Filtry
wszystkich: 1127
wybranych: 569
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: ENGINEERING MATERIALS
-
Use of Neural Networks in Diagnostics of Rolling-Element Bearing of the Induction Motor
PublikacjaBearing defect is statistically the most frequent cause of an induction motor fault. The research described in the paper utilized the phenomenon of the current change in the induction motor with bearing defect. Methods based on the analysis of the supplying current are particularly useful when it is impossible to install diagnostic devices directly on the motor. The presented method of rolling-element bearing diagnostics used indirect...
-
Numerical Comparison of Damping Amplification Effects Obtained in Neighborhood of a Mechanism Singular Position - Viscous and Electromagnetic Cases
PublikacjaIn the paper, results of numerical investigations are presented. A continuous beam is considered as the main vibrating element. Two energy dissipations methods are compared: viscous dampers and DC generators. To increase the damping effectiveness, velocity amplification is proposed, i.e., a mechanism is introduced between the beam and the damping element, and the mechanism configuration is set as closed to the singular position...
-
Selected Problems of Cogeneration Energy Systems Designing, Fueled with Landfill Biogas
PublikacjaThe article discusses the impact of the quality of biogas fuel for operation of generating sets with internal combustion engines. There are presented selected investigation results of landfill biogas fueled gensets operation. The article includes also discussion of the possibility of increasing the efficiency of biogas fuelled cogeneration systems. It also presents guidelines for the optimal design of landfill biogas fueled engines,...
-
Hertzian Crack Propagation in Ceramic Rolling Elements
PublikacjaThe properties of ceramics are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such crack are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations are based on a three dimensional model for the ring crack propagation. The stress intensity factors along crack...
-
Lean Six Sigma in French and Polish Small and Medium-Sized Enterprises - The Pilot Research Results
PublikacjaThe article presents results of the research conducted in Polish and French small and medium-sized enterprises referring to the context of the implementation and application of the concept of Lean Six Sigma. The research was conducted in the form of case studies, observations and individual interviews. The pilot studies led to the identification of the needs, expectations, concerns and experiences of these companies. At the same...
-
Structure and Interactions in Chitosan Composites
Publikacja -
The Rolling Contact Fatigue of PVD Coated Spur Gears
Publikacja -
The Effect of Temperature on Wear Mechanism of the AlCrN Coated Components
Publikacja -
The Scuffing Resistance of WC/C Coated Spiral Bevel Gears
Publikacja -
Guided waves in steel rails - experimental works and wavelet signal processing
PublikacjaW artykule zaprezentowano analizę falkową pomierzonych eksperymentalnie fal sprężystych wzbudzanych w szynach kolejowych.
-
Detection of delamination in multi layer composite beams.
PublikacjaW pracy przedstawiono model belki kompozytowej z delaminacją. Omówiono czynniki propagacji fali sprężystej w belce i możliwości wykorzystania zmian w propagującej fali wywołanych delaminacją do jej detekcji.
-
Shaft Misalignment Influence on Water Lubricated Turbine Sliding Bearings with Various Bush Modules of Elasticity
PublikacjaW artykule przeanalizowano wpływ wielkości przenoszenia osi wału względem panwi na nośność łożyska. Analizie poddano łożyska z odmiennymi rodzajami panwi o różnej sztywności.
-
Novel Design of an Ocean Wave Power Device
PublikacjaW artykule przedstawiono nowoczesną boję energetyczną o opatentowanej konstrukcji. Omówiono jej konstrukcję oraz przedstawiono problemy konstrukcyjne i badawcze. W ostatniej części artykułu przedstawiono wyniki badań wykonanych na modelu w basenie modelowym.
-
The Influence of Gas Mixture in the Glow-Discharge Nitriding Process of Austenitic Stainless Steel on Characteristic of Nitrided Cases
PublikacjaAustenitic stainless steels characterize with excellent corrosion resistance, although low mechanical properties. In many cases that limits their exploitation in industrial applications. Moreover, austenitic stainless steel is susceptible to local corrosion in the presence of halide ions. In present works, it was emphasized that the nitriding of austenitic stainless steels gives some potential abilities to obtain beneficial effect...
-
A New Technique of Spine Disease Treatment Supported by ADRSK1 Device
Publikacja -
Numerical analysis of crack propagation in silicone nitride
PublikacjaThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculation...
-
Problems of analytical determination of journal bearing bush fatigue strength estimates
PublikacjaProblems connected with determination of stress distribution in sliding layer of thinwalled bearing bushes, investigated in bearing fatigue test rigs, have been presented. Using an example of plain bearings tested in the fatigue machine SMOK (built at the Gdask University of Technology) problems with obtaining a convergence of iterative procedure for determining the fatigue strength estimators of bearing alloy surface layer are...
-
Influence of design of hydraulic components on their operation in low ambient temperatures
PublikacjaW artykule przestawiono wpływ konstrukcji zespołów hydraulicznych na ich działanie w niskich temperaturach otoczenia.
-
Experimental Investigation of Prototype Water-Lubricated Compliant Foil Bearings
PublikacjaPraca zawiera wyniki badań doświadczalnych prototypowego łożyska foliowego smarowanego wodą. Łożyska tego typu mogą mieć zastosowanie w węzłach, od których wymaga się ekologicznego środka smarowego, np. pompy wodne czy turbiny wodne. W opracowaniu zademonstrowano wyniki badań trzech prototypowych poprzecznych łożysk foliowych. Opisano napotkane problemy badań oraz wprowadzonych do konstrukcji łożyska zmian, których celem była poprawa...
-
Beeswax And Palmitic Acid Utilization With Heat Pipes For Electronics Cooling
PublikacjaThis paper presents an experimental study of heat pipes supported by phase change materials (PCMs) coated at their adiabatic sections in application for electronics cooling. The PCMs investigated in this research were palmitic acid and beeswax, the latter being considered as a more cost-effective alternative. The study focused on three powers: 20W, 25W, and 30W. The experimental results revealed that the incorporation of palmitic...
-
A role of destructive and non-destructive tests in creep damage Identification
PublikacjaPrzedstawiono wyniki badań mjących zilustrować i określić rolę badań niszczących i nieniszczących w identyfikowaniu degradacji po pełzaniu
-
Influence of Phase Composition on Dielectric Properties of Bismuth-Based Ceramics with Scheelite-Type Structure
PublikacjaGoal of the present research was to study dielectric properties of BiNbO4 ceramics fabricated by solid state reaction route followed with pressureless sintering. The samples were fabricated from the mixture of oxides, viz. Nb2O5 and Bi2O3. Apart from stoichiometric amount an excess of 3%, 5% and 10% by mole of Bi2O3 was used. It was found that an excess amount of Bi2O3 oxide caused formation of Bi5Nb3O15 minor phase in amount of...
-
Dielectric Properties of BiNbO<sub>4</sub>-Based Ceramic-Polymer Composites with 0-3 Connectivity
PublikacjaIn the present study two-phase BiNbO4//PVDF composites with 0-3 connectivity were studied by impedance spectroscopy within the frequency range Δν=100Hz-1MHz at room temperature. Polyvinylidene fluoride (PVDF) acted as a matrix whereas bismuth niobate (BiNbO4) powder acted as a dispersed phase. The volume fraction of the ceramic phase was cV=2, 4, 6, 8, 10, 16 and 20vol%. Analysis of the impedance data registered for composites...
-
High Speed Milling vibration surveillance with optimal spindle speed based on optimal speeds map
PublikacjaThe paper presents the method of the surveillance of the self-excited chatter vibration. At first, the workpiece modal parameters are estimated based on experimental data which leads to verification of computational model. Then, for selected surface points optimal spindle speeds are calculated. By considering sufficient amount of points it is possible to build a map of optimal spindle speeds. Experimental results show that this...
-
Analysis of Rolling Resistance of Tires With Run Flat Insert
PublikacjaRun flat properties are required for tires intended for special applications like military or rescue vehicles. Run-Flat inserts make possible to drive a car or truck, with certain restrictions, also when inflation pressure is very low or non-existing (after tire damage). Rolling resistance of tires rolling the inserts increases considerably in relation to the rolling resistance of properly inflated tires. This paper presents results...
-
Diffusible Hydrogen Control in Flux Cored Arc Welding Process
PublikacjaOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper an experimental...
-
Modal parameters identification with Particle Swarm Optimization
PublikacjaThe paper presents method of the modal parameters identification based on the Particle Swarm Optimization (PSO) algorithm [1]. The basic PSO algorithm is modified in order to achieve fast convergence and low estimation error of identified parameters values. The procedure of identification as well as algorithm modifications are presented and some simple examples for the SISO systems are provided. Results are compared with the results...
-
Road texture influence on tire rolling resistance
PublikacjaTire rolling resistance is one of the most important resistive forces acting on road vehicles. It depends on tire and surface characteristics as well as vehicle operating parameters. This paper deals with the influence of road surface texture on rolling resistance of passenger car tires. Results of road measurements performed on variety of road surfaces are presented.
-
Free convection of water-Al2O3 nanofluid from horizontal porous coated tube
PublikacjaNanofluids are expected to enhance heat transfer in many thermal systems. Present efforts are concentrated on boiling heat transfer of nanofluids, although single phase convection is of key importance in various appliances such as car radiators or heating systems. This paper presents experimental results of heat transfer during free convection of water-Al3O3 nanofluid from horizontal tube covered with metallic porous coating. Contrary...
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublikacjaThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Damage-involved response of two colliding buildings under non-uniform earthquake loading
PublikacjaPounding between insufficiently separated buildings, which may result in considerable damage or may even lead to the total collapse of colliding structures, has been repeatedly observed during earthquakes. Earthquake-induced collisions of buildings has been intensively studied applying various structural models. It was assumed in the analyses, however, that the seismic excitation is identical for all structural supports; whereas,...
-
Generative Process Planning with Reasoning based on Geometrical Product Specification
PublikacjaThe focus of this paper is on computer aided process planning for parts manufacture in systems of definite process capabilities, involving the use of multi-axis machining centers for parts shaping and grinding machines for finishing. It presents in particular a decision making scheme for setup determination as a part of generative process planning. The planning procedurę consists of two stages. The first stage is associated with...
-
Frequency response spectra applied to assess efficiency of the training techniques
PublikacjaThe purpose of the research is to assess the increase of the muscle strength and power. Movement of the human body when the moving one impacts a stationary or moving body is taken under consideration. The waveform produced by an impact is transformed into frequency domain. The acceleration record is transformed as a complex spectrum, by the use of a Discrete Fourier Transformation. In this paper the applications of the discrete...
-
On Software Unit Testing For Improving Security And Performance Of Distributed Applications
PublikacjaPerformance and security are software (SW) application attributes situated on the opposite corners of system design. In the most drastic example the most secure component is the one totally isolated from the outside world, with communication performance reduced to zero level (e.g. disconnected physically from the network, placed inside a Faraday cage to eliminate possible wireless accessibility). On the other hand the most performance-optimized...
-
The analysis of turbine propulsion systems in nuclear submarines
PublikacjaThe article systematises submarines, which are presently in service, according to their propulsion types (both conventional and nuclear), power output, and submersion depth. Contemporary types of propulsion systems installed and used in submarines are discussed. Calculations were performed for the PWR (Pressurized Water Reactor) type nuclear propulsion system and the supercritical turbine propulsion system (supercritical reactor...
-
Carbon dioxide potential reduction using Start-Stop system in a car
PublikacjaOperating fuel consumption increases significantly when the vehicle stops frequently while driving or when the engine is idling during braking. In such cases, the internal combustion engine consumes the fuel but the mechanical energy is not used by the drive system. The amount of fuel that is consumed in this time by the engine can potentially be saved if the car is equipped with a Stop-Start system. Start-Stop system automatically...
-
Fabrication and Study of BiNbO4 Ceramics
PublikacjaAim of the present research was to fabricate and study crystalline structure as well as dielectric properties of BiNbO4 ceramics. In the present study BiNbO4 ceramics was fabricated by solid state reaction from the mixture of simple oxides viz. Bi2O3, and Nb2O5. Stoichiometric mixture of the powders was thermally analyzed so parameters of the thermal treatment were determined. The EDS measurements proved conservation of the chemical...
-
Effect of surface roughness on thermal-hydraulic characteristics of plate heat exchanger
PublikacjaIn the paper the experimental analysis of passive heat transfer intensification in the case of modeled plate heat exchanger is conducted. The plate heat exchanger is chosen for the analysis because this kind of heat exchangers could be prospectively applied in the ORC systems, however other areas or application are equally possible. The experimental setup was assembled at the Department of Energy and Industrial Apparatus of Gdansk...
-
Organic Rankine as bottoming cycle to a combined Brayton and Clausius-Rankine cycle
PublikacjaThis paper presents an enhanced approach, as it will be considered here that the ORC installation could be extra-heated with the bleed steam, a concept presented by the authors. In such way the efficiency of the bottoming cycle can be increased and an amount of electricity generated increases. A thermodynamic analysis and a comparative study of the cycle efficiency for a simplified steam cycle cooperating with ORC cycle will be...
-
The initial selection of parameters for dynamic brake for car engine test dynamometer
PublikacjaThe article presents an analysis of the car engine loads. The aim of the analysis was to determine the parameters of the brake / electric motor on an engine test bad. Analysis of loads on the driving tests concerned on chassis dynamo to simulate them on an engine dynamometer. To check the range of dynamometer shaft angular acceleration inertial mass of a car was reduced on the crankshaft axis. The calculations of maximum shaft...
-
Experimental Study on Pounding between Structures during Damaging Earthquakes
PublikacjaMutual pounding between structures during earthquakes may cause serious structural damage. The aim of this paper is to show the results of a shaking table experimental study focused on pounding between structures in series under several earthquake excitations. The experiments were performed using three tower models with different configurations and different gap distances between them. In the first stage of the study, one rigid...
-
Enhancing the Seismic Resistance of Columns by GFRP Confinement Using Flexible Adhesive-Experimental Study
PublikacjaIn this paper, the results of two experiments, focused on testing the effectiveness of a method of enhancing the seismic (dynamic) resistance of masonry columns with the use of flexible polymer adhesive, are shown. The first experiment was devoted to investigate the damping properties of a polymer working between two stiff layers, whereas the aim of the second one was to verify if the identified damping properties of the polymer...
-
Highly Oriented Zirconium Nitride and Oxynitride Coatings Deposited via High‐Power Impulse Magnetron Sputtering: Crystal‐Facet‐Driven Corrosion Behavior in Domestic Wastewater
PublikacjaHerein, highly crystalline ZrxNy and ZrxNyOz coatings are achieved by the deposition via high‐power impulse magnetron sputtering. Various N2 and N2/O2 gas mixtures with argon are investigated. The chemical composition and, as a result, mechanical properties of the deposited layer can be tailored along with morphological and crystallographic structural changes. The corrosion resistance behavior is studied by potentiodynamic measurements...
-
Pounding between Inelastic Three-Storey Buildings under Seismic Excitations
PublikacjaStructural interactions between adjacent, insufficiently separated buildings have been repeatedly observed during damaging ground motions. This phenomenon, known as the structural pounding, may result in substantial damage or even total collapse of structures. The aim of the present paper is to show the results of the nonlinear numerical analysis focused on pounding between inelastic three-storey buildings under seismic excitations....
-
Cobalt-/Copper-Containing Perovskites in Oxygen Evolution and Reduction Reactions
Publikacja -
Energy-based fatigue failure characteristics of materials under random bending loading in elastic-plastic range
Publikacja -
Quasistatic and fatigue behavior of an AISI H13 steel obtained by additive manufacturing and conventional method
Publikacja -
Quasistatic and fatigue behavior of an AISI H13 steel obtained by additive manufacturing and conventional method
PublikacjaThis work aims to compare the mechanical behavior of an AISI H13 steel obtained by additive manufacturing with that obtained by conventional manufacturing methods. The average values of the ultimate tensile strength (UTS) and ductility obtained for the specimens produced by the conventional method were equal to 658 MPa and 18%, respectively, which compares with 503 MPa and 0.75% registered for the selective laser melting (SLM)...
-
Experimental investigations and damage growth modeling of EN‐AW 2024 aluminum alloy under LCF loading accounting creep pre‐deformation
PublikacjaThis article presents the results of experimental tests of creep rupture and of low-cycle fatigue (LCF) of EN-AW 2024 aluminum alloy devoid of damage and having preliminary damage. The preliminary damage was dealt in the process of creep at elevated temperature 100C, 200C, and 300C until achievement of two different strain values at each temperature. Samples with preliminary damage were subjected to fatigue tests at room temperature....
-
Temperature distribution in laser-clad multi-layers
Publikacja