Search results for: UNIPLANAR ANTENNAS
-
Vehicular Communication Environments
PublicationCommunication to and between road vehicles (cars, truck, buses, trains, etc.) are of growing interest. This is partly due to the attractive services that cooperative intelligent transport systems (C-ITSs) provides, mainly in the areas of traffic safety and traffic efficiency. An enabler for C-ITS is wireless vehicle-to-vehicle (V2V) and vehicle-to-infrastructure (V2I) communication, collectively referred to as vehicle-to-X (V2X)...
-
Measurements of Path Loss in Off-Body Channels in Indoor Environments
PublicationThe main goal of the paper is to investigate the influence of body orientation and on-body antenna placement on the path loss in off-body communications. In addition, the influence of different bodies is analysed.
-
Path Loss Analysis in Off-Body Channels in Indoor Environment
PublicationThis temporary document describes an analysis of path loss in off-body channels in an indoor environment. The influence of body orientation and on-body antenna placement on path loss in off-body communications as well as of different bodies has been investigated. Five static scenarios, six distances between body and antenna and eight body orientations were analysed; moreover, two dynamic scenarios were investigated. The smallest...
-
Design and experimental verification of multi-layer waveguide using pin/hole structure
PublicationThis study presents a novel technique for minimizing RF leakage in metallic hollow waveguides fabricated using the multilayer split-block method. By integrating a pin/hole wall into the split-block multilayers, a substantial reduction of RF leakage can be achieved while reducing the circuit size and mitigating the performance variations. To validate the proposed approach, a slot antenna fed by single ridge waveguide has been prototyped...
-
Pomiarowa ocena efektywności systemu antyspoofingowego opartego na przetwarzaniu wieloantenowym
PublicationNiniejszy referat dotyczy problemu wykrywania i przeciwdziałania atakom typu spoofing w globalnych systemach nawigacji satelitarnej. Pierwsza część referatu stanowi wprowadzenie w temat spoofingu oraz przegląd sposobów jemu przeciwdziałania. Następnie, przedstawiono autorską koncepcję systemu antyspoofingowego opartego na przetwarzaniu wieloantenowym, a także opisano implementację prototypu tego systemu. Część trzecią poświęcono...
-
[Komentarz do artykułu] Yin, W.-Y., Wu, B., Miao, M., Doi, L.B., Li, L.-W., and Kooi, P.-S.: Experimental characterisation and modelling of on-chip capacitors and resistors on GaAs substrates.
PublicationDokonano krytycznej oceny wartości elementów schematu zastępczego rezystorów monolitycznych wykonanych na podłożu GaAs przedstawionych w pracy: Yin, W.-Y., Wu, B., Miao, M., Doi, L.B., Li, L.-W., and Kooi, P.-S.: Experimental characterisation and modelling of on-chip capacitors and resistors on GaAs substrates, IEE Proc. Microw. Antennas and Propag., 2002,149, (1), pp.50-52.
-
System Loss in UWB Off-Body Communications in a Ferry Environment
PublicationIn this paper, the system loss in UWB off-body communications in a ferry environment based on measurements is presented. A mobile measurement set-up, consisting of WBAN nodes with UWB DWM1000 modules, was used. System loss was split into LOS and NLOS conditions. For the former, the smallest mean value, 24.4 dB, was obtained for the user approaching the fixed terminal, with the antenna on his chest, and the largest, 28.1 dB, for...
-
Recent advances in high-frequency modeling by means of domain confinement and nested kriging
PublicationDevelopment of modern high-frequency components and circuits is heavily based on full-wave electromagnetic (EM) simulation tools. Some phenomena, although important from the point of view of the system performance, e.g., EM cross-coupling effects, feed radiation in antenna arrays, substrate anisotropy, cannot be adequately accounted for using simpler means such as equivalent network representations. Consequently, the involvement...
-
Recent Advances in Accelerated Multi-Objective Design of High-Frequency Structures using Knowledge-Based Constrained Modeling Approach
PublicationDesign automation, including reliable optimization of engineering systems, is of paramount importance for both academia and industry. This includes the design of high-frequency structures (antennas, microwave circuits, integrated photonic components), where the appropriate adjustment of geometry and material parameters is crucial to meet stringent performance requirements dictated by practical applications. Realistic design has...
-
Response Feature Technology for High-Frequency Electronics. Optimization, Modeling, and Design Automation
PublicationThis book discusses response feature technology and its applications to modeling, optimization, and computer-aided design of high-frequency structures including antenna and microwave components. By exploring the specific structure of the system outputs, feature-based approaches facilitate simulation-driven design procedures, both in terms of improving their computational efficiency and reliability. These benefits are associated...
-
Time domain model of the resonance-based electromagnetic pulses emission system
PublicationIn the literature, the emission properties of the electromagnetic field pulse systems based on high voltage antennas (HVR) have been widely described. In order to increase the emission efficiency by extending duration and increasing amplitude of the impulse it is possible to use a resonance system tuned to the parameters of the signal shaped in the pulse forming circuit. The synthesis of a time-domain simulation model of a complex...
-
Editorial for the special issue on advances in forward and inverse surrogate modeling for high-frequency design
PublicationThe design of modern‐day high‐frequency devices and circuits, including microwave/RF, antenna and photonic components, historically has relied on full‐wave electromagnetic (EM) simulation tools. Initially used for design verification, EM simulations are nowadays used in the design process itself, for example, for finding optimum values of geometry and/or material parameters of the structures of interest. In a growing number of...
-
Wideband Channel Measurements for Polarised Indoor Off-Body Communications
PublicationThis paper presents the initial results of wideband channel measurements for polarised off-body communication at 5.8 GHz, in an indoor environment. Channel Impulse Response measurements were performed simultaneously for two orthogonal polarisations of the wearable antenna, and repeated for vertical and horizontal orientations of the off-body one. Four types of measurement scenarios were considered in order to investigate the influence...
-
An Empirical System Loss Model for Body Area Networks in a Passenger Ferry Environment
PublicationThis paper presents a general empirical system loss model for estimating propagation loss in Body Area Networks in off-body communications at 2.45 GHz in a passenger ferry environment. The model is based on measurements, which were carried out in dynamic scenarios in the discotheque passenger ferry environment. The model consists of three components: mean system loss, attenuation resulting from the variable antenna position on...
-
Implementation of DIFAR Processing in ASW Dipping Sonar
PublicationThis paper presents the implementation of the signal processing algorithm used by buoy DIFAR (Directional Frequency Analysis and Recording), that is fully operational on Polish Navy anti-submarine warfare (ASW) helicopters and ships, applied to dipping sonars for detection and tracking of submarines. The development of the DSP algorithms was a part of the modernization of sonars conducted at the Gdansk University of Technology....
-
An Empirical System Loss Model for Body Area Networks in a Passenger Ferry Environment
PublicationThis paper presents a general empirical system loss model for estimating propagation loss in Body Area Networks in off-body communications at 2.45 GHz in a passenger ferry environment. The model is based on measurements, which were carried out in dynamic scenarios in the discotheque passenger ferry environment. The model consists of three components: mean system loss, attenuation resulting from the variable antenna position on...
-
Local response surface approximations and variable-fidelity electromagnetic simulations for computationally efficient microwave design optimisation
PublicationIn this study, the authors propose a robust and computationally efficient algorithm for simulation-driven design optimisation of microwave structures. Our technique exploits variable-fidelity electromagnetic models of the structure under consideration. The low-fidelity model is optimised using its local response surface approximation surrogates. The high-fidelity model is refined by space mapping with polynomial interpolation of...
-
Mateusz Groth mgr inż.
People -
Łukasz Szczygielski mgr inż.
People -
A New Expression for the 3-D Dyadic FDTD-Compatible Green's Function Based on Multidimensional Z-Transform
PublicationIn this letter, a new analytic expression for the time-domain discrete Green's function (DGF) is derived for the 3-D finite-difference time-domain (FDTD) grid. The derivation employs the multidimensional Z-transform and the impulse response of the discretized scalar wave equation (i.e., scalar DGF). The derived DGF expression involves elementary functions only and requires the implementation of a single function in the multiple-precision...
-
A Low-Profile Metal-backed Dipole Loaded with Closely Coupled Arc-shaped Open Stubs for On-metal Tag Design with Wide Frequency Tuning Capability
PublicationThis research has presented a single-layer metal-backed dipole antenna, which consists of a feedline loaded with two pairs of closely-coupled arc-shaped open stubs, for designing a metal-mountable tag that features tuning capability over a wide range of frequency. Here, the stubs can generate sufficient inductive reactance for bringing down the tag resonant frequency tunable in both the regulated UHF RFID passbands (North American...
-
Investigation of the impact of ITRF2014/IGS14 on the positions of the reference stations in Europe
PublicationIn January 2017, the new realization of the International Terrestrial Reference Frame (ITRF) – ITRF2014, was released. Besides the higher accuracy and consistency of the new frame, an entirely new element – the post seismic deformation - was included. Moreover, the definition of the fundamental points has also been changed. All changes related to the new reference frame haveconsequences in the precise positioning using GNSS observations....
-
Coplanar Waveguide-Fed Broadband Microwave Devices with (or without) a Thin Dielectric Substrate for Use in Flexible Electronic Systems
PublicationTwo examples of microwave devices, fed by a coplanar waveguide and realized on a thin substrate (or without such a substrate), are employed to investigate the influence of devices’ curvatures and the proximity of different materials on their parameters. To perform the tests, a broadband antenna and a low-pass filter are chosen. A feeding coplanar waveguide is realized on a dielectric material brick attached to an SMA connector...
-
Selected acoustic images of the Gdansk Bay
PublicationThe main goal of the paper is to describe the results of sounding the Gdansk Bay seabed by using a parametric sub-bottom profiler, multibeam echosounder and side scan sonar. Quality of dsata obtained during trials depends interalia on a proper location of antenna to reduce influence of pitch, roll and heave motions as well as ship noise.
-
Twenty years' (1996-2016) tropospheric parameters for selected EPN stations derived from GPS double-difference processing
Open Research DataPropagation of global navigation satellite systems (GNSS) signals through the Earth’s atmosphere is affected by its physical properties. Both hydrostatic and wet part of the atmosphere (mostly related with troposphere) causes delays of GNSS signal, which usually are expressed in the zenith direction (zenith hydrostatic delay - ZHD, and zenith wet delay...
-
Twenty years' (1996-2016) tropospheric parameters for selected EPN stations derived from GPS precise point positioning
Open Research DataPropagation of global navigation satellite systems (GNSS) signals through the Earth’s atmosphere is affected by its physical properties. Both hydrostatic and wet part of the atmosphere (mostly related with troposphere) causes delays of GNSS signal, which usually are expressed in the zenith direction (zenith hydrostatic delay - ZHD, and zenith wet delay...
-
Periodicity Matters: Grating or lattice resonances in the scattering by sparse arrays of subwavelength strips and wires.
Publication -
A new hybrid method for analysis of scattering from arbitrary configuration of cylindrical objects
PublicationArtykuł opisuje nową hybrydową metodę analizy rozpraszania fali elektromagnetycznej od obiektów cylindrycznych o dowolnym przekroju poprzecznym. W prezentowanym podejściu każdy obiekt jest traktowany jako efektywny cylinder o przekroju kołowym, opisany przez macierz impedancyjną. W celu uzyskania owej macierzy zastosowano połączenie metod różnic skończonych w dziedzinie częstotliwości (FDFD) i dopasowania rodzajów (MM). W celu...
-
Analysis and design of a polarizer rotator system
PublicationW artykule przedstawiono metodę analizy wielosekcyjnego polaryzatora złożonego z periodycznych szyków obiektów cylindrycznych. W celu analizy badanej struktury zastosowano metodę pełnofalową opartą na metodzie dopasowania rodzajów. Opracowany algorytm został zweryfikowany poprzez porównanie uzyskanych wyników z wynikami otrzymanymi z przybliżonego modelu transmisyjnego oraz z własnymi pomiarami wykonanego prototypu.
-
Analysis of scattering from arbitrary configuration of elliptical obstacles using T-matrix representation
PublicationW artykule przedstawiono nową metodę analizy zjawiska rozpraszania dla dowolnej konfiguracji obiektów eliptycznych. Przedstawione podejście, dotyczącego pojedynczego obiektu, oparte jest na połączeniu analizy w układzie eliptycznym i cylindrycznym. W analizie wielu obiektów wykorzystana została procedura iteracyjna. Uzyskane wyniki zostały zweryfikowane przy wykorzystaniu oprogramowania komercyjnego.
-
Rapid multi-objective design optimisation of compact microwave couplers by means of physics-based surrogates
PublicationThe authors introduce a methodology for fast multi-objective design optimisation of miniaturised microwave couplers. The approach exploits the surrogate-based optimisation paradigm with an underlying low-fidelity model constructed from an equivalent circuit of the structure under consideration, corrected through implicit and frequency space mapping. A fast prediction tool obtained this way is subsequently optimised by a multi-objective...
-
Accelerated simulation-driven design optimisation of compact couplers by means of two-level space mapping
PublicationIn this study, the authors discuss a robust and efficient technique for rapid design of compact couplers. The approach exploits two-level space mapping (SM) correction of an equivalent circuit model of the coupler structure under design. The first SM layer (local correction) is utilised to ensure good matching between the equivalent circuit and the electromagnetic model at the component level. Subsequent global correction allows...
-
Rapid design of miniaturised branch-line couplers through concurrent cell optimisation and surrogate-assisted fine-tuning
PublicationIn this study, the authors introduce a methodology for low-cost simulation-driven design optimisation of highly miniaturised branch-line couplers (BLCs). The first stage of their design approach exploits fast concurrent optimisation of geometrically dependent, but electromagnetically isolated cells that constitute a BLC. The cross-coupling effects between the cells are taken into account in the second stage, where a surrogate-assisted...
-
GPU-Accelerated Finite-Element Matrix Generation for Lossless, Lossy, and Tensor Media [EM Programmer's Notebook]
PublicationThis paper presents an optimization approach for limiting memory requirements and enhancing the performance of GPU-accelerated finite-element matrix generation applied in the implementation of the higher-order finite-element method (FEM). It emphasizes the details of the implementation of the matrix-generation algorithm for the simulation of electromagnetic wave propagation in lossless, lossy, and tensor media. Moreover, the impact...
-
An Analysis of Elliptical-Rectangular Multipatch Structure on Dielectric-Coated Confocal and Nonconfocal Elliptic Cylinders
PublicationA rigorous analysis of the resonance frequency problem of an elliptical-rectangular microstrip structure mounted on dielectric-coated elliptic conducting cylinder, with electrically small radius, is investigated in this paper. A full-wave analysis and a moment-method calculation are employed. The analysis is carried out considering the expansion of the field as a series of Mathieu functions. The complex resonance frequencies of...
-
Accurate modelling of microwave structures using shape-preserving response prediction
PublicationArtykuł prezentuje metodologię dokładnego modelowania struktur mikrofalowych. Jest to zmodyfikowana wersja techniki opartej na procedurze przewidywania odpowiedzi z zachowaniem kształtu (shape-preserving response prediction, SPRP), która oszacowuje odpowiedź struktury mikrofalowej otrzymanej poprzez kosztowną obliczeniowo symulację elektromagnetyczną za pomocą taniego obliczeniowo modelu tejże struktury. Modyfikacja polega na wykorzystaniu...
-
Development of a compact microstrip resonant cell aimed at efficient microwave component size reduction
PublicationA comprehensive comparison of a wide collection of compact microstrip resonant cells (CMRCs) found in the extensive body of literature has been presented. The evaluation of different CMRC designs has led to the selection of the most promising CMRC geometry for the efficient miniaturisation of modern microwave components. In order to showcase the vital effectiveness of the approach, the initially selected CMRC has been notably...
-
A new approach to a fast and accurate design of microwave circuits with complex topologies
PublicationA robust simulation-driven design methodology of microwave circuits with complex topologies has been presented. The general method elaborated is suitable for a wide class of N-port unconventional microwave circuits constructed as a deviation from classic design solutions. The key idea of the approach proposed lies in an iterative redesign of a conventional circuit by a sequential modification and optimisation of its atomic building...
-
Hybrid technique for the analysis of circular waveguide junctions loaded with ferrite posts
PublicationThis study presents a hybrid technique for the analysis of circular waveguide junctions loaded with axially symmetrical ferrite posts of irregular shape. The method is based on a combination of the finite-difference frequency- domain technique with a mode-matching technique. The proposed approach is validated by comparing the presented results with numerical ones obtained from commercial software. The application of a cylindrical...
-
Measurement of Coherence Bandwidth in UHF Radio Channels for Narrowband Networks
PublicationThis paper presents results of investigation on the coherence bandwidth of narrowband radio channels in 430MHz band. The coherence bandwidth values were estimated froma power delay profile obtained by recording CDMA2000 forward channel signals during real-fieldmeasurements in various environments:mediumcity, flat terrain, and hilly terrain in northern Poland.The results of measurements are compared with characteristic parameters...
-
Calculation of the propagation loss in urban radio-access systems
PublicationZweryfikowano eksperymentalnie modele propagacyjne opracowane dla telefonii komórkowej w mieście, stosowane przy analizach projektowych systemów dostępowych. Przeprowadzono obszerne badania pomiarowe i zebrano prawie 19 tys. pomiarów. Na tej podstawie, stosując wielowymiarową analize regresji oraz zaproponowaną charakterystykę propagacyjną radiowych łączy dostępowych, opracowano nowy wielowariantowy model propagacyjny przeznaczony...
-
Characterization of Slow and Fast Fading in Off-Body Communication at 2.45 GHz with Space Diversity Scheme in an Indoor Environment
PublicationThe characterization of slow and fast fading in wireless body area networks with space diversity scheme has been presented. The analysis, based on the measurements at 2.45 GHz in an indoor environment, has shown that for all investigated configurations of receiving wearable antennas, the correlation coefficient values of the received signals’ parameters are below the assumed value of 0.5, being close to zero for the vast majority...
-
Measurement Stand and Methodology for Research of the Off-Body and Body-to-Body Radio Channels in WBANs with Different Diversity Schemes
PublicationThe concept of an experimental test bed for system loss and channel impulse response measurements for off-body and body-to-body radio channels in wireless body area networks (WBANs) is fully described. The possible measurement scenarios that may occur in investigation of off-body and body-to-body channels are classified and described in detail. Additionally, an evaluation is provided of the standard and expanded uncertainties of...
-
Communication Model Order Reduction in Hybrid Methods Involving Generalized Impedance Matrix
PublicationA novel strategy for the efficient analysis of frequency-domain scattering electromagnetic problems in open and closed domains is presented. A fully automatic model-order reduction technique, called the enhanced reduced-basis method, is applied to increase the efficiency of the hybrid approach, which combines the finite-element and mode-matching methods. Numerical tests show that the proposed algorithm yields reliable and highly...
-
Calculation of Resonance in Planar and Cylindrical Microstrip Structures Using a Hybrid Technique
PublicationA hybrid technique was employed for the analysis of the resonance frequency of thin planar and cylindrical microstrip structures with the patches of arbitrary geometry. The proposed technique utilizes a combination of Galerkin’s moment method and a finite-element method (FEM). In this approach, an FEM is adopted to calculate the patch surface current densities, and a method of moments is utilized to calculate the resonance frequencies...
-
Rapid simulation-driven design of miniaturised dual-band microwave couplers by means of adaptive response scaling
PublicationOne of the major challenges in the design of compact microwave structures is the necessity of simultaneous handling of several objectives and the fact that expensive electromagnetic (EM) analysis is required for their reliable evaluation. Design of multi-band circuits where performance requirements are to be satisfied for several frequencies at the same time is even more difficult. In this work, a computationally efficient design...
-
Analytical Expression for the Time-Domain Green's Function of a Discrete Plane Wave Propagating in the 3-D FDTD Grid
PublicationIn this paper, a closed-form expression for the time-domain dyadic Green’s function of a discrete plane wave (DPW) propagating in a 3-D finite-difference time-domain (FDTD) grid is derived. In order to verify our findings, the time-domain implementation of the DPW-injection technique is developed with the use of the derived expression for 3-D total-field/scattered-field (TFSF) FDTD simulations. This implementation requires computations...
-
Efficient Complex Root Tracing Algorithm for Propagation and Radiation Problems
PublicationAn efficient complex root tracing algorithm for propagation and radiation problems is presented. The proposed approach is based on a discretization of Cauchy’s Argument Principle and its generalization to the C × R space. Moreover, an engagement of the tracing process with a global root finding algorithm recently presented in the literature is performed. In order to confirm a validity and efficiency of the proposed technique, a...
-
Bandwidth-size design trade-offs for compact spline-parameterised patch couplers by means of electromagnetic-driven multi-objective optimisation
PublicationBroad bandwidth and small size are the key performance figures for contemporary microwave couplers. These requirements are conflicting, i.e. improvement of one generally leads to degradation of the other assuming fixed topology of the circuit at hand. From a designer's perspective, the knowledge about available design trade-offs is indispensable as it permits for tailoring the circuit for particular applications as well as comparing...
-
Variable-fidelity response feature surrogates for accelerated statistical analysis and yield estimation of compact microwave components
PublicationAccounting for manufacturing tolerances is an essential part of a reliable microwave design process. Yet, quantification of geometry and/or material parameter uncertainties is challenging at the level of full-wave electromagnetic (EM) simulation models. This is due to inherently high cost of EM analysis and massive simulations necessary to conduct the statistical analysis. Here, a low-cost and accurate yield estimation procedure...