Wyszukiwarka
dr inż. Paweł Ziółkowski
Zatrudnienie
- Adiunkt w Instytut Energii
Publikacje
Filtry
wszystkich: 82
Katalog Publikacji
Rok 2013
-
FURTHER REMARKS ON THE NEO-CLASSICAL NAVIER-STOKES EQUATIONS
PublikacjaThe seminal Navier-Stokes equations have been stated yet before creation of principles of thermodynamics and the first and second laws. In the literature there is the common opinion that the Navier-Stokes equations cannot be taken as a thermodynamically correct model of “working fluid” which is able to describe transformation of “ heat” into “work” and vice versa. Therefore, in the paper, a new exposition of thermodynamically...
Rok 2014
-
An advanced Thermal-FSI approach to flow heating/cooling
PublikacjaActually, two-way thermal-energy exchange between working fluid and solid material of a casing is a leading problem for modern – semi automatic – design techniques. Many questions should be solved, especially, the turbulent mode of thermal energy transport both in fluid and solid, should be re-examined and reformulated from the primary principles. In the present paper, a group of researchers from Energy Conversion Department of...
-
ANALIZA TECHNICZNO-ENERGETYCZNA PREFEROWANYCH OBIEGÓW TERMODYNAMICZNYCH MOBILNYCH WYSOKOTEMPERATUROWYCH SIŁOWNI JĄDROWYCH
PublikacjaArtykuł przedstawia analizę techniczno-energetyczną moŜliwości współpracy preferowanych obiegów turbin cieplnych duŜych mocy z wysokotemperaturowym reaktorem jądrowym chłodzonym helem w zastosowaniach mobilnych. Reaktory jądrowe wysokotemperaturowe (HTR) stwarzają moŜliwość podnoszenia parametrów obiegów parowych do poziomu bloków nadkrytycznych, jak równieŜ zastosowania obiegu Joule’a-Braytona w energetyce jądrowej. W miarę zaostrzania norm...
-
Combined operation of 900MW power plant with the ORC through the bleed steam extraction point and CO2 recovery system
PublikacjaThe work presented here is aimed at utylisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90 C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach...
-
DO WE NEED NAVIER NUMBER? – FURTHER REMARKS AND COMPARISON WITH ANOTHER DIMENSIONLESS NUMBERS
PublikacjaThis paper presents a role of the Navier number (Na-dimensionless slip-length) in universal modelling of flow reported in micro- and nano-channels like: capillary biological flows, fuel cell systems, micro-electro-mechanical systems and nano-electro-mechanical systems. Similar to another bulk-like and surface-like dimensionless numbers, the Na number should be treated as a ratio of internal viscous to external viscous momentum...
-
Możliwości dostosowania istniejących bloków gazowo-parowych do utylizacji gazu niekonwencjonalnego w tym gazu łupkowego
PublikacjaW pracy omówiono modyfikację turbiny gazowej dostosowując ją do spalania gazu niekonwencjonalnego. Rozpatrzono aspekty termodynamiczne utylizacji gazu łupkowego we wspomnianej instalacji. W oparciu o analizy termodynamiczne określono sprawność obiegu gazowo-parowego. Analiza obiegu cieplnego została przeprowadzona za pomocą kodów CFM. Motywacją do podjęcia niniejszej pracy jest potrzeba dywersyfikacji źródeł energii w tym również...
-
Navier number and transition to turbulence
PublikacjaThe motivation behind this article is to explain a role of the Navier number (Na -dimensionless slip-length) in prediction of closures for laminar to turbulent transition undergoing via eddies detachment from the slip layer in nano-cannals. Additionally the role of the Navier number Na in universal modeling of phenomenon of enhanced mass flow rate reported in micro- and nano-channels has been explained. The Na number should be...
-
Revalorization of the Szewalski binary vapour cycle
PublikacjaThe aim of the paper is to revalorizate of the Szewalski binary vapour cycle by analysing thermodynamical and operational parameters of this cycle. This was carried by accessible numerical CFM (Computational Flow Mechanics) codes type, by step-by-step modeling of separates apparatus. The binary vapour cycle is providing steam as the working fluid in the high temperature part of the cycle, while another fluid - a low boiling point...
Rok 2015
-
Exergy Losses in the Szewalski Binary Vapor Cycle
PublikacjaIn this publication, we present an energy and exergy analysis of the Szewalski binary vapor cycle based on a model of a supercritical steam power plant. We used energy analysis to conduct a preliminary optimization of the cycle. Exergy loss analysis was employed to perform a comparison of heat-transfer processes, which are essential for hierarchical cycles. The Szewalski binary vapor cycle consists of a steam cycle bottomed with...
Rok 2016
-
Analysis of possible application of high-temperature nuclear reactors to contemporary large-output steam power plants on ships
PublikacjaThis paper is aimed at analysis of possible application of helium to cooling high-temperature nuclear reactor to be used for generating steam in contemporary ship steam-turbine power plants of a large output with taking into account in particular variable operational parameters. In the first part of the paper types of contemporary ship power plants are presented. Features of today applied PWR reactors and proposed HTR reactors...
Rok 2018
-
Ku zeroemisyjnej energetyce gazowej
PublikacjaW pracy krótko omówiono trendy wprowadzane w obiegach gazowych z zastosowaniem oksyspalania. Następnie przed-stawiono rozwiązanie nowego układu opartego na wykorzystaniu dwóch urządzeń o wzmożonej konwersji energii, a mia-nowicie „mokrej komory spalania” i „skraplacza natryskowo-strumieniowego”. Zaproponowany obieg gazowo-parowy realizowany jest w jednej turbinie, która ma zalety zarówno turbiny gazowej (wysokie temperatury wlotowe)...
-
NUMERICAL ANALYSIS OF SPECIES DIFFUSION AND METHANOL DECOMPOSITION IN THERMOCATALYTIC REACTOR BASED ON THE INTERMETALLIC PHASE OF Ni3Al FOR LOW REYNOLDS NUMBERS
PublikacjaNumerical modelling of hydrogen production by means of methanol decomposition in a thermocatalytic reactor using corrugated foil made of the Ni3Al intermetallic phase is shown in the paper. Experimental results of the flow analysis of mixtures containing helium and methanol in a thermocatalytic reactor with microchannels were used for the initial calibration of the CFD calculations (calculations based on the Computational Fluid...
Rok 2019
-
A study of a compact high-efficiency zero-emission power plant with oxy-fuel combustion
PublikacjaThis paper discusses the application of global trends in gas cycles technology using oxy-fuel combustion. This is followed by a demonstration of a design solution for a new cycle with two enhanced energy-converting devices, namely a wet combustion chamber and a spray-ejector condenser. The proposed gas and steam cycle unit is contained within a single turbine, whose benefits combine those offered by gas turbines (high inlet temperatures)...
-
An energetic analysis of a gas turbine with regenerative heating using turbine extraction at intermediate pressure - Brayton cycle advanced according to Szewalski's idea
PublikacjaIn this paper, a modification of a simple gas turbine into the Brayton cycle with regenerative heating, using turbine extraction at intermediate pressure, is presented. The main concept of the retrofitting is based on the transfer of heat from the turbine exhaust gases to the air entering the combustion chamber. The extracted gas transfers heat to air via the divided regenerative heat exchanger and after that is compressed and...
-
Analiza zmienności generacji energii elektrycznej w okresie pierwszych pięciu miesięcy 2019 r. ze szczególnym uwzględnieniem generacji energii ze źródeł wiatrowych
PublikacjaW artykule przedstawiono zagadnienia związane z szeroko pojętym rozwojem energetyki wiatrowej. Omówiono stan rozwoju energetyki wiatrowej na świecie. Na podstawie dostępnych badań przybliżono także zagadnienia związane z czynnikami wpływającymi na rozwój odnawialnych źródeł energii oraz ich oddziaływanie na środowisko naturalne. Główny nacisk położono jednakże na analizę zjawisk w pracy Krajowego Systemu Elektroenergetycznego (KSE)...
-
Extremal thermal loading of a bifurcation pipe
PublikacjaThe subject of considerations is a spherical bifurcation pipe of a live steam made of steel P91, which is an element of a block of coal-fired power plant working with a 18K370 turbine. As experience shows, it is a very sensitive element of the boiler pipelines. An extreme work scenario for such a block has been adopted, in which the turbine is shutting down to a warm state three times in 24 hours. This is an action dictated by...
-
Maksymalna elastyczność pracy bloków parowych
PublikacjaW artykule przedstawiono propozycję przyspieszenia startów turbiny parowej poprzez właściwe doprowadzanie pary w trakcie stanów niestacjonarnych. Badano najbardziej wytężone miejsca w urządzeniu, przy uwzględnieniu tradycyjnej hipotezy Hubera-Missesa-Hencky, jak i hipotezy Burzyńskiego. W przypadku licznych startów coraz większe znaczenie odgrywają naprężenia termiczne, dla których najważniejsze są składowe normalne naprężeń, w...
-
Mathematical modeling of hydrogen production performance in thermocatalytic reactor based on the intermetallic phase of Ni3Al
PublikacjaThe main goal of the following work is to adjust mathematical modelling for mass transfer, to specific conditions resulting from presence of chemical surface reactions in the flow of the mixture consisting of helium and methanol. The thermocatalytic devices used for decomposition of organic compounds incorporate microchannels coupled at the ends and heated to 500 oC at the walls regions. The results of the experiment were compared...
-
Nowa koncepcja poprawy elastyczności bloków parowych z zastosowaniem magazynów pary
PublikacjaCelem niniejszej pracy jest krótki przegląd sposobów magazynowania energii i odniesienie się do sposobu, który byłby najdogodniejszy dla bloków parowych klasy 370-390 MWe. W niniejszej pracy zaproponowano innowacyjny magazyn pary, który jest integralną częścią obiegu parowego i dzięki temu szybko odpowiada na zmiany zapotrzebowania na energię elektryczną, a zatem może usprawniać świadczenia usługi regulacji pierwotnej przy jednoczesnym...
-
On energy, exergy, and environmental aspects of a combined gas-steam cycle for heat and power generation undergoing a process of retrofitting by steam injection
PublikacjaThe paper presents a study of retrofitting of a combined heat and power (CHP) plant aimed to increase the electric to heating power ratio. The modification would involve diverting part of the steam to the gas turbine, instead of letting it go to the steam turbine, using injection technique into a combustion chamber. Therefore, two potential retrofitting approaches are analyzed: steam injection gas turbine (STIGT) and combined steam...
-
On the production of electricity in Poland using a geothermal binary power plant - A thermodynamic overview - Part I
PublikacjaPoland has a significant potential of geothermal energy. However, the high-temperature sources that are needed to drive power plants are found in relatively few places. Therefore, the objective of this paper is to consider any location in the northern part of Poland as a possible place to build a binary power plant. A scientific research was confirmed the existence of an elevated temperature gradient in this region. The hot rocks...
-
Porous structures in aspects of transpirating cooling of oxycombustion chamber walls
PublikacjaA wet oxycombustion chamber, which must be effectively cooled due to high temperature evolved during the oxy-combustion process, by using the phenomena of Reynolds thermal transpiration and Navier slip velocity. Closures needed to execute mass flow rate in a microchannel, which should be treated as a single porous structure in the walls of the combustion chamber, have been obtained by applying a local 3D approach. The Navier-Stokes...
-
The thermal effort during marine steam turbine flooding with water
PublikacjaThe work discussed an extreme case of cooling a steam turbine. The ship's steam turbine was used as an example. In marine transport units with low-speed engines dominate, however, there are also units with steam turbines. An example of analysed marine steam turbine is shown in Fig. 1. When considering the issue of cooling steam turbines, it is necessary to estimate the extreme conditions that may occur during operation of the turbine....
-
Thermal utilization of meat and bone meals. Performance analysis in terms of drying process, pyrolysis and kinetics of volatiles combustion
PublikacjaA development of technology of thermal utilization requires a thorough knowledge of the physicochemical properties, as well as kinetics of combustion of volatiles and char. Due to waste management regulations the meat and bone meal (MBM) is regarded as biofuel constituting one of the alternatives to fossil fuels in the energy market. MBM is a heterogeneous material that may consist of several different fractions. The extensive...
-
Thermodynamic analysis of the Compressed Air Energy Storage system coupled with the Underground Thermal Energy Storage
PublikacjaImprovement of flexibility is one of the key challenges for the transformation of the Polish Power System aiming at a high share of renewable energy in electricity generation. Flexible and dispatchable power plants will contribute to this ongoing transformation process as they compensate for fluctuations in electricity generation from renewable energy sources such as wind and photovoltaics. In this context, CAES storage tanks are...
Rok 2020
-
A concept of zero-dimensional and three-dimensional thermodynamic modelling of steam storage in a steam cycle
PublikacjaThis work presents the thermodynamic model of steam storage in a steam cycle. The innovative steam storage is an integral part of the unit and thus responds quickly to changes in load. This enhances the primary control reserve while maintaining high efficiency of energy conversion. With regard to power plants, it improves the operational safety of generation units, as it prevents boiler and turbines overload in the case of steep...
-
A novel concept of negative CO2 emission power plant for utilization of sewage sludge
PublikacjaCarbon Capture and Storage (CSS) technology is considered an important “bridge technology”, allowing effective abatement of CO2 emissions for power units using fossil fuels. However, if biomass is used in a power plant, equipped with CCS system, negative CO2 emissions can be achieved. In practice, wide development of such technologies would enable not only reduction of CO2 emissions, but also reversal of the harm done so far. In...
-
ANALIZA MAGAZYNOWANIA ENERGII W UKŁADZIE CAES SPRZĘŻONYM Z GRUNTOWYM MAGAZYNEM CIEPŁA
PublikacjaElastyczne i dyspozycyjne elektrownie przyczynią się do trwającego procesu transformacji Polskich Sieci Elektroenergetycznych SA (PSE), ponieważ kompensują wahania energii elektrycznej wytwarzanej z odnawialnych źródeł energii, takich jak wiatr i fotowoltaika. W tym kontekście zasobniki CAES (Compressed Air Energy Storage) są obecnie jedyną alternatywą dla magazynów z wykorzystaniem elektrowni szczytowo-pompowych ze względu na...
-
Analiza zmienności generacji energii elektrycznej w 2019 r. ze szczególnym uwzględnieniem generacji energii ze źródeł wiatrowych II połowa roku i okres pandemii w 2020 jako czynnik nieprzewidywalny
PublikacjaW artykule przedstawiono zagadnienia związane z szeroko pojętym rozwojem energetyki wiatrowej. Omówiono stan rozwoju energetyki wiatrowej na świecie. Na podstawie dostępnych badań przybliżono także zagadnienia związane z czynnikami wpływającymi na rozwój odnawialnych źródeł energii oraz ich oddziaływania na środowisko naturalne. Główny nacisk położono jednakże na analizę zjawisk w pracy Krajowego Systemu Elektroenergetycznego (KSE)...
-
Analysis of electricity generation variability in 2019 with special consideration of electrical energy generation from wind sources.
PublikacjaThis article presents issues related to the broadly understood development of wind energy. The state of the art of wind energy in the world has been discussed. This paper also shows issues related to factors affecting the development of renewable energy sources and their impact on the natural environment on the basis of available research. The focus is, however, on the critical analysis of phenomena in the data of the Transmission...
-
Assessment of the Effective Variants Leading to Higher Efficiency for the Geothermal Doublet, Using Numerical Analysis‒Case Study from Poland (Szczecin Trough)
PublikacjaNumerical models of geothermal doublet allows us to reduce the high risk associated with the selection of the most eective location of a production well. Furthermore, modeling is a suitable tool to verify possible changes in operational geothermal parameters, which guarantees liveliness of the system. An appropriate selection of software as well as the methodology used to generate numerical models significantly aects the quality...
-
Carbon Dioxide Recovery Skid
PublikacjaIn the face of tightening climate regulations, the adoption of carbon dioxide recovery systems is inevitable. Modular process skid units have been widely adopted across the industry. The gas-steam power plant skid unit with the carbon dioxide recovery system was described. The proposed skid module consists of the compact cycle with the oxy-combustion and the carbon dioxide capture skid unit producing pure compressed CO2. The compactness...
-
Comparative study of a bottoming SRC and ORC for Joule–Brayton cycle cooling modular HTR exergy losses, fluid-flow machinery main dimensions, and partial loads
PublikacjaEnergy conversion efficiency increase in power plants with high-temperature gas-cooled reactors via implementation of the bottoming cycle was investigated under nominal and minimal thermal load of a high-temperature reactor (HTR). Heat transfer surface area and turbine outlet volumetric flow rate in bottoming cycles was also investigated. Water and two low-boiling point working fluids (ammonia and ethanol) were analyzed. Analyzed...
-
Computational Fluid Dynamics Simulation of Gas–Liquid Multiphase Flow in T-junction for CO2 Separation
PublikacjaThe article presents the results of a computational fluid dynamics (CFD) analysis of gas-liquid multiphase flow. The simulation was conducted using CFD code and the Euler–Euler approach. The presented study relates to the non–reactive, steady-state, turbulent flow of water and carbon dioxide mixture in a 3D pipe. Separation phenomenon between phases is observed. The solution was obtained using a mixture model. Different values...
-
Neoclassical Navier–Stokes Equations Considering the Gyftopoulos–Beretta Exposition of Thermodynamics
PublikacjaThe seminal Navier-Stokes equations were stated even before the creation of the foundations of thermodynamics and its first and second laws. There is a widespread opinion in the literature on thermodynamic cycles that the Navier-Stokes equations cannot be taken as a thermodynamically correct model of a local "working fluid", which would be able to describe the conversion of "heating" into "working" (Carnot's type cycles) and vice...
-
On coertia and inertia in aspects of Natanson’s nonlinear extended thermodynamics
PublikacjaIn this article, the previously underrepresented contributions of Natanson to the field of thermodynamics have been presented. In order to identify a source of irreversibility at Nature, Natanson introduced the concept of Coertia, which is similar to inertia. Natanson’s Coertia is a fundamental property of space that is responsible for every irreversible phenomena in matter, as well as in the electromagnetic and gravitational fields....
-
On design and analysis of flow characteristics of the last stage of gas-steam turbine
PublikacjaResearch regarding blade design and analysis of flow have been conducted for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics (CFD) and computational flow mechanics (CFM). Currently a combination of mentioned methods is used for design of turbine blades. These methods enabled us to improve flow efficiency...
-
POPRAWY ELASTYCZNOŚCI PRACY BLOKÓW PAROWYCH I GAZOWO-PAROWYCH PRZEZ ZASTOSOWANIE MAGAZYNU PARY
PublikacjaCelem niniejszej pracy jest krótki przegląd sposobów magazynowania energii i odniesienie się do sposobu, który byłby najdogodniejszy dla bloków zawodowych parowych i gazowo-parowych. W niniejszej pracy zaproponowano innowacyjny magazyn pary, który jest integralną częścią obiegu parowego, bądź gazowo-parowego i dzięki temu szybko odpowiada na zmiany zapotrzebowania na energię elektryczną, a zatem może usprawniać świadczenia usługi...
-
Thermal failure of a second rotor stage in heavy duty gas turbine
PublikacjaThe impulse mode of operation and the supply of various types of fuels causes frequent failures even in the heavy duty gas turbines. The paper presents the ravages of second rotor stage failure in a gas turbine. The excessive thermal elongation rise caused by fuel change was indicated as the main cause. We applied nonlinear numerical analysis, preceded by thermodynamic calculations of the turbine and visual inspection of the effects...
Rok 2021
-
A study of jet impingement cooling enhancement by concave and convex heat sink shape modifications
PublikacjaThe rising demand for efficient cooling technologies is a strong driver of extensive research in this area. This trend is particularly strong in turbines and microprocessors technology. Presented study is focused on the jet impingement cooling concept, which is used in various configurations for many years. The potential of the heat sink shape modification is not yet fully explored. Available literature suggests that average Nusselt...
-
Comprehensive thermodynamic analysis of steam storage in a steam cycle in a different regime of work: A zero-dimensional and three-dimensional approach
PublikacjaDue to the current trends aiming to reduce carbon dioxide emissions by increasing the use of renewable energy sources, changes are required in the operation of coal-fired steam units. The unstable nature of renewable energy sources, depending on weather conditions, means that the amount of energy produced varies and is not always in line with peak demand. To ensure the security and stability of energy supplies in the energy system,...
-
Comprehensive thermodynamic analysis of the CAES system coupled with the underground thermal energy storage taking into account global, central and local level of energy conversion
PublikacjaA key aspect of CAES is the optimal configuration of the thermodynamic cycle. In this paper, the situation of cooperation between the current conventional power plants and wind farms is analyzed, and then, based on thermodynamic models, the process of storing thermal and electrical energy in the CAES system coupled with a heat storage and recovery is developed. Therefore, three levels can be distinguished, namely: the global level...
-
Computational fluid dynamics simulation of heat transfer from densely packed gold nanoparticles to isotropic media
PublikacjaThis work aims to determine and compare heat generation and propagation of densely packed gold nanoparticles (Au NPs) induced by a resonant laser beam (532 nm) according to the Mie theory. The heat flux propagation is transferred into the materials, which here are: silica glass; soda-lime-silica glass; borosilicate glass; polymethyl methacrylate (PMMA); polycarbonate (PC); and polydimetylosiloxane (PDMS). This analysis aims to...
-
Design and computational fluid dynamics analysis of the last stage of innovative gas-steam turbine
PublikacjaResearch regarding blade design and analysis of flow has been attracting interest for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics and computational flow mechanics. Currently a combination of mentioned methods is used for the design of turbine blades. These methods enabled us to improve flow efficiency...
-
Different design aspects of an Organic Rankine Cycle turbine for electricity production using a geothermal binary power plant
PublikacjaIn recent years, pressure has been growing to increase the share of renewable energy sources in electricity generation, which may offer opportunities for the development of geothermal energy in regions that have been so far considered unprofitable in this respect. One such country currently undergoing an energy transition is Poland in which low-temperature geothermal resources are currently used for district heating and recreation...
-
Heat exchange enhancement of jet impingement cooling with the novel humped-cone heat sink
PublikacjaJet impingement cooling technology is applicable to control temperature of devices, where very high heat flux is generated within a small area. This paper is about the improvement of the jet impingement cooling efficiency by the heat sink geometry modification. Two reference cases were sourced from the literature – flat heat sink and modified one with cone in the jet stagnation region. Such a change improves cooling capability...
-
OPTIMIZATION OF THE LAST STAGE OF GAS-STEAM TURBINE USING A HYBRID METHOD
PublikacjaThis paper relates to the CFD calculation of a new turbine type which is in the phase of theoretical analysis, because the working fluid is a mixture of steam and gas generated in wet combustion chamber. At first, this article concentrates on a possibility of streamlining the flow efficiency of a last stage of axial turbine working on gas-steam mixture using a hybrid of the particle swarm optimization algorithm with the Nelder-Mead...
-
Revalorisation of the Szewalski’s concept of the law of varying the last-stage blade retraction in a gas-steam turbine
PublikacjaThe article presents the implementations of the free vortex law to the blade of the last stage of a gas-steam turbine. First, a thermodynamic analysis was carried out, determining the parameters at the inlet, then the number of stages of the high and low-pressure part of the turbine was constructed, together with the kinematics and velocity vectors for subsequent stages of the axial turbine. The last step of article was to take...
-
The efficiency of turbomachinery in the zero-and three-dimensional approaches
PublikacjaEfficiency of turbomachinery is usually defined using an isentropic process. This approach provides a reliable reference point only when pressure and temperature measurements are available, e.g. at the casing inlet and outlet. In the case of a single stage internal efficiency determination the reference point is difficult. Computational fluid dynamics allows for an exact calculation of values of losses occurring in a turbine...
-
The Staged Combustion of Meat-and-Bone Meal:The Characteristics of Conversion Sub-processes and Large-Scale Process Outputs
Publikacjat Organic waste has been playing an increasingly important role in the energy market as those that may support the economies in pursuing towards decarbonization by increasing the share of renewables in the overall energy balance. In this group of alternative fuels, meat-and-bone meals being a post-production waste of the steadily developing meat industry, constitute a considerable proportion. Though they are rich in minerals, their...
wyświetlono 5729 razy