Search
Search results for: WELDQN
-
Heat tint colours on stainless steel and welded joints
PublicationSurface layer condition of stainless steels and welded joints influences strongly their corrosion resistance. This problem seems to be underestimated. This current study explains the phenomenon of heat tint forming on welds, the methods of its removal, inspection procedures after heat tint removing and post weld finishing
-
COLD CRACKING OF S460N STEEL WELDED IN WATER ENVIRONMENT
PublicationThis paper shows results of weldability testing of fine-grained high -strength low- alloy S460N steel welded in water environment by covered electrodes. The tests were carried out by using the CTS test specimens with fillet welds. Four specimens were welded under water and one specimen in air. Welded joints were subjected to non-destructive visual and penetration tests. The accepted joints were then subjected to macroscopic and...
-
Design of thermal cutting table - welding technology and construction
PublicationW referacie przedstawiono pionierską pracę dyplomową stopnia inżynierskiego, wykonaną przez dwoje studentów Wydziału Mechanicznego Politechniki Gdańskiej zgodnie z systemem CDIO (Conceive, Design, Implement, Operate). W ramach pracy studenci zaprojektowali stół do cięcia termicznego metali (rysunki i obliczenia wytrzymałościowe metodą elementów skończonych), opracowali technologię spawania stołu oraz samodzielnie go wykonali. Stół...
-
Fatigue properties of laser welded steel sandwich panel.
PublicationPrzedstawiono wyniki badań laboratoryjnych paneli SANDWICH, prowadzonych w Kat. TOiOO Wydz. OiO na konstrukcjach w skali rzeczywistej. Przedstawiono program badań, omówiono założenia procedur badawczych i konstrukcję stanowisk testowych. Dokonano porównania uzyskanych rezultatów z wynikami prezentowanymi w literaturze. Przedstawiono propozycję algorytmu szacowania trwałości zmęczeniowej konstrukcji spawanych laserowo.
-
Mechanical properties of dissimilar welded joints for chemical tankers
PublicationArtykuł przedstawia właściwości mechaniczne złączy różnoimiennych stali typu duplex oraz austenitycznej typu 316L otrzymanych za pomocą spawania automatycznego łukiem krytym. Wykazano możliwość wykorzystania wysokowydajnej metody SAW w miejsce dotychczas stosowanych metod GTAW i GMAW do spawania blach zbiorników statków do przewozu chemikaliów. Pomimo obawy uzyskania nieodpowiednich struktur złączy okazało się, że spawanie stali...
-
Possibilities for assesment of the angular distortion in Welded T-joint
PublicationSpawanie jest podstawową techniką łączenia elementów konstrukcji kadłuba statku. Procesowi temu towarzyszą odkształcenia spawalnicze, co przysparza dużo problemów wykonawczych. W pracy przedstawiono wpływ przewymiarowania spoiny pachwinowej na wielkość kątowych odkształceń złącza. Dokonano porównania wartości określonych na podstawie inżynierskich hipotez z wynikami otrzymanymi podczas prób laboratoryjnych.
-
Investigations of welded joints of dissimilar heat resistant steels.
PublicationPrzeprowadzono badania metalograficzne połączeń spawanych różnorodnych stali żarowytrzymałych rur o przekroju 31,8x7,1 mm ze stali 10H2M z blachą ze stali 20H23N18. Badania makro- i mikrostruktury złączy spawanych wykazały, że istotnym czynnikiem wpływającym na właściwości mechaniczne złącza jest obecność wad takich jak pory lub wtrącenia żużla. Te nieciągłości w materiale powodują koncentrację naprężeń i powstawanie mikropęknięć.
-
APPLICATION POSSIBILITIES OF THE S960 STEEL IN UNDERWATER WELDED STRUCTURES
PublicationIn this paper, the application possibilities of the ultra-high strength (UHSS). Domex 960 steel in the underwater welded structures are analyzed. In the research, the investigated material has been tested in bead-on-plate wet welding conditions with the usage of different heat input values, namely 0.63 kJ/mm, 0.72 kJ/mm and 0.93 kJ/mm. Specimens were performed by the manual metal arc (MMA) welding method with the usage of rutile...
-
THE INFLUENCE OF MANUFACTURING OVERSIZING ON POSTWELDING DISTORTIONS OF THE FILLET WELDED JOINT
PublicationWelding proces is basic joining technique in shipbuilding. Such method generated welding distortions which cause a lot of problems during the manufacturing process. In the literature it is proposed wide spectrum of suggestions for a correct estimation of welding deformation in particular angular deformation in the fillet welded T joint. In the work influence of oversizing of weld on angular distortions of joint is presented basing...
-
Modelling of the Heat Flux Density Distribution for Laser Beam Welding
PublicationGreat interest of the laser beam welding in industry is a new theoretical task, making planning the welding procedure specification and the quality control of welded joints easier. Estimating and calculating the dimensions of a weld pool and temperature distribution near weld mainly concern heat source modelling. In the presented work calculations of welding pool shape and thermal field for cylindrical-powered-normally model of...
-
Designate CTOD of Weld Metal of butt weld, No WOiO/II/108/2013
PublicationTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
Artificial neural network based fatigue life assessment of friction stir welding AA2024-T351 aluminum alloy and multi-objective optimization of welding parameters
PublicationIn this paper, the fracture behavior and fatigue crack growth rate of the 2024-T351 aluminum alloy has been investigated. At first, the 2024-T351 aluminum alloys have been welded using friction stir welding procedure and the fracture toughness and fatigue crack growth rate of the CT specimens have been studied experimentally based on ASTM standards. After that, in order to predict fatigue crack growth rate and fracture toughness,...
-
Numerical Simulations of Laser and Hybrid S700MC T-Joint Welding
Publication -
Computational Techniques in Numerical Simulations of Arc and Laser Welding Processes
Publication -
APPLICATION OF NUMERICAL SIMULATIONS ON X10CRWMOVNB9-2 STEEL MULTILAYER WELDING
Publication -
Review of non- welded piping technologies on offshore equipment projects
PublicationThe aim of this article are considerations on welded and non-welded tube connection technologies, with advantages and disadvantages of both. After choosing non-welded solutions as the assembly method of choice, the thesis progresses to describing the most widely-used tube connection technologies (JIC, Ermeto, retain ring flanges, flared tube flanges and other, minor, solutions) and their properties.
-
Underwater wet welding of S1300 ultra-high strength steel
PublicationMarine Structures Volume 81, January 2022, 103120 Underwater wet welding of S1300 ultra-high strength steel Author links open overlay panelJacekTomkówGrzegorzRogalski https://doi.org/10.1016/j.marstruc.2021.103120 Get rights and content Under a Creative Commons licenseopen access Highlights • Technological method of S1300 steel underwater weldability improving was proposed. • Number of cracks and hardness of welded joints was...
-
Fatigue life tests of steel laser-welded sandwich structures
PublicationW publikacji zaprezentowano rezultaty systematycznych badań trwałości zmęczeniowej elementarnych połączeń wykonanych techniką spawania laserowego dla różnych wariantów geometrii złącz. Pokazano uzyskane wyniki i ich aproksymację, porównano uzyskane rezultaty dla różnych geometrii.
-
Tests of local strains in steel laser - welded sandwich structure
PublicationW publikacji zaprezentowano rezultaty badań odkształceń w strefie spoiny laserowej konstrukcji sandwich. Pokazano obiekt badań, metodykę i oprzyrządowanie oraz proces rejestracji. Przedstawiono uzyskane wyniki i wnioski z nich wypływające.
-
Corrosion resistance of dissimilar austenite and duplex steels welded joints
PublicationW artykule przedstawiono wpływ warunków spawania, a zwłaszcza energii liniowej, na odporność korozyjną złączy różnoimiennych stali austenitycznej 316L i typu duplex 2203. Przedstawiono wyniki testów korozyjnych:korozji wżerowej wg ASTM G48 oraz korozji naprężeniowej badanej w próbach odkształcania z małą pędkością w środowisku roztworu chlorku magnezowego.
-
Diffusible hydrogen content in deposited metal of multilayer welded joints
PublicationThe article describes manufacturing technology of multilayer joints in terms of control the diffusible hydrogen content. Diffusible hydrogen content in deposited metal for multilayer welded joints made of covered rutile electrodes or covered cellulosic and basic electrodes was determined. It was found that after four beads, the diffusible hydrogen content decreases in the case of the first technology from 36 ml/100 g to 18 ml/100...
-
Diffusible Hydrogen Control in Flux Cored Arc Welding Process
PublicationOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper an experimental...
-
The Effect of Welding Conditions on Diffusible Hydrogen Content in Deposited Metal
PublicationThe article presents the results of a literature survey and preliminary tests which set out effects of welding conditions on the amount of diffusible hydrogen in deposited metal. Experiments were conducted by using rutile coated electrodes which generate high contents of diffusible hydrogen in deposited metal. The amount of diffusible hydrogen was determined by a glycerin test.Eleven factors were considered: the electrode angle,...
-
Kinetics of Intermetallic Phase Precipitation in Manual Metal Arc Welded Duplex Stainless Steels
PublicationThe article presents the influence of heat treatment on the kinetics of transformations in lean duplex LDX2101 steel and a weld made of standard duplex 2209 material, which was welded by manual metal arc welding. Changes in the microstructure, hardness, and magnetic phase content were analyzed after heat treatment was conducted at a temperature of 800 °C for a period ranging from 15 to 1440 min. Light and scanning microscopy, Vickers...
-
Study on Microstructure and Mechanical Properties of Laser Welded Dissimilar Joint of P91 Steel and INCOLOY 800HT Nickel Alloy
PublicationThis investigation attempts to explore the weld characteristics of a laser welded dissimilar joint of ferritic/martensitic 9Cr-1Mo-V-Nb (P91) steel and Incoloy 800HT austenitic nickel alloy. This dissimilar joint is essential in power generating nuclear and thermal plants operating at 600–650 °C. In such critical operating conditions, it is essential for a dissimilar joint to preserve its characteristics and be free from any kind...
-
Study on Microstructural Characterization, Mechanical Properties and Residual Stress of GTAW Dissimilar Joints of P91 and P22 Steels
PublicationThis article deals with the dissimilar joining of two different grade Cr-Mo steel (2.25Cr-1Mo: P22 and modified 9Cr-1Mo: P91) for power plant application. The dissimilar butt-welded joint was produced for conventional V groove design by using the gas tungsten arc welding (GTAW) process with the application of an ERNiCrMo-3 Ni-based super alloy filler. A microstructure characterization was performed to measure the inhomogeneity...
-
Improvement of S355G10+N steel weldability in water environment by Temper Bead Welding
PublicationThe normalized S355G10 + N steel was chosen for testing, it is used in a variety of applications including the building of offshore structures, which may require repairs in water environment. The main aim of the work was to check susceptibility to cold cracking for fillet welds – Controlled Thermal Severity (CTS) tests and butt welds – Tekken tests and in the next step evaluation of effectiveness of Temper Bead Welding (TBW) application...
-
Modeling of Heat Source Based on Parameters of Electron Beam Welding Process
Publication -
Numerical Simulation of Electron Beam Welding Process of Inconel 706 Sheets
Publication -
Laser Dissimilar Welding of AISI 430F and AISI 304 Stainless Steels
PublicationA dissimilar autogenous laser welded joint of AISI 430F (X12CrMoS17) martensitic stainless steel and AISI 304 (X5CrNi18-10) austenitic stainless steel was manufactured. The welded joint was examined by non-destructive visual testing and destructive testing by macro- and microscopic examination and hardness measurements. With reference to the ISO 13919-1 standard the welded joint was characterized by C level, due to the gas pores...
-
Effect of electrode waterproof coating on quality of underwater wet welded joints
PublicationIn this paper, the effects of different hydrophobic coatings on the surface of covered electrodes on the quality of wet welded carbon steel joints were discussed. Commonly available hydrophobic substances used in industrial applications were selected for the research. The aim of using waterproof coatings was to check the possibility to decreasing the susceptibility of highstrength low-alloy S460N steel to cold cracking. During...
-
Underwater Wet Repair Welding of API 5L X65M Pipeline Steel
PublicationThis paper presents results of the research of effect of polymer insulation of pipeline made of API 5L X65M steel as well as underwater wet welding parameters on properties of joints made by covered electrodes. Effect of heat input on structure and hardness of joints during repair of underwater pipeline was analyzed. Welding defects like microcracks, micro-lacks of fusion, slag inclusions, as well as HAZ hardness increase over...
-
Study of the influence of thermal factors on the welding process of polyethylene gas pipelines,
PublicationA one-dimensional calculation scheme is proposed with the help of which it is possible to determine and set the technological parameters with the accuracy to be realized in production conditions: the temperature of the heating element and the heating time, which allows maximum mechanization of the technological operations of polyethylene gas pipelines welding. The numerical value of the coefficient of temperature for polyethylene...
-
Investigations into tendency to stress corrosion of joints welded in austenitic and duplex steels
PublicationPrzedstawiono wyniki badań spawanych złączy różnoimiennych wykonanych ze stali austenitycznej oraz typu duplex 2205. Badania podatności do korozji naprężeniowej złączy wykonano metodą odkształcania z małą prędkością. Próby przeprowadzono w środowisku obojętnym oraz agresywnym (MgCl2).
-
Stress corossion cracking susceptibility of dissimilar stainless steels welded joints
PublicationW artykule przedstawiono wyniki badań odporności na naprężeniowe pękanie korozyjne złączy różnoimiennych stali odpornych na korozję; austenitycznej 316L oraz typu duplex 2205. Badania próbek przeprowadzono techniką odkształcania z małą prędkością w agresywnym środowisku roztworu chlorku magnezowego. Wyniki badań korozyjnych uzupełniono analizą metalograficzną z obszarów przełomów.
-
Mechanical characteristics of welded joints between different stainless steels grades
Publicationnvestigation of mechanical characteristics of welded joints is one of the most important tasks that allow determining their functional properties. Due to the very high, still rising, cost of some stainless steels it is justified, on economic grounds, welding austenitic stainless steel with steels that are corrosion-resistant like duplex ones. According to forecasts the price of...
-
Determining diffusible hydrogen amounts using the mercury method. Welding International
PublicationW artykule przedstawiono szczegółową charakterystykę procedury oznaczania ilości wodoru dyfundującego metodą rtęciową na tle innych metod badawczych i aktualnego stanu wiedzy dotyczącego rozpatrywanego zagadnienia. Omówiono klasyfikację wodoru występującego w złączu spawanym oraz metody oznaczania ilości wodoru dyfundującego w stopiwie ze zwróceniem szczególnej uwagi na metodę rtęciową jako metodę podstawową. Zestawiono zależności...
-
Hydrogen effects in duplex stainless steel welded joints - electrochemical studies
PublicationIn this work results on the influence of hydrogen on passivity and corrosion resistance of 2205 duplex stainless steel (DSS) welded joints are described. The results were discussed by taking into account three different areas on the welded joint: weld metal (WM), heat-affected zone (HAZ) and parent metal. The corrosion resistance was qualified with the polarization curves registered in a synthetic sea water. The conclusion is that,...
-
Evolution of post welded residual stress due multilayer circumferentialweld of tube.
PublicationOpisano sposób wykorzystania polowego efektu Barkhausena do pomiaru rozkładu naprężeń w spawanych rurach. Przedstawiono procedurę kalibracji oraz wyniki pomiaru naprężeń uzyskanych po stopniowym spawaniu rury.
-
Research on deformations of laser-welded joint of a steel sandwich structure model.
PublicationPrzedstawiono problemy związane z zachowaniem złącza laserowego pod obciążeniem zginającym. Pokazano wyniki badań laboratoryjnych dla określenia mechanizmu pracy złącza i przedyskutowano uzyskane rezultaty.
-
The influence of the welding thermal cycles on corrosion resistance of duplex stainless steel
PublicationBadano skłonnośc strefy wpływu ciepła spoin ze stali dupleks do korozyjnego pękania narężeniowego. Wykonano próby korozyjne z wykorzystaniem metody SSRT w środowisku korozyjnym wrzącego MgCl2. Wykazano, że duży udział ferrytu w strukturze SWC pogarsza odpornośc na korozję. Badania metalograficzne na mikroskopie lektronowym wykazały różne sposoby propagacji pęknięcia zależnie od zawartości austenitu w strukturze SWC.
-
Investigations of dissimilar stainless steels welded joints for chemical tankers construction
PublicationArtykuł przedstawia właściwości mechaniczne złączy różnoimiennych stali typu duplex oraz austenitycznej typu 316L otrzymanych za pomocą spawania automatycznego łukiem krytym. Wykazano możliwość wykorzystania wysokowydajnej metody SAW w miejsce dotychczas stosowanych metod GTAW i GMAW do spawania blach zbiorników statków do przewozu chemikaliów.
-
Influence of annealing on joint zone of explosive welded and rolled Al-Cuplate
PublicationRosnące wciąż wymagania co do metalowych materiałów jednorodnych przyczyniło się do zwiększenia zainteresowania materiałami platerowanymi. Blachy platerowane często znajdują zastosowanie w przemyśle chemicznym i petrochemicznym jako materiały antykorozyjne odporne na działanie agresywnego środowiska, w przemyśle okrętowym jako łączniki stopów aluminium ze stalą, w budowie zgrzewarek jako połączenia szczęk z blachą stalową, w przemyśle...
-
Exploring the trends in flux-cored arc welding: scientometric analysis approach
PublicationFlux-cored arc welding (FCAW) is a universal group of welding methods in terms of the scope of application and automation possibilities, the share of which in various industries in many countries is still increasing. The paper presents the results of bibliographic analyses (scientometric analysis with the use of VOSviewer, Bibliometrix and CitNetExplorer tools) of a data set of 993 publications indexed in the Web of Science database...
-
Mechanism of hydrogen enhanced-cracking of high-strength steel welded joints
PublicationPrzedstawiono badania podatności stali spawalnej o wysokiej wytrzymałości S690Q i jej złączy spawanych na niszczenie wodorowe w środowisku wody morskiej przy polaryzacji katodowej. Na podstawie wyników próby rozciągania z małą prędkością odkształcania i obserwacji przełomów próbek na SEM wskazano mechanizm pękania wspomaganego wodorem badanej stali i złączy spawanych.
-
Microstructure and Mechanical Properties of Combined GTAW and SMAW Dissimilar Welded Joints between Inconel 718 and 304L Austenitic Stainless Steel
PublicationA dissimilar welded joint of Inconel 718 and 304L austenitic stainless steel was prepared using a combined procedure with the gas tungsten arc welding and shielded metal arc welding processes by employing the Ni-based fillers: ERNiCr-3 and ENiCrFe-3. The welded joints were investigated for metallographic testing and mechanical properties, and a relationship was established between the microstructure and the resultant mechanical...
-
Weldability of S500MC Steel in Underwater Conditions
PublicationWet welding with the use of covered electrodes is one of the methods of underwater welding. This method is the oldest, the most economic and the most versatile. The main difficulties during underwater wet welding are: high cooling rates of the joint, the presence of hydrogen in the arc area and formation of hard martensitic structure in the weld. These phenomena are often accompanied by porosity of welds and large number of spatters,...
-
Designate of CTOD for WM and HAZ, report no: WOiO/II/122/2014
PublicationTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
Designate CTOD Heat Affected Zone of butt weld, Report No: WOiO/II/76/2013
PublicationTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
CTOD designation for WM and HAZ in butt joint made from S460 ML steel, Expertise No. WOiO/II/82/2015
PublicationTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...