Filtry
wszystkich: 619
Wyniki wyszukiwania dla: MORPHOLOGY
-
Influence of synthesis conditions on zinc oxide nanorode layer morphology
PublikacjaIn recent years one dimensional (1D) nanostructures (nanotubes, nanowires, nanoribbons and nanorods) have been widely studied. Among studied nano-materials, the greatest interest can be seen for zinc oxide (ZnO). However, there is still a need for simple, inexpensive and reproducible fabrication method. In the literature different fabrication methods can be found, most of them requires expensive equipment and involve complex...
-
Left Ventricular Mass: Correlation with Fatness, Hemodynamics and Renal Morphology
Publikacja -
Does morphology of carotid plaque depend on patient's oxidative stress?
Publikacja -
The progress in characterization of polyurethanes morphology with different microscopic methods----WYJAŚNIĆ-----
PublikacjaW pracy opisano wyniki badań dotyczące analizy morfologii poliuretyanów określanej różnymi metodami. Omówiono mikroskopię optyczną, elektronową, mikroskopię termiczną, mikroskopię fluoroscencyjną, mikro-Ramana i mikroskopię sił atomowych.
-
QRS Morphology-Based EDR Signal—Factors Determining its Properties
PublikacjaRespiration-induced signals contain a clinically significant information. It could be obtained utilizing both direct and indirect methods. ECG-Derived Respiration (EDR) method is the latter one. However, in this case, two approaches could be distinguished. First one is based on determining changes in the morphology of QRS complexes while the second one is based on the Respiratory Sinus Arrhythmia (RSA) mechanism. The former approach...
-
Silica xerogel–hydrogen peroxide composites: Their morphology, stability, and antimicrobial activity
Publikacja -
Fatigue fracture morphology of AISI H13 steel obtained by additive manufacturing
PublikacjaThe paper focuses on researching the effect of fatigue loading on metallic structure, lifetime, and fracture surface topographies in AISI H13 steel specimens obtained by selective laser melting (SLM). The topography of the fracture surfaces was measured over their entire area, according to the entire total area method, with an optical three-dimensional surface measurement system. The fatigue results of the SLM 3D printed steel...
-
Renal morphology assessed by ultrasound in relation to central haemodynamics and body fat
Publikacja -
Hybrid carbon-TiO2 spheres: Investigation of structure, morphology and spectroscopic studies
Publikacja -
Silica xerogel-hydrogen peroxide composite: their morphology, stability, and antimicrobial activity
PublikacjaOpracowano metody otrzymywania stabilnego kompozytu złożonego z kserożelu krzemionkowego i nadtlenku wodoru w szerokim zakresie stężeń H2O2. Przeprowadzono charakterystykę otrzymanego kompozytu. W szczególności określono morfologię kompozytu, stabilność termiczną oraz dokonano oceny właściwości bakteriobójczych preparatu.
-
Deposition, morphology and functional properties of layers based on DLC:Si and DLC:N on polyurethane
Publikacja -
Morphology studies of the cobalt base clad layers produced by laser technology.
PublikacjaPrzedmiotem badań były utwardzające warstwy wykonane na przylgni zaworów wydechowych silnika spalinowego. Materiał podłoża to stal H10S2M. Zastosowano technologię napawania laserowego proszków na bazie kobaltu. Proszki różniły się jedynie zawartością wolframu i zawierały odpowiednio 4,9; 5,3 i 9 wg% tego pierwiastka. Parametry napawania były jednakowe dla wszystkich proszków. Otrzymane warstwy różniły się twardością na powierzchni...
-
Controlling the size and morphology of precipitated calcite particles by the selection of solvent composition
PublikacjaCalcium carbonate particles were obtained in the reaction of calcium hydroxide with carbon dioxide at 65°C. Initial Ca(OH)2 suspensions were prepared in pure water and aqueous solutions of ethylene glycol or glycerol of the concentration range up to 20% (vol.). The course of reaction was monitored by conductivity measurements. Precipitated solids were analyzed by FTIR, XRD, SEM and the particles size distribution was determined...
-
PARAMETERS OF THE ELECTROPHORETIC DEPOSITION PROCESS AND ITS INFLUENCE ON THE MORPHOLOGY OF HYDROXYAPATITE COATINGS. REVIEW
PublikacjaMetallic materials intended for bone implants should exhibit not only appropriate mechanical properties, but also high biocompatibility. The surface treatment modifications, for example acidic treatment, laser treatment, ion implantation and deposition of highly biocompatible coatings, are practiced. One of the most popular methods of surface modification is to deposit hydroxyapatite (HAp) coatings. HAp naturally occurs in human...
-
The determinants of morphology and properties of the nanohydroxyapatite coating deposited on the Ti13Zr13Nb alloy by electrophoretic techniqe
PublikacjaThe titanium and its alloys belong at present to the most preferred and commonly applied biomaterials for load- bearing implants. The surfaces of biomaterials are subjected to modification, including the hydroxyapatite coatings deposited in order to ensure corrosion resistance and better joining between an implant and a bone through the possibility of ingrowth bone into the coating. In this paper, the morphology and properties...
-
Effect of kenaf fibre modification on morphology and mechanical properties of thermoplastic polyurethane materials
PublikacjaThe presented study examined the morphology and mechanical properties of biocomposites obtained from kenaf natural fibre and thermoplastic polyurethane. Kenaf was modified using various methods, namely: acetylation, blocked isocyanate, maleic anhydride and permanganate treatment. Those methods and ways of carrying out of surface modifications were not studied before on kenaf/thermoplastic polyurethane composites. Different fibre...
-
Influence of Hydrogenation on Morphology, Chemical Structure and Photocatalytic Efficiency of Graphitic Carbon Nitride
Publikacja -
Influence of morphology of PVDF capillary membranes on the performance of direct contact membrane distillation
Publikacja -
Synthesis of carbon nanotubes and nanospheres with controlled morphology using different catalyst precursors
Publikacja -
Influence of Thermal Modification and Morphology of TiO2 Nanotubes on Their Electrochemical Properties for Biosensors Applications
Publikacja