Filtry
wszystkich: 616
wybranych: 563
Wyniki wyszukiwania dla: AMPHIPHILIC COPOLYMERS
-
Effect of Coating Material Properties on Tilting-pad Thrust Bearing Performance
PublikacjaPolymer lined tilting-pad bearings demonstrate many advantages over traditional bearing systems. Bearings with a polymer layer in comparison with a babbitted layer show, for example: lower value of friction coefficient (important during start/stops), higher fatigue strength of the coating, better distribution of the load on individual pads due to lower elasticity of the polymers, wider range of operational temperatures or the ability...
-
Chitosan, Collagen and Gelatin in the design of novel materials with antimicrobial acticity
PublikacjaMedical devices containing and releasing antiinfective agents directly on the site of injury are a common group of materials available and widely used in treating difficult to heal wounds. Sustained contact of the active agent to the damaged tissue, needed to inhibit infection and preservation of microbiological purity of the wound, is provided by the immobilization antimicrobial agents on the surface of the matrix material or...
-
Tensile and Fatigue Behavior of Additive Manufactured Polylactide
PublikacjaThis article presents the results of monotonic tensile and fatigue tests conducted on commercial polylactide or polylactic acid (PLA). The results of fatigue tests for this material present in the literature are limited, especially for additive manufactured elements. The specimens were manufactured using the injection molding and the fused filament fabrication (FFF) method. The FFF specimens were divided into five subgroups, depending...
-
A facile structural manipulation strategy to prepare ultra-strong, super-tough, and thermally stable polylactide/nucleating agent composites
PublikacjaPolylactide (PLA) is a biodegradable thermoplastic widely used in diferent felds, but it should be adequately modifed considering high-performance applications. However, the current processes for developing PLA materials achieve high strength at the expense of toughness or ductility of the materials. Therefore, there is need to develop new strategies for generation of PLA materials with high strength, great toughness, good ductility,...
-
Polyurethane based hybrid ciprofloxacin-releasing wound dressings designed for skin engineering purpose
PublikacjaPurpose Even in the 21st century, chronic wounds still pose a major challenge due to potentially inappropriate treatment options, so the latest wound dressings are hybrid systems that enable clinical management, such as a hybrid of hydrogels, antibiotics and polymers. These wound dressings are mainly used for chronic and complex wounds, which can easily be infected by bacteria. Materials and methods Six Composite Porous Matrices...
-
Structural, spectral and magnetic properties of Ni(II), Co(II) and Cd(II) compounds with imidazole derivatives and silanethiolate ligands
PublikacjaA series of new metal heteroleptic complexes have been obtained in simple reactions of 1-(3-aminopropyl)-imidazole (api) and 1,4-bis(imidazol-1-yl)-butane (bbi) ligands with metal silanethiolates or acetylacetonates. The obtained complexes are the coordination polymers [Ni{SSi(tBuO)3}2(μ-api)]n1, [Co{SSi(tBuO)3}2(μ-api)]n2, [Cd{SSi(tBuO)3}2(μ-api)·2CH3OH]n3, [Cd{SSi(tBuO)3}2(μ-bbi)·CHCl3]n4 and the dimer [Co{SSi(tBuO)3}2(μ-bbi)·3CH3OH]25....
-
Electrophoretic deposition and characterization of composite chitosan/Eudragit E 100 or poly(4-vinylpyridine)/mesoporous bioactive glass nanoparticles coatings on pre-treated titanium for implant applications
PublikacjaTitanium implants are surface-modified to achieve bioactivity and often antibacterial properties. Such surface coatings may increase corrosion degradation and be weakly attached to the substrate. In the present research, biodegradable composite coatings, investigated so far as smart environment-sensitive, slowly releasing silver to the implant neighborhood, were produced as a combination of chitosan (CS) with Eudragit E 100 (EE100)...
-
Fabrication of polyurethane and polyurethane based composite fibers by the electrospinning technique for soft tissue engineering of cardiovascular system
PublikacjaElectrospinning is the unique technique, which provides forming of polymeric scaffolds for soft tissue engineering, which include tissue scaffolds for soft tissues of cardiovascular system. Such artificial soft tissues of cardiovascular system may possess mechanical properties comparable to native vascular tissues. Electrospinning technique gives the opportu nity to form fibres with nm- to μm-scale in diameter. The arrangement...
-
The effect of boron concentration on the electrical, morphological and optical properties of boron-doped nanocrystalline diamond sheets: Tuning the diamond-on-graphene vertical junction
PublikacjaIn this paper, the effect of boron doping on the electrical, morphological and structural properties of free-standing nanocrystalline diamond sheets (thickness ~ 1 μm) was investigated. For this purpose, we used diamond films delaminated from a mirror-polished tantalum substrate following a microwave plasma-assisted chemical vapor deposition process, each grown with a different [B]/[C] ratio (up to 20,000 ppm) in the gas phase....
-
Sintering Parameter Investigation for Bimetallic Stainless Steel 316L/Inconel 718 Composite Printed by Dual-Nozzle Fused Deposition Modeling
PublikacjaFused deposition modeling (FDM) nowadays offers promising future applications for fabricating not only thermoplastic-based polymers but also composite PLA/Metal alloy materials, this capability bridges the need for metallic components in complex manufacturing processes. The research is to explore the manufacturability of multi-metal parts by printing green bodies of PLA/multi-metal objects, carrying these objects to the debinding...
-
Advancements in the Additive Manufacturing of Magnesium and Aluminum Alloys through Laser-Based Approach
PublikacjaComplex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives such as reduced part numbers, greater functionality, and lightweight, among others. Polymers, metals, and ceramics are the few materials that can be used in AM technology, but metallic materials (Magnesium and Aluminum) are attracting more attention from the research and industrial point of view. Understanding the role...
-
Plastic Debris in the Stomach of the Invasive Signal Crayfish Pacifastacus leniusculus from a Baltic Coastal River
PublikacjaPollution by plastic debris, widely recognized as a growing global problem [1-3] is caused by the production of synthetic polymers. Over recent years, the production of plastics has increased, while in Europe, fossil-based plastics production has decreased, and recycled plastics production has increased [4]. There are different types of plastics. Some types of plastic ingredients, applied in a wide variety of cosmetics and personal...
-
Pilicides effectively hinder chaperone-usher interactions in all Gram-negative bacteria
PublikacjaThe chaperone-usher pathway of adhesive structures biogenesis is highly conserved in all Gram-negative bacteria. Pili are polymers of thousands protein subunits that possess conserved immunoglobuline-like structure denoted by lack of the seventh G strand. The effect of this structural defect is a hydrophobic acceptor cleft. The folding of protein subunits is strictly dependent on the action of specific periplasmic chaperone protein...