- Inżynieria biomedyczna (Dziedzina nauk inżynieryjno-technicznych)
- Inżynieria lądowa i transport (Dziedzina nauk inżynieryjno-technicznych)
- Inżynieria materiałowa (Dziedzina nauk inżynieryjno-technicznych)
- Inżynieria mechaniczna (Dziedzina nauk inżynieryjno-technicznych)
- Nauki farmaceutyczne (Dziedzina nauk medycznych i nauk o zdrowiu)
- Nauki chemiczne (Dziedzina nauk ścisłych i przyrodniczych)
- Nauki fizyczne (Dziedzina nauk ścisłych i przyrodniczych)
Punkty Ministerialne: Pomoc
|Rok 2022||70||Lista ministerialna 2019|
|2022||70||Lista ministerialna 2019|
|2021||70||Lista ministerialna 2019|
|2020||70||Lista ministerialna 2019|
|2019||70||Lista ministerialna 2019|
Prace opublikowane w tym czasopiśmie
The friction stir welding method is increasingly attracting interest in the railway sector due to its environmental friendliness, low cost, and ease of producing high-quality joints. Using aluminum alloys reduces the weight of structures, increasing their payload and reducing fuel consumption and running costs. The following paper presents studies on the microstructure, strength, and corrosion resistance of AA6082 aluminum alloy...
Cold-spray coatings were produced by FeCoCrNiMn high-entropy alloy powders deposited on carbon steel substrate. The coatings were realized at intermediate temperature and high pressure (at 1100 °C and 7 MPa). The coating microstructure was characterized by scanning electron microscopy and X-ray diffraction, revealing a very dense deposition and high flattening ratio of the splatted particles. This had a large influence on the...
Correlation between Fractal Dimension and Areal Surface Parameters for Fracture Analysis after Bending-Torsion FatiguePublikacja
This paper investigates the fracture surface topography of two steel and aluminum alloys subject to bending-torsion fatigue loadings, as well as their susceptibility to fatigue performance and failure mechanisms. Using fracture surface topography data analysis, elements with different geometries were elaborated. A correlation between the fractal dimension, other selected parameters of surface topography such as areal Sx, and...
In this study, the impact of pseudo-random non-proportional bending-torsion fatigue loadings proportion on the fatigue life and the fracture surface topography was analyzed. Investigation was carried out for 24 specimens made of S355J2 steel with 11 different ratios of maximum stresses λ. For these cases, after the fatigue tests, the surface topography measurements were carried out using an optical profilometer, using the focus...
Mechanical and Microstructural Characterization of TIG Welded Dissimilar Joints between 304L Austenitic Stainless Steel and Incoloy 800HT Nickel AlloyPublikacja
In this article, the mechanical properties and microstructure of 304L austenitic stainless steel/Incoloy 800HT nickel alloy dissimilar welded joints are investigated. The joints were made of 21.3 mm × 7.47 mm tubes using the TIG process with the use of S Ni 6082 nickel filler metal. No welding imperfections were found and high strength properties of joints were obtained, meeting the assumed acceptance criteria of the product’s...
Monitoring Steel Bolted Joints during a Monotonic Tensile Test Using Linear and Nonlinear Lamb Wave Methods: A Feasibility StudyPublikacja
The structural integrity of steel bolted joints may be compromised due to excessive loading. Therefore, condition assessment and the detection of potential defects before they cause a failure have become a major issue. The paper is focused on the condition monitoring of a bolted lap joint subjected to progressive degradation in a tensile test. The inspection used Lamb waves propagated through the overlap area. Wave propagation...
wyświetlono 520 razy