Search
Search results for: TILTING PAD BEARINGS
-
Tribological model of porous bearings with particular attention given to the lubricant lubricity
PublicationThe friction and wear problems, accompanying all the tribological systems, lead to reduced service life. In order to prevent such situation, it is necessary to maintain fluid friction, which improves durability of all friction nodes in a tribological system. In the paper, the tribological system consists of porous bearings and the model deals with their weakest spots - the oil outflow points in the porous wall. A kinetic model...
-
Marine propeller shaft bearings under low-speed conditions: water vs. oil lubrication
PublicationThe bearings used in shipbuilding, hydropower, and water pumps have undergone a metamorphosis in recent decades. Because of environmental regulations, lubrication with grease or mineral oil is prohibited. Thus, the standard solutions include water-lubricated bearings with polymer bushings or sealed systems lubricated with oil. When properly designed, assembled, and operated, bearings can operate reliably for years. However, specific...
-
Shaking table experimental study on the effectiveness of polymer bearings for seismic isolation of structures
PublicationSeismic isolation has been recognised to be a very effective way of protecting structures from damage during earthquakes. It allows us to extend the natural period of the structure and therefore avoid resonance with the ground motion. Moreover, by increasing damping in the isolation devices, more energy can be dissipated and thus the structural response can be further reduced. The aim of this paper is to show the results of the...
-
Novel condition monitoring of induction motor bearings via motor current signature analysis
PublicationThe paper authors are researching the assessment of bearing conditions in induction motors. The methods developed by the authors are based on measurements and analysis of the motor supply current, which is particularly attractive in the absence of access to the engine. The article provides an overview of selected methods of induction motor bearings diagnostic based on Motor Current Signature Analysis (MCSA). However, there is no...
-
POSSIBILITY OF ASSESSMENT OF OPERATION OF SLIDING BEARINGS IN PISTON-CRANK MECHANISMS OF DIESEL ENGINES WITH REGARD TO LOAD AND TIME OF CORRECT WORK OF THE BEARINGS BY APPLYING ACOUSTIC EMISSION AS A DIAGNOSTIC SIGNAL
PublicationAbstract: The paper presents a possibility of determining (assessing) operation of sliding bearings with multilayer bushings in crank-piston mechanisms of diesel engines. Properties of load and wear, particularly fatigue and abrasive, are characterized in general. Acoustic emission as a diagnostic signal was proved to be useful for detection of the wear of sliding and barrier layers. Results of measurements of acoustic emission...
-
Polymeric Bearings as a new base isolation system suitable for mitigating machine-induced vibrations
PublicationThe present paper summarizes the preliminary results of the experimental shaking table investigation conducted in order to verify the effectiveness of a new base isolation system consisting of Polymeric Bearings in reducing strong horizontal machine-induced vibrations. Polymeric Bearing considered in the present study is a prototype base isolation system, which was constructed with the use of a specially prepared flexible polymer...
-
WATER LUBRICATED MAIN SHAFT BEARINGS - MODERN SOLUTION FOR HYDROPOWER INDUSTRY - Experimental and theoretical studies
PublicationWater-lubricated bearings are finding increasingly wide use in various branches of industry. As such, they may also be encountered in hydro power industry. They are also increasingly frequently employed in bearing systems of marine shaft propulsions and water pumps [1]. This rising popularity is due to a number of reasons [2]. First of all, their simple construction has direct impact on the level of pricing which is usually quite...
-
Application of acoustic emission for detection of fatigue microdemage in main and crank bearings for diesel engines
PublicationThe article presents reasons for applying the acoustic emission (AE) to detect fatigue microdamage in main bearings and crank bearings of ship main engines. Problem of determination of the fatigue life for slide bearing bushes was characterized in general. There were demonstrated properties of the objects of research, which were bushings made of the MB58 alloy, as well as an overall description of the research. It was shown that...
-
Sliding bearings with sintered bronze bush lubricated by contaminated water with solid particles – Theoretical and experimental studies
PublicationSliding journal bearings lubricated with water coming directly from the environment are a solution used in shipbuilding, pumps and hydropower. However, the working fluid or surrounding water cannot always be filtered because of design limitations, which often causes the problem of premature wear of these sensitive bearings. The research conducted made it possible to assess the wear of sliding bearings lubricated with water containing...
-
POSSIBILITY OF IDENTIFICATION OF TECHNICAL CONDITION OF BEARINGS FOR SELF-IGNITION ENGINES BY APPLICATION OF ACOUSTIC EMISSION AS A DIAGNOSTIC SIGNAL
PublicationThis paper presents the results of empirical studies where the acoustic emission (AE) method was applied to identify the technical condition of sliding surfaces of main and crank bearings for main diesel engines. The test results indicate that the measurements of the AE parameters allow the technical condition identification for bearings of this type. The results refer to the measurements of the parameters for AE generated in the...
-
The dynamic performance analysis of the Micro-turbine's rotor supparted on slide and roling element bearings
PublicationThis article presents the results of investigations of dynamic characteristics of a small-dimension rotor with slide and rolling element bearings. The object of investigations was the rotor-bearing system designed for the ORC based low-power steam micro-turbine. The investigations were performed using MESWIR series programs, as well as commercial FEA software ABAQUS and MADYN 2000. The results of modal analysis of the micro-rotor...
-
Polymer journal bearings behaviour research under limited lubrication and cooling conditions conducted on high torque test rig
PublicationPolymer journal bearings are frequently used as a water-lubricated bearings of small marine units’ propeller shafts . Choice of these bearings is based on their simple construction and relatively low purchase and maintenance costs. Although properly designed and installed water lubricated bearings may well last for over a decade, rapid wear or failure of these bearings can be observed...
-
The Experimental Determination of Bearings Dynamic Coefficients in a Wide Range of Rotational Speeds, Taking into Account the Resonance and Hydrodynamic Instability
PublicationMethods for the experimental determination of dynamic coefficients are commonly used for the analysis of various types of bearings, including hydrodynamic, aerodynamic and foil bearings. There are currently several algorithms that allow estimating bearing dynamic coefficients. Such algorithms usually use various excitation techniques applied to rotor–bearings systems. So far only a small number of scientific publications show how...
-
Some fundamental aspects of self-levitating sliding contact bearings and their practical implementations
PublicationIn this study, fundamental aspects and mechanisms of acoustic levitation together with governing equations are presented first. Then, the acoustic levitation phenomenon is considered as a new way to design air suspension systems capable of self-levitation. A particular emphasis is laid on journal bearings and their specific geometrical configuration. A practical feasibility of using acoustic levitation to separate contacting surfaces...
-
Comparison of the characteristics of journal bearings determined according to ISO 7902:2020 and obtained by other methods
PublicationThe article presents selected characteristics of journal bearings calculated with the use of various methods and compared to the results obtained with application of the basic bearing characteristics calculation procedure, as described in the ISO 7902:2020 standard. Additionally, the presented calculation results were compared with the parameters measured during experimental tests of the sliding bearings, working under loads and...
-
Supply current signal and artificial neural networks in the induction motor bearings diagnostics
PublicationThis paper contains research results of the diagnostics of induction motor bearings based on measurement of the supply current with usage of artificial neural networks. Bearing failure amount is greater than 40% of all engine failures, which makes their damage-free operation crucial. Tests were performed on motors with intentionally made bearings defects. Chapter 2 introduces the concept of artificial neural networks. It presents...
-
Experimental research on water lubricated marine stern tube bearings in conditions of improper lubrication and cooling causing rapid bush wear
PublicationWater lubricated bearings are popular in sliding bearings of marine propeller shafts, turbines and pump shafts. Such popularity is partly due to their simple construction which also means a relatively affordable price. In practical experience one may also observe cases of rapid wear or even malfunctions of this bearings, some of which may be caused by insufficient flow of lubricant leading to overheating. The conducted...
-
Behaviour of Asymmetric Structure with Base Isolation Made of Polymeric Bearings
PublicationEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Seismic excitations cause a lot of damage in a wide variety of ways, leaving thousands of casualties in their wake. Due to randomness of earthquake occurrence, lack of visible causes and their power of destructiveness, structural engineers need to develop new technical solutions and protection systems against...
-
Advanced Hysteretic Model of a Prototype Seismic Isolation System Made of Polymeric Bearings
PublicationThe present paper reports the results of acomprehensive study designed to verify the effectiveness of an advanced mathematical model in simulating the complex mechanical behaviour of a prototype seismic isolation system made of polymeric bearings (PBs). Firstly, in order to construct the seismic bearings considered in this research, a specially prepared flexible polymeric material with increased damping properties was employed....
-
Induction Motor Bearings Diagnostic Using MCSA and Normalized Tripple Covariance
PublicationDiagnosis of induction motors, conducted remotely by measuring and analyzing the supply current is attractive with the lack of access to the engine. So far there is no solution, based on analysis of current, the credibility of which allow use in industry. Statistics of IM bearing failures of induction motors indicate, that they constitute more than 40% of IM damage, therefore bearing diagnosis is so important. The article provides...
-
Influence of bush wear in water lubricated marine stern tube bearings with shaft misalignment
PublicationWater lubricated propeller shaft bearings are frequently employed on modern ships due to their advantages such as durability, simplicity and low price. Specific working conditions on ships cause shaft misalignment which often results in rapid wearing of bush and shaft. Shaft misalignment could be an effect of manufacturing or assembly faults but sometimes it appears due to hull or shaft deformation. The wearing process has influence...
-
Is it possible to predict performance of large thrust bearings on the basis of the results of experiments on smaller bearings?
PublicationTreścią referatu jest analiza możliwości przeniesienia wyników badań modelowych z małych hydrodynamicznych łożysk wzdłużnych do określenia własności łożysk o dużych rozmiarach. Posłużono się analizą wymiarową do określenia wymaganych współczynników skali, których zachowanie podczas badania łożyska modelowego, zapewnia jego podobieństwo do łożyska o dużych rozmiarach. Uzyskane wyniki poddano dyskusji.
-
Evaluation of apparent Young׳s modulus of the composite polymer layers used as sliding surfaces in hydrodynamic thrust bearings
PublicationHydrodynamic bearings with a polymer sliding layer are able to operate in severe conditions, mainly due to favorable properties of the polymers. The goal of this research was to evaluate apparent Young׳s modulus of two types of the polymer composite layers used for sliding surfaces in hydrodynamic bearings, as a function of temperature. The Young׳s modulus was evaluated on the basis of compression tests carried out on samples obtained...
-
Effectiveness of a mathematical model in simulating nonlinear mechanical behaviour of a seismic isolation system made of polymeric bearings
PublicationThe present study was focused on determining the effectives of a nonlinear mathematical model in simulating complex mechanical behaviour of a seismic isolation system made of Polymeric Bearings. The proposed mathematical model defines the lateral force as a nonlinear function of the shear displacement and the deformation velocity. The effectiveness of the proposed mathematical model was verified by comparing the seismic response...
-
Design and Optimization of Metamaterial-based Highly-isolated MIMO Antenna with High Gain and Beam Tilting Ability for 5G Millimeter Wave Applications
PublicationThis paper presents a wideband multiple-input multiple-output (MIMO) antenna with high gain and isolation, as well as beam tilting capability, for 5G millimeter wave (MMW) applications. A single bow-tie antenna fed by a substrate-integrated waveguide (SIW) is proposed to cover the 28 GHz band (26.5–29.5 GHz) with a maximum gain of 6.35 dB. To enhance the gain, H-shaped metamaterial (MM)-based components are incorporated into the...
-
Behaviour of asymmetric structures with base isolation made of Polymeric Bearings
PublicationEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Seismic excitations cause a lot of damage in a wide variety of ways, leaving thousands of casualties in their wake. During the last few years alone, the world has witnessed many major earthquakes, five of which have caused far-reaching consequences of a national scale for Haiti (January 2010), Chile (February...
-
Ring thruster with magnetic bearings
Publication.
-
MCSA with Normalized Triple Covariance as a bearings diagnostic indicator in an induction motor
PublicationStatistics of bearing failures in induction motors indicate, that they constitute more than 40% of IM damage, therefore bearing diagnosis is very important. Vibration methods for bearing diagnostics have one major disadvantage - they require the availability of the machine for sensors installation. This is the reason for seeking new methods based on motor supply current analysis. Diagnosis of induction motors, conducted remotely...
-
Reduction of vibrations of steel structure models with Polymeric Bearings - experimental study
PublicationEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Therefore, designing earthquake protective systems has become an extremely challenging problem in civil engineering. Base isolation is one of the most popular and widely adopted methods of protecting structures against earthquake forces. The present paper reports the results obtained from the shaking table experimental...
-
Current based Normalized Triple Covariance as a bearings diagnostic feature in induction motor
PublicationDiagnosis of induction motors, conducted remotely by measuring and analyzing the supply current is attractive with the lack of access to the engine. So far there is no solution, based on analysis of current, the credibility of which allow use in industry. Statistics of IM bearing failures of induction motors indicate, that they constitute more than 40% of IM damage, therefore bearing diagnosis is so important. The article provides...
-
The experimental identification of the dynamic coefficients of two hydrodynamic journal bearings operating at constant rotational speed and under nonlinear conditions.
PublicationHydrodynamic bearings are commonly used in ship propulsion systems. Typically, they are calculated using numerical or experimental methods. This paper presents an experimental study through which it has been possible to estimate 24 dynamic coefficients of two hydrodynamic slide bearings operating under nonlinear conditions. During the investigation, bearing mass coefficients are identified by means of a newly developed algorithm....
-
WYKORZYSTANIE CHROMATOGRAFII JONOWEJ (IC-PAD) W ANALITYCE JONÓW CYJANKOWYCH OBECNYCH W PESTKACH POLSKICH JABŁEK I MORELI
PublicationJony cyjankowe zawarte w próbkach pestkach jabłek pochodzą z rozpadu glikozydów cyjanogennych. Główne rośliny jadalne, w których występują glikozydy cyjanogenne to migdały, sorgo, maniok, owoce pestkowe i pędy bambusa. Cyjanoglikozydy występują często w częściach roślin niespożywanych przez człowieka np. pestkach moreli. Jednakże, ze względu na domniemane właściwości antynowotworowe pestki moreli są dostępne w sklepach ze zdrową...
-
INFLUENCE OF SOLID PARTICLE CONTAMINATION ON THE WEAR PROCESS IN WATER LUBRICATED MARINE STRUT BEARINGS WITH NBR AND PTFE BUSHES
PublicationThis paper reports on a study of the influence of solid particle contamination on the wear process in water-lubricated slide bearings (steel-acrylonitrile-butadiene rubber (NBR) and steel- polytetrafluoroethylene (PTFE)). To compare the wear of the shaft journal and bushes (NBR and PTFE) when lubricated with fresh water and contaminated water, an experiment was carried out to identify key factors that influence the state of wear...
-
Induction motor bearings diagnostic indicators based on MCSA and normalized triple covariance
PublicationInduction motors are one of the most widely used electrical machines. Statistics of bearing failures of induction motors indicate, that they constitute more than 40% of induction motor damage. Therefore, bearing diagnosis is so important for trouble-free work of induction motors. The most common methods of bearing diagnosis are based on vibration signal analysis. The main disadvantage of those methods is the need for physical access...
-
The use of Acoustic Emission to identification damages bearings the main and crank engines about the automatic ignition
PublicationThe article describes the laboratory tests, which make the first stage of the study concerning the use of the AE method to determine the technical state of the slide bearings in engines with self-ignition. The aim of the present tests was to compare the recorded signals in relation to the technical state of the material of the bearing bush and to check the possibility of using the AE method in determining the transition moment...
-
Three-dimensional CFD modeling of thermal behavior of a disc brake and pad for an automobile
Publication -
Special Issue on Sliding Contact Bearings
Publication -
Fatigue investigation of plain journal bearings
PublicationW artykule przedstawiono wybrane wyniki badań nad wytrzymałością zmęczeniową warstw ślizgowych w panwiach łozysk poprzecznych, prowadzonych w laboratorium tribologicznym Katedry Konstrukcji i Eksploatacji Maszyn Politechniki Gdańskiej. Opisano stanowiska badawcze i metodykę planowania eksperymentów oraz procedurę opracowywania wyników testów zmęczeniowych. Przedstawiono zamierzenia badawcze w zakresie przedmiotowych badań zmęczeniowych.
-
Structural properties of foil bearings: a closed-form solution validated with finite element analysis
PublicationFluid film thickness in a compliant foil bearing is greatly influenced by the deflection of the bearing structure. Therefore, in order to properly model performance of a foil bearing, it is mandatory that the deflection of the compliant bearing structure due to the generated hydrodynamic pressure is determined accurately. This article proposes an easy-to-use two-dimensional model, which takes into account detailed geometry of the...
-
Comparative wear test of journal sliding bearings with sintered bronze and Babbitt alloy bushes lubricated by environmentally acceptable/adapted lubricants (EAL)
PublicationA growing awareness of the negative effects of mineral oils on the natural environment has resulted in the introduction of new regulations related to environmental protection. One of these regulations requires the use of environmentally acceptable/adapted lubricants (EAL) to lubricate marine main shaft bearings, in place of the mineral lubricating oils that have been used for decades. Classification Societies, which supervise...
-
Research on water lubricated main shaft bearings in conditions of improper lubrication and cooling conducted on high torque real-life scale bush test rig
PublicationWater lubricated polymer bushes find increasingly popular use in the sliding bearings of marine propellers, water turbines and pump shafts. Such popularity is partly due to their simple construction which also means relatively affordable price. In addition, properly designed and installed water lubricated bearings may well last for over a decade. However, in practical experience one may also observe cases of rapid wear...
-
THE INFLUENCE OF HOUSING ARRANGEMENT AND INTERFERENCE ON PRELOAD AND THEORETICAL LIFETIME OF A SYSTEM OF TAPER ROLLER BEARINGS OF A HIGH SPEED SHAFT OF A WIND TURBINE GEARBOX
PublicationA system of two taper roller bearings can carry loads with a high ratio of axial load to radial load. Such a system was proposed for a wind turbine gearbox following the poor durability of original bearing design with the aim of increasing durability. Because of size limits, a proposed system is composed of two different taper roller bearings. Standard manufacturers’ catalogues do not provide information on recommended preload...
-
ANALYSIS OF BEARING CLEARANCE AND WIDTH OF OIL GROOVE ON CHARACTERISTIC OF FLUID FILM IN HYDRODYNAMIC MAIN CRANKSHAFT BEARINGS
PublicationAbstract Paper represents analysis of influence of oil groove width and bearing clearance on characteristics of oil film in hydrodynamic journal main crankshaft bearing. Analysis was performed in purpose to define influence of bearing clearance and dimensions of oil groove on static characteristics and manufacturability of half shelf bearings in industrial high-volume production. Computer simulations was made using ARTbear program...
-
Comparable analysis of PID controller settings in order to ensure reliable operation of active foil bearings
PublicationIn comparison to the traditional solutions, active bearings offer great operating flexibility, ensure better operating conditions over a wider range of rotational speeds and are safe to use. In order to ensure optimum bearing performance a bearing control system is used that adapts different geometries during device operation. The selection of optimal controller parameters requires the use of modern optimization methods that make...
-
Temperature measurements in monitoring of large thrust bearings
PublicationW pracy przedstwiono krytyczną analizę aktualnych metod diagnostyki dużych hydrodnamicznych łożysk wzdłużnych hydrozespołów elektrowni wodnych. Wykazano niedostatki i zagrożenia płynące ze stosowania diagnostyki opartej na jednopunktowym pomiarze temperatury. Zaprezentowano wstępna koncepcję nowej metody diagnostycznej opartej na odwrotnym zagadnieniu przepływu ciepła (IPHC).
-
Temperature Measurements in Monitoring of Large Thrust Bearings
PublicationW pracy przedstawiono krytyczną ocenę popularnego systemu diagnostyki dużych łożysk wzdłużnych (np. łożysk nośnych hydrogeneratorów), w którym stosowany jest jednopunktowy pomiar temperatury w klockach łożyskowych. Stwierdzono, że taki układ pomiarowy nie pozwala na bezpieczną eksploatację łożysk, ponieważ posiada bardzo duże opóźnienie czasowe, nie daje informacji o lokalnych zagrożeniach, nie pozwala racjonalnie ustalić poziomów...
-
Temperature measurements in monitoring of large thrust bearings
PublicationW pracy przedstwiono krytyczną analizę aktualnych metod diagnostyki dużych hydrodnamicznych łożysk wzdłużnych hydrozespołów elektrowni wodnych. Wykazano niedostatki i zagrożenia płynące ze stosowania diagnostyki opartej na jednopunktowym pomiarze temperatury. Zaprezentowano wstępna koncepcję nowej metody diagnostycznej opartej na odwrotnym zagadnieniu przepływu ciepła.
-
The influence of polymer bearing material and lubricating grooves layout on wear of journal bearings lubricated with contaminated water
PublicationThe goal of the present paper is to investigate wear properties of journal sliding bearing operating in the conditions of contaminated water lubrication. Several bearing materials and bearing sleeve designs (differing in the axial grooves position and their shape) were tested experimentally under typical operating conditions in a dedicated test rig, which was equipped with a lubricating system, enabling lubrication with contaminated...
-
Properties comparison of rubber and three layer PTFE-NBR-bronze water lubricated bearings with lubricating grooves along full bush circumference based on experimental tests
PublicationWater lubricated bearings have been in industrial use for well over a century. During the last decade their traditional range has been expanded with new, modern products. Despite that fact, certain solutions continue to employ the standard rubber bearing with lubricating grooves located along entire bush circumference. The work presents experimental research conducted on comparable sliding bearings with lubrication grooves along...
-
Research and applications of active bearings: A state-of-the-art review
Publication