Publications
Filters
total: 733
Catalog Publications
-
Influence of Phase Composition on Dielectric Properties of Bismuth-Based Ceramics with Scheelite-Type Structure
PublicationGoal of the present research was to study dielectric properties of BiNbO4 ceramics fabricated by solid state reaction route followed with pressureless sintering. The samples were fabricated from the mixture of oxides, viz. Nb2O5 and Bi2O3. Apart from stoichiometric amount an excess of 3%, 5% and 10% by mole of Bi2O3 was used. It was found that an excess amount of Bi2O3 oxide caused formation of Bi5Nb3O15 minor phase in amount of...
-
Determination of moisture resistance of covered electrodes according to PN-EN ISO 14372
PublicationMoisture present in the electrode covering is one of the sources of diffusible hydrogen in welded joints. In order to study the diffusible hydrogen content in deposited metal, a stand for moisturizing covered electrodes, in accordance with the PN-EN ISO 14372 standard, was built. After the stand was completed, a test of moisturizing the electrodes was carried out and measurements of the diffusible hydrogen content in deposited...
-
A New Microwave Ceramic – Polymer Composite with 0-3 Connectivity
PublicationGoal of the present research was to fabricate and study two-phase BiNbO4//PVDF composites with 0-3 connectivity. Such composite consists of there-dimensionally connected polymer matrix loaded with dielectric ceramic particles. In the present case BiNbO4 powder acted as an active phase (dispersed phase) whereas polyvinylidene fluoride (PVDF) acted as a non-active (passive) phase (matrix). BiNbO4//PVDF composites with the volume...
-
Quality increase for single-welded joints of thin-walled structures by means of simulation modelling
PublicationThe Simulation calculation module and the SolidWorks software package have helped to define the optimal shape and dimensions of single-welded joints which may serve the basis for calculating the process parameters of welding. Having compared the models with different weld cross-sections the authors have defined that the weld height and width do not significantly affect the stress concentration, and the stress concentration and...
-
INFLUENCE OF CERAMIC COATING ON MECHANICAL PROPERTIES OF STAINLESS STEEL
PublicationCrystal structure and phase composition of stainless steel substrates (AISI 304 type) was studied and it was found that they adopted the cubic symmetry. The calculated elementary cell parameter for the mayor Fe-Ni phase (weight fraction 99%) was a = 3.593 Å, whereas the mean grain size was = 2932 Å. Morphology of the stainless steel substrate surface was studied with profilometry. Mechanical properties of the stainless steel...
-
X-RAY DIFFRACTION STUDY OF BISMUTH LAYER-STRUCTURED MULTIFERROIC CERAMICS
PublicationGoal of the present research was to apply a solid state reaction route to fabricate bismuth layer-structured multiferroic ceramics described with the formula Bi5FeTi3O15 and reveal the influence of processing conditions on its crystal structure and phase composition. Simple oxide powders Bi2O3, TiO2 and Fe2O3 were used to fabricate Aurivillius-type bismuth layer-structured ferroelectrics. Pressureless sintering in ambient air was...
-
Poroelastic Material for Urban Roads Wearing Courses
PublicationConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
Porous materials used as inserted bone implants
PublicationArtykul zawiera przegladowa analize literatury dotyczaca scaffoldow
-
On degradation of glass/polyester laminate immersed in water
PublicationMechanical behaviour was compared for glass/ polyester laminates manufactured in the boatbuilding plant using three methods: hand lay-up, vacuum bagging, infusion. Specimens were tested in dry condition and following accelerated water immersion test (70°C- corresponding to the exposure of 30 years at 19°C). In three point bending test 40-50% reduction in laminate strength was observed due to water immersion. The highest degradation...
-
Evaluation of Wear Resistance of Ti alloys used for elements friction of knee endoprosthesis
PublicationThe paper presents research results of resistance to abrasive wear of titanium alloys: Ti6Al4V (commonly used) and Til3Nb13Zr (alloy of new generation) in association with polyethylene (UHMW-PE) predisposed for elements on pair of the knee endoprosthesis. The results were analysed from the point of possibility of an use of new generation titanium alloys as components of such implants. The tests of resistance to abrasive wear of...
-
Diffusible hydrogen content in deposited metal of multilayer welded joints
PublicationThe article describes manufacturing technology of multilayer joints in terms of control the diffusible hydrogen content. Diffusible hydrogen content in deposited metal for multilayer welded joints made of covered rutile electrodes or covered cellulosic and basic electrodes was determined. It was found that after four beads, the diffusible hydrogen content decreases in the case of the first technology from 36 ml/100 g to 18 ml/100...
-
Preliminary studies of seamless flux cored wires stored in extreme conditions
PublicationIn the paper preliminary experimental studies of flux cored wires moisturized under controlled conditions are described. Three seamless wires of different grades have been placed in environmental chamber and moisturized in extremely adverse conditions (temperature T = 60° C, relative humidity H = 90%) for 240 hours. During this time measurements of weight gain and observations of surface of wires have been carried out. Also diffusible...
-
Comparative in vitro research of the Human Aortic Bioprosthesis
PublicationE valuate of the usefulness and reliability of structures based on the analysis of recorded parameters determining the flow through the Human Aortic Bioprosthesis (HAB) have been dealt with. By flow parameters changes determining the performance environment of prosthesis analyzed change of the motion dynamics of the valve leaflets as a function of pressure, thereby determining the degree of alignment of the prosthesis to the performance...
-
The influence of biological environment on the appearance of silver-coated implants
PublicationDespite antibiotics preventive treatment before and after implantation, risk of infection is real. The infections at the implant surface developein a few months after applying them into the body. To prevent the development of bacteria and to reduce the risk of infection, implants coated with silver layer come into use. The paper presents the research results in biological environment on vein and orthopaedicimplants covered with...
-
Influence of dopants on structure of polycrystalline bismuth niobate
PublicationBismuth niobate (BiNbO4) has attracted attention as a low-fired ceramics with promising microwave application potential. BiNbO4 ceramics was fabricated by mixed oxide method and sintered at temperature T<1000˚C. As the sintering aids a small amount of CuO oxide was used. The crystalline structure of the ceramic samples was examined by X-ray diffraction method at room temperature. The Rietveld refinement method was used for analysis...
-
Effect of Linear Energy and Microstructure on the Content of Residual Hydrogen in Welded Joints made of Superduplex Steels
PublicationThe article presents tests concerning the content of retained hydrogen present in FCAW and SAW welded joints made of superduplex steel. The use of various welding technologies resulted in the obtainment of welds having different microstructures and ferrite contents. Measurements of retained hydrogen present in joints (performed using the complete combustion method) revealed various contents of hydrogen in the base material and...
-
The Effect of Long Term Service at Elevated Temperatures on Microstructure Degradation of Austenitic Reformer Tubes
PublicationThe paper analyses the relationship between an increase of the inner diameter of tubes made of Manaurite XM cast steel and transformations occurring in their microstructure due to long-lasting operation in methane reformer. Examinations included metallographic analysis with light microscope (LM), scanning electron microscope (SEM) and microanalysis of the chemical composition of precipitates (EDX). It was indicated that there is...
-
Influence of parameters of deep grinding on nanohardness and surface roughness of C45 steel
PublicationPrzedstawiono wyniki badań wpływu głębokości współbieżnego szlifowania powierzchni płaskich na chropowatość i nanotwardość warstwy wierzchniej stali C45 o strukturze ferrytyczno-perlitycznej i średniej wielkości ziarna 20 μm. Dla wszystkich wartości głębokości szlifowania uzyskano znaczny wzrost twardości warstwy wierzchniej przedmiotu obrabianego.
-
Effect of the Post-Weld Surface Condition on the Corrosion Resistance of Austenitic Stainless Steel AISI 304
PublicationSurfaces of welded elements made of corrosion-resistant (stainless) steels develop temper colours. The removal of thickened oxide layers off steels exposed to temperatures below 300°C is necessary and entails the restoring of high corrosion resistance of the stainless steel. The article presents tests concerned with the effect of a method applied to remove post-weld temper on the corrosion resistance of austenitic stainless steel...
-
Badania spawalności stali S460N w środowisku wodnym z wykorzystaniem próby Tekken
PublicationSpawanie w środowisku wodnym niesie ze sobą wiele problemów, wśród których najważniejszym jest skłonność stali do powstawania pęknięć zimnych. O ile w przypadku spawania na powietrzu istnieje wiele metod zapobiegania tym pęknięciom, o tyle pod wodą zastosowanie tych metod jest ograniczone. Z tego powodu konieczne jest określenie skłonności danego materiału do pękania zimnego. W pracy oceniono spawalność drobnoziarnistej...
-
Powikłania po rekonstrukcji piersi: problem zakażeń i strategii prewencyjnej - przegląd literaturowy
PublicationW niniejszej pracy przedstawiono dane dotyczące powikłań po rekonstrukcji piersi. Manuskrypt ma na celu usystematyzowanie wyników badań z ostatnich lat wraz z aspektami, takimi jak: częstotliwość występowania powikłań oraz ich rodzaj, czynniki predysponujące, a także możliwości profilaktyki. Przeanalizowano dane literaturowe z ogólnie dostępnych artykułów z okresu ostatnich pięciu lat, ze szczególnym uwzględnieniem zakażeń. Do...
-
Możliwości sterowania ilością wodoru dyfundującego w złączach spawanych
PublicationW pracy omówiono metalurgiczne i technologiczne czynniki wpływające na obecność wodoru dyfundującego w stopiwie uzyskanym w środowisku powietrznym i pod wodą oraz podano metody obniżania jego ilości. Przedstawiono wyniki badań ukierunkowanych na określenie wpływu warunków i parametrów spawania na nawodorowanie stopiwa. Opracowano i podano zależności umożliwiające prognozowanie zawartości wodoru w złączach wykonanych pod wodą...
-
Modelling of dielectric properties of BiNbO4-based microwave ceramics
PublicationIn the present paper results of the studies devoted to computer simulations of dielectric response of electroceramics in a frequency domain as well as analysis of the experimental data are given. As an object of investigations BiNbO4-based microwave ceramics was taken. Simulations of the hypothetical impedance response of the ceramic system were performed under assumption of the brick-layer model. A strategy for analysis and modelling...
-
Badania własności mechanicznych próbek płaskich z rur kwadratowych ze stali S355.
PublicationCelem pracy było: - zbadanie własności mechanicznych za pomocą próby statycznego rozciągania, próbek wyciętych wzdłuż kierunku walcowania z rur kwadratowych dostarczonych przez firmę Borg. Na podstawie analizy certyfikatów materiałowych rur, z których wykonywano konstrukcje spawane, zaistniała wątpliwość co do ich rzetelności w zakresie własności mechanicznych ocenianych na podstawie próby rozciągania. Ściślej rzecz biorąc chodziło...
-
O możliwości spawania elementów kształtowych giętych na zimno ze stali typu S355
PublicationCelem pracy jest ocena wpływu gięcia na zimno profili na własności spoin usytuowanych w rejonie gięcia. Praca obejmuje opis tych zagadnień z punktu widzenia budowy strukturalnej i warunków sprzyjających procesowi starzenia jak i technologii spawania w odniesieniu do stali S355. Własności mechaniczne elementów giętych na zimno są niehomogeniczne wzdłuż obwodu z powodu różnic w umocnieniu powstającego w trakcie gięcia na zimno. w...
-
Opracowanie opinii na temat własności materiału podstawowego oraz jakości spoin kotła typu KSBS 380 nr fabryczny 117
PublicationNiniejsza opinia przedstawia odpowiedzi na pytania Sądu wyrażone w w/w postanowieniu, a mianowicie czy zastosowane materiały do produkcji przedmiotowego kotła jak również jakość spoin była przyczyną awarii kotła w dniu 25.12.2014r, w tym również porównanie uzyskanych wyników badań z dokumentacją konstrukcyjna kotła.2. Połączenia spawane w badanej konstrukcji kotła były najsłabszym elementem konstrukcyjnym, w którym na skutek...
-
Biological and mechanical properties of bone cement with nanoarticles - in vitro and in vivo research
PublicationDespite antibiotic preventive treatment both before and after implant implementation, the risks of infection are real. These infections develop at the implant surface a few months after inserting them into the body. To prevent the development of bacteria and reduce the risk of infection, implants coated with nanoparticles are used. The Mechanical Department of the Technical University of Gdansk carries out research into using bone...
-
Opracowanie procedury i badania wytrzymałościowe połączeń spawanych pomiędzy rurą kwadratowa a elementami giętymi na zimno ze stali S355 oraz testowanie połączeń o grubości 4, 6, 8mm typu S355
PublicationCelem pracy było: - opracowanie procedury badania wytrzymałości połączeń spawanych rozciąganych w kierunku prostopadłym i w kierunku równoległym (ścinanych) do osi spoiny. Spoiny te łączyły elementy rur kwadratowych o różnej grubości z elementami w kształcie ceownika giętymi na zimno. - wykonanie próbek do badań wytrzymałościowych wyciętych z elementów spawanych dostarczonych przez Zakład Produkcyjny firmy Borga obciążonych prostopadle...
-
Badania stanu technicznego ścianek szczelnych strony południowej i północnej komory południowej śluzy Dzierżno
PublicationPrace dotyczyły badań nieniszczących łączników (zamków) Paine`a oraz ścianek szczelnych. Ściany boczne komory południowej śluzy Dzierżno zbudowane są ze stalowych pasów blachy o grubości około 16mm i długości 22m połączonych ze sobą wzdłuż dłuższej krawędzi za pomocą zamków Peine`a. System ten umożliwia uzyskanie szczelnego połączenia na całej długości ścianki. Zaawansowany proces korozji spowodował rozszczelnienie połączenia...
-
COLLABORATIVE LEARNING ENVIRONMENT FOR ENGINEERING EDUCATION (COLED)
PublicationCollaborative Learning Environment for Engineering Education is a European project implemented under the Erasmus + program, The main goal of 5 partners from 4 different European countries – Bulgaria, Poland, Portugal and Romania is to develop an innovative collaborative training approach, encompassing curricula related to the introduction of enterprise automation. Project activities are carried out in the period from Dctober 2018...
-
KOMPUTER W LABORATORIUM VS LABORATORIUM W KOMPUTERZE
PublicationAbstract. In March 2020, all of the sudden, university teachers have been made to run all the classes remotely. But, how to deal with lab classes for future engineers? Different aspects of teaching labs on Moodle, that should be taken in consideration, are not only connected with the content of the class, but also with transferring the knowledge and materials to the students in a way that would avoid distractions and help students...
-
Opracowanie ekspertyzy dotyczącej przyczyn pękania łopatek wirnika SP turbiny PG1 typu 13UP55
PublicationZakres badań i analiz dotyczył ustalenia przyczyn pękania elementów łopatek wirnika SPA5 turbiny TG1 typu 13UP55 obejmował: 1. wykonanie badań składu chemicznego stali, z której wykonano łopatki dostarczone przez Zleceniodawcę dwoma metodami, 2. badania mikroobszarów zniszczenia łopatek na mikroskopie elektronowym skaningowym z mikroanalizatorem EDS, 3. badania metalograficzne makroskopowe i mikroskopowe fragmentów...
-
Using Moodle as a Solution to Interdisciplinary E-collaboration Issues
PublicationRapid technological development in recent years has contributed to numerous changes in many areas of life, including education and communication. Establishing interdisciplinary collaboration brings many benefits, however, it is often associated with numerous problems and inconveniences, as well as the need of constant improvement, lifelong learning, professional development (CPD) and finding an effective way of information transferring....
-
Charakterystyka procesu utleniania stopów cyrkonu i jego wpływu na stan warstwy wierzchniej oraz desorpcję wodoru
PublicationZjawiska degradacji tlenowej i wodorowej stopów cyrkonu mają istotne znaczenie dla modelowania mechanizmów utraty spójności koszulek paliwowych w warunkach katastrof nuklearnych, szczególnie typu LOCA. Celem naukowym pracy było poznanie i analiza zachowania utlenionych, komercyjnych stopów cyrkonu, wpływu wodoru na utlenione stopy oraz przedstawienie fizycznych źródeł i matematycznych zależności pomiędzy tymi zjawiskami. Wyniki...
-
Low noise poroelastic road pavements based on modified asphalt binder
PublicationTire/road noise is one of the most important environmental problems related to road traffic. As the most effective way to fight noise is reduction of sound emission from the source, a lot of work is being done to improve tire and road surfaces construction. This paper describes the first “road” results obtained within the SEPOR project, which is focused on developing a low noise poroelastic road surface based on bituminous binder....
-
Nanoindentation tests titanium alloy Ti-6Al-4V after interference laser treatment
PublicationThe study aimed was to assess selected mechanical properties of surface layers obtained after interference laser treatment – DLIL of titanium alloy Ti-6Al-4V used for implants. The samples were melted in still air at room temperature, for this purpose Nd:YAG laser was used, the number of laser shots was variable. Next, nanoindentation tests were performed, based on which Young’s modulus and nanohardness in the obtained surface...
-
Wpływ intensywności prędkości uderzenia na niszczenie cząstkami stałymi w środowisku wodnym stali X10CrAlSi18
PublicationErozja cząstkami stałymi w środowisku wodnym jest złożonym zjawiskiem ze względu na jednoczesne oddziaływanie wielu czynników, takich jak prędkość i kąt uderzenia, koncentracja cząstek, własności materiału i cząstek stałych, prowadząc do efektu synergicznego. Zmiana jakiegokolwiek parametru procesu erozyjnego prowadzi do zmiany szybkości erozji. Z tego względu istotne jest badanie wpływu poszczególnych czynników na proces niszczenia....
-
Low Noise Poroelastic Road Pavements Based On Bituminous Binder
PublicationTire/road noise is the dominant source of traffic noise. It depends both on the tire design and on the characteristics of road pavements as well as on the vehicles’ operating conditions. Due to the fact that conventional (pneumatic) car tires have almost reached the limits of their ability to further reduce their noisiness, it is widely believed that the additional reduction of tire noise will be possible mainly through modifications...
-
Erozja Kawitacyjna Austenitycznej Stali Nierdzewnej 1.4541
PublicationProces erozji kawitacyjnej powoduje niszczenie materiału, na który składają się: odkształcenie plastyczne, ubytki masy, zmiany fazowe, fragmentacja ziaren, zmiany mikrogeometrii i makrogeometrii powierzchni. Różnorodność czynników mająca wpływ na proces niszczenia materiału sprawia, iż trudno jest przewidzieć postęp procesu niszczenia ciała stałego wskutek kawitacji. Z tego względu...
-
Wpływ metody trawienia i spiekania na właściwości mechaniczne powłok z nanorurek węglowych osadzonych elektroforetycznie na podłożu Ti13Nb13Zr
PublicationDo eksperymentu użyto stopu tytanu Ti13Zr13Nb, który ze względu na swój skład chemiczny i właściwości mechaniczne stanowi doskonały materiał do zastosowań w inżynierii medycznej. Celem pracy była ocena wpływu przygotowania podłoża (rodzaj zastosowanego odczynnika trawiącego) oraz obróbki końcowej (proces spiekania) powłok z wielościennych nanorurek węglowych na ich właściwości mechaniczne (nanotwardość, moduł Younga). Do wytworzenia...
-
Qualification of brazing procedure for furnace brazing of austenitic steel according to requirements of the ASME BPVC section IX
PublicationThe article presents the procedure for qualifying brazing technology in a vacuum furnace on the example of stainless steel elements joined with copper filler material from the F-No group. 105, in accordance with the ASME Sec. IX, part QB (ASME Boiler and Pressure Vessel Code. Qualification Standard for Welding, Brazing and Fusing; Procedures; Welders; Brazers; and Welding, Brazing and Fusing Operators). The essential variables...
-
CHALK & TALK OR SWIPE & SKYPE?
PublicationTechnology in classroom is a matter of heated discussions in the field of education development, especially when multidisciplinary education goes along with language skills. Engineers’ education requires theoretical and practical knowledge. Moreover, dedicated computer skills become crucial for both young graduates and experienced educators on the labor market. Teaching online with or without using different Learning Management...
-
Projekt aCiret odpowiedzią na wyzwania przemysłu 4.0
PublicationDruga dekada XXI w. jest początkiem nowej rewolucji przemysłowej, określanej jako przemysł 4.0. Coraz powszechniejsze systemy cyberfizyczne, internet rzeczy, obliczenia i procesy sterowane w chmurze wymagają wysoko wykwalifikowanych pracowników, uzbrojonych w ogólną i specjalistyczną wiedzę oraz doświadczenie, wykazujących się przedsiębiorczością i inicjatywą. Problem braku odpowiedniej kadry dotyka firmy z sektora przemysłowego,...
-
Kwalifikowanie technologii lutowania twardego próżniowego stali austenitycznej zgodnie z wymaganiami przepisów ASME BPVC, sekcja IX
PublicationW artykule przedstawiono procedurę kwalifikowania technologii lutowania twardego w piecu próżniowym na przykładzie elementów ze stali wysokostopowej nierdzewnej austenitycznej łączonych lutem miedzianym z grupy F-No. 105, zgodnie z przepisami ASME Sec. IX, part QB (ASME Boiler and Pressure Vessel Code. Qualification Standard for Welding, Brazing and Fusing; Procedures; Welders; Brazers; and Welding, Brazing and Fusing Operators)....
-
Fabrication methods of smart composite coatings - review
PublicationPostoperative bacterial infections are one of the main reasons for unsuccessful implantation of long-term implants. The development of bacterial infection requires antibiotic therapy, in extreme cases a reimplantation procedure is necessary. In order to provide materials for implants with antibacterial properties, they are subjected to modifications to create a coating that will release the drug substance, when the inflammation...
-
Fabrication of La-Doped Bi4Ti3O12 Ceramics
PublicationLa-modified Bi4Ti3O12 is a typical ferroelectric, piezoelectric and electro-optic material, having relatively low coercive field, low dielectric constant, high Curie temperature and high breakdown strength. Goal of the present research was to apply mixed oxide method for fabrication of BiTLax ceramics, study its chemical composition, crystalline structure and microstructure. The compound BiTLax for x=0, 0.25, 0.5, 0.75 ceramic...
-
Dielectric Properties of BiNbO<sub>4</sub>-Based Ceramic-Polymer Composites with 0-3 Connectivity
PublicationIn the present study two-phase BiNbO4//PVDF composites with 0-3 connectivity were studied by impedance spectroscopy within the frequency range Δν=100Hz-1MHz at room temperature. Polyvinylidene fluoride (PVDF) acted as a matrix whereas bismuth niobate (BiNbO4) powder acted as a dispersed phase. The volume fraction of the ceramic phase was cV=2, 4, 6, 8, 10, 16 and 20vol%. Analysis of the impedance data registered for composites...
-
Effects of V2O5 Additive on Structure and Dielectric Properties of BiNbO4 Ceramics
PublicationGoal of the present research was to investigate the influence of V2O5 additive on the structure and dielectric properties of BiNbO4 ceramics. To fabricate BiNbO4 ceramics with V2O5 added the solid state reaction route and pressureless sintering was utilized. Thus obtained ceramics was characterized in terms of its microstructure (SEM), chemical composition (EDS), phase composition and crystalline structure (X-ray phase and structural...
-
Badania nieniszczące jakości spoin szyn poddźwigowych na nabrzeżu przeładunkowym T1 w DCT w Porcie Północnym
PublicationCelem podstawowym niniejszego opracowania było sprawdzenie za pomocą NDT jakości spoin wykonanych w ramach prac naprawczych w DCT w roku 2017 (styki szyn poddźwigowych typu A120 na nabrzeżu T1 w DCT Port Północny Gdańsk). W ramach opracowania: 1) Ustalono zakres badań - na podstawie potrzeb Kierownictwa Infrastrukury DCT; b) Analizowano wyniki badań nieniszczących wykonanych w sierpniu 2017r.;...
-
STUDY OF CuO AND V2O5 EFFECT ON IR SPECTRA OF POLYCRYSTALLINE BISMUTH NIOBATE
PublicationBismuth niobate (BiNbO4) ceramics were fabricated by mixed oxide method and sintered by presureless sintering method. BiNbO4 ceramics doped with V2O5 additive in amount 0.125 wt%, 0.250 wt% and 1 wt% of was sintered at T = 910°C whereas BiNbO4 ceramics doped with 2 wt% of CuO additive was sintered at T = 890°C and T = 910°C. It was found that V2O5 additive improved morphology of the ceramic samples. However, the chemical composition...
-
COMPOSITE MATERIAL SELECTION FOR A PATIENT TRANSFER ASSIST DEVICE
PublicationLaminates - layered composites containing at least two elements (matrix and reinforcement) widely used in industry have also found their usage in medicine. Their main feature is the ability to modify the material in order to obtain the required properties. Depending on the needs, we can modify reinforcement, type of resin or the method of bonding substrates. Commonly used fibers are: carbon fiber, glass and aramid fibers; resins...
-
X-Ray Computer Tomography Study of Degradation of the Zircaloy-2 Tubes Oxidized at High Temperatures
PublicationThe investigations of high-temperature oxidation of zirconium alloys, applied for fuel pellets in nuclear power plants, are usually limited to oxidation kinetics, phase transformations and microstructural characterization. The purpose of this research was to characterize the degradation phenomena occurring within oxide layer and at the interface oxide/metal, on internal and external Zircaloy-2 tube...
-
Wykorzystanie e-narzędzi w nauczaniu, egzaminacji i certyfikacji Autodesk
PublicationAutoryzowane Centrum Szkolenia Autodesk Politechniki Gdańskiej zostało założone w 1995 roku. Stanowiło odpowiedź na rosnące zainteresowanie zdobywaniem umiejętności obsługi oprogramowania typu CAD wśród studentów i młodych inżynierów. Rosnące zainteresowanie zaowocowało stopniowym wdrażaniem kolejnych narzędzi e-learningowych. Wraz ze zdobyciem statusu Autoryzowanego Akademickiego Partnera Autodesk w 2016 roku pojawiły się nowe...
-
Design and material selection for a patient transport device in field hospitals
PublicationACKGROUND: A major cause of patient and hospital worker injuries occurs transferring patients between two planes. The main aim of this paper was to propose a design of patient’s lift and transfer apparatus for use in field hospitals. The assumption was to design lightweight, durable and ergonomic device using innovative material. The authors concentrated on partial elimination of manual lifting in order to device could work both...
-
Wpływ czynników technologicznych na zawartość wodoru dyfundującego w stopiwie rutylowych drutów proszkowych
PublicationObecność wodoru dyfundującego jest jednym z warunków powstawania pęknięć zimnych oraz przyczynia się do występowania porowatości w złączach spawanych. W pracy podjęto próbę określenia istotności wpływu wybranych czynników technologicznych na zawartość wodoru dyfundującego w stopiwie co ma na celu umożliwienie prognozowania jego ilości przez zmiany wartości parametrów spawania. Analiza statystyczna wyników badań eksperymentalnych...
-
Analysis of Rolling Resistance of Tires With Run Flat Insert
PublicationRun flat properties are required for tires intended for special applications like military or rescue vehicles. Run-Flat inserts make possible to drive a car or truck, with certain restrictions, also when inflation pressure is very low or non-existing (after tire damage). Rolling resistance of tires rolling the inserts increases considerably in relation to the rolling resistance of properly inflated tires. This paper presents results...
-
Badanie wpływu budowy przestrzennej stopu NiTi na jego odporność kawitacyjną
PublicationReferat stanowi wprowadzenie teoretyczne do oceny możliwości dalszego zwiększania odporności kawitacyjnej stopów opartych na fazach międzymetalicznych. autor opisuje stan wiedzy, jaki można znaleźć w literaturze na temat sposobów zwiększania odporności kawitacyjnej materiałów. Zaprezentowano również własne spostrzeżenia i ich odniesienie do występujących w literaturze teorii. Podano prace, jakie są wykorzystywane w chwili obecnej...
-
Road texture influence on tire rolling resistance
PublicationTire rolling resistance is one of the most important resistive forces acting on road vehicles. It depends on tire and surface characteristics as well as vehicle operating parameters. This paper deals with the influence of road surface texture on rolling resistance of passenger car tires. Results of road measurements performed on variety of road surfaces are presented.
-
Tyre/road noise reduction of poroelastic road surface tested in a laboratory
PublicationA so-called poroelastic road surface (PERS) is being developed in Europe. This contains a large percentage of rubber particles mixed with hard aggregate (stone and sand) and bound with polyurethane. This gives high air void content (around 30 %), high elasticity and smooth texture, all of which should give low noise properties. Inthis experiment anominally 30 mm thick sample of PERS was mounted on a steel drum. Various car tyres...
-
IN VIVO DEGRADATION OF BIOMATERIALS
PublicationThe material designed to be introduced into the human tissue should be biocompatible and biofunctional. Unless it is so, the body may respond to the implant in different ways. An inflammation reaction may appear such as: parting of items of the implant surface resulting from fraction or pressure. The condition of the surface has an important influence on the usefulness of the implant. The required values depend on the implant function...
-
Analysis and Comparison of Safety of Children and Adult Passenger in Car Based on Crash Tests Results
PublicationMost important features of the child seat were presented. There was made analysis of selected dynamic loads acting on mannequins heads during a collision. Comparison of loads acting on the kid in a child seat and the other passengers in a car is presented. In analysis of the results particular attention has been paid on the children's secure in a car. The phenomena of collision child's occipital bone with seat backrest was described....
-
ZASTOSOWANIE ZGRZEWANIA WYBUCHOWEGO DO WYTWARZANIA KOMPOZYTÓW METALOWYCH O OSNOWIE ALUMINIOWEJ
PublicationEnergia wybuchu może zostać wykorzystana do realizacji wielu procesów technologicznych, m.in. wytwarzania złączy zgrzewanych, prasowania proszków, tłoczenia, odprężania i utwardzania metali. Bardzo interesującym zastosowaniem technologii zgrzewania wybuchowego jest wytwarzanie kompozytów metalowych. W artykule scharakteryzowano kompozyty metalowe i zgrzewanie wybuchowe jako jedną z metod ich otrzymywania. Przedstawiono autorską...
-
Skłonność do tworzenia pęknięć zimnych złączy ze stali S420G2+M spawanej pod wodą metodą mokrą
PublicationPrzeniesienie procesu spawania do środowiska wodnego skutkuje przede wszystkim zwiększeniem prędkości stygnięcia złącza oraz wzrostem zawartości wodoru dyfundującego w stopiwie. Środowisko wodne powoduje istotne pogorszenie spawalności stali jednak zastosowanie odpowiedniej technologii spawania pozwala na uzyskanie złączy o właściwościach zbliżonych do wykonywanych na powietrzu. W pracy oceniono przydatność drobnoziarnistej stali...
-
The research of glass-ceramics implants used for bone pitches to examine bacteria adhesion occuring in human body
PublicationThe paper deals with the research concerning the bacteria adhesion on bioactive glass - ceramics materials
-
WPŁYW CYKLU CIEPLNEGO NA WŁAŚCIWOŚCI ZGRZANYCH WYBUCHOWO ZŁĄCZY STAL-ALUMINIUM
PublicationW artykule omówiono budowę, własności oraz technologię wytwarzania trójwarstwowych łączników zgrzewanych wybuchowo typu stal–stop aluminium AlMg. W łącznikach tego typu występuje połączenie stali z aluminium, które decyduje o ich własnościach eksploatacyjnych. Szczególną uwagę zwrócono na proces spawania łączników, który może być przyczyną znaczącego spadku wytrzymałości złączy stal-aluminium. Przedstawiono wyniki badań właściwości...
-
Zastosowanie techniki ściegu odpuszczającego do spawania mokrego
PublicationW artykule przedstawiono zastosowanie techniki ściegu odpuszczającego do poprawy właściwości złączy ze stali konstrukcyjnych wykonywanych w warunkach mokrego spawania pod wodą. Scharakteryzowano spawanie mokre elektrodami otulonymi zmiany struktury i właściwości złączy spawanych przez nakładanie ściegów odpuszczających. Przedstawiono metodykę oraz wyniki badań metalograficznych i twardości próbek ze stali konstrukcyjnej o podwyższonej...
-
Wytwarzanie blach bimetalowych al 99,98 -m1e wstępnie łączonych metodą zgrzewania wybuchowego
PublicationW artykule omówiono proces wytwarzania blach bimetalowych AL99,8-M1E obejmujący etap łączenia warstw stanowiących wsad bimetalowy oraz etap związany z ich plastycznym kształtowaniem poprzez walcowanie. Przedstawiono i omówiono wpływ parametrów procesu walcowania na nierównomierność odkształcenia warstw stanowiących bimetal.
-
Degradation of metallic implants
PublicationPresence of metallic implants made of stainless steels, Co and Ti alloys is sometimes followed by some undesired allergic reactions and inflammatory processes and consequently the necessity of reimplantation.
-
Degradation of metal implants covered with silver
PublicationSilver was known for its antibacterial properties as long ago as in antiquity. The silver ions have ability to join the bacteria surface. Low density of silver ions Ag+ influence the protons through the bacteria surface, which results in total destruction of the cell. Antibacterial activity of silver remains in proportion with the density of silver ions Ag+ in the environment.
-
Analysis of Asymmetrical Rolling Process of Multilayer Plates
PublicationW niniejszej pracy przedstawiono wyniki badań numerycznych asymetrycznego procesu walcowania blach wielowarstwowych M1E-Al99,8-AlMg5. Modelowanie numeryczne procesu walcowania blach wielowarstwowych przeprowadzono w programie Forge 2D, którego obliczenia bazują na metodzie elementów skończonych. Przedstawione w pracy wyniki umożliwiły przeprowadzenie analizy procesu walcowania blach wielowarstwowych.
-
Properties of surface layers of titanium alloy Ti6Al4V after laser melting processes
PublicationThe article presents the investigation results of titanium alloy Ti6Al4V surface layer after laser melting process. The process of laser melting was performed using Nd-YAG laser. The evaluation of structure of the alloy as well as hardness and chemical composition was performed. It was shown that laser melting changes the structure and properties of titanium alloy Ti6Al4V and process parameters as scanning speed affects the thickness...
-
Badania ultradźwiękowe przyczepności warstwy brązu do podłoża stalowego wewnętrznych powierzchni tulei o średnicach Dn85mm i Dn96mm ( z kołnierzem o średnicy Dn107mm)
PublicationW opracowaniu przedstawiono wyniki ultradźwiękowych badań przyczepności brązu do tulei stalowych.
-
Określenie przyczyny uszkodzenia kolana rurociągu 3/4''-025-P79 na instalacji produkcji wodoru w Grupie Lotos SA
PublicationNiniejszą pracę wykonano na zlecenie Grupy Lotos SA, nr OK/78/2010 z dnia 01 lutego 2010 r. Celem pracy było ustalenie przyczyny uszkodzenia kolana rurociągu 3/4"-025-P79 gat. P22 ASTM SA-335 na instalacji produkcji wodoru 250 w Grupie Lotos SA. Wykazano, że główną przyczyną powstania pęknięcia była niewłaściwa technologia wykonania elementu, skutkująca obecnością ostrych karbów na powierzchni wewnętrznej i podwyższoną twardością...
-
Badania ultradźwiękowe przyczepności warstwy brązu do podłoża stalowego wewnętrznych powierzchni tulei o średnicach Dn70mm, Dn85mm i Dn96mm (z kołnierzem o średnicy Dn107mm)
PublicationW opracowaniu przedstawiono wyniki badań przyczepności brązu do powierzchni wewnętrznych tulei stalowych.
-
Ekspertyza materiałowa osłon palników generatorów gazów obojętnych
PublicationNa zlecenie firmy PIROMETAL z Gdańska wykonano badania materiałowe osłon palników generatorów gazów obojętnych. Wykonano analizy składu chemicznego 4 próbek pobranych z osłon palników, identyfikację zastosowanych materiałów.Przeprowadzono analizę przydatności zastosowanych stali na osłony palników oraz przedstawiono opinię nt. doboru materiału na osłony palnika w generatorach gazów obojętnych.
-
Influence of laser melting on surface layer properties of titanium alloy Ti6Al4V
PublicationIn time of rapid technology and medicine progress, implants are becoming more widely used in the human body, ranging from dental implants, stabilizing plates, screws, orthopaedic prostheses. For example, there are many types of hip prostheses used for hip replacement as well as various types of materials used for these orthopaedic prostheses. Properties of titanium alloys used in hip prostheses combined with good strength properties,...
-
Badania jakości spoin próbek wyciętych ze zbiornika - odgazowywacza termicznego zakładu produkcyjnego w Redzie. Grupa PREFABET S.A.
PublicationW opracowaniu przedstawiono wyniki badań nieniszczących, wytrzymałościowych i metalograficznych próbek złaczy spawanych wyciętych z odgazowywacza po awarii.
-
Przeprowadzenie ekspertyzy porównawczej radiogramów spoin
PublicationW opracowaniu przedstawiono wyniki badań porownawczych radiogramów wycenianych przez dwa ośrodki
-
Charakterystyka korozji typu pylenie metalu w rafineryjnej instalacji platformingu CCR
PublicationW artykule przedstawiono charakterystykę procesu pylenia metalu w stali 9Cr-1Mo eksploatowanej w piecach instalacji platformingu CCR. Wykazano, że mechanizm niszczenia stali nie zależy od czasu eksploatacji i od stopnia konwersji wsadu, a krótkotrwały wzrost stężenia związków siarki we wsadzie może zwiększyć szybkość tworzenia pyłu.
-
Assessment of fitness for service of Cr-Mo steel tubes in catalytic reforming charge heaters
PublicationIn this paper characteristic features of metal dusting corrosion in high temperature gas mixtures of high carbon activity in catalytic reforming units, including Continuous Catalyst Regeneration (CCR) platformer are presented. Examples of 2.25Cr-1Mo and 9Cr-1Mo steel tubes at advanced stages of metal dusting process after long-term service in charge heaters are used to prove that destructive examinations are necessary to provide...
-
Numeryczne modelowanie prędkości płynięcia warstw blachy bimetalowej w procesie walcowania = The numerical modelling of the layers flow velocity in bimetal plates rolling proces
PublicationW pracy przedstawiono wyniki obliczeń numerycznych dotyczących procesu asymetrycznego walcowania blach bimetalowych 18G2A+1H13.
-
The reactions occuring on the implant as a result of contact with human tissue
PublicationObecnosc implantu w ciele czlowieka powoduje liczne, czesto nieprzewidywalne skutki. Powodem takiej sytuacji jest duza roznorodnosc interakcji materialu medycznego z kontaktujaca sie z nim tkanka. Stwierdzenie to dotyczy glownie oddzialywan i skutkow zachodzacych na poziomie molekularnym w poszczegolnych komorkach kontaktujacej sie tkanki.
-
Allergy to implant components: chromium, nickiel, cobalt and titanium
PublicationImplant jest kompozycja roznych pierwiastkow: niklu, chromu, kobaltu, tytanu, molibdenu i wanadu. Pierwiastki te moga doprowadzic do alergii, egzemy i obluzowania implantu.
-
Adhesive compliance effect in mode I separation:Profilometry approach
PublicationThe effect of adhesive compliance on the deflection of a loaded, bonded beam was studied using laser profilometry. Experimental data obtained were compared with both Euler-Bernoulli (encastré) and Winkler (one parameter elastic foundation) models. A third, analytical, 2D model, based on shear within the adhesive layer (two parameter elastic foundation), was introduced. Finite element analysis (FEA) was also used to study the effect...
-
Badania elementów metalowych w celu określenia procesu wytwarzania
PublicationWykonano badania metalograficzne elementów metalowych w celu określenia technologii ich wykonania. Sformułowano wnioski.
-
Badania próbek wg wymagań normy SEP1390
PublicationWykonano badania próbek i sformułowano wnioski
-
Opinia dla Sądu Rejonowego Gdańsk-Północ w sprawie przyczyn pęknięcia grzejnika
PublicationWykonano badania i omówiono przyczyny uszkodzenia grzejnika
-
Spawanie łukiem krytym ze zwiększoną wydajnością
PublicationAnalizowano metody spawania ze zwiększoną wydajnością. Badano możliwość zastosowania dodatkowego ''zimnego'' drutu podawanego do łuku przy spawaniu automatycznym łukiem krytym pod topnikiem. Opracowano technologię takiego spawania i stwierdzono, że przy zwiększeniu wydajności spawania o około 36%$ w stosunku do spawania konwencjonalnego możliwe jest uzyskiwanie złączy doczołowych spełniających wymagania morskich towarzystw klasyfikacyjnych....
-
Wpływ czasu i temperatury utleniania na napawane warstwy ze stopu kobaltu
PublicationBadano wpływ czasu utleniania na strukturę i skład chemiczny warstw ze stopu kobaltu wytworzonych metodą napawania laserowego. Do napawania użyto proszku o wysokiej zawartości chromu i średniej zawartości wolframu. Utlenianie przeprowadzono w temperaturze 1100 degC w czasach od 15 minut do 50 godzin. Porównano uzyskane wyniki ze skutkami utleniania w temperaturze 750 degC w czasie 200 godzin. Stwierdzono postępującą degenerację...
-
Porous biomaterial for orthopaedic implants based on titanium alloy
PublicationTytan i jego stopy są szeroko stosowane jako biomateriały dla zastosowań ortopedycznych. Badania związane z ich najlepszą odpornością na korozję i ścieranie, biozgodnością i bioaktywnością są stale prowadzone. Obecne badania koncentrują się również na projektowaniu i produkcji materiałów porowatych w oparciu o stopy np. Ti-13Nb-13Zr, które mogą być stosowane do wytwarzania implantów. Jedną z najbardziej efektywnych metod wytwarzania...
-
Reactions on the surface of the implant under the influence of biofilm
PublicationThe contact of a biomaterial with the biological environment in in vitro and in vivo tests leads to the production of a particular ecosystem in which the active roles perform both, the material surface and the extracellular matrix protein forming a biofilm. Proteins affect cell and bacteria adhesion processes, biological activity of cells and activation of inflammatory response.The knowledge of the reaction mechanisms active on...
-
Allergic reactions as a defense of the organism to the influence of implants components made of stainless steel
PublicationDue to the increasing number of cases of hypersensitivity caused by direct contact with metals, as well as the increasing demand for implants in humans all ages numerous studies on the effects of the impact of implant components are being carried out. The paper presents the phenomenon of etiology of allergy in general terms and in relation to the biomaterials used in medicine. There have been characterized in terms of impact on...
-
Nanotechnologies in Development of Structural Materials and Biomaterials
PublicationThe nanometric materials and technologies resulted in nanostructures are reviewed. The examples of nanomaterials are shown. The typical nanotechnologies, including plastic deformation, mechanical attrition, controlled detonation, hot plasma jet synthesis, laser vaporisation, CVD and PVD, mechanical milling, annealing, ultrasonic irradiation, nanolithography, electrocrystallisation, electrospinning, sol-gel method, cryogenic laser-enhanced...
-
Badania wkrętów metalowych 25x3, 45x3, 125x3, 35x1,5 i 45x1,5
PublicationWykonano badania wkrętów metalowych w celu identyfikacji materiału i procesu wytwarzania.
-
Badania wkrętów metalowych 25x1,5
PublicationWykonano badania wkrętów celu identyfikacji materiału i procesu wytwarzania.
-
Wpływ parametrów spawania pod wodą metodą lokalnej komory suchej na strukturę i właściwości złączy
PublicationW artykule przedstawiono wyniki badań wpływu parametrów spawania pod wodą metodą lokalnej komory suchej na właściwości złączy. Analizowano wpływ ilości wprowadzonego ciepła oraz rodzaju gazu osłonowego na strukturę i twardość napoin. Opracowano zależności analityczne umożliwiające oszacowanie twardości maksymalnej w strefie wpływu ciepła.
-
Effets de variabilite d'adhesion et de viellissement en collage structural
PublicationDivers essais peuvent etre employes afin d'evaluer la resistance a la fracture des joints adhesifes. Generalement, ces essais sont symetriques: les substrats sont identiques. Nous avons utilise une version asymetrique, ou un adherend flexible est colle a aderend rigide. Nous discutons ici du comportement d'un joint d'adhesion variable. Des resultats assez surprenants font le sujet prinicpal de cet article.
-
Certyfikowanie nurków-spawaczy przy spawaniu mokrym pod wodą w warunkach hiperbarycznych
PublicationW artykule omówiono wymagania normy PN-EN ISO 15618-1:2002: Egzamin kwalifikacyjny spawaczy w zakresie spawania podwodnego. Część 1: Spawacze-nurkowie spawający na mokro w warunkach hiperbarycznych. Podano zakresy możliwych do uzyskania zakresów kwalifikacji, wytyczne odnośnie wszystkich zmiennych zasadniczych ujętych w normie oraz przykłady oznaczenia uprawnień nurka-spawacza. Wskazano treści, które należy poddać analizie przy...
-
The effect of long-term service at elevated temperatures on structure and mechanical properties of Cr-Mo-V steel
PublicationPurpose: of this paper is to reveal the microstructural changes in 13HMF steel exposed to long-term service at elevated temperatures. The degradation of bainite structure was determined and carbides morphology has been examined. The influence of carbides evolution was discussed in dependence of creep rupture strength and mechanical properties of the steel.
-
Badania radiograficzne zgrzein puszek zawierających produkt
PublicationWykonano badania zgrzein puszek zawierających produkt. Na podstawie uzyskanych wyników sformułowano wnioski.