Wyniki wyszukiwania dla: RECONFIGURABLE ANTENNAS
-
Size reduction of ultra-wideband antennas with efficiency and matching constraints
PublikacjaAntenna design is a multifaceted task that involves handling of various performance figures concerning both electrical performance of the structure as well as its geometry. Simultaneous control of several objectives through rigorous optimization is very challenging and virtually impossible through conventional approaches such as parameter sweeping. In this work, we investigate size reduction of ultra‐wideband antenna structures...
-
Multi-objective optimization for assessment of topological modification in UWB antennas
PublikacjaThis paper addresses an issue of systematic and rigorous assessment of effects of topological modifications on the performance of compact UWB antennas. Application of fast surrogate-assisted multi-objective optimization procedures allows us for obtaining, in a practically acceptable timeframe, a set of designs representing the best possible trade-offs between conflicting objectives (here, antenna size minimization and reduction...
-
Two-Stage Variable-Fidelity Modeling of Antennas with Domain Confinement
PublikacjaSurrogate modeling has become the method of choice in solving an increasing number of antenna design tasks, especially those involving expensive full-wave electromagnetic (EM) simulations. Notwithstanding, the curse of dimensionality considerably affects conventional metamodeling methods, and their capability to efficiently handle nonlinear antenna characteristics over broad ranges of the system parameters is limited. Performance-driven...
-
Elliptical slot UWB monopole antenna
PublikacjaThe UWB monopole antenna with elliptical radiating slot end and microstrip feeding line terminated with radial stub have been designed, fabricated and measured. The antenna show return loss less than -12 dB in the whole UWB bandwidth. Linearity of the reflection coefficient phase product have also been achieved. Radiation patterns of the antenna measured at three selected frequency points indicated regular, approximately omni directional...
-
Transmission measurements between two geometrically small Vivaldi antennas performed in non-anechoic propagation conditions
Dane BadawczeThe dataset contains unprocessed measurements of complex transmission (and reflection) characteristics obtained in non-anechoic regime for a geometrically small, broadband spline-parameterized Vivaldi structure. The measurement setup comprises two Vivaldi antennas with the same topology where one is used as a reference structure, and another one as...
-
Expedited Globalized Antenna Optimization by Principal Components and Variable-Fidelity EM Simulations: Application to Microstrip Antenna Design
PublikacjaParameter optimization, also referred to as design closure, is imperative in the development of modern antennas. Theoretical considerations along with rough dimension adjustment through supervised parameter sweeping can only yield initial designs that need to be further tuned to boost the antenna performance. The major challenges include handling of multi-dimensional parameter spaces while accounting for several objectives and...
-
Multi-Beam Antenna for Ka-Band CubeSat Connectivity Using 3-D Printed Lens and Antenna Array
PublikacjaIn this paper, the design of a passive multi-beam lens antenna is proposed for the CubeSat space communication system as an alternative application of a 2-D microstrip antenna array that has originally been designed for a 39 GHz 5 G MU-MIMO system. The half-ellipsoid lens is 3-D printed using stereolithography (SLA) technology. The antenna prototype is capable of selecting the main beam between 16 different directions with a gain...
-
International Journal on Communications Antenna and Propagation (IRECAP)
Czasopisma -
IEE PROCEEDINGS-MICROWAVES ANTENNAS AND PROPAGATION
Czasopisma -
Compact-planar monopole loop antennas for 802.11b/g WLAN systems
PublikacjaZaproponowano planarne anteny monopolowe dla systemów komunikacji bezprzewodowej WLAN pracujących w pasmach 2.45GHz i 5.25GHz. W strukturze radiatorów zasilanych poprzez linię mikropaskową wykorzystano krzywe fraktalne: pętlę Kocha oraz pętlę Minkowskiego. W obu przypadkach uzyskano dwuzakresową pracę anten dzięki wprowadzeniu nowej konfiguracji zminiaturyzowanych transformatorów impedancji w układzie zasilania.
-
Verification of ESPAR Antennas Performance in the Simple and Calibration Free Localization System
PublikacjaThis paper presents the results of simulations and measurements of an indoor localization system that uses Electronically Steerable Parasitic Array Radiator (ESPAR) antennas with switched directional beam. Proposed antennas are dedicated for 2.4GHz ISM low-cost applications where determination of the incoming signal is required. The antennas performance is analyzed and verified with relation to positioning methods based on the...
-
Cost-efficient design optimization of compact patch antennas with improved bandwidth
PublikacjaIn this letter, a surrogate-assisted optimization procedure for fast design of compact patch antennas with enhanced bandwidth is presented. The procedure aims at addressing a fundamental challenge of the design of antenna structures with complex topologies, which is simultaneous adjustment of numerous geometry parameters. The latter is necessary in order to find a truly optimum design and cannot be executed-at the level of high-fidelity...
-
Improved Uniform Sampling in Constrained Domains for Data-Driven Modelling of Antennas
PublikacjaData-driven surrogate modelling of antenna structures is an attractive way of accelerating the design process, in particular, parametric optimization. In practice, construction of surrogates is hindered by curse of dimensionality as well as wide ranges of geometry parameters that need to be covered in order to make the model useful. These difficulties can be alleviated by constrained performance-driven modelling with the surrogate...
-
Fast surrogate-assisted frequency scaling of planar antennas with circular polarisation
PublikacjaIn this work, the problem of computationally efficient frequency scaling (re-design) of circular polarisation antennas is addressed using surrogate-assisted techniques. The task is challenging and requires the identification of the optimum geometry parameters to enable the operation of the re-designed structure at a selected (required) centre frequency. This involves handling several performance figures such as the antenna gain,...
-
Low-Cost EM-Simulation-Driven Multi-Objective Optimization of Antennas
PublikacjaA surrogate-based method for efficient multi-objective antenna optimization is presented. Our technique exploits response surface approximation (RSA) model constructed from sampled low-fidelity antenna model (here, obtained through coarse-discretization EM simulation). The RSA model enables fast determination of the best available trade-offs between conflicting design goals. A low-cost RSA model construction is possible through...
-
Fast simulation-driven design optimization of UWB band-notch antennas
PublikacjaIn this letter, a simple yet reliable and automated methodology for rapid design optimization of ultra-wideband (UWB) band-notch antennas is presented. Our approach is a two-stage procedure with the first stage focused on the design of the antenna itself, and the secondstage aiming at identification of the appropriate dimensions of the resonator with the purpose of allocating the band-notch in the desired frequency range. For the...
-
Performance-Driven Inverse/Forward Modeling of Antennas in Variable-Thickness Domains
PublikacjaDesign of contemporary antenna systems is a challenging endeavor. The difficulties are partially rooted in stringent specifications imposed on both electrical and field characteristics, demands concerning various functionalities, but also constraints imposed upon the physical size of the radiators. Furthermore, conducting the design process at the level of full-wave electromagnetic (EM) simulations, otherwise dictated by reliability,...
-
Rapid Design of 3D Reflectarray Antennas by Inverse Surrogate Modeling and Regularization
PublikacjaReflectarrays (RAs) exhibit important advantages over conventional antenna arrays, especially in terms of realizing pencil-beam patterns without the employment of the feeding networks. Unfortunately, microstrip RA implementations feature narrow bandwidths, and are severely affected by losses. A considerably improved performance can be achieved for RAs involving grounded dielectric layers, which are also easy to manufacture using...
-
Low-Cost Behavioral Modeling of Antennas by Dimensionality Reduction and Domain Confinement
PublikacjaBehavioral modeling has been rising in importance in modern antenna design. It is primarily employed to diminish the computational cost of procedures involving massive full-wave electromagnetic (EM) simulations. Cheaper alternative offer surrogate models, yet, setting up data-driven surrogates is impeded by, among others, the curse of dimensionality. This article introduces a novel approach to reduced-cost surrogate modeling of...
-
Optimal Design of Transmitarray Antennas via Low-Cost Surrogate Modelling
PublikacjaOver the recent years, reflectarrays and transmitarrays have been drawing a considerable attention due to their attractive features, including a possibility of realizing high gain and pencil-like radiation patterns without the employment of complex feeding networks. Among the two, transmitarrays seem to be superior over reflectarrays in terms of achieving high radiation efficiency without the feed blockage. Notwithstanding, the...
-
The use of numerical methods for the analysis of phase phenomena in multi element antennas.
PublikacjaW artykule zostały zaprezentowane wyniki analizy wpływu wzajemnej i własnej impedancji promieniowania na fazę sygnału odbieranego przez antenę wieloelementową. Obliczenia dokonano dla elektrycznego modelu zastępczego Mason`a przetwornika ultradźwiękowego.
-
Simple 60 GHz Switched Beam Antenna for 5G Millimeter-Wave Applications
PublikacjaA new 60 GHz band single-input switched beam antenna is proposed for the fifth-generation (5G) millimeter-wave network applications. The presented design is capable of electronically switching the main beam in two different directions via a proposed microstrip-line-to-slotline single-pole dual-throw (SPDT) switch based on commercially available p-i-n diodes. The antenna is fabricated in a low-cost printed circuit board process...
-
UWB planar antenna dipole in the sandwich configuration
PublikacjaW pracy przedstawiono wyniki badań nad planarną anteną dipolową o ramionach kołowych, przeznaczoną dla systemu UWB. Ramiona dipola umieszczono pomiędzy dwoma warstwami dielektryka (konfiguracja kanapki) uzyskując redukcję wymiarów anteny. Stwierdzono, że impedancja wejściowa jest mniejsza, niż w przypadku pojedynczego podłoża, co umożliwia łatwiejsze dopasowanie anteny do toru zasilającego. Współczynnik odbicia w całym paśmie...
-
Ridged horn antenna for ground penetrating radar
PublikacjaOmówiono modyfikację tuby grzbietowej polegającą na jej wypełnieniu dielektrykiem, w celu wykorzystania do układu pozwalającego na poszukiwanie obiektów znajdujących się pod ziemią. Omówiono badania, które doprowadziły do opracowania konstrukcji anteny z wypełnieniem dielektrycznym. Przedstawiono wyniki testu takiej anteny w układzie do detekcji obiektu metalowego umieszczonego pod ziemią.
-
Design-Oriented Constrained Modeling of Antenna Structures
PublikacjaFast surrogate models are crucially important to reduce the cost of design process of antenna structures. Due to curse of dimensionality, standard (data-driven) modeling methods exhibit serious limitations concerning the number of independent geometry parameters that can be handled but also (and even more importantly) their parameter ranges. In this work, a design-oriented modeling framework is proposed in which the surrogate is...
-
Simulation-Driven Design of Microstrip Antenna Subarrays
PublikacjaA methodology for computationally efficient simulation-driven design of microstrip antenna subarrays is presented. Our approach takes into account the effect of the feed (e.g., a corporate network) on the subarray side lobe level and allows adjusting both radiation and reflection responses of the structure under design within a single automated process. This process is realized as surrogate-based optimization that produces designs...
-
Sierpinski Monopole Antenna - Uniplanar Feeding Technique.
PublikacjaPrzedstawiono różne techniki zasilania monopolowych anten fraktalnych typu Sierpinskiego. Zaproponowano nowe sposoby zasilania: poprzez linię współosiową ze zmodyfikowaną rozszerzoną płaszczyzną masy oraz poprzez linię współosiową i falowód koplanarny. W obu przypadkach możliwa była znaczna miniaturyzacja struktury. Wykonane i przebadane prototypy anten potwierdziły przydatność przedstawionych rozwiązań.
-
Low-fidelity model considerations for simulation-based optimisation of miniaturised wideband antennas
PublikacjaHere, variable-fidelity electromagnetic (EM)-based design optimisation of miniaturised antennas is discussed. The authors focus on an appropriate selection of discretisation density of the low-fidelity EM model, which results in good performance of the optimisation algorithm in terms of its computational complexity and reliability. Trust-region gradient search with low-fidelity model corrected by means of non-linear frequency scaling...
-
Comprehensive dimension scaling of multi-band antennas for operating frequencies and substrate parameters
PublikacjaIn this paper, low-cost and comprehensive redesign of multi-band antennas with respect to the operating frequencies and material parameters of the substrate is presented. Our approach exploits an inverse surrogate model identified based on a set of reference designs optimized at the level of coarse-discretization EM simulations of the antenna at hand. An iterative correction procedure is also implemented to account for the initial...
-
Expedited simulation-driven design optimization of UWB antennas by means of response features
PublikacjaIn this work, a method for fast design optimization of broadband antennas is considered. The approach is based on a feature-based optimization (FBO) concept where reflection characteristics of the structure at hand are formulated in terms of suitably defined feature points. Redefinition of the design problem allows for reducing the design optimization cost, because the dependence of feature point coordinates on antenna dimensions...
-
A novel calibration method for RSS-based DoA estimation using ESPAR antennas
PublikacjaIn this paper, we introduce a new calibration method that can successfully be used in direction of arrival (DoA) estimation using electronically steerable parasitic array radiator (ESPAR) antennas and employing power-pattern cross-correlation (PPCC) algorithm, which relies on received signal strength (RSS) values recorded at the antenna output port. Instead of the commonly used two-step approach, during which ESPAR antenna calibration...
-
Rapid redesign of multiband antennas with respect to operating conditions and material parameters of substrate
PublikacjaThis work addresses geometry parameter scaling of multi-band antennas for Internet of Things applications. The presented approach is comprehensive and permits re-design of the structure with respect to both the operating frequencies and material parameters of the dielectric substrate. A two-step procedure is developed with the initial design obtained from an inverse surrogate model constructed using a set of appropriately prepared...
-
RSS-Based DoA Estimation for ESPAR Antennas Using Support Vector Machine
PublikacjaIn this letter, it is shown how direction-of-arrival (DoA) estimation for electronically steerable parasitic array radiator (ESPAR) antennas, which are designed to be integrated within wireless sensor network nodes, can be improved by applying support vector classification approach to received signal strength (RSS) values recorded at an antenna's output port. The proposed method relies on ESPAR antenna's radiation patterns measured...
-
RSS-based DoA Estimation Using ESPAR Antennas and Interpolated Radiation Patterns
PublikacjaIn this letter, it is shown how an algorithm, which employs received signal strength (RSS) values in order to estimate direction-of-arrival (DoA) of impinging signals in wireless sensor network (WSN) nodes equipped with electronically steerable parasitic array radiator (ESPAR) antennas, can easily be improved by applying an interpolation algorithm to radiation patterns recorded in the calibration phase of the DoA estimation process....
-
Accelerated multi-objective design optimization of antennas by surrogate modeling and domain segmentation
PublikacjaMulti-objective optimization yields indispensable information about the best possible design trade-offs of an antenna structure, yet it is challenging if full-wave electromagnetic (EM) analysis is utilized for performance evaluation. The latter is a necessity for majority of contemporary antennas as it is the only way of achieving acceptable modeling accuracy. In this paper, a procedure for accelerated multi-objective design of...
-
Rapid dimension scaling of triple-band antennas by means of inverse surrogate modeling
PublikacjaGeometry scaling of antennas, i.e., finding optimum dimensions of the structure for given operating conditions and material parameters is an important yet challenging problem. In this paper, we discuss fast dimension scaling of triple-band antennas with respect to operating frequencies. We adopt the inverse surrogate modeling approach where the surrogate model is a function of the three operating frequencies of the antenna and...
-
Computationally Efficient Surrogate-Assisted Design of Pyramidal-Shaped 3D Reflectarray Antennas
PublikacjaReflectarrays (RAs) have been attracting considerable interest in the recent years due to their appealing features, in particular, a possibility of realizing pencil-beam radiation patterns, as in the phased arrays, but without the necessity of incorporating the feeding networks. These characteristics make them attractive solutions, among others, for satellite communications or mobile radar antennas. Notwithstanding, available microstrip...
-
Multi-Criterial Design of Antennas with Tolerance Analysis Using Response-Feature Predictors
PublikacjaImperfect manufacturing is one of the factors affecting the performance of antenna systems. It is particularly important when design specifications are strict and leave a minimum leeway for a degradation caused by geometry or material parameter deviations from their nominal values. At the same time, conventional antenna design procedures routinely neglect to take the fabrication tolerances into account, which is mainly a result...
-
On Unsupervised Artificial-Intelligence-Assisted Design of Antennas for High-Performance Planar Devices
PublikacjaDesign of modern antenna structures is a challenging endeavor. It is laborious, and heavily reliant on engineering insight and experience, especially at the initial stages oriented towards the devel-opment of a suitable antenna architecture. Due to its interactive nature and hands-on procedures (mainly parametric studies) for validating suitability of particular geometric setups, typical antenna development requires many weeks...
-
Kinematyka jako odpowiedź na współczesną potrzebę tworzenia przestrzeni = KINEMATICS AS AN ANSWER TO THE CURRENT NEED TO CREATE A RE-CONFIGURABLE SPACE
PublikacjaPrzestrzeń re-konfigurowalna pojawiły się w sztuce i architekturze już w pierwszej połowie XX wieku jako forma odpowiedzi na na pytania, które stawia przed nią świat. Nasze życie i potrzeby zmieniają się niesamowicie dynamicznie. Postfordowski model społeczeństwa sprzyja generowaniu zjawisk, których jeszcze rok temu nie brano pod uwagę. Stąd architektura próbuje stanowić odpowiedź na problemy jeszcze niezaistniałe. Jedną z jej...
-
Broadband Microstrip Patch Antenna with Reduced Transversal Size
PublikacjaW pracy przedstawiono propozycję anteny szerokopasmowej o ograniczonych wymiarach poprzecznych. Szerokopasmowość uzyskano poprzez stosowanie grubego podłoża i sprzężenia elektromagnetycznego poprzez dwie szczeliny sprzęgające. Wymiar poprzeczny łaty zredukowano poprzez zastosowanie szczeliny typu H. Antena została zaprojektowana i wykonana, zaś zmierzone pasmo wyniosło 29% dla WFS <1.5. Stwierdzono jednak, że charakterystyki...
-
Inexpensive Helical Antenna for Global Navigation Satellite Systems
PublikacjaZaprezentowane zostały wyniki badań teoretycznych oraz eksperymentalnych niskobudżetowej anteny na pasmo L. Wyjściowa geometria struktury została obliczona na podstawie ogólnych wzorów. Efekt przesunięcia częstotliwości wywołany przez użycie rdzenia PU został również uwzględniony. Równolegle przeprowadzono badania wrażliwości parametrów anteny na proces produkcji. Zaprojektowano i wykonano układ dopasowania impedancyjnego. W paśmie...
-
Double-ridged horn antenna with sinusoidal ridge profile
PublikacjaPrzedstawiono wyniki symulacji numerycznej oraz pomiarów parametrów anteny tubowej z podwójnym grzbietem. Badania numeryczne dotyczyły zarówno samego układu zasilania falowodu grzbietowego jak i całej anteny z uwzględnieniem sinusoidalnego profilu impedancji grzbietu. Wyniki obliczeń dopasowania oraz charakterystyk promieniowania, wykonanych przy użyciu symulatora QW-3D, porównano z wynikami pomiarów, stwierdzając dobrą zgodność...
-
Design optimization of novel compact circular polarization antenna
PublikacjaThe paper describes a structure and a design optimization procedure of a miniaturized circular polarization antenna with elliptical ground plane slots and feed line with stepped-impedance stubs. Constrained optimization of all antenna parameters is executed in order to explicitly reduce the antenna size while maintaining required impedance axial ratio bandwidth of 5 GHz to 7 GHz at the same time. The size of the optimized antenna...
-
Compact antenna array comprising fractal-shaped microstripradiators
PublikacjaA design method of antenna array consisting of eight microstrip patches modified with Sierpinski fractal curves has been presented andexperimentally validated in this paper. Method proposed has enabled the achievement of considerable miniaturization of array length (26%),together with multi-band behavior of the antenna, which proves the attractiveness of presented design methodology and its ability to be implemented in more complex...
-
A Geometrically Simple Compact Wideband Circularly Polarized Antenna
PublikacjaA compact broadband wide-slot circular polarization (CP) antenna is proposed. An inverted L-shape parasitic strip at the open end of a microstrip line extension and a slot modification is applied to attain wideband CP. The advantage of this technique is simplicity which makes it readily re-designable for different frequency bands. To demonstrate the concept, three designs working at different frequencies are obtained. The redesign...
-
Design of UWB coplanar antenna with reduced ground plane
PublikacjaW artykule przedstawiono projekt kompaktowej anteny szerokopasmowej złożonej z dwóch kołowych pasków koplanarnych ograniczających szczelinę o podobnym kształcie. Antena zasilona była z 50 Ω linii trójpaskowej. Przeprowadzono badania wpływu zewnętrznego paska na pasmo anteny. Zaprojektowana antena została zbadana eksperymentalnie pokazując bardzo dobre parametry: w paśmie 1.7-15.5GHz uzyskano |S11| < −10dB. Antena charakteryzowała...
-
A structure and design of a novel compact UWB MIMO antenna
PublikacjaIn the paper, a concept and design procedure of a novel compact MIMO slot antenna is presented. In order to achieve a better filling of available space, individual antennas are constrained to a triangular shape and optimized for a reduced size. The MIMO structure is then assembled using the two of previously designed antennas in orthogonal arrangement. Surrogate-assisted numerical optimization involving variable-fidelity electromagnetic...
-
Novel structure and design of compact UWB slot antenna
PublikacjaIn this paper, a novel structure of a compact UWB slot antenna is presented along with a simulation-driven design optimization algorithm for adjusting geometry parameters of the device. Our primary objective is to obtain small footprint of the structure while maintaining its acceptable electrical performance. It is achieved by introducing sufficiently large number of geometry degrees of freedom, including increased number of parameterized...
-
Diagnostics of thermal processes in antenna systems of broadcast stations
PublikacjaDiagnostics is an important element associated with the operation of a radio antenna systems, allowing earlier detection of potential damage. Thermography is one of the diagnostic tools, which allows for non-invasive assessment of technical condition. It brings together both financial savings associated with the removal of the damage and the potential effects caused by it. The article presents an example of using a thermal imaging...