Filtry
wszystkich: 1798
wybranych: 1399
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: PLATE HEAT EXCHANGER
-
Electrohydrodynamic Secondary Flow and Particle Collection Efficiency in a One-sided Spike-plate Type Electrostatic Precipitator
PublikacjaIn this work, results of electrohydrodynamic secondary flow and particle collection efficiency measurements in an electrostatic precipitator under positive and negative voltage polarity are presented. The electrostatic precipitator had two plate collecting electrodes and a single spike discharge electrode. The spike tips were only on one side of the discharge electrode, therefore called a one-sided spike electrode. The electrohydrodynamic...
-
Theoretical and experimental analysis of guided wave propagation in plate-like structures with sinusoidal thickness variations
PublikacjaGuided waves have attracted significant attention for non-destructive testing (NDT) and structural health monitoring (SHM) due to their ability to travel relatively long distances without significant energy loss combined with their sensitivity to even small defects. Therefore, they are commonly used in damage detection and localization applications. The main idea of incorporating guided waves in NDT and SHM is based on processing...
-
Effect of asymmetric fluid flow distribution on flow boiling in a microchannel heat sink – An experimental investigation
PublikacjaFlow boiling in microchannels is emerging as an exclusive cooling solution for miniaturized high-power electronic devices alongside having other high heat flux applications. Size miniaturization at microscale strangely increases heat transfer performance as well as flow boiling instabilities. Many flow boiling instabilities are interrelated and result from imperfect hydrodynamic conditions. One of such problems is flow maldistribution among...
-
Analysis of Organic Rankine Cycle efficiency and vapor generator heat transfer surface in function of the reduced pressure
PublikacjaIn the paper presented is analysis of the influence of reduced pressure on efficiency and heat transfer area of vapor generator of Organic Rankine Cycle (ORC) in case of subcritical and supercritical parameters of operation. Compared are two cases of subcritical and supercritical ORC featuring a similar arrangement of heat source supply and heat removal, that is featuring the same temperatures of working fluid before the turbine,...
-
Active Damping of Impulse-Excited Flexible Plate Vibration
PublikacjaArtykuł prezentuje metodę aktywnego tłumienia drgań podatnej płytki wzbudzanych impulsowo. Układ sterowania składa się z aktywych wzbudników piezoelektrycznych przymocowanych do przedmiotu. Efektywnośc metody została potwierdzona badaniami eksperymentalnymi.
-
Modeling of damage in a circular plate subjected to dynamic excitation
PublikacjaSzereg różnych dziedzin nauki zajmuje się problemem zniszczenia ciśnieniowych metalowych zbiorników (mechanika, termodynamika, mechanika płynów). Tylko niektóre prace ujmują wszystkie aspekty analizy. W prezentowanej pracy przedstawiono numeryczna analizę metalowej płyty poddanej obciążeniu dynamicznemu, aż do momentu zniszczenia. Do analizy zastosowano program MSC.Marc, element powłokowy, i prawo sprężysto lekoplastyczne uwzględniające...
-
RMS-based damage identification in adhesive joint between concrete beam and steel plate using ultrasonic guided waves
PublikacjaAdhesive joints have numerous applications in many branches of industry, such as civil engineering, automotive, aerospace and shipbuilding. As with most structural elements, adhesive joints can experience any damage mechanism, which induces the need for diagnostic testing. Ultrasonic waves are widely used for non-destructive inspection of many structures and their elements, including adhesive joints. Guided wave propagation method...
-
Experiment-Based Study of Heat Dissipation from the Power Cable in a Casing Pipe
PublikacjaThe paper deals with the important challenges in terms of electricity transmission by means of underground cable lines. The power cable’s performance is characterized by an ampacity that represents its maximum electric current-carrying capacity. The ampacity of power cables depends on their ability to diffuse the heat generated by the current flow into the environment. In the performed research, the analysis of the efficiency of...
-
Turbulent heat transfer in thin liquid films at low and high heat fluxes
PublikacjaW pracy przedstawiono rozważania turbulentnej wymiany ciepła w cienkich filmach cieczowych powstałych w wyniku uderzenia strugi przy małych i dużych strumieniach ciepła. W ostatnim przypadku może dojść do wrzenia filmu cieczowego. Oba zjawiska zamodelowano i uzyskano odpowiednie rozkłady temperatury i pedkosci.
-
Prediction of flow boiling heat transfer coefficient for carbon dioxide in minichannels and conventional channels
PublikacjaIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of carbon dioxide. The experimental data from various resea rches were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house model. The results show the importance of taking into...
-
Analysis of possibility and purposefulness of application of waste-heat boilers to trailing suction hopper dredgers
PublikacjaThis paper presents an analysis of possibility and purposefulness of application of waste-heat boilers to trailing suction hopper dredgers. Using results of own operational research on dredgers this author determined thermal power demand for six hypothetical trailing suction hopper dredgers of various size, at accounting for a type of power system and kind of fuel combusted by dredger's power plant. By means of basic indices of...
-
An enhanced method in predicting tensile behaviour of corroded thick steel plate specimens by using random field approach
PublikacjaThe present work investigates the possibility of using random field techniques in modelling the mechanical behaviour of corroded thick steel plate specimens. The nonlinear Finite Element method, employing the explicit dynamic solver, is used to analyse the mechanical properties of typical specimens. A material model considering full nonlinearity is used to evaluate the stress-strain response. The influence of major governing parameters...
-
A new method for determination of flow boiling heat transfer coefficient in conventional diameter channels and minichannels
PublikacjaW pracy przedstawiono rozważania związane z modelowaniem wrzenia w przepływie w kanałach o średnicach konwencjonalnych, małych i minikanałach. Przedstawiono przegląd podejść do modelowania wymiany ciepła i w tym świetle przedstawiono oryginalne podejście autora. W przeciwieństwie do innych podejść metoda autora ma zastosowanie zarówno do kanałów o średnicach konwencjonalnych i minikanałach. Przedstawiono zadowalające porównania...
-
Experimental Investigation of Free Convection Heat Transfer from Horizontal Cylinder to Nanofluids
PublikacjaThe results of free convection heat transfer investigation from a horizontal, uniformly heated tube immersed in a nanofluid are presented. Experiments were performed with five base fluids, i.e., ethylene glycol (EG), distilled water (W) and the mixtures of EG and water with the ratios of 60/40, 50/50, 40/60 by volume, so the Rayleigh (Ra) number range was 3 104 Ra 1.3 106 and the Prandtl (Pr) number varied from 4.4 to 176....
-
Promising Nanoparticle-Based Heat Transfer Fluids—Environmental and Techno-Economic Analysis Compared to Conventional Fluids
PublikacjaProviding optimal operating conditions is one of the major challenges for effective heating or cooling systems. Moreover, proper adjustment of the heat transfer fluid is also important from the viewpoint of the correct operation, maintenance, and cost efficiency of these systems. Therefore, in this paper, a detailed review of recent work on the subject of conventional and novel heat transfer fluid applications is presented. Particular...
-
Influence of Cement Replacement with Sewage Sludge Ash (SSA) on the Heat of Hydration of Cement Mortar
PublikacjaThe amount of fly ash from the incineration of sewage sludge is increasing all over the world, and its utilization is becoming a serious environmental problem. In the study, a type of sewage sludge ash (SSA) collected directly from the municipal sewage treatment plant was used. Five levels of cement replacement (2.5%, 5%, 7.5%, 10% and 20%) and unchanged water-to-binder (w/b) ratio (0.55) were used. The purpose of the study was...
-
Buckling analysis of piezo-magnetoelectric nanoplates in hygrothermal environment based on a novel one variable plate theory combining with higher-order nonlocal strain gradient theory
PublikacjaIn the present investigation, a new first-order shear deformation theory (OVFSDT) on the basis of the in-plane stability of the piezo-magnetoelectric composite nanoplate (PMEN) has been developed, and its precision has been evaluated. The OVFSDT has many advantages compared to the conventional first-order shear deformation theory (FSDT) such as needless of shear correction factors, containing less number of unknowns than the existing...
-
A semi-empirical model for flow boiling heat transfer with account of the reduced pressure effect
PublikacjaIn the present study the attention was focused on the influence of reduced pressure on the predictions of heat transfer during flow boiling at the extensive range of pressures. The results of calculations were to test the sensitivity of the in-house flow boiling model with respect to the selection of the appropriate two-phase flow multiplier, which is one of the distinctive elements of that model. For this purpose a few two-phase...
-
Heat recovery from the hybrid photovoltaic tile – experimental studies with the solar light simulator
PublikacjaConsidering the current development of micro-cogeneration energy sources, supported by the national prosumer policy and the act on the renewable energy sources, there is a great demand for the effective solar technologies. In this area, the photovoltaic cells with a combined conversion of the solar radiation energy into the electrical and thermal energy (PV/T cells) seem to be attractive. They are already widely available and treated...
-
Comparison of heat transfer characteristics in surface cooling using microjets with water, ethanol and HFE7100 as test fluids
PublikacjaAccurate control of cooling parameters is required in ever wider range of technical applications. It is known that reducing the dimensions of the size of nozzle leads to an increase in the economy of cooling and improves its quality. Present study describes research related to the design and construction of the nozzles and microjet study, which may be applied in many technical applications such as in metallurgy, electronics, etc....
-
Effect of tube bundle arrangement on performance of shell-and-tube latent heat storage system
PublikacjaThis work presents the results of experimental investigation on charging and discharging of latent heat storage systems (LHSS) in the form of shell-and-tube heat exchangers with a variable arrays of the tube bundles. The tests included two tube arrangements – in-line and triangular (staggered), a variable number of tubes in a bundle, two pitch ratios, and different tube positions in a bundle. Three commercial products (LTP56, RT54HC,...
-
Heat transfer intensification by jet impingement – numerical analysis using RANS approach
PublikacjaJet impingement is a method of the heat transfer enhancement applied in the engineering systems. The idea is to generate fast-flow fluid jet which impinge on the heated (or cooled) surface, causing significantly higher heat transfer rate. Although some flat surface jet impingement cases are described in the literature, the validated data is still limited. The reason is coming from the fact, that these flows are hydrodynamically...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaNanofluids came to be seen as a new generation of coolants, especially in single-phase systems. Conducted experiments indicate that the increase in thermal conductivity is not the only reason for the intensification of heat transfer when using nanofluids. Preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter...
-
Modelling study of flow boiling heat transfer of perspective fluids for refrigeration technology
PublikacjaThere is a gap of knowledge on flow boiling at high saturation temperatures and higher values of reduced pressure. Thus far, the in-house developed semi-empirical model for flow boiling and flow condensation showed a satisfactory accuracy for calculations for various refrigeration fluids for a wide scope of reduced pressures. This study presents results of calculations of heat transfer coefficient of perspective refrigeration fluids,...
-
Computational analysis of power-law fluids for convective heat transfer in permeable enclosures using Darcy effects
PublikacjaNatural convection is a complex environmental phenomenon that typically occurs in engineering settings in porous structures. Shear thinning or shear thickening fuids are characteristics of power-law fuids, which are non-Newtonian in nature and fnd wide-ranging uses in various industrial processes. Non-Newtonian fuid fow in porous media is a difcult problem with important consequences for energy systems and heat transfer. In this...
-
Impact of Temperature and Nanoparticle Concentration on Turbulent Forced Convective Heat Transfer of Nanofluids
PublikacjaTheoretical analysis of the influence of nanoparticles and temperature on the average Nusselt (Nu) number and the average heat transfer coefficient (HTC) during the turbulent flow of nanofluid in a horizontal, round tube was carried out. The Nu number is a function of the Reynolds (Re) number and the Prandtl (Pr) number, which in turn are functions of the thermophysical properties of the liquid and the flow conditions. On the other...
-
Impact of the inclination angle of the condenser with refrigerant R410A on heat transfer coefficient – experimental study
PublikacjaIn the paper the authors present results of a laboratory test of the condenser with refrigerant R410A. The effect of the inclination of this condenser on the heat transfer coefficient value has been considered. The test has proved that there is an optimal inclination angle of the condenser which gives maximal value of this coefficient.
-
Additive Manufacturing as a Solution to Challenges Associated with Heat Pipe Production
PublikacjaThe aim of this review is to present the recent developments in heat pipe production, which respond to the current technical problems related to the wide implementation of this technology. A novel approach in HP manufacturing is to utilise hi-tech additive manufacturing techniques where the most complicated geometries are fabricated layer-by-layer directly from a digital file. This technology might be a solution to various challenges...
-
Effect of Tube Bundle Arrangement on the Performance of PCM Heat Storage Units
PublikacjaThe results of comprehensive study on charging and discharging of latent heat storage systems (LHSS) are presented. The multi tube shell-and-tube unit with a variable layouts of the tube bundles are examined. Two tube arrangements – in-line and staggered are tested. A variable number of tubes and different tube positions in a bundle are investigated. Moreover, two pitch ratios are studied. Three commercially available substances...
-
Heat generation by impulse ultrasound.
PublikacjaOryginalna metoda zastosowana dla wyprowadzenia równaniaewolucyjnego dla ogrzewania środowiska przez falę akustycznądowolnej natury, w tym nieokresowej. Przedstawiono przykłady obliczeń numerycznych.
-
The effect of reduced pressure on carbon dioxide flow boiling heat transfer in minichannels
Publikacja. In the paper presented are the results of the study on the effect of reduced pressure on flow boiling heat transfer data in minichannels as well as conventional ones. That effect renders that most of heat transfer correlations fail to return appropriate results of predictions. Mostly they have been developed for the reduced pressures from the range 0.1-0.3. The special correction has been postulated to the in-house model of flow...
-
Study of the Influence of Heat Convection Coefficient on Predicted Performance of a Large Tilting-Pad Thrust Bearing
PublikacjaPart of the heat generated by the shearing of the lubricating film during operation of a hydrodynamic bearing is transferred to the bearing components. In the case of the pad, which is usually fully submerged in the lubricating oil, heat is further transferred at the pad free walls to the oil by convection. This mechanism causes a thermal gradient in a pad and, consequently, its thermal deflection. In large hydrodynamic thrust...
-
Comparitive study of heat transfer and pressure drop during flow boiling and flow condensation in minichannels
PublikacjaIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for flow boiling and also flow condensation for some recent data collected from literature for such fluids as R404a, R600a, R290, R32,R134a, R1234yf and other. The modification of interface shear stresses between flow boiling and flow condensation in annular flow structure are considered through incorporation...
-
The Use of Liquid Crystal Thermography an Image Processing in Heat and Fluid-Flow Research
PublikacjaLiquid crystal thermography (LCT) have been used in many technical, industrial and biomedical applications [1]. During over 20 years it has been successfully applied in Department of Energy and Industrial Apparatus at Gdansk University of Technology for visualization of steady-state and transient temperature fields. In order to demonstrate feasibility of LCT techniques in practical heat transfer contexts, the authors have performed...
-
Preliminary results from HEDGEHOG REXUS project – A sounding rocket experiment on accelerations, vibrations and heat flow
PublikacjaDuring flight, a sounding rocket is subject to a unique environment - severe vibrations and substantial heat flux. In order to design payloads, precise measurement of these conditions is required. This paper presents preliminary results from HEDGEHOG REXUS Project, whose scientific goal was to characterise the thermal and dynamic environment of REXUS sounding rockets. For this purpose, two new sensors have been designed - mechanical...
-
Comparison of traditional district heating with low temperature district heating systems featuring organic Rankine cycle and heat pump
PublikacjaPaper presents a comparison between a traditional district heating system with conventional boilers as a source of heat and electricity purchases from power utilities and a low temperature DH system incorporating the CHP with organic Rankine Cycle providing electricity and local heat pump raising the temperature of the DH fluid to the required temperature in the dwelling, meaning that both heat and electricity are produced within...
-
Use of the Delta plate for surgical treatment of patients with condylar fractures
Publikacja -
Secondary Thermal Deformation Characteristics of Stiffened Plate Exposed to Fire
Publikacja -
Spectral plate element for crach detection with use of propagation wares.
PublikacjaW pracy przedstawiono model płyty oparty na metodzie elementów spectralnych. Przedstawiono wyniki analizy interakcji pęknięcia zmęczeniowego i propagującej się fali.
-
Stable and unstable bifurcation in the von Karman problem for a circular plate
PublikacjaW niniejszej pracy badamy równania von Karmana dla cienkiej, sprężystej, kołowej płyty, która znajduje się na sprężystym podłożu, pod działaniem sił ściskających wzdłuż swojego brzegu.Stosując metody analizy nieliniowej, dowodzimy istnienia stabilnychi niestabilnych punktów bifurkacji w zbiorze rozwiązań badanych równań.
-
Numerical solution analysis of fractional point kinetics and heat exchange in nuclear reactor
PublikacjaThe paper presents the neutron point kinetics and heat exchange models for the nuclear reactor. The models consist of a nonlinear system of fractional ordinary differential and algebraic equations. Two numerical algorithms are used to solve them. The first algorithm is application of discrete Grünwald-Letnikov definition of the fractional derivative in the model. The second involves building an analog scheme in the FOMCON Toolbox...
-
Numerical simulation of temperature distribution of heat flow on reservoir tanks connected in a series
PublikacjaThe flow of temperature distribution through a medium in thermodynamic studies plays an important role in understanding physical phenomena in chemical science and petroleum engineering, while temperature distribution indicates the degree of reaction that must be undergone to obtain the final product. Therefore, this paper aims to present and apply the exponential matrix algorithm (EMA), differential transformation algorithm (DTA),...
-
Numerical analysis of the two‐phase steam‐air heat transfer flow induced in smooth and corrugated channel using the VOF model
Publikacja -
Utilisation of bleed steam heat to increase the upper heat source temperature in low-temperature ORC
PublikacjaW pracy przedstawiono możliwość dogrzewu obiegu ORC za pomocą pary upustowej.
-
A model of combined heat and power generating plant with urban heat distribution network for production scheduling
PublikacjaPoruszono zagadnienie związane z pracowaniem harmonogramu produkcji elektrociepłowni. Uwzględniony został wpływ zachowania się miejskiej sieci ciepłowniczej na pracę elektrociepłowni. Możliwe jest również modelowanie współpracy ze zbiornikiem ciepła.
-
Experimental investigation of M-shape heat transfer coefficient distribution of R123 flow boiling in small-diameter tubes
PublikacjaW publikacji przedstawiono wyniki badań wrzenia czynnika R123 w srebrnych rurkach o małych średnicach (średnice wewnętrzne wynosiły odpowiednio 1.15 mm i 2.3 mm). Badania przeprowadzono w szerokim zakresie stopnia suchości pary (0.01-0.9), gęstości strumienia masy (650-3000 kg/(m2s)) oraz gęstości strumienia ciepła (40-80 kW/m2). W badaniach wykazano, że istnieją dwa lokalne maksima współczynnika przejmowania ciepła w jego profilu...
-
A common method for calculation of flow boiling and flow condensation heat transfer coefficients in minichannels with account of nonadiabatic effects
PublikacjaW pracy przedstawiono metodę ogólną wyznaczania współczynników przejmowania ciepła podczas wrzenia w przepływie i kondensacji w przepływie w minikanałach z uwzględnieniem efektu nieadiabatycznego. Uwzględnia ona wpływ modyfikacji naprężeń stycznych na granicy ciecz-para na wymianę ciepła.
-
Numerical Study on Mitigation of Flow Maldistribution in Parallel Microchannel Heat Sink: Channels Variable Width Versus Variable Height Approach
PublikacjaMicrochannel heat sink on one hand enjoys benefits of intensified several folds heat transfer performance but on the other hand has to suffer aggravated form of trifling limitations associated with imperfect hydrodynamics and heat transfer behavior. Flow maldistribution is one of such limitation that exaggerates temperature nonuniformity across parallel microchannels leading to increase in maximum base temperature. Recently, variable...
-
Neural network simulator's application to reference performance determination of turbine blading in the heat-flow diagnostics.
PublikacjaIn the paper, the possibility of application of artificial neural networks to perform the fluid flow calculations through both damaged and undamaged turbine blading was investigated. Preliminary results are presented and show the potentiality of further development of the method for the purpose of heat-flow diagnostics.
-
Capillary pumped loop as a tool for collecting large heat fluxes from electronic devices on warships
PublikacjaThe combat potential of future warships will be directly related to the use of modern electronic devices being parts of advanced systems, such as, for instance, radar systems, fire aiming systems, fire detection systems, electric drive systems, and even electronic and radio-electronic weaponry, railguns and lasers, installed on these warships. The capacity and functionality of these devices is continually increasing, at decreasing...