Search
Filters
total: 2597
displaying 1000 best results Help
Search results for: WELDING METALLURGY
-
Problems of Determination of Welding Angular Distortions of T-fillet Joints in Ship Hull Structures
PublicationShip hull structure elements are in majority joined by welding. Welding distortions can cause a lot of problems during the manufacturing process. In the literature it is proposed wide spectrum of suggestions for a correct estimation of welding deformation in particular angular deformation in the fillet welded T joint. In the work verification of selected methods is proposed basing upon of the results of the laboratory measurements....
-
Effect of shielded electrode wet welding conditions on diffusible hydrogen content in deposited metal
PublicationWet welding is the most popular method of joining in water enviroment. During underwater welding, the weldability of steel is limited by the higher cooling rates and hydrogen content in weld metal. Article presents results of preliminary tests on the effects of wet welding conditions on diffusible hydrogen amount. Seven parameters were optimized using a Plackett-Burman plan to get the most relevant variables. These parameters were:...
-
INFLUENCE OF TACK WELDS DISTRIBUTION AND WELDING SEQUENCE ON THE ANGULAR DISTORTION OF TIG WELDED JOINT
PublicationIn this paper the influence of tack welds distribution and welding sequence on angular distortion of the Tungsten Inert Gas (TIG) welded joint was tested. Additionally, the effect of welding current on angular distortion was assessed. For research X2CrTiNb18 (AISI 441) stainless steel (2.5 mm thick) was chosen. During research specimens were prepared with different distributionsof tack...
-
Autogenous Fiber Laser Welding of 316L Austenitic and 2304 Lean Duplex Stainless Steels
PublicationThis study presents results of experimental tests on quality of dissimilar welded joints between 316L austenitic and 2304 lean duplex stainless steels, welded without ceramic backing. Fiber laser welded butt joints at a thickness of 8 mm were subjected to non‐destructive testing (visual and penetrant), destructive testing (static tensile test, bending test, and microhardness measurements) and structure observations (macro‐ and...
-
Effect of the welding environment and storage time of electrodes on the diffusible hydrogen content in deposited metal
PublicationIn the study the glycerin displacement method was used for determination of diffusible hydrogen content in deposited metal. Specimens were welded in the air and in the water with covered rutile electrodes. The first part of the specimens was made immediately after opening the package of the electrodes. The electrodes were then stored in opened packages in laboratory conditions that allowed for contact with the air for three years....
-
The influence of the welding environment on the properties of Tekken joints made from S355J2C+N steel
PublicationThere are three main methods of underwater welding: dry, wet and intermediate between them, by using the local dry chamber. Due to low costs, the most common method is the wet welding with the use of covered electrodes. Water as a welding environment carries out a lot of problems. The first is limited visibility and instability of the welding arc. The biggest problem during underwater welding is high susceptibility to cold cracking,...
-
Diffusible hydrogen management in underwater wet self-shielded flux cored arc welding
PublicationThis article reports the effect of underwater wet welding parameters and conditions on the diffusible hydrogen content in deposited metal for welding with a self-shielded flux cored wire. The diffusible hydrogen content in deposited metal was determined using the glycerin method according to the Plackett-Burman design determining the significance of the effect of the stick out length, welding current, arc voltage, travel speed...
-
Application of the Mathar method to identify internal stress variation in steel as a welding process result
PublicationThe paper deals with the method to identify internal stresses in two-dimensional steel members. Steel members were investigated in the delivery stage and after assembly, by means of electric-arc welding. In order to perform the member assessment two methods to identify the stress variation were applied. The first is a non-destructive measurement method employing local external magnetic field and to detecting the induced voltage,...
-
Effects of nordic pole walking on oxidative stress and walking abilities in patients with intermittent claudication
Publication -
Metallurgical Transactions B (Process Metallurgy)
Journals -
Mineral Processing and Extractive Metallurgy Review
Journals -
Piotr Jamroz dr hab. inż.
PeoplePiotr Jamroz graduated from Wroclaw University of Technology, Faculty of Chemistry in 1998 and obtained his PhD from the same university in 2003. Currently he works as an associate professor at Wroclaw University of Science and Technology, Faculty of Chemistry, Division of Analytical Chemistry and Chemical Metallurgy. His research interests are related to generation and diagnostics of different kinds of plasma sources, including...
-
Code Obfuscation. Where is it Heading?
Publication -
The Challenge of Quantification: An Interdisciplinary Reading
PublicationThe present work looks at what we call “the multiverse of quantification”, where visible and invisible numbers permeate all aspects and venues of life. We review the contributions of different authors who focus on the roles of quantification in society, with the aim of capturing different and sometimes separate voices. Several scholars, including economists, jurists, philosophers, sociologists, communication and data scientists,...
-
Wetting of surfaces with ionic liquids
PublicationW pracy skupiono się na ocenie zwilżalności wybranych powierzchni stałych cieczami jonowymi. Jako związki testowe zastosowano chlorki dialkiloimidazoliowe. Porównano kąty zwilżania wybranych cieczy jonowych stosując metodę wzniesienia kapilarnego oraz metodę siedzącej kropli. Podczas testu zaobserwowano obniżanie wartości współczynnika lepkości cieczy jonowych wynikającą z ekspozycji płynu na parę wodną zawartą w powietrzu atmosferycznym....
-
An investigation on wetting of porous materials
PublicationPośrednie metody oceny zdolności zwilŜania drobnych cząstek lub materiałów porowatych wymagają wyboru cieczy odniesienia, dla której kąt zwilŜania jest równy zeru. W badaniach własnych zastosowanometodę wzniesienia kapilarnego oraz metodę flotacji filmowej dla układów mikrokulki szklane-woda i mikrokulki szklane-dekan. Uzyskane dane dla cieczy odniesienia i dla cieczy badanej wprowadzano dozmodyfikowanego równania Washburn'a i...
-
Hanjie Xuebao/Transactions of the China Welding Institution
Journals -
Analysis of Residual Stresses and Dislocation Density of AA6082 Butt Welds Produced by Friction Sir Welding
PublicationThe Friction Stir Welding (FSW) method was employed to join AA6082 sheets. The welds were produced with different tool traverse speed (200 and 250 mm/min), rotational speed (1000 and 1250 RPM) and tool tilt angle (0 and 2 deg). Based on the analysis of XRD patterns, the total precipitation volume fractions in the nugget zones and the base material were calculated. The FSW process resulted in a reduction in the fraction of precipitates...
-
A Study on Deformation According to Steel Constraints During Thick-Plate Fillet Welding and Line Heating
Publication -
Review the Ultimate Strength According to Welding Deformation Criteria of Thin Plates Under In-plane Compression
Publication -
Effect of underwater local cavity welding method conditions on diffusible hydrogen content in deposited metal
PublicationOne of the methods with great potential for applications in underwater repairs is local cavity welding. In local cavity method, cooling conditions and diffusible hydrogen amount in weld metal are nearly the same as those existed during welding in the air. This paper presents the results of literature survey and preliminary tests of the effect of local cavity welding conditions on diffusible hydrogen amount in a deposited metal....
-
Reading & Writing-Journal of the Reading Association of South Africa
Journals -
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
Journals -
Reading Medieval Studies
Journals -
Reading & Writing Quarterly
Journals -
Reading Research and Instruction
Journals -
Reading in a Foreign Language
Journals -
Journal of Research in Reading
Journals -
Reading Research Quarterly
Journals -
Scientific Studies of Reading
Journals -
Effect of body composition on walking economy
Publication -
Load function walking pedestrian on the footbridge.
PublicationModern foot bridges are more and more sensitive to variable load created by moving pedestrians. These are several reasons for that. Quickly growing up road infrastructure forces us to build foot bridges just to reconnect one piece of land, separated now by the new road or railway. These bridges are lightweight because the only live load acting on them comes from pedestrians.The paper focuses on the definition of human induces dynamic...
-
Temperature-Based Prediction of Joint Hardness in TIG Welding of Inconel 600, 625 and 718 Nickel Superalloys
Publication -
Journal of the Southern African Institute of Mining and Metallurgy
Journals -
Mining Technology-Transactions of the Institutions of Mining and Metallurgy
Journals -
Fenmo Yejin Jishu/Powder Metallurgy Technology
Journals -
JOURNAL OF THE SOUTH AFRICAN INSTITUTE OF MINING AND METALLURGY
Journals -
Pin Angle Thermal Effects on Friction Stir Welding of AA5058 Aluminum Alloy: CFD Simulation and Experimental Validation
PublicationThe friction stir welding (FSW) of tool pin geometry plays a critical role in the final properties of the produced joint. The tool pin geometry directly affects the generation of heat and the flow of internal materials during the FSW process. The effects of the FSW tool pin angle on heat generation and internal flow have not been quantitatively investigated in detail. In this manuscript, a validated Computational Fluid Dynamic...
-
Mechanical and structural behavior of high-strength low-alloy steel pad welded by underwater wet welding conditions
PublicationThe aim of the paper was to determine the metallurgical and mechanical behaviors of a high-strength low-alloy (HSLA) steel pad-welded specimen used in the structures of industrial and naval parts. Then to predict the metallurgical consequences (nature of the phases present) and the mechanical properties (hardness and impact strength) of the pad-welded steel obtained by underwater wet welding with different heat input values. The...
-
Direct measurements and numerical predictions of welding-induced initial deformations in a full-scale steel stiffened plate structure
Publication -
A Study on Welding-induced Temperature Distribution and Deformation of IMO Type C LNG Fuel Tank Support Structures
Publication -
Induction Assisted Hybrid Friction Stir Welding of Dissimilar Materials AA5052 Aluminium Alloy and X12Cr13 Stainless Steel
PublicationThis research aimed to study the induction in-situ heated hybrid friction stir welding (IAFSW) method to join AA5052 aluminium alloy with X12Cr13 stainless steel (SS) to enhance joint strength. The potency of this method on the mechanical properties and microstructural characterizations were also investigated. The results show that the transverse tensile strength gained was 94% of the AA5052 base metal that is 229.5 MPa. This superior...
-
The influence of welding heat input on the quality and properties of high strength low-alloy dissimilar steel butt joints
PublicationThe paper presents the results of non-destructive and destructive tests of dissimilar highstrength low-alloy S460ML and S460N steel butt joints. These steels are characterized by similar mechanical properties, but their carbon equivalent CeIIW values are much different. The joints were made using different values of heat input for each welding bead. They were tested by non-destructive methods: visual, penetrant, radiographic and...
-
On the Application of Magnetoacoustic Emission for a Nondestructive Assessment of the Post Welding Heat Treatment of High Chromium Steel Weld Seams
PublicationThe paper analyses the possibility of post weld heat treatment (PWHT) quality assessment with the help of magnetoacoustic emission (MAE) signal measurements. Two welded superheater tubes, made of high chromium VM12 steel, were analysed—as welded and heat treated one. The analysed sample in the as welded state exhibited significantly higher hardness, accompanied by a big difference in the MAE signal intensity (of order of about...
-
Keikinzoku Yosetsu/Journal of Light Metal Welding and Construction
Journals -
Yosetsu Gakkai Shi/Journal of the Japan Welding Society
Journals -
Angular welding distortion - one sided fillet weld
Open Research DataWelding is the basic method of joining ship hull elements during its construction. However, this method of joining structural elements generates shrinks. Shrinks causes deformation of the entire welded structure, both linear and angular. In the shipbuilding industry, there is a tendency to oversize fillet welds, at the design as well as manufacturing...
-
Swelling effects in cross-linked polymers by thermogravimetry
Publication -
On the Bending of Multilayered Plates Considering Surface Viscoelasticity
PublicationWe discuss the bending resistance of multilayered plates taking into account surface/interfacial viscoelasticity. Within the linear surface viscoelasticity we introduce the surface/interfacial stresses linearly dependent on the history of surface strains. In order to underline the surface viscoelasticity contribution to the bending response we restrict ourselves to the elastic behaviour in the bulk. Using the correspondence principle...
-
Totally laparoscopic feeding jejunostomy – a technique modification
Publication