Filters
total: 522
filtered: 314
-
Catalog
Chosen catalog filters
Search results for: PRZECINANIE ŚCIERNE
-
Dimensional accuracy and roughness of lamellas when sawing frozen wood
PublicationPrzedstawiono wpływ obniżania temperatury drewna sosnowego (-5°C i -20°C) i prędkości posuwu na dokładność wymiarową deszczułek oraz chropowatość powierzchni po przecinaniu. Badania prowadzono na pilarce ramowej wielopiłowej PRW15M z użyciem cienkich pił z ostrzami stellitowanymi. Otrzymywane wyniki odnoszono do wyników przecinania drewna o temperaturze +18°C. Profil grubości określano metodą kontaktową z pomiarem ciągłym na długości...
-
Modyfikacja powierzchni stopu Ti13Nb13Zr metodą implantacji jonowej w aspekcie zastosowania na elementy trące w endoprotezach ortopedycznych
PublicationW celu określenia wpływu wybranych czynników tribologicznych na intensywność zużycia ściernego pary trącej złożonej z nowoczesnego stopu tytanu Ti13Nb13Zr oraz PE-UHMW, przeprowadzono badania tribologiczne. Uzyskane wyniki badań wykazały zbyt niską odporność na zużycie ścierne stopu tytanu Ti13Nb13Zr. Stosunkowo niska trwałość badanego stopu tytanu, wskazuję na potrzebę modyfikacji jego powierzchni w celu zwiększenia twardości....
-
Badania tribologicznych właściwości nanokompozytowych warstw Ni-P/Si3N4 osadzanych metodą redukcji chemicznej na stopie aluminium AW-7075
PublicationPrzedstawiono wyniki tribologicznych badań warstw nanokompozytowych Ni-P/Si3N4 i niklowych Ni-P osadzonych na stopie aluminium AW-7075 metodą redukcji chemicznej, a także stopu AW-7075 bez powłoki. Warstwy nanokompozytowe wytworzono, stosując azotek krzemu Si3N4 w postaci polidyspersyjnego proszku o wielkości cząstek 20–25 nm. Analizowano wpływ zawartości w materiale warstwy fazy dyspersyjnej na twardość i zużycie ścierne, którą...
-
Creation and properties of the (Mn-N-O) layers on aluminium
Publicationprzedstawiono metodę wytwarzania warstw powierzchniowych zawierających mangan, azot i tlen na stopie Al-Si-Mg-Cu-Ni. Określono ich mikrostrukturę, mikrotwardość, wlaściwości tribologiczne oraz korozyjne w roztworze 0,01M H2SO4. Stwierdzono wielokrotny wzrost odporności na ścieranie stopu aluminium z wytworzoną warstwą wierzchnią we współpracy ciernej z żeliwem szarym perlitycznym.
-
The influence of the basic conditions of the forced feed of abrasive compound on the roughness of flat ceramic elements after lapping.
PublicationW docieraniu standardowym zawiesina ścierna dostarczana jest do strefy obróbki w sposób ciągły - zalewowo lub kroplowo, co generuje duże straty ścierniwa. W artykule opisano innowacyjny system dozowania i nanoszenia zawiesiny ściernej na powierzchnię żeliwnego docieraka tarczowego, który eliminuje tą wadę. W przeprowadzonych eksperymentach badano wpływ procentowej zawartości ziaren ściernych w nośniku oraz wielkość dawki zawiesiny...
-
On some approaches to cutting power estimation while wood sawing
PublicationW niniejszym artykule przedstawiono i porównano metody, które mogą być stosowane do szacowania mocy skrawania przy przecinaniu drewna na pilarkach tarczowych. Przy klasycznym podejściu efekty energetyczne procesu przecinania drewna piłami są obliczane na bazie właściwego powierzchniowego oporu skrawania. W internecie dostępne są narzędzia do określania mocy skrawania w postaci oprogramowania dostępnego on-line, przykładowo "Horsepower...
-
Recent progress in research on the cutting processes of wood. A review COST Action E35 2004-2008: Wood machining - micromechanics and fracture
PublicationZaprezentowano postępy w badaniach przecinania drewna ze szczególnym uwzględnieniem nowych metod dedykowanych zwiększeniu wydajności materiałowej w tartacznictwie. Zademonstrowano przydatność współczesnej mechaniki pękania do szacowania mocy skrawania dla pił, których wartości rozwarcia są różne od pił użytych w badaniach skrawalnościowych. W tych ostatnich wyznaczano wiązkość materiału obrabianego oraz naprężenia tnące. Badania...
-
Recent progress in research on the cutting processes of wood. A review COST Action E35 2004-2008: Wood machining - micromechanics and fracture
PublicationZaprezentowano postępy w badaniach przecinania drewna ze szczególnym uwzględnieniem nowych metod dedykowanych zwiększeniu wydajności materiałowej w tartacznictwie. Zademonstrowano przydatność współczesnej mechaniki pękania do szacowania mocy skrawania dla pił, których wartości rozwarcia są różne od pił użytych w badaniach skrawalnościowych. W tych ostatnich wyznaczano wiązkość materiału obrabianego oraz naprężenia tnące. Badania...
-
Methods of determining cutting forces during woodcutting
PublicationW artykule przedstawiono podstawowe metody określania sił przy przecinaniu drewna, które ulegały modyfikacjom wraz z postępem wynikającym z badań nad tym procesem. Przedstawione metody podzielono na dwie grupy: podejście klasyczne oraz nowatorskie podejście z zastosowaniem mechaniki pękania, które uwzględniają różne własności mające wpływ na proces przecinania. Podejście klasyczne reprezentują metody opierające się na właściwym...
-
Wybrane problemy szlifowania powierzchni płaskich z kinematyką docierania
PublicationW pracy przedstawiono teoretyczne i doświadczalne podstawy szlifowania powierzchni płaskich z kinematyką docierania. Dokonano kompleksowej analizy zastosowanych układów kinematycznych szlifierek. Przeprowadzono eksperymenty szlifowania jednostronnego ściernicami o spoiwie galwanicznym z ziarnami diamentowymi (D107, D64 i D46) oraz z regularnego azotku boru (B107 i B64). Innowacyjność ściernic polegała na zróżnicowanym utwierdzeniu...
-
ANALIZA EKONOMICZNA PRODUKCJI WARSTW LICOWYCH PODŁÓG KLEJONYCH WARSTWOWO
PublicationW artykule przedstawiono wyniki analiz wydajności liniowej, a także struktury kosztów produkcji, za pomocą cienkich pił na pilarce ramowej wielopiłowei i ta-śmowej, dębowych elementów licowych podłóg klejonych warstwowo. Stwierdzo-no, że przy przecinaniu deszczułek o grubości 4 mm o szerokości mniejszej od 180 mm bardziej wydajna jest pilarka ramowa wielopiłowa, zaś w pozostałych przypadkach widać przewagę wydajności pilarki taśmowej....
-
Technological effect comparison of abrasive and plastic working. Production Processes and Systems**2002 vol. 1 s. 89-98, 9 rys. 2 tabl. bibliogr. 6 poz Publication of the University of Miskolc. Porównanie technologicznych efektów obróbki ściernej i plastycznej.
PublicationPrzedstawiono wyniki badań porównawczych próbek obrobionych wykańczająco przez szlifowanie i docieranie oraz przez powierzchniową obróbkę plastyczną przez nagniatanie ślizgowe. Podano także konstrukcje narzędzi i przykłady stosowania badanych metod obróbki.
-
COMPARISON OF THE ABRASION RESISTANCE OF THE SELECTED BIOMATERIALS FOR FRICTION COMPONENTS IN ORTHOPEDIC ENDOPROSTHESES
PublicationRosnące z każdym rokiem zapotrzebowanie na endoprotezy stawów ortopedycznych przy jednoczesnym dążeniu do zwiększenia ich trwałości i wyeliminowania negatywnych skutków ubocznych produktów zużycia, które mogą wywoływać proces zapalny w tkankach determinuje potrzebę poszukiwania nowych biomateriałów, bądź metody modyfikacji ich powierzchni. Nadrzędnym celem prowadzonych przez nas badań było oszacowanie intensywności zużycia ściernego...
-
The effect of improved cutting conditions of the circular saw blade on precision of cutting
PublicationW pracy przedstawiono analizę i wyniki badań doświadczalnych dokładności przecinania na dwuwrzecionowej pilarce tarczowej. W warunkach przemysłowych badano piły starej (typ "Multix") i nowej konstrukcji podczas przecinania pryzm ze zmrożonego drewna brzozowego. Ponadto, określono wpływ kinematyki układu przecinania na uzyskiwaną dokładność przecinania.
-
Nowoczesne biostopy tytanu i kierunki ich rozwoju.
PublicationPrzedstawiono kierunki rozwoju biostopów tytanu zmierzające do wzrostu biokompatybilności, odporności na korozję, zmęczenie i zużycie ścierne. Zwrócono uwagę na szczególne znaczenie technik modyfikacji powierzchni.
-
Abrasive property evaluation during microgrinding with single-disk lapping kinematics
PublicationPrzedstawiono wyniki badań mikroszliwowania z kinematyką docierania jednotarczowego. Analizowano narzędzie pod kątem trwałości. Wyznaczono zmieniające się właściwości ścierne narzędzia z wykorzystaniem systemu do automatycznej analizy obrazu.
-
Hydrogen permeation through welded joints of S690QL steels at cathodic polarisation in sea water in the presence of SRB
PublicationPrezentowane są wyniki badan metodą Devanathana- Stachurskyego przenikania wodoru w wodzie morskiej w obecności bakterii redukujących siarczany i w warunkach sterylnych. Badania wykonano na stali S690QL poddanej symulowanym obróbkom cieplnym prowadzącym do struktur modelujących strefy wpływu ciepła. Stwierdzono dodatni wpływ obecności bakterii na przenikanie wodoru. Różnice między poszczególnymi próbkami były minimalne.
-
Tests for lapping of flat surfaces of ceramic elements with forced dosing of abrasive slurry
PublicationPrzedstawiono zagadnienia dotyczące systemu wymuszonego dawkowania zawiesiny ściernej w docieraniu jednotarczowym powierzchni płaskich. Opisano zalety takiego systemu dozowania płynnej zawiesiny ściernej. Omówiono wybrane wyniki badań docierania elementów z ceramiki technicznej. Analizowano wpływ podstawowych warunków dawkowania zawiesiny na ubytek liniowy próbek.
-
Modyfikacja powierzchni stopu Ti16Al4V przez nadtapianie laserowe w niskich temperaturach = Surface modification of the Ti6A14V alloy by laser melting in low temperature
PublicationPrzedstawiono założenia projektu badawczego zmierzającego do modyfikacji powierzchniowej stopu Ti6Al4V i uzyskaniu lepszej odporności na zużycie ścierne, tribokorozję i zmęczenie korozyjne dzięki nadtopieniu powierzchni stopu laserem w warunkach kriogenicznych.
-
Metody lutowania diamentów w narzędziach
PublicationLutowanie jest jedną z technik wytwarzania narzędzi zawierających kryształy, ziarna ścierne i polikrystaliczne spieki jako elementy robocze. W artykule omówiono różne sposoby lutowania diamentów oraz przedstawiono obszary ich zastosowania.
-
Productivity of wood cutting process
PublicationW artykule przedstawiono analizę przykładowej linii przecinania drewna. Produktywność linii oceniono na podstawie stopnia wykorzystania przecinarki i faktycznej prędkości przecinania.
-
Pro-ecological technology of wood sawing with circular saw blades
PublicationW niniejszym artykule opisano możliwości materiało- i energooszczędnego przecinania piłami tarczowymi. Przedstawiono również przykłady efektów zastosowania proekologicznych technologii przecinania w przemyśle.
-
Sawing frozen wood with narrow kerf saws: Energy and quality effects.
PublicationOpór skrawania zależy podczas przecinania nie tylko od wilgotności drewna lecz również od jego temperatury. W pracy przedstawiono wyniki badań eksperymentalnych przecinania drewna sosnowego zmrożonego na pilarce ramowej wielopiłowej. Dla porównania wykonano również testy dla drewna o temperaturze pokojowej. Czynnikami badanymi były: moc skrawania, dokładność przecinania w postaci grubości elementów, a także chropowatość powierzchni....
-
Creation and characteristics of the (Mn-N-O) surface layers on aluminium alloy
PublicationPrzedstawiono koncepcję tworzenia warstw powierzchniowych zawierających mangan, azot i tlen. Warstwy wykazują twardość powierzchniową 358 HV0,01, zwiększoną odporność na korozję w kwasie siarkowym oraz odporność na zużycie ścierne w skojarzeniu z żeliwem szarym.
-
The effect of thermal modification of ash wood on granularity and homogeneity of sawdust in the sawing process on a sash gang saw PRW 15-M in view of its technological usefulness
PublicationPrzedstawiono wyniki analiz granulometrycznych trocin, drewna jesionowego niemodyfikowanego (Fraxinus exelsior L.) i modyfikowanego termicznie, otrzymanych w procesie przecinania drewna na pilarce ramowej wielopiłowej PRW15-M. Przecinanie drewna prowadzono dla dwu prędkości posuwu 0,36 m·min-1 oraz 1,67 m·min-1. Ziarnistośćpowstających trocin dla drewna jesionowego modyfikowanego termicznie zawierała się w przedziale od 33,5 μm...
-
Laser assisted forming of the surface layer of Al-Si alloy at cryogenic conditions.
PublicationW artykule przedstawiono wpływ powierzchniowego laserowego przetapiania w warunkach kriogenicznych na mikrostrukturę, mikrotwardość i własności korozyjne stopu AlSi13Mg1CuNi. Stwierdzono korzystny wpływ obróbki laserowej na mikrostrukturę, mikrotwardość i odporność na zużycie ścierne badanego stopu aluminium.
-
Przemiany strukturalne warstwy wierzchniej stopu Al-Si za pomocą nadtapiania laserowego w niskiej temperaturze
PublicationPrzedstawiono technologię laserowego nadtapiania w warunkach kriogenicznych stopu Al-Si przy mocy wiązki lasera 1500-6000 W. Wykazano wzrost odporności na korozję i zużycie ścierne po nadtapianiu. Uzasadniono obserwowane efekty utworzeniem struktury nanokrystalicznej i amorficznej.
-
Laser surface treatment of aluminium alloys at cryogenic conditions.
PublicationPrzedstawiono nową metodę obróbki laserowej powierzchni stopów aluminium w warunkach kriogenicznych. W wyniku tej obróbki w warstwie wierzchniej stopów przeznaczonych na tłoki silników spalinowych uzyskano znaczące podwyższenie twardości, odporności na zużycie ścierne oraz wzrost właściwości korozyjnych.
-
Wpływ zawartości nanocząstek SiO2 na właściwości mechaniczne powłok kompozytowych na bazie żywicy fenolowej w kontekście ich zastosowania w przemyśle wydobywczym ropy i gazu
PublicationZagadnienie ochrony przed korozją jest szczególnie ważne w przemyśle wydobywczym, gdzie roczne koszty związane z korozją w samych Stanach Zjednoczonych przekraczają 1,4 miliarda USD. Dodatkowo niekontrolowana korozja powoduje niebezpieczne awarie prowadzące do skażenia środowiska, a także utraty zdrowia i życia ludzi. Największymi i najbardziej narażonym na korozję elementami pracującym w odwiercie są kolumny rur. Ze względu na...
-
Obróbka powierzchni płaskich narzędziami segmentowymi na docierarkach jednotarczowych.
PublicationPrzedstawiono wyniki badań jednotarczowego docierania powierzchni płaskich elementów żeliwnych. W badaniach stosowano niekonwencjonalne narzędzia ścierno-metalowe.
-
Diagnostic usefulness of granulometric analyses of chips distribution while sawing of wood
PublicationW niniejszym artykule opisano drogi transportu wiórów w procesie przecinania drewna i ich wpływ na rozdrobnienie wiórów. Przedstawiono również wyniki badań rozkładu segregacji wiórów powstających w procesie przecinania piłą o powszechnie stosowanej konstrukcji i piłą z domkniętymi rowkami wiórowymi.
-
Piły tarczowe o podwyższonej sztywności
PublicationPrzedstawiono zagadnienia transportu wiórów w procesie przecinania i zaprezentowano rozwiązanie konstrukcyjne piły, której rowki wiórowe ograniczają przedostawanie się wiórów pomiędzy korpus i ściany rzazu. Porównano sztywności statyczne i dynamiczne piły starego i nowego typu, a także zaprezentowano uzyskiwane efekty w postaci dokładności przecinania.
-
Analyses of the effect of the design features of the spindle of the sliding table saw upon its critical rotational speeds
PublicationProducenci pilarek formatowych do drewna dążą do zwiększania dokładności przecinania. Można to osiągnąć np. przez poprawę zachowania się wrzeciona, gdyż od niego w dużej mierze zależą efekty przecinania. Przedstawiono metodykę wyznaczania prędkości krytycznych wrzeciona pilarki formatowej w funkcji cech konstrukcyjnych wrzeciona i jego napędu.
-
Lekkie pokrycia z płyt warstwowych
PublicationDokonano przeglądu właściwości dostępnych na naszym rynku pływ warstwowych stosowanych na obudowy ścienne i dachowe w obiektach o konstrukcji stalowej
-
Mural i jego rola w przestrzeni zurbanizowanej
PublicationCzym tak naprawdę jest mural? Definicji jest bardzo wiele. Według Słownika języka polskiego PWN mural to „wielkie malowidło wykonane bezpośrednio na ścianie budynku”. Pierwotnymi malowidłami tego typu były prace naskalne z epoki paleolitu. Następnie ważnymi epokami dla rozwoju tego typu prac był starożytny Egipt i starożytny Rzym. Samo słowo „mural” pochodzi z języka hiszpańskiego (h. mural – ścienny; malarstwo ścienne). To dzięki...
-
Planläppen mit Schleif-Metall Läppscheibe von flachen Oberflächen.
PublicationPrzedstawiono wyniki badań docierania powierzchni płaskich narzędziami ścierno-metalowymi. Analizowano wpływ warunków obróbki na wydajność i jakość powierzchni elementów ceramicznych tlenkowych.
-
Analysis of abrasive powder at lapping
PublicationPrzedstawiono wyniki badań wpływu dawkowania pasty i zawiesiny ściernej na jakość docierania powierzchni płaskich. Analizowano parametry chropowatości powierzchni elementów ceramicznych i miedzianych.
-
Machining of the flat surfaces with abrasive-metallic lapping tools.
PublicationPrzedstawiono konstrukcje narzędzi ścierno-metalowych do obróbki powierzchni płaskich na docierarkach jednotarczowych. Przeprowadzono badania wydajności i jakości powierzchni elementów ceramicznych o małych gabarytach.
-
Tendencies in abrasive machining with lapping kinematics - experimental studies
PublicationW pracy przedstawiono tendencje rozwoju obróbki ściernej z wykorzystaniem kinematyki docierania. Zaprezentowano wyniki badań szlifowania specjalnymi narzędziami w układzie docierarki jedno- i dwutarczowej.
-
The fundamentals of narrow-kerf sawing; the mechanics and quality of cutting / K. A. Orłowski.
PublicationW pracy przedstawiono ekonomiczne i ekologiczne uwarunkowania dokładnego przecinania drewna za pomocą pił cienkich (o niewielkiej wartości rzazu). Opisano współczesne technologie wykorzystujące cienkie piły: pilarki tarczowe wielopiłowe, pilarki taśmowe i ramowe. W rozdziale drugim omówiono siły skrawania w ujęciu klasycznym, w którym do ich szacowania przyjmuje się przede wszystkim wartości właściwego powierzchniowego oporu skrawania,...
-
Lapping flat surfaces with forced dosing of abrasive suspension
PublicationPrzedstawiono zbudowane stanowisko do badań wymuszonego dawkowania zawiesiny ściernej w procesie jednostronnego docierania powierzchni płaskich. Podano przyjęty program badań oraz sposób opracowania wyników realizowanych eksperymentów.
-
Lapping flat surfaces with forced dosing of abrasive suspension
PublicationPrzedstawiono zbudowane stanowisko badawcze umożliwiające wymuszone dozowanie zawiesiny ściernej w operacji docierania jednotarczowego powierzchni płaskich. Podano program badań własnych oraz sposób opracowania otrzymanych wyników realizowanych eksperymentów.
-
The prediction method of the shear angle in the cutting zone during wood sawing
PublicationW artykule opisano metodę przewidywania kąta ścinania w strefie skrawania dla przypadku przecinania drewna. Kąt ścinania był określany z wykorzystaniem współczesnej mechaniki pękania. Nieliniowe równanie opisujące tą wielkość było rozwiązywane numerycznie za pomocą metody iteracyjnej Newton-Raphson. Otrzymane wyniki obliczeń wykazują możliwość rozszerzenia obszaru modelowania efektów energetycznych procesu przecinania drewna nawet...
-
Uniwersalne uchwyty obróbkowe wykorzystujące siły magnetyczne
PublicationPrzedstawiono współczesne konstrukcje uniwersalnych uchwytów przedmiotowych wykorzystujące do zamocowania przedmiotów obrabianych siły magnetyczne. Analizowano uchwyty magnetyczne i elektromagnetyczne w technologia obróbki wiórowej i ściernej oraz w technikach spawalniczych.
-
Machining by abrasive-metallic lapping tools.
PublicationPrzedstawiono kontrukcję niekonwencjonalnych narzędzi ścierno-metalowych do docierania. Opracowane narzędzia wykorzystano do badań wydajności i jakości docierania elementów ceramicznych. Określono wpływ podstawowych warunków docierania na efekty obróbki powierzchni płaskich.
-
Wood structure constraints on sawing accuracy with narrow-kerf saws
PublicationW pracy przedstawiono analizę przyczyn i przykłady niedokładności przecinania wynikających z lokalnych zmian struktury drewna.
-
Magnetyczne i elektromagnetyczne uchwyty obróbkowe - konstrukcja i rozwój
PublicationPrzedstawiono współczesne rozwiązania konstrukcyjne obróbkowych uchwytów magnetycznych i elektromagnetycznych. Podano przykłady zastosowania w operacjach obróbki wiórowej i ściernej oraz w różnorodnych procesach spawania. Omówiono ważniejsze zalecenia technologiczne oraz ograniczenia praktyczne.
-
Narzędzia dla docierarek jednotarczowych - modułowe konstrukcje i ich analiza.
PublicationPrzedstawiono konstrukcję ścierno-metalowych narzędzi o średnicy 380 mm do obróbki powierzchni płaskich. Omówiono szczegółowo ich modułową budowę i poddano analizie projektowej technologiczność konstrukcji. W ocenie stosowano kryteria konstrukcyjne i użytkowe
-
Axsial run-out circular saws
PublicationW pracy przedstawiono podstawowe przyczyny i efekty bicia osiowego ostrzy pił w układzie przecinania na pilarkach tarczowych.
-
Predictions of cutting power while sawing of birch and beech with the use of modern fracture mechanics
PublicationPraca zawiera wyniki badań eksperymentalnych procesu przecinania drewna brzozy i buka piłami o rzazie 2 mm na pilarce ramowej PRW15M. Na podstawie teoretycznego modelu Atkinsa, wyznaczono z danych eksperymentalnych stałe materiałowe (wiązkość i naprężenia tnące w strefie ścinania) i opracowano model do prognozowania mocy skrawania podczas przecinania drewna piłami na pilarce ramowej dla innych wartości rzazu w funkcji posuwu na...