Filters
total: 3364
filtered: 2552
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: STEAM TURBINE CONTROL
-
Neural Modelling of Steam Turbine Control Stage
PublicationThe paper describes possibility of steam turbine control stage neural model creation. It is of great importance because wider application of green energy causes severe conditions for control of energy generation systems operation Results of chosen steam turbine of 200 MW power measurements are applied as an example showing way of neural model creation. They serve as training and testing data of such neural model. Relatively simple...
-
The QDMC Model Predictive Controller for the Nuclear Power Plant Steam Turbine Control
PublicationThere are typically two main control loops with PI con trollers operating at each turbo-generator set. In this paper a model predictive controller QDMC for the steam turbine is proposed - instead of a typical PI controller. The QDMC controller utilize a step-response model for the controlled system. This model parameters are determined, based on the simplified and linear model of turbo-generator set, which parameters are identified...
-
Studies of the Modelling Accuracy of Steam Turbine Control Systems for Diagnostic Tests of Automatic Synchronizers
PublicationOne of the important factors that affect the reliable operation of the power system and the rapid restitution after disaster is a quick and effective combining synchronous electric power facilities to operate in parallel. Hence, diagnostics of automatic synchronizers at every stage of their life, from building a prototype, through the whole life, until removing such devices from the operation, is an extremely important and responsible...
-
Nuclear Power Plant Steam Turbine - Modeling for Model Based Control Purposes
PublicationThe nature of the processes taking place in a nuclear power plant (NPP) steam turbine is the reason why their modeling is very difficult, especially when the model is intended to be used for on-line optimal model based process control over a wide range of operating conditions, caused by changing electrical power demand e.g. when combined heat and power mode of work is utilized. The paper presents three nonlinear models of NPP steam...
-
TERMODYNAMIC CALCULATIONS OF TURBINE STEAM PARAMETERS
PublicationIn this work a heat balance was made for the nominal conditions of a block working with 18K370 turbine. For the parameters obtained, the thermal-flow calculations of the steam turbine were performed, maintaining the actual geometry of its flow system. Based on the nominal values obtained, iterative thermal and flow calculations were made for both the heat cycle of the power plant block and the steam turbine itself, seeking to obtain...
-
Remarks on steam condensation modeling related to steam turbine large output
PublicationIn the paper numerical simulations have been performed to predict the performance of the diferent steam models. All of the considered models of steam condensation have been validated on the base of benchmark experiment employing expansion in nozzle and next on the low pressure part of the steam turbine equipped with the so-called Baumann stage. For numerical analysis three models have been finally used - the ideal steam model without...
-
Proposition of the steam turbine governor structure modification
PublicationThere is considered the steam turbine governor operation during defense and restoration of the power system. It points out weaknesses of currently used governor structures. The new controller is proposed, that takes advantages of those curently used. The new controller allows for more effective control of the turbine in emergency situations, at frequencies much different from the nominal value.
-
Modelling of Nuclear Power Plant Steam Turbine
PublicationThe paper describes the approach to a Nuclear Power Plant steam turbine modelling which would enable on-line optimal process control (model based) and diagnosis over wide range of operating conditions caused by changing power demand. Presented model is static, multivariable and nonlinear. Such model enables analyzing the heat cogeneration aspects. Developed model is validated and verified by using archive data gained from researches...
-
Modelling of Nuclear Power Plant Steam Turbine
PublicationThe paper describes the approach to a Nuclear Power Plant steam turbine modelling which would enable on-line optimal process control (model based) and diagnosis over wide range of operating conditions caused by changing power demand. Presented model is static, multivariable and nonlinear. Such model enables analyzing the heat cogeneration aspects. Developed model is validated and verified by using archive data gained from researches...
-
Determination of Failure Causes of a Steam Turbine Casing
PublicationThe paper presents results of research and failure analysis undertaken to determine failure causes of a steam turbine casing. After 130,000 hours of service the crack in a outer shell of the turbine casing was found. The inner shell of the casing was made of cast steel grade G21CrMoV5-7, and the outer shell of grade G20CrMo4-5. Following research were performed in order to determine causes of the casing failure: chemical analysis;...
-
Comparing combined gas tubrine/steam turbine and marine low speed piston engine/steam turbine systems in naval applications
PublicationPorównano układy napędowe okrętowe kombinowane turbina gazowa- turbina parowa oraz spalinowy okrętowy silnik tłokowy wolnoobrotowy - turbina parowa. Porównywano moce oraz zużycie paliwa oraz parametry pary świeżej układu turbiny parowej.
-
Kinetic analysis of the stage for a high speed steam turbine
PublicationThis article analyzes possibilites of resonances within a control stage for a high speed steam turbine. This stage hase been based on assembling of a single blade to a rotating disk and increasing of rigidity of the system by using of a bandage. In the analysis will be nd a possiblity of resonance frequency, and mistuning by showing safety working ranges. The calculations have bean used the3D modal and harmonic analysis by the...
-
Dynamic model of nuclear power plant steam turbine
Publication -
A Computational Analysis of the Aerodynamic and Aeromechanical Behavior of a Thermo-Well for Steam Temperature Measurement in a Steam Turbine
PublicationThe goal of the paper is twofold: firstly, it presents computational fluid dynamics analysis for finding maximum unsteady flow forces (and their frequencies) acting on a thermo-well for measuring steam temperature in a steam turbine control stage and secondly, it presents computational solid dynamics analysis of possibility of entry into resonance of the thermowell structure. There have been analyzed two cases of flow with changing...
-
On the possible increasing of efficiency of ship power plant with the system combined of marine diesel engine, gas turbine and steam turbine at the main engine - steam turbine mode of cooperation
PublicationW pracy przedstawiono koncepcję układu kombinowanego okrętowego dużej mocy złożonego z silnika głównego tłokowego oraz skojarzonych z nim turbiny gazowej mocy i układu turbiny parowej, wykorzystujących energię zawartą w spalinach wylotowych silnika głównego tłokowego. Rozpatrywano układ kombinowany układ złożony z silnika spalinowego tłokowego skojarzony z układem turbiny parowej. Podano algorytm i obliczenia poszczególnych podukładów:...
-
INFLUENCE OF INLET GEOMETRY ON THE EFFICIENCY OF 1MW STEAM TURBINE
PublicationThe process of the design of the 1MW steam turbine includes designing the stator and rotor blades, the steam turbine inlet and exit, the casing and the rotor. A turbine that operates at rotation speeds other than 3000 rpm requires a gear box and generator with complex electronic software. This paper analyses the efficiency of eight turbine variants, including seven inlet geometries and three stages of stator as well as an eight...
-
On the possible increasing of efficiency of ship power plant with the system combined of marine diesel engine, gas turbine and steam turbine in case of main engine cooperation with the gas turbine fed in parallel and the steam turbine
PublicationW pracy przedstawiono koncepcję układu kombinowanego okrętowego dużej mocy złożonego z wiodącego silnika głównego spalinowego silnika tłokowego i skojarzonych z nim turbiny gazowej mocy i układu turbiny parowej, wykorzystujących energię zawartą w spalinach wylotowych głównego silnika spalinowego. Rozpatrzono wariant układu kombinowanego, w którym główny jest silnik tłokowy skojarzony z turbiną gazową mocy i układem turbiny parowej,...
-
On the possible increasing of efficiency of ship power plant with the system combined of marine diesel engine, gas turbine and steam turbine in case of main engine cooperation with the gas turbine fed in series and the steam turbine
PublicationW pracy przedstawiono koncepcję układu kombinowanego okrętowego dużej mocy złożonego z wiodącego silnika głównego silnika spalinowego tłokowego oraz skojarzonych z nim turbiny gazowej mocy i układu turbiny parowej, wykorzystujących energię zawartą w spalinach wylotowych silnika spalinowego. Rozpatrywano wariant układu kombinowanego, którym turbina mocy jest zasilana szeregowo spalinami wylotowymi. Podano algorytm i obliczenia...
-
Optimisation of turbine shaft heating process under steam turbine run-up conditions
PublicationAn important operational task for thermal turbines during run-up and run-down is to keep the stresses in the structural elements at a right level. This applies not only to their instantaneous values, but also to the impact of them on the engine lifetime. The turbine shaft is a particularly important element. The distribution of stresses depends on geometric characteristics of the shaft and its specific locations. This means a groove manufactured...
-
The thermal effort during marine steam turbine flooding with water
PublicationThe work discussed an extreme case of cooling a steam turbine. The ship's steam turbine was used as an example. In marine transport units with low-speed engines dominate, however, there are also units with steam turbines. An example of analysed marine steam turbine is shown in Fig. 1. When considering the issue of cooling steam turbines, it is necessary to estimate the extreme conditions that may occur during operation of the turbine....
-
Application of Artificial Neural Networks in Investigations of Steam Turbine Cascades
PublicationZaprezentowano wyniki badań numerycznych zastosowania sieci neuronowych przy obliczeniach przepływów w palisadach turbin parowych. Na podstawie uzyskanych wyników wykazano, że sieci neuronowe mogą być używane do szacowania przestrzennego rozkładu parametrów przepływu, takich jak entalpia, entropia, ciśnienie czy prędkość czynnika w kanale przepływowym. Omówiono również zastosowania tego typu metod przy projektowaniu palisad, stopni...
-
Control of the wind turbine generator
PublicationWind power system consists of two main parts: wind turbine and electrical generator. Wind turbine converts the energy of the flowing air into mechanical energy, next generator converts this energy into electrical energy that is sent to the power system. These two processes should be realized with maximum efficiency and the following requirements for the control system can be formulated: opti-mal wind power conversion, compensation...
-
Simplified, multiregional fuzzy model of a nuclear power plant steam turbine
PublicationPower systems, including steam turbines and synchronous generators, are complex nonlinear systems with parameters varying over time. The paper presents the developed simplified, multiregional fuzzy model of the steam turbine of a nuclear power plant turbine generator set and compares the results with a full nonlinear model and commonly used linear input-output model of a steam turbine. The proposed model consist of series of linear...
-
OPTIMIZATION OF THE LAST STAGE OF GAS-STEAM TURBINE USING A HYBRID METHOD
PublicationThis paper relates to the CFD calculation of a new turbine type which is in the phase of theoretical analysis, because the working fluid is a mixture of steam and gas generated in wet combustion chamber. At first, this article concentrates on a possibility of streamlining the flow efficiency of a last stage of axial turbine working on gas-steam mixture using a hybrid of the particle swarm optimization algorithm with the Nelder-Mead...
-
On design and analysis of flow characteristics of the last stage of gas-steam turbine
PublicationResearch regarding blade design and analysis of flow have been conducted for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics (CFD) and computational flow mechanics (CFM). Currently a combination of mentioned methods is used for design of turbine blades. These methods enabled us to improve flow efficiency...
-
SELECTED COMBINED POWER SYSTEMS CONSISTED OF SELFIGNITION ENGINE AND STEAM TURBINE
PublicationThis paper presents optimization of selected combined diesel engine-steam turbine systems. Two systems: the system combined with waste heat one-pressure boiler only and its version containing additionally low-pressure boiler proper feeding degasifier and the system of two-pressure cycle, were taken into considerations. Their surplus values of power output and efficiency associated with utilization of waste heat contained in piston...
-
Stabilization of the titanium vibration damping wires in the steam turbine blades system
PublicationPrzedstawiono metody stabilizacji drutów tłumiących w systemie łopatkowym turbin parowych. Na podstawie badań eksperymentalnych mikrostruktury i własności mechanicznych wykazano przydatność metody stabilizacji na gorąco drutów tłumiących wykonywanych ze stopu tytanu WT3-1.
-
Power augmentation of PGE Gorzow's gas turbine by steam injection - thermodynamic overview
PublicationThe impact of steam injection upon a gas turbine and a combined power plant performance has been investigated. This article describes and summarizes possibilities of modification for current gas turbine in PGE Gorzow power plant into the Cheng cycle. Our modification deals with a thermal cycle, in which steam produced in a heat recovery steam generator is injected into the gas turbine's combustion chamber. It has been proved that...
-
A Concept for Safe and Less Expensive Acceleration of a Marine Steam Turbine Start-up
PublicationThis paper analyses the issue of accelerated start-up of a marine steam turbine, which is an important problem because the start-up of a steam machine involves the combustion of fuel that is not transformed into useful energy. To find novel technologies that offer improvements in this aspect is essential due to restrictions on reducing ship emissions. Thus, the shorter the start-up time, the better for the environment and economy....
-
Feasibility of combined diesel engine - steam turbine in power station operating in the maritime
PublicationCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. Currently, the efficiency of such engines amounts to 45-50%. With such a large power unit, exhaust gases leaving the engine contain very large quantities of heat available for further treatment. Exhaust gases from the piston engine contain about 25% of the heat supplied to the engine in the fuel. Using the...
-
Steam turbine as the main ship propulsion. More than a hundred years at sea.
PublicationPrzedstawiono rys historyczny rozwoju okrętowych turbin parowych. Omówiono główne rozwiązania konstrukcyjne podstawowych elementów parowych siłowni turbinowych i współczesne tendencje i perspektywy rozwoju tego napędu.
-
Influence of the steam within seals and glands of the turbine on its rotor motion stability.
PublicationPrzedstawiono metodę obliczania charakterystyk dynamicznych wpływu parowych uszczelnień turbin na ich dynamikę i stateczność ruchu wirników. Zarysowano model ''masowy'' uszczelnienia. Podano przykłady zastosowań.
-
Identification of inertia, damping and stiffness parameters for low pressure steam turbine framework.
PublicationW pracy przedstawiono metodę identyfikacji masy tłumienia i sztywności kadłuba części niskoprężnej turbiny parowej 200MW.
-
Unsteady aerodynamic forces acting on the rotor blades in the turbine stagewith steam extraction.
PublicationPrzeprowadzono analizę niestacjonarnych wymuszeń działających na łopatki wirnikowe w stopniu z upustem turbiny 13UC100. Niestacjonarne siły zostały wyznaczone dla 4 punktów pracy upustu. Wskazano na możliwą przyczynę zaistniałego zniszczenia łopatek wirnikowych turbiny.
-
Technical and economical analysis of combined cycles of gas turbine -steam turbine on pipeline compressor stations. Part II - Economic analysis
PublicationW pracy przedstawiono zagadnienie nadbudowy zespołów turbosprężarkowych, znajdujących się na tłoczni gazu ziemnego, odzyskowymi blokami parowymi. W analizie tego przedsięwzięcia wzięto pod uwagę kilka wariantów konfiguracji układu parowego oraz kilka wariantów uwzględniających zmienność obciążenia turbin gazowych napędzających kompresory. Dla układu parowego dobrano wszystkie podstawowe parametry, a następnie wykonano obliczenia...
-
Technical and economical analysis of combined cycles of gas turbine - steam turbine on pipeline compressor stations. Part I - Technical analysis
PublicationW pracy przedstawiono zagadnienie nadbudowy zespołów turbosprężarkowych, znajdujących się na tłoczni gazu ziemnego, odzyskowymi blokami parowymi. W analizie tego przedsięwzięcia wzięto pod uwagę kilka wariantów konfiguracji układu parowego oraz kilka wariantów uwzględniających zmienność obciążenia turbin gazowych napędzających kompresory. Dla układu parowego dobrano wszystkie podstawowe parametry, a następnie wykonano obliczenia...
-
Technical and economical analysis of combined cycles of gas turbine - steam turbine on pipeline compressor stations. Part II - Economic analysis
PublicationW pracy przedstawiono zagadnienie nadbudowy zespołów turbosprężarkowych, znajdujących się na tłoczni gazu ziemnego, odzyskowymi blokami parowymi. W analizie tego przedsięwzięcia wzięto pod uwagę kilka wariantów konfiguracji układu parowego oraz kilka wariantów uwzględniających zmienność obciążenia turbin gazowych napędzających kompresory. Dla układu parowego dobrano wszystkie podstawowe parametry, a następnie wykonano obliczenia...
-
Design and computational fluid dynamics analysis of the last stage of innovative gas-steam turbine
PublicationResearch regarding blade design and analysis of flow has been attracting interest for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics and computational flow mechanics. Currently a combination of mentioned methods is used for the design of turbine blades. These methods enabled us to improve flow efficiency...
-
Complementary studies of residual stress distribution of repaired power plant steam turbine casing
PublicationRozkład i poziom naprężeń własnych w korpusach turbin badano za pomocą efektu Barkhausena oraz metodą nawiercania otworów. Badano również twardość. Korpusy były reperowane metodą zaspawania. Wykazano, iż zastosowana technologia nie wprowadza naprężeń o poziomie zagrażającym dalszej ekploatacji korpusu.
-
Possible efficiency increasing of ship propulsion and marine power plant with the system combined of marine diesel engine, gas turbine and steam turbine
PublicationW rozdziale przedstawiono koncepcję układu kombinowanego okrętowego lub morskiej pływającej elektrowni dużej mocy złożonego z silnika głównego tłokowego oraz skojarzonych z nim turbiny gazowej mocy i układu turbiny parowej, wykorzystujących energię zawartą w spalinach wylotowych silnika głównego tłokowego. Rozpatrywano możliwości zastosowania takich układów w układach okrętowych z punktu widzenia sprawnościowego. Podano możliwości...
-
PARAMETRIC ANALYSIS OF THE EFFICIENCY OF THE COMBINED GAS-STEAM TURBINE UNIT OF A HYBRID CYCLE FOR THE FPSO VESSEL
PublicationA thermal diagram of the combined gas‒steam turbine unit of a hybrid cycle, which is an energy complex consisting of a base gas turbine engine with a steam turbine heat recovery circuit and a steam-injected gas turbine operating with overexpansion, is proposed. A mathematical model of a power plant has been developed, taking into consideration the features of thermodynamic processes of simple, binary, and steam-injected...
-
Revalorisation of the Szewalski’s concept of the law of varying the last-stage blade retraction in a gas-steam turbine
PublicationThe article presents the implementations of the free vortex law to the blade of the last stage of a gas-steam turbine. First, a thermodynamic analysis was carried out, determining the parameters at the inlet, then the number of stages of the high and low-pressure part of the turbine was constructed, together with the kinematics and velocity vectors for subsequent stages of the axial turbine. The last step of article was to take...
-
The system combined of low-speed marine diesel engine and steam turbine in ship propulsion applications
PublicationPrzedstawiono koncepcje okrętowego układu kombinowanego silnik wolnoobrotowy tłokowy- turbina parowa, wykorzystującego ciepło zawarte w spalinach wylotowych.Porównano układ kombinowany dużej mocy dla dwóch silników tłokowych porównywalnych mocy z punktu widzenia termodynamicznego.
-
Preliminary design of the last stage of supercritical steam turbine and proposition of anti-erosion coating for blades surface
PublicationIn this article a preliminary design of the last stage of supercritical steam turbine has been presented. A computational model of supercritical thermal cycle has been created in order to determine steam parameters at the stage inlet and outlet. The model was based on the structure of German coal-fired power plant Datteln 4. Further steam-flow parame-ters and dimensions of stator and rotor blades have been calculated analytically....
-
Application of data driven methods in diagnostic of selected process faults of nuclear power plant steam turbine
PublicationArticle presents a comparison of process anomaly detection in nuclear power plant steam turbine using combination of data driven methods. Three types of faults are considered: water hammering, fouling and thermocouple fault. As a virtual plant a nonlinear, dynamic, mathe- matical steam turbine model is used. Two approaches for fault detection using one class and two class classiers are tested and compared.
-
Investigation of ecological parameters of a gas turbine combustion chamber with steam injection for the floating production, storage, and offloading vessel
PublicationThe article is dedicated to the investigation of the possibility of using the contact type gas turbine cycle with steam injection into the combustion chamber for the floating production, storage, and offloading vessel in order to increase the specific power and efficiency and reduce emissions of toxic components. A new approach is proposed, associated with the use of the two-stage injection of superheated steam into a gas turbine...
-
Operating and economical conditions of cooling water control for marine steam turbines condensers
PublicationW pracy dokonano analizy ekonomicznej i eksploatacyjnej sterowania pracą pomp wody chłodzącej skraplacze turbin okrętowych. Wzięto pod uwagę cechy konstrukcyjne pomp wody chłodzącej skraplacze główne i najnowsze wyniki badań dla takich pomp w zastosowaniach lądowych. Uwagę skupiono przede wszystkim na turbinowych parowych siłowniach okrętowych.
-
Neuronowa symulacja temperatury i ciśnienia pary w upuście parowego bloku energetycznego = Neural simulation of pressure and temperature fluctuations at steam extraction of power units with steam turbine
PublicationW artykule przedstawiono metodę symulacji neuronowej dla zastosowań w diagnostyce on-line bloków energetycznych. Model neuronowy opiera się na statycznych jednokierunkowych sieciach neuronowych (SSN) oraz na danych z parowego bloku energetycznego o mocy 200 MW. SSN obliczają wartości referencyjne parametrów cieplno-przepływowych dla aktualnego obciążenia obiektu. Określono wpływ architektury sieci i danych uczących na jakość symulacji...
-
Numbers, Please: Power- and Voltage-Related Indices in Control of a Turbine-Generator Set
PublicationThis paper discusses the proper selection and interpretation of aggregated control performance indices values mirroring the quality of electrical energy generation by a turbine-generator set cooperating with a power system. Typically, a set of basic/classical and individual indices is used in energy engineering to ensure the mirroring feature and is related to voltage, frequency and active or reactive power deviations from their...
-
Reduction of CO2 Emissions from Offshore Combined Cycle Diesel Engine-Steam Turbine Power Plant Powered by Alternative Fuels
PublicationDiverse forms of environmental pollution arise with the introduction of materials or energy that exert adverse effects on human health, climate patterns, ecosystems, and beyond. Rigorous emission regulations for gases resulting from fuel combustion are being enforced by the European Union and the International Maritime Organization (IMO), directed at maritime sectors to mitigate emissions of SOx, NOx, and CO2. The IMO envisions...