Wyniki wyszukiwania dla: FORCED CONVECTIVE HEAT TRANSFER
-
Verification of the method of reconstructing convective velocity fields on the basis of temperature fields in vertical, differential and equally heated, open and closed channels
PublikacjaThis paper describes a method of reconstructing velocity fields, i.e. a numerical reconstruction procedure (NRP) that involves the numerical processing of experimentally measured temperature distributions in free convection heat transfer. The NRP consists in solving only the continuity and Navier–Stokes equations with an additional source term. This term is proportional to a known temperature (e.g. from a thermal imaging camera)...
-
Heat transfer and pressure drop during flow boiling of refrigerant/oil mixture inside smooth tube
PublikacjaW pracy przedstawiono wyniki badań współczynnika przejmowania ciepła i spadku ciśnienia podczas wrzenia czystych oraz zaolejonych czynników chłodniczych (R22, R134a, R407C) wrzących w poziomej stalowej rurce.
-
Heat transfer during pool boiling of water, methanol and R141b on porous coated horizontal tube bundles
PublikacjaPrzedstawiono wyniki badań eksperymentalnych wrzenia wody, metanolu i R141b na poziomym pęczku rur pokrytych metaliczna powłoką porowatą. Badania przeprowadzono dla podziałek rur 1.7d oaz 2d, przy ciśnieniu atmosferycznym i podciśnieniu.
-
Experimental and Computational Fluid Dynamics Studies on Straight and U-Bend Double Tube Heat Exchangers with Active and Passive Enhancement Methods
PublikacjaIn this work, the authors wanted to demonstrate the possibility to increase the heat transfer efficiency by using simple wire coil inserts to create turbulent flow in the boundary layer as well as air blowing into the annulus of the pipe. Experimental investigations were carried out for four heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend double tube, U-tube with turbulator, plain double...
-
Experimental validation of the theoretical analysis of heat transfer between a liquid layer formed by an impinging jet and a solid surface
PublikacjaPrzedstawiono wyniki badań eksperymentalnych wymiany ciepła między poziomą powierzchnią a przepływająca po niej warstwa cieczy utworzoną z napływającej strugi gazowo-cieczowej. Wyniki badań eksperymentalnych porównano z modelem teoretycznym zjawiska.
-
Investigation of the flow, heat and mass transfer and emissions in pulverized fuel fired boiler using physical and numerical modeling.
PublikacjaPraca przedstawia wykorzystanie techniki modelowania fizycznego trójwymiarowego oraz obliczeń numerycznych umożliwiających symulację rzeczywistych procesów spalania paliw stałych i gazowych w urządzeniach energetycznych. Dodatkowo wyniki obliczeń porównano z wynikami modelowania fizycznego oraz pomiarów na obiekcie rzeczywistym.
-
A semi-empirical method for calculation of flow boiling heat transfer coefficients for conventional channels and small diameter tubes
PublikacjaW pracy przedstawiono rozważania na temat modelowania dwufazowego przepływu wrzącego w kanałach konwencjonalnych i w kanałach o małej średnicy. Przedstawiono modyfikację korelacji zaproponowanej wcześniej przez J. Mikielewicza na podstawie nowych danych eksperymentalnych, uzyskanych dla kanałów o małej średnicy. Bank danych obejmował ponad 460 punktów pomiarowych dla czynników R141b, R134a, R113, R123, R12, R11 i wody. Uzyskano...
-
Non-isothermal effects in a common method for calculation of heat transfer coefficient in flow boiling and flow condensation in minichannels
PublikacjaW pracy przestawiono efekty nieizotermiczne w metodzie wyznaczania współczynnika przejmowania ciepła podczas wrzenia w przepływie oraz kondensacji w przepływie w minikanałach. Wyniki obliczeń porównano z badaniami eksperymentalnymi z literatury, uzyskując dobrą zgodność.
-
Flow structure, heat transfer and scaling analysis in the case of thermo-magnetic convection in a differentially heated cylindrical enclosure
PublikacjaThe experimental, numerical and scaling analysis in the case of thermo-magnetic convection in a thermosyphon-like enclosure filled with a paramagnetic fluid is presented. Visualization of temperature field together with the numerical simulation gave an information about the flow structure, which indicated “finger-like” structures of hot and cold streams advecting each other. Their number depended on the Rayleigh number and also...
-
Infrared techniques for natural convection investigations in channels between two vertical, parallel, isothermal and symmetrically heated plates
PublikacjaThe effect of the gap width between two symmetrically heated vertical, parallel, isothermal plates on intensity of natural convective heat transfer in a gas (Pr = 0.71) was experimentally studied using the balance and gradient methods. In the former method heat fluxes were determined based on measurements of the voltage and electric current supplying the heaters placed inside the walls. In the latter, heat fluxes were calculated...
-
Numerical simulation of natural convection of Glycol-Al2O3 nanofluids from a horizontal cylinder
PublikacjaThis paper deals with natural convection around a circular cylinder with constant heat flux in a cavity using computational fluid dynamics. As fluids ethylene glycol and a mixture of ethylene glycol with Al2O3 nanoparticles (mass concentrations of nanoparticles: 0.1% and 1%) are chosen. Rayleigh number ranges from 3104 to 3105. The nanofluids are modeled with single-phase approach. For the investigated range of nanoparticle concentration, the...
-
Pool boiling heat transfer of water-Al2O3 and water-Cu nanofluids on horizontal stainless steel smooth and rough tubes
PublikacjaPrzedstawiono wyniki badań eksperymentalnych przejmowania ciepła przy wrzeniu nanocieczy woda-Al2O3 i woda-Cu na poziomych rurkach ze stali nierdzewnej. Ustalono, że niezależnie od badanej koncentracji nanocząstek (0.01%, 0.1% oraz 1%) współczynnik przejmowania ciepła dla nanocieczy był wyższy niż dla wody i rósł ze wzrostem koncentracji. Ponadto współczynnik przejmowania ciepła dla nanocieczy wzrastał ze wzrostem ciśnienia.
-
JOURNAL OF ENHANCED HEAT TRANSFER
Czasopisma -
Experimental verification of the theoretical modelof heat transfer between a liquid layer formed by a two-phase impinging jet and a solid surface
PublikacjaW pracy przedstawiono eksperymentalną weryfikacje modelu teoretycznego wymiany ciepła pomiędzy warstwą wody a stałą powierzchnią. Warstwa cieczy powstała z uderzającej o powierzchnię dwufazowej strugi uderzającej
-
Particle rotation effects in Cosserat-Maxwell boundary layer flow with non-Fourier heat transfer using a new novel approach
Publikacja -
The effect of pressure on heat transfer during pool boiling of water-Al2O3 and water-Cu nanofluids on stainless steel smooth tube
PublikacjaPrzedstawiono wyniki badań eksperymentalnych wrzenia nanocieczy woda-Al2O3 i woda-Cu o koncentracjach nanocząstek 0.01%, 0.1% oraz 1% przy ciśnieniu absolutnym 10 kPa, 100 kPa oraz 200k Pa.
-
The effect of pressure on heat transfer during pool boiling of water-Al2O3 and water-Cu nanofluids on stainless steel smooth tubes
PublikacjaPrzedstawiono wyniki badań eksperymentalnych wrzenia nanocieczy woda-Al2O3 i woda-Cu o koncentracjach nanocząstek 0.01%, 0.1% oraz 1% przy ciśnieniu absolutnym 10 kPa, 100 kPa oraz 200k Pa.
-
Ewa Klugmann-Radziemska prof. dr hab.
OsobyEwa Klugmann-Radziemska ukończyła studia wyższe na kierunku fizyka na Uniwersytecie Gdańskim, a od roku 1996 związana jest z Politechniką Gdańską, kiedy to rozpoczęła studia doktoranckie. Obecnie jest profesorem na Wydziale Chemicznym Politechniki Gdańskiej, od roku 2006 kierownikiem Katedry Aparatury i Maszynoznawstwa Chemicznego. W latach 2008–2016 pełniła funkcję Prodziekana ds. współpracy i rozwoju, w latach 2016-2019 była...
-
Simulation of hybridized nanofluids flowing and heat transfer enhancement via 3-D vertical heated plate using finite element technique
PublikacjaThe present study probed the creation of heat energy and concentrating into Newtonian liquids across vertical 3D-heated plates. The role of the Soret and Dufour theories in concentrating and energy formulas is discussed. The role of hybrid nanoparticles is introduced to illustrate particle efciency in terms of solute and thermal energy. It is removed a viscous dissipation process and a changing magnetic feld. The proposed approach...
-
Pool Boiling of Water–Al2O3 and Water–Cu Nanofluids Outside Porous Coated Tubes
PublikacjaThis paper deals with pool boiling ofwater–Al2O3 and water–Cu nanofluids on porous coated, horizontal tubes. Commercially available stainless-steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate a test heater. Aluminum porous coatings 0.15 mm thick with porosity of about 40% were produced by plasma spraying. A smooth tube served as a reference tube. The experiments were conducted under different...
-
Analytical solution of non-stationary heat conduction problem for two sliding layers with time-dependent friction conditions
PublikacjaIn this article we conduct an overview of various types of thermal contact conditions at the sliding interface. We formulate a problem of non-stationary heat conduction in two sliding layers with generalized thermal contact conditions allowing for dependence of the heat-generation coefficient and contact heat transfer coefficient on time. We then derive an analytical solution of the problem by constructing a special coordinate...
-
Polymerization-Driven Immobilization of dc-APGD Synthesized Gold Nanoparticles into a Quaternary Ammonium-Based Hydrogel Resulting in a Polymeric Nanocomposite with Heat-Transfer Applications
Publikacja -
CO2 capture through direct-contact condensation in a spray ejector condenser and T- junction separator
PublikacjaThe design principle underlying the steam condensation and CO2 purification in a gas power plant with a focus on reducing CO2 emissions encompasses the deployment of a spray ejector condenser (SEC) and separator. This innovative system facilitates direct-contact condensation of steam with non-condensable gas (CO2) by inter acting with a spray of subcooled water, seamlessly integrated with a T-junction separator mechanism aimed...
-
JOURNAL OF HEAT TRANSFER-TRANSACTIONS OF THE ASME
Czasopisma -
Experimental Investigations of Forced Convection of Nanofluids in Smooth, Horizontal, Round Tubes: A Review
PublikacjaA comprehensive review of published works dealing with experimental studies of forced convection heat transfer of nanofluids is presented. The survey is limited to straight, smooth, and round tubes. Moreover, only mono nanofluids exhibiting Newtonian behaviour are considered. Works on experimental research of forced convection in tubes are presented in a chronological order in the first part of the article. In this part, attention...
-
Effect of Flow Normalization in Micro-Pin-Finned Heat Sink: Numerical Study
PublikacjaThe micro-pin-fin heat sink (MPFHS) is widely employed for the heat transfer enhancement of microchannel heat sinks. In the current paper, the effect of flow normalization on the thermohydraulic performance of micro-pin-finned heat sinks is studied numerically. Two geometries of MPFHSs, the conventional design micro-pin-fin heat sink (CD-MPFHS) with a uniform-width micro pin fin and the proposed design micro-pin-fin heat sink (PD-MPFHS)...
-
Application of nanofluids in selected thermal technologies
PublikacjaSome peculiarities regarding convective heat transfer of nanofluids are presented. Particularly, results of the fundamental research concerning pool boiling and single phase convection of nanofluids as well as data obtained for selected heat exchangers operated with nanofluids are discussed.
-
Archives of civil engineering. Intelligent graphic modeler integrating FE analisys of transient heat transfer with early computer-aided design of energy-efficient buildings
PublikacjaW pracy zaprezentowano nowatorski Modeler Rozmyty, w którym zaimplementowano unikalną koncepcję rozpoznawania. Modeler Rozmyty dokonuje ekstrakcji danych geometrycznych poprzez rozpoznanie i identyfikację niedokładnych i niejednorodnych rysunków, złożonych z prostych obiektów graficznych.
-
Wyznaczanie współczynnika przejmowania ciepła podczas wrzenia w przepływie dwutlenku węgla (Prediction of flow boling heat transfer coefficient for carbon dioxide in minichannels)
PublikacjaW pracy przedstawiono wyniki obliczeń uzyskane za pomocą własnego modelu półemirycznego dla wybranych danych eksperymentalnych dla wrzenia w przepływie dwutlenku węgla. Metoda obliczeniowa została zweryfikowana z danymi eksperymentalnymi Docoulombiera i innych (2011) oraz Mastrullo i innych (2009). Badania eksperymentalne dotyczą pełnego zakresu zmienności stopnia suchości oraz zakresu prędkości masowej G=200-1200 kg/m2s. rozwijany...
-
Method of reconstructing two-dimensional velocity fields on the basis of temperature field values measured with a thermal imaging camera
PublikacjaThis paper describes a novel numerical reconstruction procedure (NRP) of the velocity field during natural convective heat transfer from a two-sided, isothermal, heated vertical plate based only on the known temperature field obtained, e.g. with a thermal imaging camera. It has been demonstrated that with a knowledge of temperature distributions, the NRP enables the reconstruction of velocity fields by solving the Navier-Stokes...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
A novel concept of enhanced direct-contact condensation of vapour- inert gas mixture in a spray ejector condenser
PublikacjaAn analytical model of direct steam condensation (DCC) in the novel idea of spray ejector condenser (SEC) in the presence of inert gas has been developed. It is based on continuity, momentum and energy equations for the steam-carbon dioxide mixture and direct contact condensation mechanisms due to heat transfer and concentration. Crucial in the process of DCC is atomisation of the motive fluid in the ejector. The effect of atomised...
-
Bartosz Dawidowicz dr inż.
OsobyAbsolwent Wydziału Budowy Maszyn Politechniki Gdańskiej Mgr inż. - Wydział Budowy Maszyn Politechniki Gdańskiej: specjalizacja: Maszyny i Urządzenia Przemysłu Spożywczego (2000)Dr - Wydział Budowy Maszyn Politechniki Gdańskiej, dyscyplina: budowa i eksploatacja maszyn, specjalność: wymiana ciepła (2008) Zainteresowania naukowe dotyczą m.in. technik wodorowych – ogniwa paliwowe, wykorzystanie wodoru na cele energetyczne, odnawialnych...
-
Analysis of transient heat transfer operation in tube wall.Selected papers from the International Conference on Turbines of Large Output devoted to 100th Anniversary of Prof. Robert Szewalski Birthday.
PublikacjaW pracy przedstawiono zachowanie się wymiennika ciepła stosowanego w układzie regeneracji turbin parowych w niestacjonarnych warunkach pracy.
-
Experimental investigation of forced convection of water-Al2O3 nanofluids inside horizontal tubes,
PublikacjaIn this paper, forced convection of water–Al2O3 nanofluids inside horizontal copper tube is studied experimentally. Experiments were conducted for three, i.e. 0.1%, 1% and 5% nanoparticle mass concentrations under transition and turbulent flow regimes. Average heat transfer coefficients and pressure drop values were determined and compared to distilled water. Enhancement of heat transfer for lower nanoparticle concentration and...
-
Numerical Modelling of Forced Convection of Nanofluids in Smooth, Round Tubes: A Review
PublikacjaA comprehensive review of published works dealing with numerical modelling of forced convection heat transfer and hydrodynamics of nanofluids is presented. Due to the extensive literature, the review is limited to straight, smooth, circular tubes, as this is the basic geometry in shell-and-tube exchangers. Works on numerical modelling of forced convection in tubes are presented chronologically in the first part of the article....
-
Effect of surface roughness on thermal-hydraulic characteristics of plate heat exchanger
PublikacjaIn the paper the experimental analysis of passive heat transfer intensification in the case of modeled plate heat exchanger is conducted. The plate heat exchanger is chosen for the analysis because this kind of heat exchangers could be prospectively applied in the ORC systems, however other areas or application are equally possible. The experimental setup was assembled at the Department of Energy and Industrial Apparatus of Gdansk...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublikacjaFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena, however their description with a single correlation has yet to be suggested. In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the bubble generation is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such...
-
Rheology of Variable Viscosity‐Based Mixed Convective Inclined Magnetized Cross Nanofluid with Varying Thermal Conductivity
PublikacjaCross nanofluid possesses an extraordinary quality among the various fluidic models to explore the key characteristics of flowing fluid during very low and very high shear rates and its viscosity models depend upon shear rate. The current study establishes the numerical treatment regarding variable viscosity‐based mixed convective inclined magnetized Cross nanofluid with var‐ ying thermal conductivities over the moving permeable...
-
Experimental investigation of forced convection of water/EGAl2O3 nanofluids inside horizontal tube
PublikacjaIn this paper, forced convection of water/EG-Al2O3 nanofluids inside horizontal stainless steel tube is studied experimentally. As base fluid served water/EG mixture of two ratios (60:50 and 50:50). Nanoparticle mass concentrations was 0.1% or and 1%. Transition and turbulent flow regimes were tested. Average heat transfer coefficient and pressure drop values were determined for nanofluids and compared to base fluids. Deterioration...
-
Flow boiling of R1233zd(E) in a 3 mm vertical tube at moderate and high reduced pressures
PublikacjaThe results of flow boiling of R1233zd(E) in a 3 mm vertical stainless steel tube are presented at moderate and high saturation temperatures. Integral flow characteristics in the form of pressure drop and heat transfer coefficient are discussed for saturation temperatures ranging from 115 to 145 °C (corresponding reduced pressures from 0.2 to 0.7), mass velocity of 800 kg/m2s and heat flux of 20 kW/m2. All of the obtained heat...
-
Performance of the domestic micro ORC equipped with the shell-and-tube condenser with minichannels
PublikacjaIn this paper, the original compact shell-and-tube heat exchanger with circular minichannels of in-house design and manufacturing is presented as the condenser for the domestic micro heat and power plant investigations as well as other future technical applications. The heat exchanger is equipped with turbulizing baffles inside the shell. The shell itself is made of a tubular sleeve having an inner diameter of 0.067 m and the length...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublikacjaFlow boiling and flow condensation are often regarded as two opposite or symetrical phenomena. Their description however with a single correlation has yet to be suggested.In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the buble generetion is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such case...
-
Jerzy Kowalski dr hab. inż.
Osoby -
Pollutants Transport Phenomena
Kursy OnlineIntroduction to heat and mass transfer phenomena in the environment.
-
Natural convection in symmetrically heated vertical channels
PublikacjaThe study describes natural convection through a vertical channel, open on four sides and bound by two isothermal walls. Both balancing and infrared experimental investigations were performed in air (Pr = 0.71) to estimate the impact of channel width s and wall-to-ambient temperature difference (tw - t∞) on natural convective heat transfer, the formation of air flow patterns and the rate of flow pattern formation. The study was...
-
Three-dimensional numerical investigation of hybrid nanofluids in chain microchannel under electrohydrodynamic actuator
PublikacjaEnergy efficiency enhancement methods have received considerable attentionwithin the industry and scientific community, owing to the rising concern ofglobal energy sustainability. The present article attempts to scrutinize the effectsof electrohydrodynamics and nanofluids on the rate of heat transfer and fluidflow in the 3-D chain microchannels. Improved heat exchangers (e.g., chainmicrochannel) would have a key role in increasing...
-
Pollutants transfer phenomena
Kursy OnlineSubject considering fundamentals of the heat and mass transfer in the environment.
-
PRESSURE DROP OF HFE7000 AND HFE7100 IN FLOW CONDENSATION IN MINICHANNELS WITH ACCOUNT OF NON-ADIABATIC EFFECTS
PublikacjaFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena involving the change of phase. There is a temptation to describe both these phenomena with one only correlation. From amongst the structures present in flow boiling and flow condensation at least the annular flow structure seems to be mostly appropriate to the common modeling. However, the shear stress acting between vapor phase and liquid...