Wyszukiwarka
Wyniki wyszukiwania dla: TURBINE DESIGN
-
NUMERICAL SIMULATIONS OF GAP FLOW ABOVE ROTATING DISK
PublikacjaA rotating disk can be considered a basic configuration for the investigati ons of the impact of various conditions on the flow through the clearance between the s hrouded turbine blade and the casing. Numerical calculations using Fine/Turbo Numeca were conducted to examine the influence of the rotational velocity and the pressure differ ence across the disk on the flow conditions, especially the mass flow through the clearance....
-
Experimental investigations and simulations of the microturbine unit with permanent magnet generator
PublikacjaIn dispersed power generation, low power devices are used for local combined generating of heat end electric power. There are developing concepts of micropower plants with electric generators driven by steam or gas microturbines. The paper presents the results of an experimental investigations of the microturbine set consists of the turbine with partial admission, permanent magnet generator and three phase AC-to-DC rectifier. The...
-
Double-stage ORC system based on various temperature waste heat sources of the negative CO2 power plant
PublikacjaAnalysed is the modification of the thermodynamic cycle with the negative CO2 power plant concept by its combination with the organic Rankine cycle. The analysed power plant operates on a gas produced from the gasification of sewage sludge. The negative emission term comes from the aggregated CO2 balance resulting from the capture of the CO2, while the sewage sludge is one of the inevitable environmental sources of CO2 to be avoided....
-
COMPARISON OF TWO MODELS OF CONDENSATION
PublikacjaIn the low-pressure part of steam turbine, the state path usually crosses the saturation line in penultimate stages. At least last two stages of this part of turbines operate in two –phase region. The liquid phase in this region in mainly created in the process of homogeneous and heterogeneous condensation. Several observations confirm however, that condensation often occurs earlier than it is predicted by theory i.e. before the...
-
Comparative study of operation of condensing and traditional boilers equipped with ORC module for electricity generation
PublikacjaThe study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler. In the case of a conventional boiler there is noted a greater fuel consumption and the greater power generated than in the case of the unit with the condensing boiler. Postulated is the indicator in the form of a ratio of turbine power to the mass flow rate of fuel, which in turn gives...
-
The Latest Advances in Wireless Communication in Aviation, Wind Turbines and Bridges
PublikacjaPresent-day technologies used in SHM (Structural Health Monitoring) systems in many implementations are based on wireless sensor networks (WSN). In the context of the continuous development of these systems, the costs of the elements that form the monitoring system are decreasing. In this situation, the challenge is to select the optimal number of sensors and the network architecture, depending on the wireless system’s other parameters...
-
Dependence of Power Characteristics on Savonius Rotor Segmentation
PublikacjaSavonius rotors are large and heavy because they use drag force for propulsion. This leads to a larger investment in comparison to horizontal axis wind turbine (HAWT) rotors using lift forces. A simple construction of the Savonius rotor is preferred to reduce the production effort. Therefore, it is proposed here to use single-segment rotors of high elongation. Nevertheless, this rotor type must be compared with a multi-segment...
-
Alternative diagnostic method applied on marine diesel engines having limited monitoring susceptibility
PublikacjaThe paper presents a method of technical state evaluation of working spaces of a marine diesel engine at the limited control susceptibility. The method foresees making a diagnosis of the engine's working spaces on the basis of measurements of the exhaust gas pressure in the channels connecting engine cylinders with the turbocharger's turbine. Diagnostic measurements are carried out at representative (comparative) steady loads depending...
-
Alternative diagnostic method applied on marine diesel engines having limited monitoring susceptibility
PublikacjaThe paper presents a method of technical state evaluation of working spaces of a marine diesel engine at the limited control susceptibility. The method foresees making a diagnosis of the engine's working spaces on the basis of measurements of the exhaust gas pressure in the channels connecting engine cylinders with the turbocharger's turbine. Diagnostic measurements are carried out at representative (comparative) steady loads depending...
-
A Preliminary Study and Analysis of Tidal Stream Generators
PublikacjaFor a sustainable future, tidal energy can play a vital role. Tidal energy relies on the gravitational pull of the Moon and the Sun along with the centrifugal forces created by the Earth. Tidal barrage uses the potential energy from the tide and has been very successful in electricity production. With the help of a turbine, kinetic energy can also be harnessed from tidal currents to generate electricity. However, it is not economically...
-
Analysing the potential for application of the phase shift method in endoscopic examination of marine engines
PublikacjaThe article presents theoretical principles of image processing in digital endoscopy which makes use of a miniaturised spectral scanner “PhaseProbe” designed by General Inspection Technologies LP, the producer of the measuring videoendoscope Everest XLG3. The technology of optoelectronic 3D mapping of the examined surface, which consists in measuring the phase shift between the emitted and reflected light waves, is briefly described....
-
Proceedings of the 9th International Conference on Structural Dynamics, EURODYN 2014
PublikacjaSince offshore wind turbine supporting structures are subjected to dynamic environments with time-varying loading conditions, it is important to model their dynamic behavior and validate these models by means of vibrational experiments. In this paper assessment of dynamical state of the structure is investigated by means of both: numerical modeling, and experimental modal analysis. In experimental modal analysis, capturing the...
-
Comparative study of operation of condensing and traditional boilers equipped with the ORC module for electricity generation
PublikacjaCondensing technology applied to boilers is to make full use of thermal energy contained in the fuel. That means that additionaly the heat from condensation of exhaust gases can be used for the purposes of heating the domestic hot water and to cover the demand for central heating. The study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler....
-
Comparative study of a combined heat and power plant retrofitted by CO2 capture during the combustion of syngas from sewage sludge gasification versus zero-emission combustion of hydrogen produced using renewables
PublikacjaWith ecological requirements aimed at limiting the production of CO2, it is necessary to produce all, or most of the energy from RES. During the transformation process, ecological and highly efficient combustion power plants will be needed. The classic cycle of combined heat and power (CCGT) with green improvements will continue to be one of the most suitable technologies for this task. This article presents the modernization of...
-
The use of liquid crystal thermography TLC and particle image velocimetry PIV in selected technical applications
PublikacjaNowadays, the energy cost is very high and this problem is carried out to seek techniques for improvement of the aerothermal and thermal (heat flow) systems performances in different technical applications. The transient and steady-state techniques with liquid crystals for the surface temperature and heat transfer coefficient or Nusselt number distribution measurements have been developed. The flow pattern produced by transverse...
-
Thermodynamic Analysis of Negative CO2 Emission Power Plant Using Aspen Plus, Aspen Hysys, and Ebsilon Software
PublikacjaAbstract: The article presents results of thermodynamic analysis using a zero-dimensional mathematical models of a negative CO2 emission power plant. The developed cycle of a negative CO2 emission power plant allows the production of electricity using gasified sewage sludge as a main fuel. The negative emission can be achieved by the use this type of fuel which is already a “zeroemissive” energy source. Together with carbon capture...
-
Induction Generator with Direct Control and a Limited Number of Measurements on the Side of the Converter Connected to the Power Grid
PublikacjaThe article presents an induction generator connected to the power grid using the AC/DC/AC converter and LCL coupling filter. Three-level inverters were used in the converter, both from the generator side and the power grid side. The algorithm realizing Pulse Width Modulation (PWM) in inverters has been simplified to the maximum. Control of the induction generator was based on the Direct Field-Oriented Control (DFOC) method. At...
-
Comparison analysis of selected nuclear power plants supplied with helium from high-temperature gas-cooled reactor
PublikacjaThe article presents results of efficiency calculations for two 560 MW nuclear cycles with high-temperature gas-cooled reactor (HTGR). An assumption was made that systems of this type can be used in so-called marine nuclear power plants. The first analysed system is the nuclear steam power plant. For the steam cycle, the efficiency calculations were performed with the code DIAGAR, which is dedicated for analysing this type of systems....
-
Study of the Influence of Heat Convection Coefficient on Predicted Performance of a Large Tilting-Pad Thrust Bearing
PublikacjaPart of the heat generated by the shearing of the lubricating film during operation of a hydrodynamic bearing is transferred to the bearing components. In the case of the pad, which is usually fully submerged in the lubricating oil, heat is further transferred at the pad free walls to the oil by convection. This mechanism causes a thermal gradient in a pad and, consequently, its thermal deflection. In large hydrodynamic thrust...
-
Uncertainty Quantification in Experimental Structural Dynamics Identification of Composite Material Structures
PublikacjaComposite materials are widely used in manufacture of aerospace and wind energy structural components. These load carrying structures are subjected to dynamic time-varying loading conditions. Robust structural dynamics identification procedure impose tight constraints on the quality of modal models estimates obtained from vibration experiments. Modal testing results are influenced by numerous factors introducing uncertainty to...
-
Voltage Control of a Stand-Alone Multiphase Doubly Fed Induction Generator
PublikacjaThis article presents a multiphase doubly fed induction generator (MDFIG) with a dedicated and unique control algorithm in a stand-alone wind energy conversion system. The algorithm has been developed and elaborated in the case of different emergency modes. Compared with the traditional double-fed induction generator, the MDFIG has increased reliability, reduced current level per phase, and low rotor harmonic currents. The control...
-
Applying response surface method to optimize the performance of a divergent-chimney solar power plant
PublikacjaOne of the effective tools to generate electricity from solar energy is Divergent-chimney solar power plant (DSPP). Divergent and cylindrical chimneys of solar power plants have different performances considering turbine pressure drop ratio (ft). For the first time, the divergent angle (DA) and solar radiation (SR) interaction effects on 〖ft〗_opt are discussed through applying the Computational Fluid Dynamics (CFD) and Response...
-
Utilisation of waste heat from the power plant by use of the ORC aided with bleed steam and extra source of heat
PublikacjaUtilization of waste heat recovered from the exhaust gases of the power generation unit by means of ORC (organic Rankine cycles) installation is considered. The waste heat is available in the form of a stream of hot water having temperature of 90 stC in the amount of 200 MWt. To increase evaporation temperaturę of ORC working fluid the heat of steam from the extraction points from the low-pressure part of steam turbine is used....
-
Possibility to use engine compression ignition engines in floating power plants marine
PublikacjaCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. The engines can be used in power industry for electricity generation in a simple or combined steam turbine system in combined heat and power plants. The leading engine in such an arrangement is an internal-combustion piston engine. The main propulsion engines are used in large piston internal-combustion engines...
-
Review of Methods for Diagnosing the Degradation Process in Power Units Cooperating with Renewable Energy Sources Using Artificial Intelligence
PublikacjaThis work is based on a literature review (191). It mainly refers to two diagnostic methods based on artificial intelligence. This review presents new possibilities for using genetic algorithms (GAs) for diagnostic purposes in power plants transitioning to cooperation with renewable energy sources (RESs). The genetic method is rarely used directly in the modeling of thermal-flow analysis. However, this assignment proves that the...
-
Exhaust gas temperature measurements in diagnostics of turbocharged marine internal combustion engines. Part I. Standard measurements.
PublikacjaThe article discusses the problem of diagnostic informativeness of exhaust gas temperature measurements in turbocharged marine internal combustion engines. Theoretical principles of the process of exhaust gas flow in turbocharger inlet channels are analysed in its dynamic and energetic aspects. Diagnostic parameters are defined which enable to formulate general evaluation of technical condition of the engine based on standard...
-
Modeling by finite element methods of impact of erosion on frequency of normal modes of L-0 blade
PublikacjaAfter some time of exploitation steam turbine rotors blades in energetic industry they are being eroded and also their frequency of normal modes is changed. Those changes can cause to unwanted shift of blades normal mode frequencies. It is necessary to find quick method of rating changes of frequency in connection of mass loss due erosion. The evaluation of this dependence was made by finite element modeling method using HyperWorks...
-
“Shadow” vs. “Phase 3D” method within endoscopic examinations of marine engines
PublikacjaA visual investigation of surfaces creating internal, working spaces of marine combustion engines by means of specialized view-finders so called endoscopes is at present almost a basic method of technical diag-nostics. The surface structure of constructional material is visible during investigations like through the magnifying glass (usually with a precisely determined magnification), which makes possible a detection, recognition...
-
Power System Stabilizer as a Part of a Generator MPC Adaptive Predictive Control System
PublikacjaIn this paper, a model predictive controller based on a generator model for prediction purposes is proposed to replace a standard generator controller with a stabilizer of a power system. Such a local controller utilizes an input-output model of the system taking into consideration not only a generator voltage Ug but also an additional, auxiliary signal (e.g., α, Pg, or ωg). This additional piece of information allows for taking...
-
Comprehensive thermodynamic analysis of steam storage in a steam cycle in a different regime of work: A zero-dimensional and three-dimensional approach
PublikacjaDue to the current trends aiming to reduce carbon dioxide emissions by increasing the use of renewable energy sources, changes are required in the operation of coal-fired steam units. The unstable nature of renewable energy sources, depending on weather conditions, means that the amount of energy produced varies and is not always in line with peak demand. To ensure the security and stability of energy supplies in the energy system,...
-
Thermodynamic analysis of the Compressed Air Energy Storage system coupled with the Underground Thermal Energy Storage
PublikacjaImprovement of flexibility is one of the key challenges for the transformation of the Polish Power System aiming at a high share of renewable energy in electricity generation. Flexible and dispatchable power plants will contribute to this ongoing transformation process as they compensate for fluctuations in electricity generation from renewable energy sources such as wind and photovoltaics. In this context, CAES storage tanks are...
-
Analysis of Organic Rankine Cycle efficiency and vapor generator heat transfer surface in function of the reduced pressure
PublikacjaIn the paper presented is analysis of the influence of reduced pressure on efficiency and heat transfer area of vapor generator of Organic Rankine Cycle (ORC) in case of subcritical and supercritical parameters of operation. Compared are two cases of subcritical and supercritical ORC featuring a similar arrangement of heat source supply and heat removal, that is featuring the same temperatures of working fluid before the turbine,...
-
Fault detection in measuring systems of power plants
PublikacjaThis paper describes possibility of forming diagnostic relations based on application of the artifical neural networks (ANNs), intended for the identifying of degradation of measuring instruments used in developed power systems. As an example a steam turbine high-power plant was used. And, simulative calculations were applied to forming diagnostic neural relations. Both degradation of the measuring instruments and simultaneously...
-
Thermodynamic, ecological, and economic analysis of negative CO2 emission power plant using gasified sewage sludge
PublikacjaCurrently, sewage sludge is considered as a biomass, according to the Polish act on renewable energy sources from 20th of February 2015 and its novel version from 19th of July 2019. Possibility to utilize sewage sludge in gasification process is an additional advantage of the negative CO2 emissions power plant (nCO2PP). The work presents results of thermodynamic, ecological, and economical analysis using a zero-dimensional mathematical...
-
A novel concept of negative CO2 emission power plant for utilization of sewage sludge
PublikacjaCarbon Capture and Storage (CSS) technology is considered an important “bridge technology”, allowing effective abatement of CO2 emissions for power units using fossil fuels. However, if biomass is used in a power plant, equipped with CCS system, negative CO2 emissions can be achieved. In practice, wide development of such technologies would enable not only reduction of CO2 emissions, but also reversal of the harm done so far. In...
-
An adaptive-noise Augmented Kalman Filter approach for input-state estimation in structural dynamics
PublikacjaThe establishment of a Digital Twin of an operating engineered system can increase the potency of Structural Health Monitoring (SHM) tools, which are then bestowed with enhanced predictive capabilities. This is particularly relevant for wind energy infrastructures, where the definition of remaining useful life is a main driver for assessing the efficacy of these systems. In order to ensure a proper representation of the physical...