Filters
total: 1477
filtered: 520
Search results for: RSVP, DIAMETER
-
RSVP-TE as a reservation protocol for optical networks
PublicationIn this paper, we consider the reservation of optical resources problem. We implement extensions for RSVP-TE (Resource ReSerVation Protocol with Traffic Engineering Extension) to achieve the new functionality for optical resources reservation. Based on ASON/GMPLS architecture we examine an open source implementation KOM RSVP-Engine and extend its functionality according to ITU-T and IETF recommendations. The transport plane consists...
-
Modelling of Flow Process in Small Diameter Tubes.
PublicationW pracy zastosowano standardowš korelację wrzenia w przepływie (wyprowadzonš dla rur o konwencjonalnych wymiarach) do przypadków wrzenia w rurach o małych rednicach. Porównanie wyników z danymi literaturowymi wykazało nieużytecznoć tej korelacji. Wykazano zatem potrzebę prowadzenia badań podstawowych celem uzyskania korelacji pozwalajšcej umiejętnie przewidywać warunki wymiany ciepła w kanałach o małych rednicach.
-
Serwer Diameter w architekturze Proxy Mobile IPv6
PublicationW pracy przedstawiono mechanizmy współpracy serwera Diameter z systemem Proxy Mobile IPv6. Opisany został sposób integracji obu rozwiązań na potrzeby obsługi mobilności terminali ruchomych w sieci IPv6. W ramach realizowanych badań wykonano implementację opisanego systemu. Dla przygotowanej implementacji przeprowadzono szereg testów wydajnościowych uwzględniających parametry jakości QoS oraz QoE.
-
Experimental investigations on condensation in flow in small diameter channels
PublicationW pracy przedstawiono innowacyjne podejście do eksperymentalnych badań kondensacji w przepływie oraz omówiono wstępne wyniki badań eksperymentalnych kondensacji etanolu w pionowej rurce srebrnej o średnicy wewnętrznej 2.3 mm.
-
Modelling of flow boiling process in small diameter tubes.
PublicationW pracy zastosowano standardową korelację wrzenia w przepływie (wyprowadzoną dla rur o konwencjonalnych wymiarach) do przypadków wrzenia w rurach o małych średnicach. Porównanie wyników obliczeń z danymi literaturowymi wykazało nieużyteczność tej korelacji. Wykazano zatem potrzebę prowadzenia badań podstawowych celem uzyskania korelacji pozwalającej umiejętnie przewidywać warunki wymiany ciepła w kanałach o małych średnicach.
-
Burnout Investigation of Small Diameter Tubes Immersed in Nanofluids
PublicationThis paper deals with research into pool boiling critical heat flux (CHF) of water–Al2O3, water–TiO2 and water–Cu nanofluids on horizontal stainless steel tubes. The experiments were conducted under atmospheric pressure. Nanoparticles were tested at concentrations of 0.001%, 0.01%, 0.1% and 1% by weight. Ultrasonic vibration was used in order to stabilize the dispersion of the nanoparticles. Although dispersants were not used to...
-
Diabetes Mellitus
Publication -
Investigation of interaction between xanthene dye rhodamine B and metagenomic-derivated methylthioadenosine phosphorylase RSFP
PublicationIn the previous study we found that the expression of the metagenomic - derived methylthioadenosine phosphorylase gene (rsfp) in E. coli cells and the presence of rhodamine B in the growth medium were crucial for the pink fluorescence of one E. coli colony from Antarctic soil metagenomic library (Cieśliński et al., 2009). In this study, rsfp gene expression was induced by an arabinose promoter in an LMG194 E. coli strain and the...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symetrical phenomena. Their description however with a single correlation has yet to be suggested.In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the buble generetion is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such case...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena, however their description with a single correlation has yet to be suggested. In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the bubble generation is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such...
-
Review of Diameter protocol implementations for realization of communication in NGN networks
PublicationIn the paper Diameter protocol as well as its applications in the context of Next Generation Network (NGN) are described. Diameter message content and Attribute-Value Pairs (AVPs) concept are presented. Critical review of open source Diameter implementations is carried out. The performed analysis takes into consideration programming language, availability, support and documentation aspects. Basing on the review project fulfilling...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationIn the paper a method developed earlier by the first author is applied to calculations of heat transfer coefficient for inside tube condensation. The method has been verified using experimental data from literature on several fluids in different microchannels and compared to three well established correlations.
-
Ultra thick open tubular traps with an increased inner diameter.
PublicationPrzeanalizowano zagadnienia związane z zastosowaniem otwartych pułapek kapilarnych z grubym nieregularnym filmem polidimetylosiloksanu do wzbogacania lotnych związków organicznych. Przeprowadzone rozważania teoretyczne oraz prace eksperymentalne wykazały, że zwiększenie średnicy wewnętrznej pułapek może znacząco polepszyć ich właściwości. Dla danego natężenia przepływu próbki oraz danego stosunku objętości faz w pułapce, liczba...
-
Improved correlation for modelling of boiling processes in small diameter tubes.
PublicationW pracy przedstawiono rozważania na temat wrzenia w przepływie dwufazowym w kanałach o małej średnicy. Modyfikacji uległa korelacja zapostulowana wcześniej przez Mikielewicz i inni, poprzez wprowadzenie efektów związanych z napięciem powierzchniowym, także liczba konwekcyjna została poprawiona. Zastosowanie korelacji jest bardzo proste z uwagi na jej analityczną postać, co jest jej podstawową zaletą. Porównanie z danymi eksperymentalnymi...
-
Do positrons measure atomic and molecular diameters?
PublicationWe report on density functional calculations (DFT) of elastic integral scattering cross-sections for positron collisions with argon, krypton, nitrogen and methane. The long-range asymptotic polarization potential is described using higher-order terms going much beyond an induced dipole potential (−α / r 4) while the short-range interaction is modeled by two different forms of electron – positron correlation potential (Boroński-Nieminen...
-
Diameter sensitive effect in singlewalled carbon nanotubes upon acid treatment
Publication -
Influence of the substrate loading on the quality and diameter distribution of SWCNT in alcohol‐CVD
Publication -
Converting mixed plastics into mesoporous hollow carbon spheres with controllable diameter
Publication -
Reduced diameter distribution of single-wall carbon nanotubes by selective oxidation
Publication -
Experimental investigations on condensation in flow of HFE-7100 in small diameter channels
PublicationW pracy przedstawiono wyniki badań eksperymentalnych kondensacji czynnika HFE-7100 w minikanale o średnicy wewnętrznej 2.3 mm. Opisano również oryginalne podejście w prowadzeniu badań nad uzyskaniem lokalnych wartości współczynnika przejmowania ciepła podczas kondensacji w przepływie.
-
Experimental investigations on condensation in flow of HFE-7100 in small diameter channels
PublicationIn the paper the authors present investigations of flow condensation with the use of the HFE-7100 as a working fluid. The original and new approach to removing the heat from the channel was applied. The research was carried out using a wide-range real time observations, e.g. using infrared camera and stroboscope microphotography. This paper presents the details of experiment as well as the influence of heat and flow parameters...
-
Experimental and theoretical study of dryout in annular flow in small diameter channels
PublicationW pracy zaprezentowano badania eksperymentalne kryzysu wrzenia II rodzaju w kanałach o małej średnicy. Badania prowadzone były w rurach pionowych o średnicy 1.15 i 2.3 mm, w których badanym czynnikiem były płyny niskowrzące, takie jak SES36 i R123. W badaniach zastosowano nowoczesne techniki pomiarowe do określania lokalizacji kryzysu wrzenia na ściance kanału, np. kamerę termowizyjną. Na podstawie pozyskanych punktów eksperymentalnych...
-
The effect of cable duct diameter on the ampacity of high-voltage power cables
PublicationThe ampacity of power cables depends, among others, on the conditions of heat dissipation from the cable to the environment. Cables are usually laid directly in the ground, but in some sections, they may be placed in ducts, which adversely affects the ampacity of the cable line. The paper presents heat transfer phenomena for cables installed in pipe-type ducts filled with air. The effect of cable duct diameter on this ampacity...
-
The effect of circular saw blade clamping diameter on its resonant frequencies
PublicationIn this paper results of comparison of characteristic resonant frequencies of circular saw blades as a function of saw clamping diameter from the impact test are presented. Obtained results revealed that proportionally with the increase of the saw clamping diameter also the dynamical stiffness of the saw blade increased. As a consequence of that the resonant frequencies of the saw blade move to higher values. Moreover, with the...
-
The Effect of Circular Saw Blade Clamping Diameter on its Resonant Frequencies
PublicationIn this paper results of comparison of characteristic resonant frequencies of circular saw blades as a function of the saw clamping diameter from the impact test are presented. Obtained results revealed that proportionally with the increase of the saw clamping diameter also the dynamical stiffness of the saw blade increased. As a consequence of that the resonant frequencies of the saw blade move to higher values. Moreover, with...
-
Survivin expression in invasive pituitary gland adenomas with a diameter exceeding 20 mm
Publication -
Zeta potential, effective diameter and multimodal size distribution in oil/water emulsion
Publication -
Advances in engineering of diameter and distribution of the number of walls of carbon nanotubes in alcohol CVD
Publication -
Bulk synthesis of carbon-filled silicon carbide nanotubes with a narrow diameter distribution
Publication -
Cylindrical orifice testing in laminar flow with the orifice diameter ratio β = 0.5
PublicationThe paper presents the results of an experimental study of a cylindrical orifice with the orifice diameter ratio β = 0.5 and the flow opening length‑to‑diameter ratio L/d = 1, with hydraulic oil flowing in the DN50 measuring channel. The measurements of the values characterising the oil flow were made in the laminar flow regime, for the Reynolds numbers ranging between Re = 100 to 950. Based on the experimental tests, standard...
-
Experimental-Numerical Analysis of the Effect of Bar Diameter on Bond in Pull-Out Test
PublicationBar diameter is one of the basic factors affecting bond behavior, which is still of interest due to opposing opinions regarding its effect on bond behavior in the pull-out test. This paper presents an experimental and numerical bond analysis of ribbed reinforcing bar in concrete. The aim was to experimentally evaluate the effect of bar diameter on the bond behavior in the pull-out test and to perform numerical simulations of the...
-
Application of Rapid Prototyping technology in the manufacturing of turbine blade with small diameter holes
PublicationThe article presents the possibilities of using Rapid Prototyping (RP) technology in the manufacturing of turbine blades with small diameter holes. The object under investigation was gas turbine blade with small diameter cooling holes and holes for generating longitudinal vortices. A turbine blade model was produced by means of Direct Metal Laser Sintering (DMLS) technology and subsequently validated in terms of detection and accuracy...
-
The influence of height-to-diameter ratio on wind load of double-shell cylindrical, vertical tank
PublicationW pracy zaprezentowano badania modelowe obciążenia wiatrem dwupłaszczowych zbiorników walcowych o różnych smukłościach aerodynamicznych. Przedstawiono wyniki pomiarów przeprowadzonych na dwóch modelach zbiorników z dachem pływajacym i stosunku wysokości do średnicy płaszcza 0,45 i 0,25.
-
Pd nanoparticles with tunable diameter deposited on carbon nanotubes with enhanced hydrogen storage capacity
Publication -
Synthesis, Growth Mechanism, and Electrochemical Properties of Hollow Mesoporous Carbon Spheres with Controlled Diameter
Publication -
Experimental investigation of dryout of SES36, R134a, R123 and ethanol in vertical small diameter tubes
PublicationW publikacji przedstawiono wyniki badań eksperymentalnych kryzysu wrzenia typu dryout podczas wrzenia w przepływie czterech czynników (SES36, R134a, R123, alkohol etylowy) w kanałach o średnicy wewnętrznej 1.15 mm i 2.3 mm. Badania przeprowadzono w szerokim zakresie zmian stopnia suchości pary (0.65-1), gęstości strumienia masy (40-900 kg/(m2s)) i gęstości strumienia ciepła (20-220 kW/m2). W badaniach wykorzystano technikę termowizyjną...
-
The influence of height-do-diameter ratio on wind load of double-shell cylindrical, vertical tank
PublicationW pracy zaprezentowano skrót badań modelowych obciążenia wiatrem dwupłaszczowych zbiorników walcowych o różnych smukłościach aerodynamicznych. Przedstawiono wyniki pomiarów przeprowadzonych na dwóch modelach zbiorników z dachem pływającym i stosunku wysokości do średnicy płaszcza 0,45 i 0,25.
-
“DIY” Silica Nanoparticles: Exploring the Scope of a Simplified Synthetic Procedure and Absorbance-Based Diameter Measurements
Publication -
Zeta potential and effective diameter of n-tetradecane emulsions in n-propanol solutions and in the presence of lysozyme
Publication -
A new method for determination of flow boiling heat transfer coefficient in conventional diameter channels and minichannels
PublicationW pracy przedstawiono rozważania związane z modelowaniem wrzenia w przepływie w kanałach o średnicach konwencjonalnych, małych i minikanałach. Przedstawiono przegląd podejść do modelowania wymiany ciepła i w tym świetle przedstawiono oryginalne podejście autora. W przeciwieństwie do innych podejść metoda autora ma zastosowanie zarówno do kanałów o średnicach konwencjonalnych i minikanałach. Przedstawiono zadowalające porównania...
-
Experimental investigations on adiabatic frictional pressure drops of R134a during flow in 5mm diameter channel
PublicationThe article presents detailed two-phase adiabatic pressure drops data for refrigerant R134a at a saturation pressure of 5.5 bar corresponding to the saturation temperature of 19.4 °C. Study cases have been set for a mass flux varying from 100 to 500 kg/m2 s. The frictional pressure drop was characterized for the refrigerant R134a, for vapor qualities ranging from 0 to 1. Long-time thermal stability of test facility allowed to gather...
-
Calculation method for flow boiling and flow condensation of R134a and R1234yf in conventional and small diameter channels
PublicationThe paper presents the results of calculations performed using the authors’ model to predict the heat transfer coefficient during flow boiling for two refrigerants R134a and R1234yf. The experimental data from various past studies have been collected and the calculations have been conducted for the full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house...
-
Numerical Study of the Impinging Jets Formed by an Injector with Different Nozzle Diameters
PublicationThe collision of two or more liquid jets may provide considerable atomisation and efficient mixing of injected substances at the same time. This phenomenon is used, among others, in rocket engines, where the fuel and oxidiser are introduced separately and almost immediately mixed through self-impingement. Depending on the injection and operating conditions, diverse configurations of impinging jets are used, such as doublets,...
-
Markers of Anemia in Children with Type 1 Diabetes
Publication -
Bone status in adolescents with type 1 diabetes
Publication -
Benefits of hypertension management in diabetes: An opportunity not to be missed
Publication -
Cognitive Dysfunction in Type 1 Diabetes Mellitus
Publication -
Investigation of DPPC effect on SiO2 particles and in the presence of phospho(lipases) by zeta potential and effective diameter measurements
Publication -
Investigations of DPPC effect on Al2O3 particles in the presence of (phospho)lipases by the zeta potential and effective diameter measurements
Publication -
Striking influence of NiO catalyst diameter on the carbonization of polypropylene into carbon nanomaterials and their high performance in the adsorption of oils
Publication