model that describes nonlinear deformations of elastic plates. Our approach to study plate deformations...
-
The effect of the power transmission of the spindle on the position of the circular saw teeth
PublikacjaNa dokładność przecinania ma decydujący wpływ położenie ostrzy piły tarczowej. W pracy analizowano przyczyny i błędy połozenia ostrzy piły w stosunku do przedmiotu obrabianego spowodowane odkształceniem wrzeciona wywołanym przez siły skrawania i siły pochodzące od napędu.
-
The Study of Geometry of the Selected Transition Curves in the Design of Circular Roads
Publikacja -
comparison of circular and rectangular narrow esps with longitudinal wire electrode
PublikacjaDiesel engines emit fine particles, which are harmful to human and animal health. There are several methods for decrease particulate emission from a diesel engines, but up to now, these methods are not enough effective or very expensive. An electrostatic precipitation was proposed as an alternative method for control of a diesel particulate emission. Therefore, narrow electrostatic precipitators (ESPs) have become a subject of...
-
Determination of geometry and positions of circular saw teeth with pinpoint accuracy.
PublikacjaEfekty ekonomiczne procesu przecinania sa współzależne z dokładnością użytego narzędzia szczególnie gdy ma sie do czynienia z cięciem piłą tarczową posiadajacą małe wartości rzazu. W tym przypadku wszelkie niedokładności geometrii ostrza w płaszczyznach natarcia i przyłożenia powinny być określone już na etapie wytwarzania pił. Dotyczy to również położenia ostrzy w kierunkach osiowym i promieniowym piły. Te wszystkie wspomiane...
-
Analysis of radial run-out of circular saw's cutting blades
PublikacjaW pracy przedstawiono analizę bicia promieniowego ostrzy pił tarczowych w procesie przecinania drewna. Analizę przeprowadzono na podstawie zróżnicowania grubości warstw skrawanych przez poszczególne ostrza piły. Dla przykładowej piły, zaprezentowano wyniki obliczeń przebiegów grubości warstw skrawanych przez poszczególne ostrza i grubości całkowitej warstwy skrawanej dla całej piły.
-
Allowable values of radial runout of circular saw blade teeth
PublikacjaW pracy przedstawiono graniczne wartości bicia promieniowego ostrzy pił na podstawie zaproponowanych kryteriów.
-
Sustainable Waste Management for Implementation of a Circular Economy Model in a Port
PublikacjaThe manuscript presents the management of waste from marine vessels and cargo handling companies in a selected European Union port. The main objective of the paper is to analyse and evaluate the existing waste management model in the port of Szczecin in the context of circular economy. The expert research carried out is aimed, inter alia, at identifying which of the solutions currently in use need to be improved from an environmental...
-
Bandwidth Dependence of the Propagation Channel in Circular Metallic BAN Environments
PublikacjaIn this paper, the bandwidth dependence of the propagation channel for Body Area Networks (BANs) in circular metallic environments is addressed and models are proposed to evaluate the appropriate short-term fading margins that should be considered as a function of the system bandwidth. The deployment of BANs in metallic indoor environments, such as ships, factories, warehouses and other similar environments, involves additional...
-
Optimization of chip removing system operation in circular sawing machine
PublikacjaThe paper presents the optimization of the wood chips removing system in the sliding table saw. Chips are generated during the cutting of the material. The attention was focused on the upper casing of mentioned system. The methodical experimental studies of the pressure distribution inside the casing during the wood chip removing operation for the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm were...
-
CFGFRPT Piles with a Circular Cross-Section and their Application in Offshore Structures
PublikacjaThe possibilities of using concrete piles in a polymer composite reinforced with glass fibres in offshore facilities were shown. Laboratory tests of CFGFRPT type piles compressed axially and in eccentric compression for the analysis of CFGFRPT piles were used. Methods of analysis of dynamic systems for mathematical modelling of the displacement of the hammer in the pile driving process were applied. The possibilities of combining...
-
EMPIRICAL ASSESMENT OF THE MAIN DRIVING SYSTEM OF THE CIRCULAR SAWING MACHINE
PublikacjaThe producers of panel saws tend to improve sawing accuracy and minimise a level of vibrations, to increase their competitiveness at the market. Mechanical vibrations in the main saw driving system, which level depend on a plethora independent factors, may really affect sawing accuracy and general machine tool vibrations. The objective of the research was to explore vibrations signals of the main spindle system, and to extract...
-
Experimental analysis of chip removing system in circular sawing machine
PublikacjaPaper presents analysis of the process of removing the wood chips generated during the cutting of the material on the circular sawing machine. The attention is focused on the upper cover of the chip removing system. Within the framework of the work a systematic experimental study of pressure distribution in the cover during operation of the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm was carried...
-
Stable and unstable bifurcation in the von Karman problem for a circular plate
PublikacjaW niniejszej pracy badamy równania von Karmana dla cienkiej, sprężystej, kołowej płyty, która znajduje się na sprężystym podłożu, pod działaniem sił ściskających wzdłuż swojego brzegu.Stosując metody analizy nieliniowej, dowodzimy istnienia stabilnychi niestabilnych punktów bifurkacji w zbiorze rozwiązań badanych równań.
-
A 3D-FEM mesh technique for fast analysis of waveguide problems containing rotatable tuning elements
PublikacjaIn this paper a meshing technique for 3D Finite Element Method is presented. It allows for fast analysis and optimization of the waveguide structures, which contain rotatable tuning elements. In the proposed procedure a thin layer of varying cylindrical mesh buffer is introduced in order to reuse unchanged mesh and FEM matrices in the rest of the domain.
-
Optical emission spectroscopy of plasma generated by a waveguide-supplied microwave plasma source operated at 915MHz
PublikacjaIn this paper we present the results of an optical emission spectroscopic study of an atmospheric pressure microwave (915 MHz) nitrogen and nitrogen with carbon dioxide (1%) plasma at high working gas flow rate. This study was aimed at determining rotational Trot and vibrational Tvib temperatures of N+2 ions and N2, CN molecules. The plasma was generated in a waveguide-supplied cavity-resonant type microwave plasma source. All...
-
Inline Waveguide Filter With Transmission Zeros Using a Modified-T-Shaped-Post Coupling Inverter
PublikacjaThis letter reports the design techniques for a class 2 of inline waveguide bandpass filters with sharp-rejection capabil3 ities at the lower stopband based on a novel nonlinear-frequency4 variant-coupling (NFVC) structure. The proposed NFVC consists 5 of a modified-T-shaped metallic post (MTP) that is placed at the 6 center of the waveguide broad wall with its open arms lying 7 along the waveguide width. The engineered NFVC structure 8...
-
Low-Loss 3D-Printed Waveguide Filters Based on Deformed Dual-Mode Cavity Resonators
PublikacjaThis paper introduces a new type of waveguide filter with smooth profile, based on specially designed dual-mode (DM) cavity resonators. The DM cavity design is achieved by applying a shape deformation scheme. The coupling between the two orthogonal cavity modes is implemented by breaking the symmetry of the structure, thus eliminating the need for additional coupling elements. The modes operating in the cavity are carefully analyzed...
-
Compact Quasi-Elliptic-Type Inline Waveguide Bandpass Filters With Nonlinear Frequency-Variant Couplings
PublikacjaThis work presents the design techniques to synthesize a class of compact inline quasi-elliptic-type waveguide cavity bandpass filters based on novel nonlinear frequency-variant couplings (NFVCs). These highly dispersive frequency-variant couplings (FVCs) are realized by means of a pair of partial-height posts that are placed at the junctions between every two cavity resonators. Each NFVC produces a transmission pole in between...
-
Influence of electrode geometric arrangement on the operation of narrow circular electrostatic precipitator
PublikacjaIn this work the influence of electrode geometric arrangement on the operation of a circular electrostatic precipitator (ESP) was investigated using Particle Image Velocimetry (PIV) method. The ESP was a glass circular cylinder (29 mm in diameter, 300 mm long) equipped with a wire discharge electrode and circular-cylinder collecting electrode. The stainless-steel discharge wire electrode (0.23 mm in diameter, 100 mm long) was mounted...
-
RADIATION OF HIGH INTENSITY SOUND BY CIRCULAR DISC BY MEANS OF THE NUMERICAL METHOD
PublikacjaThe main goal of this paper is to find sound pressure distribution radiated by the circular piezoelectric disc that vibrates with the finite amplitude. There has been presented the pressure distribution close to the radiating surface. Also it is shown the sound pressure distribution in the 3D form. The mathematic modeling was carried out on the base of the nonlinear acoustic equation with the proper boundary condition. The axial...
-
The Effect of Circular Saw Blade Clamping Diameter on its Resonant Frequencies
PublikacjaIn this paper results of comparison of characteristic resonant frequencies of circular saw blades as a function of the saw clamping diameter from the impact test are presented. Obtained results revealed that proportionally with the increase of the saw clamping diameter also the dynamical stiffness of the saw blade increased. As a consequence of that the resonant frequencies of the saw blade move to higher values. Moreover, with...
-
The effect of the spindle system on the position of circular saw teeth - a static approach
PublikacjaW pracy przedstawiono analizę powstawania błędów położenia ostrzy piły tarczowej w stosunku do przedmiotu obrabianego. błędy te pochodzą głównie z układu wrzeciona. Wyznaczono błędy położenia ostrzy dla klasycznego rozwiązania układu wrzeciona oraz dla nowego rozwiązania konstrukcyjnego proponowanego przez autorów.
-
Boundary Value Problems for Half-Plane, Strip and Rectangle with Circular Inclusions
Publikacja -
Circular Fashion – Consumers’ Attitudes in Cross-National Study: Poland and Canada
Publikacja -
The effect of improved cutting conditions of the circular saw blade on precision of cutting
PublikacjaW pracy przedstawiono analizę i wyniki badań doświadczalnych dokładności przecinania na dwuwrzecionowej pilarce tarczowej. W warunkach przemysłowych badano piły starej (typ "Multix") i nowej konstrukcji podczas przecinania pryzm ze zmrożonego drewna brzozowego. Ponadto, określono wpływ kinematyki układu przecinania na uzyskiwaną dokładność przecinania.
-
Experimental investigations of natural convection from circular plates at variable inclination
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych oraz bezwymiarową korelację liczb kryterialnych dla konwekcyjnej wymiany ciepła od izotermicznej płyty kołowej skierowanej ku górze dla różnych kątów pochylenia (od poziomej do pionowej) w szerokim zakresie wartości liczb Rayleigha. Badania przeprowadzono w wodzie dla płyty kołowej o średnicy 0,07 m. Celem pracy było określenie wpływu kąta pochylenia płyty na wartość liczby Nusselta.
-
Transportation of chips in the machining zone during cutting wood with circular saw
PublikacjaW pracy przedstawiono analizę odprowadznia wiórów ze strefy skrawania na zewnątrz materiału obrabianego przy przecinaniu drewna piłą tarczową.
-
The effect of circular saw blade clamping diameter on its resonant frequencies
PublikacjaIn this paper results of comparison of characteristic resonant frequencies of circular saw blades as a function of saw clamping diameter from the impact test are presented. Obtained results revealed that proportionally with the increase of the saw clamping diameter also the dynamical stiffness of the saw blade increased. As a consequence of that the resonant frequencies of the saw blade move to higher values. Moreover, with the...
-
Analyses of static displacements of a spindle apllied in typical circular sawing machines
PublikacjaW pracy przedstawiono analizę właściwości statycznych wrzeciona stosowanego w typowych pilarkach tarczowych. Zdefiniowano umowną oś obrotu wrzeciona pilarki tarczowej, która odpowiada geometrycznemu środkowi otworu piły tarczowej. W obliczeniach wyznaczono przemieszczenia umownej osi obrotu wrzeciona, wskaźnik sztywności wrzeciona oraz przemieszczenie poprzeczne piły.
-
Analysing By-Products Interaction as an Industry Resource of Circular Economy in Ukraine and the World
PublikacjaThe paper analyses existing and current scientific developments and literature sources, which show the advantages and disadvantages of many different influences of waste in Ukraine and other countries of Europe and the world. As a research result, stable connections have been established between the factors and criteria in assessing the by-product interaction as an industry resource. In our research, we used programs R.Studio and...
-
Introduction to smart solutions for wastewater: Road-mapping the transition to circular economy
PublikacjaToday there is an urgent need to move from a linear to a circular economy approach with special focus to water and environment. Despite the paramount importance, this transition is hampered by barriers which concern not only technological but embrace also organizational, regulatory, social, and economic aspects. In order to overcome such barriers, innovative water-smart solutions are needed and a robust roadmap for the transition...
-
Experimental examination and modification of chip suction system in circular sawing machine
PublikacjaThe article presents the results of experimental examination of the wood chip suction system in the existing sliding table saw before and after its modifi cation. The studies focused on the extraction hood of the mentioned system. The methodical experimental research of the pressure distribution inside the hood during wood chip removal for the selected rotational speed of saw blades of 3500 and 6000 min-1 with a diameter of 300...
-
Full scattering profile of circular optical phantoms mimicking biological tissue
PublikacjaHuman tissue is one of the most complex optical media since it is turbid and nonhomogeneous. In our poster, we suggest a new type of skin phantom and an optical method for sensing physiological tissue condition, basing on the collection of the ejected light at all exit angles, to receive the full scattering profile. Conducted experiments were carried out on an unique set-up for noninvasive encircled measurement. Set-up consisted...
-
Prevention of resonance oscillations in gear mechanisms using non-circular gears
PublikacjaOne of the main disadvantages of gear mechanisms is the occurrence of noise and vibrations. This study investigated the applicability of non-circular gears for preventing resonance oscillations in gear mechanisms. The influence of a small deviation of the gear centrodes from the nominal circles on kinematic and oscillatory characteristics was analysed. It was shown that a larger deviation results in a smaller resonance amplitude...
-
Comparison of natural frequencies of a circular saw blade obtained empirically and with FEM
PublikacjaThe knowledge of the natural frequencies’ values of circular saw blades is necessary to determine the minimal critical rotational speed in which they can work with required stability. Moreover, testing the circular saw blades with more complicated shapes, e.g. which have additional holes inside blades for cleaning knifes or additional indirect teeth in gullets, reveals some kind of problematic properties of these saw blades. The...
-
Fast surrogate-assisted frequency scaling of planar antennas with circular polarisation
PublikacjaIn this work, the problem of computationally efficient frequency scaling (re-design) of circular polarisation antennas is addressed using surrogate-assisted techniques. The task is challenging and requires the identification of the optimum geometry parameters to enable the operation of the re-designed structure at a selected (required) centre frequency. This involves handling several performance figures such as the antenna gain,...
-
Cut layer of a circular saw with radiaj run-out of cutting edges
PublikacjaW pracy przedstawiono analizę wpływu bicia promieniowego ostrzy piły tarczowej na zmianę nominalnego i całkowitego pola przekroju warstwy skrawanej.
-
A Trisection Filter Design With Negative Slope of Frequency-Dependent Crosscoupling Implemented in Substrate Integrated Waveguide (SIW)
PublikacjaThis letter reports on a novel realization of a microwave bandpass filter in a triplet configuration with a frequency-dependent crosscoupling implemented in substrate integrated waveguide (SIW). The design involves implementing dispersive coupling with a negative slope, a feature that allows the capabilities of the classic triplet topology to be extended. In this particular case, the implementation of two transmission zeros on...
-
Coupled-Resonator Waveguide Filter in Quadruplet Topology With Frequency-Dependent Coupling - A Design Based on Coupling Matrix
PublikacjaThis letter presents an application of a recently developed coupling matrix synthesis technique to design of coupled-resonator filters with dispersive inter-resonator couplings. This technique is used to design a novel coupled-cavity bandpass filter. Measurements validate the design and confirm effectiveness of the synthesis method. The filter is a four-pole generalized Chebyshev filter with three transmission zeros. Resonators...
-
A new class of eigenfunction expansion methods for fast frequency-domain analysis of waveguides
PublikacjaZaprezentowano nową technikę szybkiego obliczania charakterystyk dyspersyjnych falowodów z niejednorodnym wypełnieniem. Metoda ta oblicza przybliżone wartości stałej propagacji dla wymaganej częstotliwości, bazując na bardziej dokładnych wyliczeniach rozkładu pola i stałej propagacji dla kilku wybranych punktów częstotliwości.
-
[Chapter III] Influence of chip transport method on effects of cutting with circular saw
PublikacjaW pracy przedstawiono analizę transportu wiórów ze strefy skrawania na zewnątrz materiału obrabianego w procesie przecinania drewna piłami tarczowymi. Przedstawiono również przykłady zużycia pił tarczowych spowodowanych niewłaściwym transportem wiórów.
-
Directions and Challenges in the Management of Municipal Sewage Sludge in Poland in the Context of the Circular Economy
Publikacja -
Chirality sensing of bioactive compounds with amino alcohol unit via circular dichroism
Publikacja -
Symmetry-Dependent Vibrational Circular Dichroism Enhancement in Co(II) Salicylaldiminato Complexes
Publikacja -
Stereochemical Assingment of β -lactam Antibiotics and their Analogues by Electronic Circular Dichroism Spectroscopy
Publikacja -
Complementarity of electronic and vibrational circular dichroism based on stereochemical studies of vic-diols
Publikacja