Wyszukiwarka
Wyniki wyszukiwania dla: CIRCULAR SAW BLADE
-
Washboarding during cutting on frame sawing machines II. Experimental study of the saw blade behaviour
PublikacjaPraca jest swego rodzaju suplementem do referatu przedstawianego na 15th Inernational Wood Machining Seminar w Los Angeles, CA, USA. Opisano uzyskane wyniki badań doświadczalnych prowadzonych w oparciu o plan badań Hartley`a.Czynnikami badanymi były: naprężenia napinające brzeszczotu piły, częstotliwość skoków ramy piłowej oraz wysokość cięcia przedmiotu obrabianego. Czynnikami wynikowymi były: wysokość sfalowania powierzchni oraz...
-
Geometrical conditions of saw blade`s entering into and going out of material during wood cutting
PublikacjaW pracy przedstawiono analizę geometrycznych warunków wejścia i wyjścia ostrza piły z materiału obrabianego przy przecinaniu drewna. Przedstawiono czasowy i przestrzenny rozkład geometrycznych parametrów wejścia i wyjścia ostrza i ich wpływ na trwałość ostrzy i dokładność przecinania.
-
[Chapter III] Influence of chip transport method on effects of cutting with circular saw
PublikacjaW pracy przedstawiono analizę transportu wiórów ze strefy skrawania na zewnątrz materiału obrabianego w procesie przecinania drewna piłami tarczowymi. Przedstawiono również przykłady zużycia pił tarczowych spowodowanych niewłaściwym transportem wiórów.
-
The critical rotational speed of circular saw: simple measurement method and its practical implementations.
PublikacjaProducenci pił tarczowych są zobligowani do podawania ich dopuszczalnych prędkości obrotowych. Jednakże, umieszczane przez nich prędkości na piłach są często bliskie prędkościom krytycznym lub je przewyższają. Przecinanie takimi narzędziami może być więc niebezpieczne dla obsługującego. Praca przedstawia prostą metodologię wyznaczania prędkości obrotowych krytycznych pił tarczowych. Badania były prowadzone z wykorzystaniem technik...
-
A method for measurements of geometry and positions of circular saw teethMetoda merania geometrie a polohy zubov v tele piloveho kotuca
PublikacjaW pracy przedstawiono sposób określania geometrii i położenia ostrzy piły tarczowej. Opisano metodę bazująca na numerycznej obróbce zarejestrowanych obrazów ostrzy pił w sposób automatyczny na automatycznym urządzeniu WKOPTar.
-
Mode vibrations of plates – experimental analysis
PublikacjaIn this paper results of the square MDF plate and circular saw blades examination with the use of the harmonic method to static identification of resonant frequencies and shapes of mode vibrations are presented. Obtained results reveled that for circular saws with large holes in a saw blade appeared two resonant frequencies for the same nodal number.
-
Theoretical and Actual Feed Per Tooth During Wood Sawing on an Optimizing Cross-Cut Saw
PublikacjaThe work presents the geometries of circular saw teeth, whose task is to divide the cross-cut of the cutting layer. For efficient machining on a cross-cut saw with high feed speed values (about 1 ms−1) maximal theoretical feeds per tooth are determined. These values were compared with the actual values determined during transverse cutting of pine wood on a special test stands in industrial conditions. In the experiment the rotational...
-
Experimental analysis of chip removing system in circular sawing machine
PublikacjaPaper presents analysis of the process of removing the wood chips generated during the cutting of the material on the circular sawing machine. The attention is focused on the upper cover of the chip removing system. Within the framework of the work a systematic experimental study of pressure distribution in the cover during operation of the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm was carried...
-
Optimization of chip removing system operation in circular sawing machine
PublikacjaThe paper presents the optimization of the wood chips removing system in the sliding table saw. Chips are generated during the cutting of the material. The attention was focused on the upper casing of mentioned system. The methodical experimental studies of the pressure distribution inside the casing during the wood chip removing operation for the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm were...
-
Application in circular sawing machines of the experimental results of investigations of the chip removing system operation
PublikacjaThe experimental results of the chip removing system operation are presented. The main aim of them was to optimize suction system of the panel saw Fx3 and its follower Fx550. The attention was focused on the upper casing, which was the part of removing system. Within the framework of the work a systematic experimental study of pressure distribution in the casing during operation of the selected rotational speed of saw blade with...
-
Chip suction system in circular sawing machine: empirical research and computational fluid dynamics numerical simulations
PublikacjaThe experimental analysis of the wood chip removing system during its redesigning in the existing sliding table circular saw and computational fluid dynamic (CFD) numerical simulations of the air flow process is presented in the paper. The attention was focused on the extraction hood and the bottom shelter of the actual existing system. The main aim was to perform experimental research on the pressure distribution inside the...
-
Numerical analysis of chip removing system operation in circular sawing machine using CFD software
PublikacjaPaper presents the analysis of the results of numerical simulations of the air flow process of wood chips removing system in the circular sawing machine. The attention is focused on the upper cover and bottom shelter of the chip removing system. Within the framework of the work a systematic numerical modeling of the air flow distribution in the cover and shelter during operation of the selected rotational speed of saw blade with...
-
Fracture Toughness and Shear Yield Strength Determination for Two Selected Species of Central European Provenance
PublikacjaWhen offcut of wood is formed by shearing, Atkins’s analyses of sawing processes can be applied. Using this modern approach, it is possible to determine the fracture toughness and shear yield strength of wood. This model is only applicable for the axial-perpendicular cutting direction because both of these parameters are suitable for the given direction of cutting edge movement and cannot be considered material constants. Alternatively,...
-
The effect of a belt position in the spindle driving system on critical rotational speeds
PublikacjaThe aim of this paper was to examine how the belt pulley position affects critical rotational speeds of the modernized spindle of the sliding table saw Fx3. Methodology of determination of critical rotational speeds of the spindle in a function of the spindle design features and its driving system is presented. Spindles in these kind of machine tools are mainly driven with V-belts, and the pulleys on the spindles might be positioned:...
-
CUTTING POWER FORECASTING WHILE WOOD SAWING: FRACTURE MECHANICS APPROACH AND AXELSSON’S MODEL COMPARISON
PublikacjaIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (power) could be considered from a point of view of modern fracture mechanics. Another way is to forecast cutting power consumption on...
-
The reduction of vibrations in circular sawing machines
PublikacjaThe presented in this paper the main objectives of the research were to explore vibrations signals of the main spindle system, the machine tool body and a circular saw to extract informative features for assessment of the designs of the panel saw Fx3 and its follower Fx550.Even though the main spindle of the new table sliding saw Fx550 has its rotational speeds larger about 20% in comparison to the Fx3, peak values of the vibrational...
-
Capacity of Surface Production of Band Sawing in Manufacture of Oak Floor Upper Layers
PublikacjaThin lamellae, corresponding to the layer components of structural glued members, i.e., 2-ply or 3-ply glued flooring, can be manufactured in re-sawing operations of kiln-dried wood blocks or in wet technologies, which currently seem to be more common because of the shorter drying time. The re-sawing process in wet technology is conducted on dedicated thin-cutting band sawing machines with stellite-tipped band saws. The goal of...
-
The Design Development of the Sliding Table Saw Towards Improving Its Dynamic Properties
PublikacjaCutting wood with circular saws is a popular machining operation in the woodworking and furniture industries. In the latter sliding table saws (panel saws) are commonly used for cutting of medium density fiberboards (MDF), high density fiberboards (HDF), laminate veneer lumber (LVL), plywood and chipboards of different structures. The most demanded requirements for machine tools are accuracy and precision, which mainly depend on...
-
Lateral forces determine dimensional accuracy of the narrow‑kerf sawing of wood
PublikacjaThe shrinking global forest area limits the supply of industrially usable raw resources. This, in combination with the ever‑increasing consumption of timber due to population growth can lead to the lack of a positive balance between the annual volumetric growth and consumption of wood. An important innovation toward increasing environmental and economic sustainability of timber production is to reduce the volume of wood residues...
-
Sawing Processes as a Way of Determining Fracture Toughness and Shear Yield Stresses of Wood
PublikacjaA new computational model, based on fracture mechanics, was used to determine cutting forces. Unlike traditional computing methods, which depend on many coefficients reflecting the machining of solid wood, the new model uses two main parameters: fracture toughness and shear yield stresses. The aim of this study was to apply this new method to determine these parameters for the tooth cutting edge principal positions and longitudinal...
-
Preliminary studies on the effect of feed speed on the colour change of wood
PublikacjaThis paper presents the results of preliminary analyses of the effect of cutting parameters on changes in the colour of wood. Beech wood cut with use circular saw was analysed. The cutting parameter tested was the feed speed, represented by the feed per tooth. Sawing processes with different feed per tooth ranging from 0.0008 mm to 0.09 mm were analysed. It was observed that over the entire range of feed rate per tooth analysed,...
-
Estimation of fracture toughness and shear yield stress of orthotropic materials in cutting with rotating tools
PublikacjaThe cutting force is an energetic effect of splitting material, and might be considered from a point of view of modern fracture mechanics. Forecasting of the shear plane angle in cutting broaden possibilities for modelling of the cutting process even for thin uncut chips. Such mathematical model has been developed here for description of the orthotropic materials’ cutting on the base of fracture theory, and includes work of separation...
-
SAWING PROCESS AS A NEW ALTERNATIVE WAY OF DETERMINING SOME WOOD PROPERTIES
PublikacjaCutting forces (power) could be considered from a point of view of modern fracture mechanics. The developed cutting model, derived from fracture mechanics, includes work of separation (fracture toughness) in addition to plasticity and friction, and also dullness of the cutting edge described by the cutting edge radius. Moreover, forecasting of the shear plane angle for the cutting models, broaden possibilities of energetic effects...
-
AN ALTERNATIVE WAY OF DETERMINING MECHANICAL PROPERTIES OF WOOD BY MEASURING CUTTING FORCES
PublikacjaThe cutting force is an energetic effect of splitting material, and might be therefore considered from a point of view of modern fracture mechanics. The dedicated mathematical model developed for description of the wood cutting has been developed here on the base of fracture theory, and includes work of separation (fracture toughness) in addition to the material plasticity and friction. The effect of the cutting edge dullness is...
-
Cutting model parameters from frame sawing of natural and impregnated Scots pine (Pinus sylvestris L.)
PublikacjaIn this paper, absolute and density normalized cutting model parameters of natural and impregnated Scots pine (Pinus sylvestris L.) are shown and a method for the calculation of their corresponding material properties in the principal material directions of wood is presented. The parameters were determined from measurements of cutting power on a sash gang saw, and are in detail the fracture toughness and the shear yield strength...
-
Blade Section Prpfile Array Lifting Surface Design Method for Marine Screw Propeller Blade
PublikacjaThe lifting surface model is widely used in screw propeller design and analysis applications. It serves as a reliable tool for determination of the propeller blade mean line and pitch distribution. The main idea of this application was to determine the blade shape that would satisfy the kinematic boundary condition on its surface with the prescribed bound circulation distribution over it. In this paper a simplified lifting surface...
-
Process Engineering in Circular Economy
Kursy OnlineKurs jest przeznaczony dla doktorantów szkoły doktorskiej w dyscyplnach: inżynieria lądowa i transport (SzD), III stopnia, stacjonarne inżynieria środowiska, górnictwo i energetyka (SzD), III stopnia, stacjonarne The course is addressed to PhD students of the doctoral school in disciplines: civil engineering and transport environmental engineering, mining and power engineering Course type: lecture Total hours of...
-
Process engineering in circular economy
Kursy OnlineDefinition and principles of the circular economy (CE). The transition from a linear model to a circular model. Business models for the CE. Circular design and innovation. CE assessment carbon footprint, life cycle assessment. Case studies of the cities implementing the CE concept. CE policy and legislation (EU and Poland). Wastewater treatment plants as an element of the CE. Energy and nutrient recovery technologies in wastewater...
-
A Method for Optimising the Blade Profile in Kaplan Turbine
PublikacjaThis paper introduces a method of blade profile optimisation for Kaplan-type turbines, based on modelling the interaction between rotor and stator blades. Rotor and stator blade geometry is described mathematically by means of a midline curve and thickness distribution. Genetic algorithms are then used to find a global optimum that minimises the loss coefficient. This allows for variety of possible blade shapes and configurations....
-
Process engineering in circular economy 22/23
Kursy OnlineBackground of the circular economy What is the circular economy? (Definition) How is the circular economy different from a linear economy? How do materials circulate in the circular economy? The circular economy and sustainable development How to measure circularity? Link between the circular economy and life cycle assessment (LCA) What are the benefits of the circular economy? The circular economy policies and governance Wastewater...
-
Improving Savonius rotor performance by shaping its blade edges
PublikacjaThe article presents the results of the numerical analysis of the flow inside the Savonius rotor. Particular at-tention has been paid to the vicinity of the blade gap in order to recognise the mechanisms controlling the flow in this area. The conclusions resulting from the analysis made the basis for an attempt to improve Savonius turbine performance via shaping rotor blade edges. The paper presents selected characteristic flow...
-
Rotor Blade Geometry Optimisation in Kaplan Turbine
PublikacjaThe paper presents the description of method and results of rotor blade shape optimisation. The rotor blading constitutes a part ofturbine flow path. Optimisation consists in selection of the shape that minimises ratio of polytrophic loss. Shape of the blade isdefined by the mean camber line and thickness of the airfoil. Thickness is distributed around the camber line based on the ratio ofdistribution. Global optimisation was done...
-
Circular Farmaceutica
Czasopisma -
[ILiT, IŚGiE] Process engineering in circular economy - Nowy
Kursy OnlineKurs jest przeznaczony dla doktorantów szkoły doktorskiej w dyscyplnach: inżynieria lądowa i transport (SzD), III stopnia, stacjonarne inżynieria środowiska, górnictwo i energetyka (SzD), III stopnia, stacjonarne The course is addressed to PhD students of the doctoral school in disciplines: civil engineering and transport environmental engineering, mining and power engineering Course type: lecture Total hours of...
-
Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests
PublikacjasettingsOrder Article Reprints Open AccessArticle Suitableness of SLM Manufactured Turbine Blade for Aerodynamical Tests by Janusz Telega 1,*ORCID,Piotr Kaczynski 1ORCID,Małgorzata A. Śmiałek 2ORCID,Piotr Pawlowski 3ORCID andRyszard Szwaba 1ORCID 1 Institute of Fluid Flow Machinery Polish Academy of Sciences (IMP PAN), Fiszera 14, 80-231 Gdansk, Poland 2 Faculty of Mechanical Engineering and Ship Technology, Institute of Naval...
-
Analysis of the design development of the sliding table saw spindles
PublikacjaProducers of sliding table saws constantly strive for improvement in sawing accuracy. One of the method is an upswing in a spindle behavior, since, it affects to a large degree sawing effects. The design development of sliding table saw spindles during the last quarter-century is presented. The spindle system of the modernized spindle of the sawing machine Fx550 is described.
-
Application of Rapid Prototyping technology in the manufacturing of turbine blade with small diameter holes
PublikacjaThe article presents the possibilities of using Rapid Prototyping (RP) technology in the manufacturing of turbine blades with small diameter holes. The object under investigation was gas turbine blade with small diameter cooling holes and holes for generating longitudinal vortices. A turbine blade model was produced by means of Direct Metal Laser Sintering (DMLS) technology and subsequently validated in terms of detection and accuracy...
-
Assessment of damage causes of a 17 m long wind turbine blade model
PublikacjaThe subject matter is to verify the stiffness of the steel supporting structure and assess the causes of cracks in the 17 m long wind turbine blade model
-
EMPIRICAL ASSESMENT OF THE MAIN DRIVING SYSTEM OF THE CIRCULAR SAWING MACHINE
PublikacjaThe producers of panel saws tend to improve sawing accuracy and minimise a level of vibrations, to increase their competitiveness at the market. Mechanical vibrations in the main saw driving system, which level depend on a plethora independent factors, may really affect sawing accuracy and general machine tool vibrations. The objective of the research was to explore vibrations signals of the main spindle system, and to extract...
-
ICT-enabled circular economy: conceptualising the links
PublikacjaThis chapter sets conceptual backgrounds regarding the potentially emerging causal links between digital technologies and circular economy ideas implementation. We argue that digital technologies may constitute an effective element enabling the transformation from linear to circular and environmentally friendly economic activities. This work draws the general picture at the macro and micro level. The macro perspective shows how...
-
[ILiT, IŚGiE] Process engineering in circular economy 20/21 Summer
Kursy OnlineKurs jest przeznaczony dla doktorantów szkoły doktorskiej w dyscyplnach: inżynieria lądowa i transport (SzD), III stopnia, stacjonarne inżynieria środowiska, górnictwo i energetyka (SzD), III stopnia, stacjonarne The course is addressed to PhD students of the doctoral school in disciplines: civil engineering and transport environmental engineering, mining and power engineering Course type: lecture Total hours of...
-
Analysis of Modal Parameters Using a Statistical Approach for Condition Monitoring of the Wind Turbine Blade
PublikacjaThe primary objective of the presented paper is the numerical and experimental investigation related to developing a useful diagnostic method, which can be used for determining the site and size of damage in laminated shells of wind turbine blades. The described detection technique is based on the analysis of low frequencies bending vibrations mode shapes of rotor blades. The authors used the commonly applied statistics methods...
-
Wpływ nawodorowania na odporność korozyjną stali superdupleks spawanej metodą SAW
PublikacjaW pracy przedstawiono wyniki badań metodą potencjodynamiczną odporności korozyjnej złączy ze stali superdupleks wykonanych procesem SAW. Ustalono, że największą wrażliwością na korozję charakteryzuje się spoina.
-
Updating Finite Element Model of a Wind Turbine Blade Section Using Experimental Modal Analysis Results
PublikacjaThis paper presents selected results and aspects of themultidisciplinary and interdisciplinary research oriented for the experimental and numerical study of the structural dynamics of a bend-twist coupled full scale section of awind turbine blade structure.Themain goal of the conducted research is to validate finite elementmodel of themodified wind turbine blade section mounted in the flexible support structure accordingly to the...
-
Damage Detection in the Wind Turbine Blade Using Root Mean Square and Experimental Modal Parameters
PublikacjaThe paper presents results of an experimental study related to a non-destructive diagnostic technique used for preliminary determination the location and size of delamination in composite coatings of wind turbine blades. The proposed method of damage detection is based on the analysis of the ten first mode shapes of bending vibrations, which correspond to displacements of rotor blades perpendicular to the rotor plane. Modal parameters...
-
Experimental examination and modification of chip suction system in circular sawing machine
PublikacjaThe article presents the results of experimental examination of the wood chip suction system in the existing sliding table saw before and after its modifi cation. The studies focused on the extraction hood of the mentioned system. The methodical experimental research of the pressure distribution inside the hood during wood chip removal for the selected rotational speed of saw blades of 3500 and 6000 min-1 with a diameter of 300...
-
T-colorings, divisibility and circular chromatic number
PublikacjaLet T be a T-set, i.e., a finite set of nonnegative integers satisfying 0 ∈ T, and G be a graph. In the paper we study relations between the T-edge spans espT (G) and espd⊙T (G), where d is a positive integer and d ⊙ T = {0 ≤ t ≤ d (max T + 1): d |t ⇒ t/d ∈ T} . We show that espd⊙T (G) = d espT (G) − r, where r, 0 ≤ r ≤ d − 1, is an integer that depends on T and G. Next we focus on the case T = {0} and show that espd⊙{0} (G) =...
-
Stiffness assessment of the laminate recovered from end-of-life wind turbine blade
PublikacjaIn the paper the stiffness parameters of the laminate recovered from an aerodynamic shell of a decommissioned wind turbine blade are evaluated. The aim of the work is to assess selected methods for identifying material data, as well as to estimate the level of stiffness degradation during turbine operation. Several practical identification methods are presented and compared. Two concepts of a single laminate layer are considered,...
-
Influence of electrode geometric arrangement on the operation of narrow circular electrostatic precipitator
PublikacjaIn this work the influence of electrode geometric arrangement on the operation of a circular electrostatic precipitator (ESP) was investigated using Particle Image Velocimetry (PIV) method. The ESP was a glass circular cylinder (29 mm in diameter, 300 mm long) equipped with a wire discharge electrode and circular-cylinder collecting electrode. The stainless-steel discharge wire electrode (0.23 mm in diameter, 100 mm long) was mounted...
-
Modeling by finite element methods of impact of erosion on frequency of normal modes of L-0 blade
PublikacjaAfter some time of exploitation steam turbine rotors blades in energetic industry they are being eroded and also their frequency of normal modes is changed. Those changes can cause to unwanted shift of blades normal mode frequencies. It is necessary to find quick method of rating changes of frequency in connection of mass loss due erosion. The evaluation of this dependence was made by finite element modeling method using HyperWorks...