Filters
total: 678
filtered: 621
Search results for: ELECTROMAGNETIC CLOAK
-
Fixed Pattern Noise Reduction and Linearity Improvement in Time-Mode CMOS Image Sensors
PublicationIn the paper, a digital clock stopping technique for gain and offset correction in time-mode analog-to-digital converters (ADCs) has been proposed. The technique is dedicated to imagers with massively parallel image acquisition working in the time mode where compensation of dark signal non-uniformity (DSNU) as well as photo-response non-uniformity (PRNU) is critical. Fixed pattern noise (FPN) reduction has been experimentally validated...
-
Evaluation of propagation parameters of open guiding structures with the use of complex root finding algorithms
PublicationAn efficient complex root tracing algorithm is utilized for the investigation of electromagnetic wave propagation in open guiding structures. The dispersion characteristics of propagated and leaky waves are calculated for a couple of chosen waveguides. The efficiency of the root tracing algorithm is discuses and compared to a global root finding algorithm.
-
Modelling and simulations in time-fractional electrodynamics based on control engineering methods
PublicationIn this paper, control engineering methods are presented with regard to modelling and simulations of signal propagation in time-fractional (TF) electrodynamics. That is, signal propagation is simulated in electromagnetic media described by Maxwell’s equations with fractional-order constitutive relations in the time domain. We demonstrate that such equations in TF electrodynamics can be considered as a continuous-time system of...
-
An analysis of solar energy conversion systems based on photon and thermal processes
PublicationSolar spectral irradiance covers a fairly broad wavelength range. Solar radiation is part of the electromagnetic spectrum which is described by the concept of wave-particle duality. The corpuscular theory of electromagnetic radiation states that energy is transmitted by photons. Photons carry specific amounts of energy which can be used to convert solar energy into other types of energy, in particular electricity. The internal...
-
An Analysis of Scattering from Ferrite Post of Arbitrary Convex Cross Section with the Use of Field Matching Method
PublicationA problem of electromagnetic wave scattering from ferrite post is presented. The post is assumed to be located in closed areas as waveguide junction, or in open area illuminated by a plane wave. The object is of arbitrary convex cross section and the method of analysis is semi-analytical, based on the direct field matching technique.
-
Virtual Engineering Factory: Creating Experience Base for Industry 4.0
PublicationABSTRACT In recent times, traditional manufacturing is upgrading and adopting Industry 4.0, which supports computerization of manufacturing by round-the-clock connection and communica- tion of engineering objects. Consequently, Decisional DNA- based knowledge representation of manufacturing objects, processes, and system is achieved by virtual engineering objects (VEO), virtual engineering processes (VEP), and virtual engineering...
-
Design and optimization of a novel miniaturized low-profile circularly polarized wide-slot antenna
PublicationThis paper presents a novel structure of a compact circularly polarized (CP) antenna. CP is obtained using a parasitic quasi-rectangular strip placed coplanar to the feedline. A ground plane perturbation combined with the asymmetric geometry of the coplanar waveguide ground planes is utilized to excite additional CP modes. All antenna dimensions are rigorously optimized to achieve the best possible performance in terms of the impedance...
-
Resonance microstrip structure with patch of arbitrary convex geometry with the use of field matching technique
PublicationAn analysis of the resonance frequency problem of planar microstrip structure with patch of arbitrary convex geometry is presented. A full-wave analysis is employed utilizing a combination of Galerkin’s moment method and field matching technique. In this approach, a field matching technique is adopted to calculate the patch surface current densities, and next the method of moments is utilized to calculate resonance frequencies...
-
Finite element/mode-matching analysis of ferrite/dielectric line junctions of arbitrary cross-section
PublicationThis paper is focused on the analysis of line junctions obtained as a cascade of dielectric and ferrite guides of arbitrary cross-section. The main application of such structures is nonreciprocal devices such as isolators, circulators, or phase shifters. The efficient finite element/mode-matching approach is proposed to the analysis of such structures. In this approach, thefiniteelementmethod is applied todetermine propagation...
-
Left-handed propagation characteristics of a dielectric and metal-loaded periodic circular waveguide
PublicationIn this paper, a periodic dielectric/metallic rod is located in a circular waveguide to obtain left-handed operation. Two geometries of the dielectric/metallic rod are proposed and examined. The dispersion characteristics of the investigated waveguides are obtained using a surface impedance model. Moreover, equivalent circuit models are proposed allowing for calculation of the dispersion characteristics and scattering parameters...
-
Recurrence scheme for FDTD-compatible discrete Green's function derived based on properties of Gauss hypergeometric function
PublicationIn this paper, the formulation of one-dimensional FDTD (Finite-difference time-domain)-compatible discrete Green's function (DGF) is derived based on the Gauss hypergeometric function (GHF). The properties of GHF make it possible to derive the recurrence scheme only in the time domain for the DGF generation. Furthermore, this recurrence scheme is valid for any stable time-step size and can be implemented using standard numerical...
-
Low Frequency Conducted Emissions of Grid Connected Static Converters
PublicationPulse-width modulated rectifiers are nowadays commonly used for AC to DC power conversion. PWM rectification technology is very effective and allows for bidirectional power flow with the possibility of power factor improvement and low-order harmonic emission limitation. Unfortunately, employed PWM boost topology results with generation of input current harmonic distortions in a frequency range tightly correlated to modulation frequency....
-
CM Voltage Compensators for Power Electronic Interfaces
PublicationThe experimental results presented in the paper have shown that the application of the PEIs might cause EMC related problems, especially in the case of the application of a group of connected converters. The most convenient way to reduce EMI currents and prevent aggregation of EMI currents introduced by a group of converters is through passive compensation of voltage interference sources inside of the single converters. In the...
-
Scattering by an array of conducting, lossy dielectric, ferrite and pseudochiral cylinders.
PublicationOpisano metodę analizy rozpraszania fali elektromagnetycznej w systemach zawierających cylindryczne pręty dielektryczne, metalowe, ferytowe i pseudochiralne i wykorzystanie w/w metody w problemach zamkniętych i znajdowanie macierzy rozpraszania wieloportowych złączy falowodowych oraz w problemach otwartych i badanie charakterystyk rozpraszania zarówno w strefie dalekiej jaki bliskiej.
-
Design of UWB coplanar antenna with reduced ground plane
PublicationW artykule przedstawiono projekt kompaktowej anteny szerokopasmowej złożonej z dwóch kołowych pasków koplanarnych ograniczających szczelinę o podobnym kształcie. Antena zasilona była z 50 Ω linii trójpaskowej. Przeprowadzono badania wpływu zewnętrznego paska na pasmo anteny. Zaprojektowana antena została zbadana eksperymentalnie pokazując bardzo dobre parametry: w paśmie 1.7-15.5GHz uzyskano |S11| < −10dB. Antena charakteryzowała...
-
Objective selection of minimum acceptable mesh refinement for EMC simulations
PublicationOptimization of computational electromagnetics (CEM) simulation models can be costly in both time and computing resources. Mesh refinement is a key parameter in determining the number of unknowns to be processed. In turn, this controls the time and memory required for a simulation. Hence, it is important to use only a mesh that is good enough for the objectives of the simulation, whether for direct handling of high-fidelity EM...
-
Experimental and numerical investigation of crosstalk effect in coupled coplanar waveguides - part II: Multimode coupled line representation
PublicationW pracy przedstawiono metodę analizy nieidealności połączenia poszczegółnych fragmentów rozłożonego ekranu na zjawisko przesłuchu w strukturze sprzężonych falowodów koplanarnych z uziemionym centralnym paskiem. Analiza bierze pod uwagę efekty dyspersji oraz wielorodzajową naturę rozchodzenia się fali elektromagnetycznej w strukturze wieloprzewodowej. Teorię zweryfikowano praktycznie uzyskując bardzo dobrą zgodność pomiędzy wynikami...
-
Experimental and numerical investigation of crosstalk effect in coupled coplanar waveguides - part i: bi-mode coupled line representation
PublicationW pracy przedstawiono analizę zjawiska przesłuchu w strukturze sprzężonych falowodów koplanarnych. Analiza wykorzystując metodę przestrzeni widmowej i bazując na dwurodzajowym modelu pary linii sprzężonych uwzględnia efekty dyspersji obserwowane w zakresie wysokich częstotliwośći. Przedyskutowano zagadnienie sposobu definicji impedancji charakterystycznych dla prowadzonych rodzajów pola. Wyniki modelowania numerycznego potwierdzono...
-
Investigations of nonreciprocal devices employing cylindrical ferrite coupled line junction
PublicationArtykuł opisuje wykorzystanie cylindrycznej sekcji ferrytowych linii sprzężonych do realizacji układów niewzajemnych. W artykule opisano proces projektowy izolatora ferrytowego wykorzystującego badaną sekcję oraz planarne układy zasilające. Uzyskane z symulacji wyniki zostały zweryfikowane eksperymentalnie.
-
Rapid multi-objective design of integrated on-chip inductors by means of Pareto front exploration and design extrapolation
PublicationIdentification of the best trade-offs between conflicting design objectives allows for making educated design decisions as well as assessing suitability of a given component or circuit for a specific application. In case of inductors, the typical objectives include maximization of the quality factor and minimization of the layout area, as well as maintaining a required inductance at a given operating frequency. This work demonstrates...
-
Detekcja osoby w wannie
PublicationStarzenie się społeczeństwa powoduje narastanie problemów chorób wieku starczego. Częstym problemem są zasłabnięcia w wannie podczas kąpieli. Celem publikacji jest przedstawienie metody identyfikacji tkanki ożywionej w wodzie z wykorzystaniem technik elektromagnetycznych. Obserwując zmiany amplitudy i częstotliwości pracy generatorów, pracujących w pętli sprzężenia zwrotnego z cewką, istnieje możliwość scharakteryzowania i określenia...
-
Aggregated conducted interferences generated by group of asynchronous drives with deterministic and random modulation
PublicationThis paper addresses problems linked with electromagnetic interferences generated by group of three adjustable speed drives fed by frequency converters with deterministic and random modulation. Based on the experimental results it has been shown that decreasing of the conducted interferences in a case of random modulation is measuring phenomenon linked with selectivity of the EMI receiver.
-
A Compact Basis for Reliable Fast Frequency Sweep via the Reduced-Basis Method
PublicationA reliable reduced-order model (ROM) for fast frequency sweep in time-harmonic Maxwell’s equations by means of the reduced-basis method is detailed. Taking frequency as a parameter, the electromagnetic field in microwave circuits does not arbitrarily vary as frequency changes, but evolves on a very low-dimensional manifold. Approximating this low-dimensional manifold by a low dimension subspace, namely, reduced-basis space, gives...
-
Accelerated simulation-driven design optimisation of compact couplers by means of two-level space mapping
PublicationIn this study, the authors discuss a robust and efficient technique for rapid design of compact couplers. The approach exploits two-level space mapping (SM) correction of an equivalent circuit model of the coupler structure under design. The first SM layer (local correction) is utilised to ensure good matching between the equivalent circuit and the electromagnetic model at the component level. Subsequent global correction allows...
-
Simulation of Wave Propagation in Media Described by Fractional-Order Models
PublicationIn this paper, algorithms for simulation of the wave propagation in electromagnetic media described by fractional-order (FO) models (FOMs) are presented. Initially, fractional calculus and FO Maxwell's equations are introduced. The problem of the wave propagation is formulated for media described by FOMs. Then, algorithms for simulation of the non-monochromatic wave propagation are presented which employ computations in the time...
-
Asynchronous WAM with Irregular Pulse Repetition
PublicationRadiolocation systems for aviation based on Multi-Lateration (MLAT) typically use a set of synchronised ground sensors to receive radio signals broadcast by onboard transmitters. In most cases, the sensor synchronisation in Wide Area Multi-Lateration Systems (WAM) is provided by Global Navigation Satellite System (GNSS) receivers. However, in the case of synchronisation failure, there is still a possibility to estimate the coordinates...
-
Kinedynamics of Spherical Wavefields in Fluid and Dielectric Continua
PublicationDistubances induced by physical sources in fluids or dielectrics maintain their primary character while propagating throughout either of these bi-dynamic continua. The paper defines and illustrates four sets of bi-fields based on four specific fundamental kinedynamic solutions to inhomogeneous wave equations related to quasi-point acoustic and electromagnetic sources.
-
Mathemathical model of radial passive magnetic bearing
PublicationIn the article mathematical radial model of passive magnetic bearings to ocean engineering units has been presented. The units application in underwater thrusters should increase propulsion systems durability and gives lower maintenance costs. The rotor of electric motor is hanging in magnetic field taken from radial passive magnetic bearings. However axial direction maintenance must be controlled with electromagnets and their...
-
An Analysis of Periodic Arrangements of Cylindrical Objects of Arbitrary Convex Cross Sections with the Use of Field Matching Method
PublicationA problem of electromagnetic wave scattering from multilayered frequency selective surfaces is presented. Each surface is composed of periodically arranged cylindrical posts of arbitrary convex cross-section. The method of analysis is based on the direct field matching technique for a single cell, and the transmission matrix method with the lattice sums technique for periodic arrangement of scatterers.
-
Overview of planar antenna loading metamaterials for gain performance enhancement: the two decades of progress
PublicationMetamaterials (MTMs) are artificially engineered materials with unique electromagnetic properties not occurring in natural materials. MTMs have gained considerable attention owing to their exotic electromagnetic characteristics such as negative permittivity and permeability, thereby a negative refraction index. These extraordinary properties enable many practical applications such as super-lenses, and cloaking technology, and are...
-
Extraction of antenna pattern from near field antenna measurements distorted by undesired emission
PublicationIn this paper authors present experimental correction of antenna pattern obtained from near field measurements when they are distorted by determined electromagnetic emission. Such situation may be met e.g. when feeding or supply subsystem interacts with antenna radiation pattern due to self-emission. Presented results of experiments show effectiveness of extraction of antenna pattern utilizing near field antenna measurements.
-
Local-Global Space Mapping for Rapid EM-Driven Design of Compact RF Structures
PublicationIn this work, we introduce a robust and efficient technique for rapid design of compact RF circuits. Our approach exploits two-level space mapping (SM) correction of an equivalent circuit model of the structure under design. The first SM layer (local correction) is utilized to ensure good matching between the equivalent circuit and the electromagnetic model at the component level. On the other hand, the global correction allows...
-
Design Space Reduction for Expedited Multi-Objective Design Optimization of Antennas in Highly-Dimensional Spaces
PublicationA surrogate-based technique for efficient multi-objective antenna optimization is discussed. Our approach exploits response surface approximation (RSA) model constructed from low-fidelity antenna model data (here, obtained through coarse-discretization electromagnetic simulations). The RSA model enables fast determination of the best available trade-offs between conflicting design goals. The cost of RSA model construction for multi-parameter...
-
Integrated Application of GPR and Ultrasonic Testing in the Diagnostics of a Historical Floor
PublicationThe paper presents the results of integrated ground penetrating radar (GPR) and ultrasonic testing (UT) measurements conducted on a historical floor in St. Nicholas’ Church, Gdańsk, Poland. The described inspection was the first stage of the technical state assessment of the building. The aim of the study was the detection of underfloor air gaps, which were observed in a few trial pits. The condition of the ground under the floor...
-
Automated microwave planar filter design with generalized Chebyshev characteristics.
PublicationIn this paper a technique of automatization of design of microwave filters with generalized Chebyshev characteristics is presented. A full wave electromagnetic simulator linked with the Matlab computing environment is used to ensure a rigorous numerical analysis while at the same time allowing automatization. To decrease time of optimization and overall design process, the Cauchy interpolation technique was used. An automated design...
-
GPU-accelerated finite element method
PublicationIn this paper the results of the acceleration of computations involved in analysing electromagnetic problems by means of the finite element method (FEM), obtained with graphics processors (GPU), are presented. A 4.7-fold acceleration was achieved thanks to the massive parallelization of the most time-consuming steps of FEM, namely finite-element matrix-generation and the solution of a sparse system of linear equations with the...
-
Fast Antenna Optimization Using Gradient Monitoring and Variable-Fidelity EM Models
PublicationAccelerated simulation-driven design optimization of antenna structures is proposed. Variable-fidelity electromagnetic (EM) analysis is used as well as the trust-region framework with limited sensitivity updates. The latter are controlled by monitoring the changes of the antenna response gradients. Our methodology is verified using three compact wideband antennas. Comprehensive benchmarking demonstrates its superiority over both...
-
Mixed electromagnetic - circuits modeling and parallelization for rigorouscharacterization of cosite interference in wireless communication channels. W: UGC 2002 Homepage [online]. Department of Defense High Performance Com- puting Modernization Program. Users Group Conference 2002. Austin, Texas, USA. June 10-14, 2002. [Dostęp: 15 grudnia**2002]. Dostępny w World Wide Web: http://www.hpcmo.hpc.mil/Htdocs/UGC/UGC02/paper/[45 slajdów]. Modelowanie układów elektromagnetycznych i zrównoleglanie w celu określenia wzajemnych oddziaływań w bezprzewodowych kanałach komunikacyjnych.
PublicationRównoległe działanie sąsiadujące modułów nadawczo-odbiorczych typowo prowa-dzi do efektów ubocznych z powodu wzajemnych oddziaływań, które obniżają pa-rametry sieci. W celu scharakteryzowania takich efektów, zaprezentowano roz-wiązanie równań Maxwella w dziedzinie czasu z modelowaniem efektów nielinio-wych.
-
Hybrid technique for the analysis of scattering from periodic structures composed of irregular objects
PublicationW pracy zaproponowano nową metodę hybrydową do badania zjawiska rozpraszania fali elektromagnetycznej na strukturach periodycznych złożonych z obiektów rozpraszających o nieregularnym kształcie. Zaprezentowana metoda została wykorzystana do badania własności nowych struktur falowych. Uzyskane wyniki numeryczne zostały zweryfikowane eksperymentalnie.
-
Implementation of FDTD-compatible Green's function on heterogeneous CPU-GPU parallel processing system
PublicationThis paper presents an implementation of the FDTD-compatible Green's function on a heterogeneous parallel processing system. The developed implementation simultaneously utilizes computational power of the central processing unit (CPU) and the graphics processing unit (GPU) to the computational tasks best suited to each architecture. Recently, closed-form expression for this discrete Green's function (DGF) was derived, which facilitates...
-
A Novel Synthesis Technique for Microwave Bandpass Filters with Frequency-Dependent Couplings
PublicationThis paper presents a novel synthesis technique for microwave bandpass filters with frequency-dependent couplings. The proposed method is based on the systematic extraction of a dispersive coupling coefficient using an optimization technique based on the zeros and poles of scattering parameters representing two coupled resonators.The application of this method of synthesis is illustrated using two examples involving four and five-pole...
-
Applications of the discrete green's function in the finite-difference time-domain method
PublicationIn this paper, applications of the discrete Green's function (DGF) in the three-dimensional (3-D) finite-difference time-domain (FDTD) method are presented. The FDTD method on disjoint domains was developed employing DGF to couple the subdomains as well as to compute the electromagnetic field outside these subdomains. Hence, source and scatterer are simulated in separate subdomains and updating of vacuum cells, being of little...
-
FINITE GROUND CPW-FED UWB ANTENNA OVER THE METALLIC CYLINDRICAL SURFACES
PublicationThe investigation of finite ground coplanar fed ultra-wideband (UWB) antenna and the influence of its curvature and the proximity of circular metallic screen on the reflection coefficients and radiation characteristics is presented. The antenna is composed of two circular coplanar strips which enclose slot aperture of similar shape and is designed on a thin and flexible substrate which allows its bending. The antenna configuration...
-
Analysis of scattering from arbitrary configuration of cylindrical objects using hybrid finite-difference mode-matching method
PublicationW artykule przedstawiono nową metodę hybrydową stanowiącą połączenie metody różnic skończonych z metodą dopasowania rodzajów, pozwalającą na analizę obiektów cylindrycznych o dowolnym przekroju poprzecznym. W prezentowanej metodzie poszczególne obiekty reprezentowane są poprzez wielorodzajową macierz impednacyjną zdefiniowaną na powierzchni bocznej zastępczego cylindra zawierającego badany obiekt. Celem określenia parametrów rozproszenia...
-
Propagation in a ferrite circular waveguide magnetized through a rotary four-pole magnetic field
PublicationOpracowano uproszczony model matematyczny użyteczny do badania zjawisk polowych występujących w falowodzie cylindrycznym magnesowanym czterobiegunowym polem obrotowym. Wykazano, że falowód ten może być wykorzystany jako przesuwnik fazy lub układ zmieniający polaryzację.
-
A memory efficient and fast sparse matrix vector product on a Gpu
PublicationThis paper proposes a new sparse matrix storage format which allows an efficient implementation of a sparse matrix vector product on a Fermi Graphics Processing Unit (GPU). Unlike previous formats it has both low memory footprint and good throughput. The new format, which we call Sliced ELLR-T has been designed specifically for accelerating the iterative solution of a large sparse and complex-valued system of linear equations arising...
-
Rectangular microstrip resonator illumi-nated by normal-incident plane wave
PublicationW pracy przedstawiono koncepcję modów oświetlających pozwalającą na obliczenie podstawowych parametrów elektrycznych anten mikropaskowych - częstotliwości rezonansowej, rezystancji promieniowania i charakterystyki promieniowania. Oparta jest ona na dwuwymiarowej metodzie przestrzeni widmowej, w której pobudzenie występuje w formie pojedynczej fali płaskiej padającej prostopadle na analizowaną strukturę. Rezultatem takiego podejścia...
-
Study of nonreciprocal devices using three-strip ferrite coupled line
PublicationW pracy przedstawiono badania układów niewzajemnych wykorzystujących nowe złącze ferrytowych linii sprzężonych, zaprojektowane w oparciu o linię koplanarną, w której półpłaszczyzny masy zredukowane zostały do postaci pasków. Badane złącze złożone jest z sekcji ferrytowej umieszczonej pomiędzy dwoma sekcjami dielektrycznymi. W sekcji ferrytowej podłużnie magnesowana płytka ferrytowa umieszczona jest pod lub nad paskami przewodzącymi...
-
Investigations of cylindrical ferrite coupled line junction using hybrid technique
PublicationW pracy zaproponowano nowe cylindryczne złącze magnesowanych wzdłużnie ferrytowych linii sprzężonych. W porównaniu do znanych w literaturze planarnych konfiguracji złączy ferrytowych, zaproponowana struktura charakteryzuje się znacznie wyższym współczynnikiem sprzężenia żyrotropowego. Pozwala to na uzyskanie wymaganej w układach niewzajemnych rotacji Faraday'a o kąt 45 stopni przy znacznie krótszej długości sekcji linii ferrytowych...
-
Efficient Multiscale Finite Difference Frequency Domain Analysis Using Multiple Macromodels with Compressed Boundaries
PublicationW niniejszym artykule zaprezentowany został nowatorski pomysł na zmniejszenie numerycznej złożoności metody różnic skończonych przy użyciu wielu makromodeli. Skuteczność techniki macromodelingu zależy od liczby portów modelu. Aby zwiększyć efektywność algorytmu, próbki pola na granicy makromodeli są zastępowane przez amplitudy wielomianów Legendre'a. Przedefiniowanie problemu w taki sposób powoduje znaczną redukcję czasu analizy....