Wyniki wyszukiwania dla: CALCULATION OF THERMAL STRESSES IN ASPHALT
-
Nowa metoda obliczania rozpływu prądów zwarciowych w przewodach odgromowych linii wysokiego napięcia
PublikacjaReferat przedstawia nowatorską metodę obliczania wartości prądów płynących w przewodach odgromowych w czasie zwarć, pozwalającą na dobór przewodów odgromowych pod względem wytrzymałości cieplnej. Proponowana metoda charakteryzuje się większą dokładnością i większą uniwersalnością niż powszechnie stosowane metody, pozwalając tym samym na dobór przewodów odgromowych z mniejszym ryzykiem niepewności. Prezentowana metoda obliczeniowa...
-
Modelling of the Baumann turbine stage operation Part II. Free and kinetic vibrations
PublikacjaIn this paper has been presented a methodology of validation a novel mathematical model dedicated to evaluation and prediction of material degradation and demage of steam turbine elements such as blades, valves and pipes due to three mechanisms: stress-corosion, high-temperature creep and low-cyclic fatigue. The validation concept is based on an experimental setup manufactured in the Laboratory of Faculty of Mechanical and Power...
-
Heat transfer characteristics of hybrid microjet – Microchannel cooling module
PublikacjaThe paper presents experimental investigation of heat transfer intensification in a microjet–microchannel cooling module. Applied technology takes benefits from two very attractive heat removal techniques. When jets are impinging on the surface, they have a very high kinetic energy at the stagnation point, also in microchannels boundary layer is very thin allowing to obtain very high heat fluxes. Main objective of this paper was...
-
Heat transfer characteristics of hybrid microjet -microchannel cooling module
PublikacjaThe paper presents the experimental investigation of heat transfer intensification in a microjet- microchannel cooling module. Applied technology takes benefits from two very attractive heat removal techniques. When jets are impinging on the surface, they have a very high kinetic energy at the stagnation point, also in microchannels boundary layer is very thin allowing to obtain very high heat fluxes. Main objective of this paper...
-
Elementary analysis and energetic potential of the municipal sewage sludges from the Gdańsk and Kościerzyna WWTPs
PublikacjaThis paper aims to present municipal sewage sludge (MSS) elementary analysis and energetic potential based on measurement of heat of combustion (higher heating value HHV) and calculation of calorific values (lower heating value LHV). The analysis takes into the consideration water content in sewage sludge, at different utilization stages, in wastewater treatment plants in Gdańsk Wschód and Kościerzyna – Pomeranian Voivodeship....
-
Local Nusselt number evaluation in the case of jet impingement
PublikacjaJet impingement still is one of demanding cases regarding computational fluid dynamics, due to its highly turbulent behaviour, with occurrence of turbulent-laminar transition. Even recently developed methods exhibit some drawbacks – RANS based simulations lack accuracy, LES and DNS based ones require too much computational time. Hybrid methods also exist, but their development and validation is in progress. Nevertheless, CFD application...
-
Experimental tuning of AuAg nanoalloy plasmon resonances assisted by machine learning method
PublikacjaPlasmonic nanostructures based on AuAg nanoalloys were fabricated by thermal annealing of metallic films in an argon atmosphere. The nanoalloys were chosen because they can extend the wavelength range in which plasmon resonance occurs and thus allow the design of plasmonic platforms with the desired parameters. The influence of initial fabrication parameters and experimental conditions on the formation of nanostructures was investigated....
-
COMPARISON OF HEAT TRANSFER CHARACTERISTICS IN SURFACE COOLING WITH BOILING MICROJETS OF WATER, ETHANOL AND HFE7100
PublikacjaThe basis of microjet technology is to produce laminar jets which when impinging the surface have a very high kinetic energy at the stagnation point. Boundary layer is not formed in those conditions, while the area of film cooling has a very high turbulence resulting from a very high heat transfer coefficient. Applied technology of jet production can result with the size of jets ranging from 20 to 500μm in breadth and 20 to 100μm...
-
Pressure effects on the superconductivity of the HfPd2Al Heusler compound: Experimental and theoretical study
PublikacjaPolycrystalline HfPd2Al has been synthesized using the arc-melting method and studied under ambient-pressure conditions by x-ray diffraction from room temperature up to 450 °C. High-pressure x-ray diffraction up to 23 GPa was also performed using Diacell-type membrane diamond anvil cells. The estimated linear thermal expansion coefficient was found to be α=1.40(3)×10−5K−1, and the bulk modulus derived from the fit to the third-order...
-
Physical properties of homogeneous TiO2 films prepared by high power impulse magnetron sputtering as a function of crystallographic phase and nanostructure
PublikacjaOptical, photo-electrochemical, crystallographic and morphological properties of TiO2 thin films prepared by high power impulse magnetron sputtering at low substrate temperatures (<65 ◦C) without post-deposition thermal annealing are studied. The film composition-anatase, rutile or amorphous TiO2-is adjusted by the pressure (p ∼ 0.75-15 Pa) in the deposition chamber. The different crystallographic phases were determined with grazing...
-
Real-Time Facial Features Detection from Low Resolution Thermal Images with Deep Classification Models
PublikacjaDeep networks have already shown a spectacular success for object classification and detection for various applications from everyday use cases to advanced medical problems. The main advantage of the classification models over the detection models is less time and effort needed for dataset preparation, because classification networks do not require bounding box annotations, but labels at the image level only. Yet, after passing...
-
Modeling of Passive and Forced Convection Heat Transfer in Channels with Rib Turbulators
PublikacjaThe main goal of the research presented in this paper was the experimental and numerical analysis of heat enhancement and aerodynamic phenomena during air flow in a channel equipped with flow turbulators in the form of properly configured ribs. The use of ribs intensifies the heat transfer and at the same time increases not only the flow resistance but also the energy costs. Therefore, designing modern heat exchangers with optimal...