Filtry
wszystkich: 103
Wyniki wyszukiwania dla: BLADE DESIGN
-
Limitations of the Chladni patterns method for determination of circular saw blade critical rotational speeds
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych pił tarczowych z zastosowaniem figur Chladniego do wyznaczania obrotowych prędkości krytycznych pił tarczowych. Otrzymane wyniki wykazały, że w przypadku pił tarczowych o bardziej skomplikowanej budowie z długimi szczelinami, figury Chaldniego opisują postaci drgań, definiują częstotliwości rezonansowe. Jednakże, nie są one przydatne do wyznaczania obrotowych prędkości krytycznych...
-
Parameters of entry and going out of saw blade teeth during cutting with circular saw
PublikacjaW pracy przedstawiono analizę parametrów wejścia i wyjścia ostrzy przy przecinaniu piłami tarczowymi. Określone zostały parametry kątów natarcia i grubości warstwy skrawanej na wejściu i wyjściu ostrzy z materiału w zależności od kinematyki układu.
-
Research into flows in turbine blade seals. Part III: Numerical calculations versus experiment
PublikacjaPrzedstawiono wyniki badań doświadczalnych przepływów w uszczelnieniu nadbandażowym stopnia turbinowego, przeprowadzonych na powietrznej turbinie modelowej. Rezultaty te porównano z wynikami badań numerycznych z zastosowaniem programu Fluent.
-
On design and analysis of flow characteristics of the last stage of gas-steam turbine
PublikacjaResearch regarding blade design and analysis of flow have been conducted for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics (CFD) and computational flow mechanics (CFM). Currently a combination of mentioned methods is used for design of turbine blades. These methods enabled us to improve flow efficiency...
-
Flow visualization and heat transfer investigations on the flat plate with streamwise pressure gradient
PublikacjaPaper presents experimental investigations results for film cooling on a flat plate. The main objective of the design is the streamwise pressure distribution on the flat plate as in the blade cascade. The transient and steady-state technique with liquid crystals for the surface temperature distribution with film cooling has been used in experiments in a low speed wind tunnel.
-
Application scanning laser measurements and wavlet transform for dmagae detection in composite wind turbine blade
PublikacjaW pracy przedstawiono wyniki pomiarów postaci drgań własnych kompozytowej łopaty turbiny wiatrowej. Przedstawiono wyniki detekcji uszkodzeń oparte o analize falkową zmierzonych form drgań.
-
Experimental research of circular saw blade tooth axial run-out influence on cutting effects
PublikacjaW pracy przedstawiono metodę pomiaru i wyniki badań doświadczalnych wpływu bicia osiowego ostrzy piły tarczowej na efekty przecinania
-
The Optimal Spindle Speed Map for Reduction of Chatter Vibration During Milling of Bow Thruster Blade
PublikacjaW artykule przedstwiono przykład wykorzystania procedury tworzenia mapy optymalnych prędkosci obrotowych w celu ograniczenia drgań samowzbudnych podczas frezowania płata śruby okrętowego steru strumieniowego.
-
Washboarding during cutting on frame sawing machines II. Experimental study of the saw blade behaviour
PublikacjaPraca jest swego rodzaju suplementem do referatu przedstawianego na 15th Inernational Wood Machining Seminar w Los Angeles, CA, USA. Opisano uzyskane wyniki badań doświadczalnych prowadzonych w oparciu o plan badań Hartley`a.Czynnikami badanymi były: naprężenia napinające brzeszczotu piły, częstotliwość skoków ramy piłowej oraz wysokość cięcia przedmiotu obrabianego. Czynnikami wynikowymi były: wysokość sfalowania powierzchni oraz...
-
Geometrical conditions of saw blade`s entering into and going out of material during wood cutting
PublikacjaW pracy przedstawiono analizę geometrycznych warunków wejścia i wyjścia ostrza piły z materiału obrabianego przy przecinaniu drewna. Przedstawiono czasowy i przestrzenny rozkład geometrycznych parametrów wejścia i wyjścia ostrza i ich wpływ na trwałość ostrzy i dokładność przecinania.
-
Report on investigation of turbine blade from main engine turbocharger 420.34 from M/V "Nordstraum"
PublikacjaWykonano badania pęknięcia na łopatce turbiny turbodoładowania silnika głównego. Ustalono, ze przyczyną pęknięcia była korozja międzykrystaliczna.
-
Linux scheduler improvement for time demanding network applications, running on Communication Platform Systems
PublikacjaCommunication Platform Systems as ex. ATCA standard blades located in standardized chassis provides high level communication services between system peripherals. Each ATCA blade brings dedicated functionality to the system but can as well exist as separated host responsible for servicing set of task. According to platform philosophy these parts of system can be quite independent against another solutions provided by competitors....
-
The Unsteady Low-Frequency Forces Acting on the Rotor Blade in the First Stage on an Axial Compressor of SO-3 Jet Engine
Publikacja -
ANALYSIS OF THE PROJECT OF INNOVATIVE FLOATING TURBINE
PublikacjaThe design of a floating, innovative device for river water aeration and conversion of mechanical energy to electrical energy required the analysis of a number of geometrical and dynamic features. Such an analysis may be carried out on the basis of existing methods of numerical fluid mechanics. Models of pressures, forces and torques characteristic for the conversion of watercourse energy were developed for two basic concepts of...
-
Uncertainty quantification of modal parameter estimates obtained from subspace identification: An experimental validation on a laboratory test of a large-scale wind turbine blade
PublikacjaThe uncertainty afflicting modal parameter estimates stems from e.g., the finite data length, unknown, or partly measured inputs and the choice of the identification algorithm. Quantification of the related errors with the statistical Delta method is a recent tool, useful in many modern modal analysis applications e.g., damage diagnosis, reliability analysis, model calibration. In this paper, the Delta method-based uncertainty...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublikacjaThe paper presents the results of a design analysis of a microturbine for a cogeneration micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3 kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attentionwas paid...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublikacjaThe paper presents the results of a design analysis of a micro-turbine for a co-generation micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attention was...
-
Economical wood sawing with circular saw blades of a new design (Ekonomicno piljenje drva kruznom pilom novog dezajna)
PublikacjaMaterial-saving and energy-saving belong to the basic requirements imposed on contemporary manufacturing processes. The realization of these processes gives measurable profi ts, not only economical butalso ecological. In the case of wood sawing with circular saw blades, material- and energy-savings are dependent on total overall set of teeth (theoretical kerf) and teeth position accuracy in relation to the workpiece. Hence, it...
-
Application of neural networks for identification of forcedness having effect on magnitude of turbine rotor vibration using pressure distribution in blade tip clearance.
PublikacjaW pracy sprawdzono, czy zastosowanie sieci neuronowych umożliwia identyfikację wymuszeń powstających w wyniku funkcjonowania maszyny jak i zależnych od jej stanu mechanicznego przy zastosowaniu rozkładu ciśnienia w uszczelnieniu nadbandażowym. Przeprowadzono pomiary rozkładu ciśnienia dla różnych warunków pracy, uwzględniając zmianę mimośrodu oraz zmianę skośnego ustawienia osi wirnika względem osi korpusu. Dokonano analiz przy...
-
Application in circular sawing machines of the experimental results of investigations of the chip removing system operation
PublikacjaThe experimental results of the chip removing system operation are presented. The main aim of them was to optimize suction system of the panel saw Fx3 and its follower Fx550. The attention was focused on the upper casing, which was the part of removing system. Within the framework of the work a systematic experimental study of pressure distribution in the casing during operation of the selected rotational speed of saw blade with...