Wyszukiwarka
ISSN:
eISSN:
Dyscypliny:
- inżynieria biomedyczna (Dziedzina nauk inżynieryjno-technicznych)
- inżynieria chemiczna (Dziedzina nauk inżynieryjno-technicznych)
- inżynieria lądowa, geodezja i transport (Dziedzina nauk inżynieryjno-technicznych)
- inżynieria materiałowa (Dziedzina nauk inżynieryjno-technicznych)
- inżynieria mechaniczna (Dziedzina nauk inżynieryjno-technicznych)
- biologia medyczna (Dziedzina nauk medycznych i nauk o zdrowiu)
- nauki farmaceutyczne (Dziedzina nauk medycznych i nauk o zdrowiu)
- nauki leśne (Dziedzina nauk rolniczych)
- biotechnologia (Dziedzina nauk ścisłych i przyrodniczych)
- nauki chemiczne (Dziedzina nauk ścisłych i przyrodniczych)
Punkty Ministerialne: Pomoc
| Rok | Punkty | Lista |
|---|---|---|
| Rok 2025 | 100 | Ministerialna lista czasopism punktowanych 2024 |
| Rok | Punkty | Lista |
|---|---|---|
| 2025 | 100 | Ministerialna lista czasopism punktowanych 2024 |
| 2024 | 100 | Ministerialna lista czasopism punktowanych 2024 |
| 2023 | 100 | Lista ministerialna czasopism punktowanych 2023 |
| 2022 | 100 | Lista ministerialna czasopism punktowanych (2019-2022) |
| 2021 | 100 | Lista ministerialna czasopism punktowanych (2019-2022) |
| 2020 | 100 | Lista ministerialna czasopism punktowanych (2019-2022) |
| 2019 | 100 | Lista ministerialna czasopism punktowanych (2019-2022) |
| 2018 | 35 | A |
| 2017 | 35 | A |
| 2016 | 30 | A |
| 2015 | 30 | A |
| 2014 | 35 | A |
| 2013 | 30 | A |
| 2012 | 35 | A |
| 2011 | 35 | A |
| 2010 | 27 | A |
Model czasopisma:
Punkty CiteScore:
| Rok | Punkty |
|---|---|
| Rok 2023 | 6.9 |
| Rok | Punkty |
|---|---|
| 2023 | 6.9 |
| 2022 | 6.1 |
| 2021 | 5.6 |
| 2020 | 5 |
| 2019 | 4.8 |
| 2018 | 3.9 |
| 2017 | 4.2 |
| 2016 | 4 |
| 2015 | 3.6 |
| 2014 | 3.3 |
| 2013 | 3.2 |
| 2012 | 4 |
| 2011 | 3.6 |
Impact Factor:
Sherpa Romeo:
Prace opublikowane w tym czasopiśmie
Filtry
wszystkich: 7
Katalog Czasopism
Rok 2024
-
Experimental study of the impact of notches and holes made in the front edge of adherends on the properties of static and fatigue strength of adhesive joints
PublikacjaThe paper presents the results of experimental studies aimed at determining the effect of holes and notches at the front edge of adherends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets joined with Araldite 2014-2 epoxy adhesive were tested. Comparative tests of static strength in the shear test as well as high-cycle fatigue strength tests were carried out. Joints with three holes with a diameter...
Rok 2017
-
Carboxymethylated polysaccharide-based films as carriers for acrylic pressure-sensitive adhesives
Publikacja
Rok 2012
-
Experimentation, material modelling and simulation of bonded joints with a flexible adhesive
PublikacjaThe paper deals with material parameters identification of a flexible adhesive and the numerical simulation of its behaviour in a single lap bonded joint. The material modelling was based on the simple shear and tensile-shear laboratory tests of the bonded joints made of thin aluminium and polyurethane plates with the flexible adhesive Terostat MS 9360 manufactured by Henkel AG & Co. The adhesive was considered as a hyperelastic...
-
Monitoring of crosslinking of a DGEBA-PAMAM adhesive in composite/aluminium bonded joint using mechanical and ultra-sound techniques
PublikacjaAdhesive cure is an important and determining aspect of strength and stability of bonded structures. Crosslinking of the polymer leads to the adhesive strength, stiffness and durability. Depending on the resin and curing agent used, cure time can vary from minutes to weeks, even then 100% crosslinking not being guaranteed. Standard methods based on dynamic mechanical analysis (DMA) or calorimetric techniques (DSC, DTA) are valuable...
-
Using of carbon nanotubes and nano carbon black for electrical conductivity adjustment of pressure-sensitive adhesives
Publikacja
Rok 2011
-
Adhesive compliance effect in mode I separation:Profilometry approach
PublikacjaThe effect of adhesive compliance on the deflection of a loaded, bonded beam was studied using laser profilometry. Experimental data obtained were compared with both Euler-Bernoulli (encastré) and Winkler (one parameter elastic foundation) models. A third, analytical, 2D model, based on shear within the adhesive layer (two parameter elastic foundation), was introduced. Finite element analysis (FEA) was also used to study the effect...
Rok 2009
-
Accurate and continuous adhesive fracture energy determination using an instrumented wedge test
PublikacjaThe wedge test and the related double cantilever beam test are practical methods of assessing structural adhesive fracture energy. In the former, and to a lesser extent the latter, a recognised problem is the difficulty of following the length of the growing crack, required to calculate fracture energy with any accuracy. We present a novel method of measurement of crack length that has the advantages of being accurate and allowing...
wyświetlono 1150 razy