Search
Institute of Energy
Publications
Filters
total: 1026
displaying 1000 best results Help
Catalog Publications
Year 2016
-
The dying medium temperature impact on the final moisture content of pine wood at constant drying time
PublicationThe results of final moisture content of pine wood (Pinus sylvestris L.) after drying process are presented. The wood in the experiments was taken from the northern part of Pomeranian region in Poland. The drying process was performed in the experimental chamber equipped with the micro-jet heat exchanger. The air at temperatures of 40°C, 60°C, 80°C, 100°C and 120°C with relative humidity about 60% and atmospheric pressure was the...
-
The low temperature waste heat recovery in drying process of pine wood using micro-jet heat exchanger
PublicationThe article presents the influence of the drying medium temperature changes for the relative and absolute moisture content values during pine wood drying. The drying process was conducted at constant atmospheric pressure and with different drying medium (air) temperature levels, respectively: 40oC, 60oC, 80oC, 100oC, and 120oC. In order to develop a method that would enable low temperature drying of solid materials the experiments...
Year 2020
-
THE EFFECT OF DRYING INTENSITY ON THE COLOR CHANGES OF PINE WOOD (PINUS SYLVESTRIS L.)
PublicationThe effect of the selection of drying process parameters on the color change of Scots pine wood (Pinus Sylvestris L.) is presented. In this work the experimental studies have been performed. The research focused on the influence of drying intensity on the changes of color after drying process. Intensity of drying process was determined on the basis of the average drying gradient. To determine the color of wood before and after...
Year 2018
-
The Effect of Full-Cell Impregnation of Pine Wood (Pinus sylvestris L.) on Changes in Electrical Resistance and on the Accuracy of Moisture Content Measurement Using Resistance Meters
PublicationThe impact of the full-cell impregnation of pine wood was investigated with respect to changes in electrical resistance and the accuracy of moisture content measurement. This study compared the resistance of impregnated and untreated pine timber harvested from the northern part of Poland (Pomeranian region). The wood was impregnated by the vacuum-pressure method. The preservative (TANALITH E 3475) and coloring (TANATONE 3950) agents...
-
The effect of reduced pressure on carbon dioxide flow boiling heat transfer in minichannels
Publication. In the paper presented are the results of the study on the effect of reduced pressure on flow boiling heat transfer data in minichannels as well as conventional ones. That effect renders that most of heat transfer correlations fail to return appropriate results of predictions. Mostly they have been developed for the reduced pressures from the range 0.1-0.3. The special correction has been postulated to the in-house model of flow...
-
The Experimental Determination of Bearings Dynamic Coefficients in a Wide Range of Rotational Speeds, Taking into Account the Resonance and Hydrodynamic Instability
PublicationMethods for the experimental determination of dynamic coefficients are commonly used for the analysis of various types of bearings, including hydrodynamic, aerodynamic and foil bearings. There are currently several algorithms that allow estimating bearing dynamic coefficients. Such algorithms usually use various excitation techniques applied to rotor–bearings systems. So far only a small number of scientific publications show how...
-
The influence of microjet array area ratio on heat transfer in the compact heat exchanger
PublicationThe paper describes the comprehensive study on the effect of microjet array geometrical parameters on the heat transfer enhancement in the modular heat exchanger. The conducted experimental study provides an experimental database on single phase submerged microjet heat transfer. The Wilson plot method was applied to determine the heat transfer coefficients in the laminar and transition flow regimes of a liquid-to-liquid heat exchanger....
-
The use of liquid crystal thermography TLC and particle image velocimetry PIV in selected technical applications
PublicationNowadays, the energy cost is very high and this problem is carried out to seek techniques for improvement of the aerothermal and thermal (heat flow) systems performances in different technical applications. The transient and steady-state techniques with liquid crystals for the surface temperature and heat transfer coefficient or Nusselt number distribution measurements have been developed. The flow pattern produced by transverse...
-
Thermal and hydraulic phenomena in boundary layer of minijets impingement on curved surfaces
PublicationPresented work considers flow and thermal phenomena occurring during the single minijet impingement on curved surfaces, heated with a constant heat flux, as well as the array of minijets. Numerical analyses, based on the mass, momentum and energy conservation laws, were conducted, regarding single phase and two-phase simulations. Focus was placed on the proper model construction, in which turbulence and boundary layer modeling...
Year 2011
-
The effect of pressure on heat transfer during pool boiling of water-Al2O3 and water-Cu nanofluids on stainless steel smooth tube
PublicationPrzedstawiono wyniki badań eksperymentalnych wrzenia nanocieczy woda-Al2O3 i woda-Cu o koncentracjach nanocząstek 0.01%, 0.1% oraz 1% przy ciśnieniu absolutnym 10 kPa, 100 kPa oraz 200k Pa.
-
The effect of pressure on heat transfer during pool boiling of water-Al2O3 and water-Cu nanofluids on stainless steel smooth tubes
PublicationPrzedstawiono wyniki badań eksperymentalnych wrzenia nanocieczy woda-Al2O3 i woda-Cu o koncentracjach nanocząstek 0.01%, 0.1% oraz 1% przy ciśnieniu absolutnym 10 kPa, 100 kPa oraz 200k Pa.
-
The Method of Reduction of Aerodynamic Forces Generated in Turbine Blade Seals
PublicationOpisano metodę zmniejszania sił wymuszających drgania aerodynamiczne poprzez zastosowanie nowego uszczelnienia nadbandażowego typu komorowego. Efektywność stosowania uszczelnienia komorowego potwierdzono obliczeniami numerycznymi i badaniami eksperymentalnymi.
-
The new concept of capillary forces driven evaporator with application to waste heat recovery
PublicationW pracy omówiono koncepcję zastosowania rurki ciepła w nowoczesnej konstrukcji parownika wspomagającego za pomocą sił kapilarnych pompę obiegu termodynamicznego czynnika. Rozwiązanie takie może znaleźć zastosowanie w domowej mikrosiłowni CHP
Year 2019
-
THE EFFECT OF WOOD DRYING METHOD ON THE GRANULARITY OF SAWDUST OBTAINED DURING THE SAWING PROCESS USING THE FRAME SAWING MACHINE
PublicationThe experimental results of the study focused on the effect of drying processes of warm air drying at the temperature of 6580°C and warm air-steam mixture drying at the temperature of 105°C of pine and beech wood to the size of sawdust grains created by cutting using RPW 15M frame saw is presented in the paper. Particle size analysis of dry sawdust was performed using two methods - screening method and optical method based on...
-
The impact of drying and steaming processes on surface color changes of tension ad normal beech wood
PublicationThe aim of the article is to present the influence of high temperature to selected properties of beech wood (Fagus sylvatica L.). The properties such as moisture content, color changes and longitudinal warping were analyzed. The quality of beech wood is determined based on structure and properties of wood, frequency of defects in wood material. The tension wood is considered as an important wood defect causing negative alterations...
-
The impact of environmentally friendly refrigerants on heat pump efficiency
PublicationThis paper discusses the issue of heat pump simulation. Lower operating costs can be achieved through good equipment design and appropriate operation. Detailed technical and economic analysis inform the selection of system components with the highest possible efficiency and lower energy demand. The use of systems based on environmentally friendly refrigerants can deliver long product life, which is associated with a shorter payback...
-
The thermal effort during marine steam turbine flooding with water
PublicationThe work discussed an extreme case of cooling a steam turbine. The ship's steam turbine was used as an example. In marine transport units with low-speed engines dominate, however, there are also units with steam turbines. An example of analysed marine steam turbine is shown in Fig. 1. When considering the issue of cooling steam turbines, it is necessary to estimate the extreme conditions that may occur during operation of the turbine....
-
Thermal and economic investigation of straight and U-bend double tube heat exchanger with coiled wire turbulator
PublicationExperimental research has been carried out for four individual heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend and U-bend with turbulator. Tests were made for the water-water system. The study covered a wide measuring range, i.e., Re = 800–9000 – on the shell side, for a constant cold water temperature of 9 ◦C and hot water of 50 ◦C. The heat exchangers were made from copper tubes with...
Year 2014
-
The Effect of Wood Provenance and Density on Cutting Forces While Sawing Scots Pine (Pinus sylvestris L.)
PublicationSeveral properties of wood including the cutting power requirements can be correlated to wood density. Therefore, according to the literature, the cutting power requirements (and/or cutting forces) could be computed as a function of the wood specific gravity. This research shows that such an approach, based solely on specific gravity, may be considered a rather rough and imperfect estimate of cutting power. Samples of Scots pine...
-
The influence of drying parameters on wood properties
PublicationResults of influence of gas-steam mixture drying process on wood mechanical properties are presented. Wood species, namely pine (Pinus sylvestris L.) and beech (Fagus silvatica L.) from the northern part of Pomerania region in Poland, were subject of steam kiln-drying process in a laboratory kiln specially arranged for that reason.
-
The influence of drying parameters on wood properties
PublicationThe influence of drying conditions on wood properties is presented. The classical approach was used to determine energetic effects (cutting forces and cutting power) of wood sawing process on the basis of the wood specific cutting resistance, material constant. Before mashining wood material (soft and hard) was dryied at various conditions using air at 25oC, air-steam meaxture at 80oC and steam at 110oC.
-
The initial selection of parameters for dynamic brake for car engine test dynamometer
PublicationThe article presents an analysis of the car engine loads. The aim of the analysis was to determine the parameters of the brake / electric motor on an engine test bad. Analysis of loads on the driving tests concerned on chassis dynamo to simulate them on an engine dynamometer. To check the range of dynamometer shaft angular acceleration inertial mass of a car was reduced on the crankshaft axis. The calculations of maximum shaft...
-
The Use of Liquid Crystal Thermography in Selected Technical and Medical Applications—Recent Development
PublicationThermochromic liquid crystals (TLC) and true-colour digital image processing have been successfully used in non-intrusive technical, industrial and biomedical studies and applications. Thin coatings of TLC at surfaces are utilized to obtain detailed temperature distributions and heat transfer rates for steady or transient processes. Liquid crystals also can be used to make the temperature and velocity fields in liquids visible...
-
THERMAL ANALYSIS AND DESIGN OF HYBRID MICROCHANNEL -MICROJET TEST PROBE
PublicationAccurate control of cooling parameters is required in ever wider range of technical applications. It is known that reducing the flow hydraulic diameter to an increase in the economy of cooling and improves its quality (Mikielewicz and Muszyński 2009). Present study describes research results related to the design and construction of the test stand for hybrid microjet- microchannel cooling modules study, which may be applied in...
-
THERMAL ANALYSIS AND DESIGN OF HYBRID MICROCHANNEL-MICROJET TEST PROBE
PublicationThe paper presents the numerical investigation of a microjet- microchannel cooling module. In which microjets of water are impinging into the microchannels and forming a liquid film on the impingement surface. Applied technology takes benefits from two very attractive heat removal techniques. When lminar jets are impinging on the surface have a very high kinetic energy at the stagnation point, also in microchannels boundary layer...
-
Thermal Analysis Of Hybrid Microchannel-Microjet Heat Exchanger
PublicationThe paper presents the numerical investigation of a microjet- microchannel cooling module. In which microjets of water are impinging into the microchannels and forming a liquid film on the impingement surface. Applied technology takes benefits from two very attractive heat removal techniques. When laminar jets are impinging on the surface have a very high kinetic energy at the stagnation point, also in microchannels boundary layer...
Year 2017
-
The effectivness of fault detection in common rail injectors examination methods
PublicationThe article presents the effectiveness tests of fault detection in common rail injectors. 40 injectors with different wear levels were tested. Testing was made on two test benches of a completely different design. Research includes comparison of accuracy, reproducibility and testability to detect specific defects. A device was created for visualization of the fuel injector spraying steam.
-
The experimental identification of the dynamic coefficients of two hydrodynamic journal bearings operating at constant rotational speed and under nonlinear conditions.
PublicationHydrodynamic bearings are commonly used in ship propulsion systems. Typically, they are calculated using numerical or experimental methods. This paper presents an experimental study through which it has been possible to estimate 24 dynamic coefficients of two hydrodynamic slide bearings operating under nonlinear conditions. During the investigation, bearing mass coefficients are identified by means of a newly developed algorithm....
-
The influence of settable parameters of switching gasoline/LPG on exhaust toxic emissions
PublicationThe main objective of the studies shown in the paper was to develop a proper strategy for settable parameters of ECU to decrease total emission of toxic components in composition of exhaust during a cold start phase. The experimental research has been performed for engine running at idle and for engine running on the chassis dynamometer (performing European Driving Test NEDC).
-
The influence of the drying process on the deformation of the beech and oak wood samples
PublicationThe influence of the drying process conditions on the deformation of the beech and oak wood. The results of the deformation of beech wood (Fagus sylvatica L.) and oak wood (Quercus robur) after drying process are presented. The drying process was carried out in the same drying schedule for each wood species. During each of schedules 40 pieces of wood were dried. The samples were divided into two groups. The first group of tested...
-
The performance of H2O, R134a, SES36, ethanol, and HFE7100 two-phase closed thermosyphons for varying operating parameters and geometry
PublicationIn this study, the influences of different parameters at performance two-phase closed thermosiphon (TPCT) was presented. It has been confirmed that the working fluid, as well as operating parameters and fill ratio, are very important factors in the performance of TPCT. The article shows characteristics of gravitational tube geometr ies, as well as the technical characteristic of the most important system components, i.e., the evaporator/condenser....
Year 2009
-
The energy test ''100 fishing deys'' of a Baltic cutter
PublicationReferat prezentuje oryginalną koncepcję testu energetycznego podczas nieprzerwanej eksploatacji kutra bałtyckiego w przeciągu 100 dni "pracy na łowisku". Test zapewni wyznaczenie na drodze obliczeniowej ilości zużytego paliwa i sprawności eksploatacyjnej układu energetycznego. Podane modele obliczeniowe uwzględniają rzeczywiste rozwiązania układów energetycznych i układów połowowych oraz warunki pracy jednostek a także wartości...
-
The idea of the heat storage in heat accumulator for car engine preheating before start = Koncepcja wykorzystania ciepła zakumulowanego w cieczy chłodzącej do wstępnego podgrzania silnika samochodu przed kolejnym rozruchem
PublicationSposób eksploatacji samochodów osobowych w miastach charakteryzuje się krótkimi przejazdami, a w przypadku pojazdów kurierów i pojazdów dostawczych również krótkimi postojami z zatrzymaniem silnika. Nowoczesne układy chłodzenia z pompą cieczy chłodzącej z napędem niezależnym od silnika stwarzają możliwość schładzania lub podgrzewania silnika zatrzymanego. Wpływ stanu cieplnego podczas rozruchu na parametry eksploatacyjne był rozważany...
-
The Method of reduction of aerodynamic forces generated in turbine blade seals
PublicationThe distibution of pressure in the seal gaps does not only affect the so called '' leakage losses'' and the turbine stage overall efficiency but also plays an important role in the generation of aerodynamic forces which may cause self-excited rotor vibrations. The paper describes a chamber seal applied for the reduction of the aerodynamic forces created in shroud seals. This kind of turbine seal was patented and tested.
Year 2015
-
The influence of high temperature wood drying conditions using air-steam mixture on its properties
PublicationThe results of properties change of beech wood after drying process are presented. The wood taken to experiments was from northern part of Pomeranian region in Poland. Before the main high temperature drying process using air-steam mixture, wood was initially dried in an open air conditions. The high temperature drying process was conducted at temperature 120oC, humidity 48%, flow rate of drying medium 2.5m/s and atmospheric pressure....
-
The selected effects of high temperature air-steam mixture wood drying
PublicationThe results of properties change of beech wood after drying process are presented. The wood taken to experiments was from northern part of Pomeranian region in Poland. Before the main high temperature drying process using air-steam mixture, wood was initially dried in an open air conditions. The high temperature drying process was conducted at temperature 120oC, humidity 48%, flow rate of drying medium 2.5m/s and atmospheric pressure....
-
The Use of Liquid Crystal Thermography an Image Processing in Heat and Fluid-Flow Research
PublicationLiquid crystal thermography (LCT) have been used in many technical, industrial and biomedical applications [1]. During over 20 years it has been successfully applied in Department of Energy and Industrial Apparatus at Gdansk University of Technology for visualization of steady-state and transient temperature fields. In order to demonstrate feasibility of LCT techniques in practical heat transfer contexts, the authors have performed...
Year 2021
-
The Influence of Loop Heat Pipe Evaporator Porous Structure Parameters and Charge on Its Effectiveness for Ethanol and Water as Working Fluids
PublicationAbstract: This paper presents the results of experiments carried out on a specially designed experimental rig designed for the study of capillary pressure generated in the Loop Heat Pipe (LHP) evaporator. The commercially available porous structure made of sintered stainless steel constitutes the wick. Three different geometries of the porous wicks were tested, featuring the pore radius of 1, 3 and 7 um. Ethanol and water as two...
-
The use of thermal imaging camera to estimate velocity profiles based on temperature distribution in a free convection boundary layer
PublicationThis work describes an attempt to assess whether the temperature field from a thermal imaging camera can be converted into a velocity field with an accuracy sufficient for qualitative conducting or describing the phenomenon, i.e. when the Navier-Stokes, Fourier-Kirchhoff and continuity equations are mutually coupled. The consequence of this link between temperature fields and velocity is the possibility to formulate the hypothesis...
Year 2002
-
The influence of rotor-stator axial gap on the aerodynamic forces generatedin the shroud clearance of a turbine stage. Part I: Pressure field
PublicationPrzedstawiono wyniki badań doświadczalnych wpływu zmiany luzu osiowego na rozkład ciśnienia w uszczelnieniu nadbandażowym stopnia powietrznej turbiny modelowej. Wykazano, że w przypadku uszczelnienia promieniowego zmiana luzu osiowego nieznacznie zmienia rozkład ciśnienia w szczelinie nadbandażowej w porównaniu ze zmianą mimośrodowości czy skośnego ustawienia osi wirnika względem osi korpusu.
-
The influence of rotor-stator axial gap on the aerodynamic forces generatedin the shroud clearance of a turbine stage. Part II: Forces and moments
PublicationPrzedstawiono wyniki badań doświadczalnych wpływu zmiany luzu osiowego na wymuszenia aerodynamiczne powstające w uszczelnieniu nadbandażowym stopnia powietrznej turbiny modelowej. Wykazano, że w przypadku uszczelnienia promieniowego zmiana luzu osiowego odgrywa niewielką rolę w generowaniu sił i momentów aerodynamicznych w szczelinie nadbandażowej w porównaniu ze zmianą mimośrodowości czy skośnego ustawienia osi wirnika względem...
-
The possibilities of using of the engine multidimensional charakteristics in fuel consumption prediction
PublicationDokument przedstawia możliwości prognozowania zużycia paliwa z wykorzystaniem wielowymiarowej charakterystyki zużycia silnika. Zdefiniowane zostały charakterystyki wielowymiarowe silnika.
Year 2012
-
The innovative experimental rig for wood steam drying at atmospheric pressure
PublicationThe high cost of fossil fuel and soaring consumer interest have encouraged people in the wood industry to look for faster and more energy-efficient methods to dry lumber. The air-steam mixture as medium of drying process was used in a laboratory kiln especially arranged for that reason. Experimental rig is based on automatic control system. At the time of drying measurements of the internal temperature, wood temperature, moisture...
Year 2010
-
The new concept of capillary forces aided evaporator for application in domestic organic rankine cycle
PublicationThis paper presents studies on the possibility of applying capillary forces induced in the porous structure to a modern design of evaporator. The potential application of such heat exchanger is for example an evaporator of the domestic micro combined heat and power (CHP) unit. One of the problems in the micro-CHP is excessive demand for pumping power. The proposed design helps in overcoming that issue. In the evaporator outlined...
-
The use of can in automation test bench to test the engine cooling system
PublicationW publikacji opisano zasady rejestracji danych pomiarowych w hamowni silnikowej do badań układów chłodzenia silników samochodowych. Założeniami projektu stanowiska było użycie standardu przesyłu danych typu CAN. Opracowano metodę dużej gęstości zapisu przesyłanych danych.
Year 2004
-
The use of liquid crystal thermography for heat, fluid flow and biomedical research.
PublicationW ostatniej dekadzie termografia ciekłokrystaliczna (TLC) i cyfrowa analiza kolorowych obrazów była z powodzeniem stosowana w różnych aplikacjach technicznych, przemysłowych i biomedycznych. Cienkie warstwy ciekłokrystaliczne zastosowano dla uzyskania lokalnych pól temperatury, współczynników przekazywania ciepła i określenia rodzaju procesu. Materiał ciekłokrystaliczny można również zastosować do wizualizacji pól temperatury i...
Year 2005
-
The Workshop on Multi-Phase Flows
PublicationPrzedstawiono ideę warsztatów ''Modelowanie przepływów wielofazowych w układach termochemicznych'' - organizowanych corocznie - od 2000 roku, przez Podsekcję Przepływów Wielofazowych Komitetu Mechaniki PAN. Omówiono tematykę VI Warsztatów, które były poświęcone głównie metodom eksperymentalnym.
-
Theoretical and experimental flow analysis through the model water turbine stage
PublicationW artykule zaprezentowano teoretyczną i eksperymentalną analizę przepływu przez stopień modelowej turbiny wodnej. Przedstawiono rozwiązanie zadania prostego dla dwuwymiarowego modelu przepływu. Zaprezentowano przykład numerycznej symulacji przepływu za pomocą komeryjnych kodów obliczeniowych oraz porównano wyniki symulacji numerycznych przepływu z wynikami badań eksperymentalnych.
Year 2006
-
Theoretical and experimental research of heat and mass transfer in adsorption process in dac systems
PublicationPrzedstawiono badania wymiany ciepła i masy w stałych adsorpcyjnych elementach wykonanych na bazie silikażelu. Zaprezentowano również informacje dotyczące osuszania w systemach klimatyzacyjnych. Na zkończenie pokazano wyniki numerycznej symulacji i skojarzonej wymiany ciepła i masy w chłodzonym osuszaczu.
Year 2003
-
Theoretical investigations into flows in rotor blade shroud clearance
PublicationPrzedstawiono wyniki obliczeń programem Fluent przepływów w uszczelnieniu nadbandażowym stopnia turbinowego przy różnym mimośrodowym położeniu osi wirnika względem osi korpusu. Wyznaczone numerycznie rozkłady ciśnienia w uszczelnieniu i generowane tam siły aerodynamiczne porównano z rezultatem badań przeprowadzonych na powietrznej turbinie modelowej.