Wyszukiwarka
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: TYRE LABELLING PROCEDURE
-
ISO test track influence on the EU tyre label noise value
PublikacjaIn 2009, the European Union (EU) introduced a directive governing the labelling of tyres, which underwent revision in 2020. This labelling system encompasses three key parameters related to tyre performance: wet grip (safety), rolling resistance (energy consumption), and external rolling noise (environmental impact). These label values serve as crucial information for customers seeking to purchase replacement tyres for their vehicles....
-
INFLUENCE OF MEASURING CONDITIONS ON TYRE/ROAD NOISE
PublikacjaA decisive factor for the development of tyres and road surfaces is the ability to conduct representative and reproducible measurements of selected characteristics related to the interaction of tyres and road surfaces. In terms of tyre/road noise measurements in Europe two methods described in ISO/FDIS 11819-2 and ECE Regulation No.117 are used. The latter is compulsory for assigning the tyre noise labels. The methodologies differ...
-
Tyre/road noise measurements on ISO tracks using the modified CPX method
PublikacjaTyre rolling noise test method specified in the UNECE Regulation 117 is directly used in the Tyre Labelling Directive. Noise level specified on EU Tyre Label of each new tyre available on the European market was determined based on vehicle coast-by noise measurements performed on the standard reference road surface proscribed in the ISO 10844:2014. Available data from investigations by the vehicle and tyre industry and results...
-
Representativity of ISO test track surface based on controlled pass-by measurements
PublikacjaWithin the Polish-Norwegian research project ELANORE, a limited Round Robin Test has been performed on four ISO tracks in Northern Europe. The basic objective of the project is to improve the EU directive on labelling of tyres for noise and rolling resistance. This directive is based on the measurement procedures proscribed in the UNECE Reg.117. Measurements on 3 ISO tracks were performed in 2021 and presented at InterNoise 2022....
-
The EU Tyre Noise Label: The problem with measuring the noise level of only a few of all tyre variants
PublikacjaThe STEER project, described in another Inter-Noise 2022 paper, has evaluated the performance of the noise label of the European tyre label. The major finding was that uncertainties of the tyre/road noise measurements were higher than should be accepted. One of the worst uncertainty sources was found to be the common practice to measure only some tyres of all sizes or variants within a tyre line, to save money. Generally, only...
-
Temperature influence on tyre/road noise frequency spectra
PublikacjaThe correction for temperature effect on measured tyre/road noise is very important as it may be one of the main sources of errors in measurement results due to substantial influence of this parameter on obtained values. The latest version of the Technical Specification ISO/CD TS 13471-1 about Temperature Corrections contains a proposal of correction procedure for normalizing measured noise levels to a reference air temperature...
-
INFLUENCE OF TEMPERATURE ON THE TYRE ROLLING RESISTANCE
PublikacjaTemperature is a very important factor controlling rolling resistance of road vehicle tyres. There are at least three different temperatures that may be considered as important factors controlling thermal conditions of the rolling tyre. The most common measure of the thermal conditions during tyre rolling is ambient air temperature. The other two are: pavement temperature and “tyre” temperature. Tyre temperature is the most difficult...
-
Road texture influence on tyre rolling resistance
PublikacjaTyre performance, one of the critical factors for vehicle users, is strongly related to theroad surface characteristics, most notably to the pavement texture. Phenomena that occur at the tyre/road interface affect tyre friction (skid resistance), rolling resistance, tyre wear and tyre/road noise. This article deals with relationship between surface texture and rolling resistance of light and heavy vehicle tyres. Mean profile depth...
-
INFLUENCE OF TEST CONDITIONS ON TYRE/ROAD NOISE MEASURED BY THE DRUM METHOD
PublikacjaTyre/road noise is one of the most important environmental problems related to road traffic. Nowadays a few standard procedures of tyre/road noise measurements are in use. Unfortunately, measurement conditions specified within relevant standards are very different. For example, procedure described in ISO 11819-2 used for pavement investigations requires tyre load of 3200 N and capped inflation pressure of 200 kPa. At the same time...
-
Modernization of the Trailer for Tyre/Road Rolling Resistance Measurements
PublikacjaIn the article the ways of defining tyre rolling resistance are presented. The advantages of the laboratory tests of tyre/road rolling resistance and the advantages and disadvantages of on the road tyre/road rolling resistance tests are described. The description of the special trailer used for tyre/road rolling resistance measurements designed and constructed in the Faculty of Mechanical Engineering at Gdansk University of Technology,...
-
The influence of road surface unevenness on tyre rolling resistance
PublikacjaThe geometric characteristics of road surface substantially affect the interaction between tyre and road. Depending on pavement texture wavelength, the texture chiefly affects tyre/road friction, rolling resistance, interior and exterior noise, tyre wear, and ride comfort. The article presents results of investigations on the influence of road surface unevenness on the rolling resistance of passenger car and truck tyres. The tests...
-
Comparison of road and laboratory measurements of tyre/road noise
PublikacjaTyre/road noise is one of the major environmental problems related to road traffic. There are several measuring methods of tyre/road noise that may be carried out on the road (for example Coast-down and Close Proximity Method) or in the laboratory (Drum Method). Road measurements are preferred for evaluations of pavement properties while laboratory methods are mostly used to evaluate tyres. One of the biggest problems associated...
-
Temperature influence on tyre/road noise of selected tyres
PublikacjaAir and road temperatures substantially affect road vehicle noise emission. The temperature influence on tyre/road noise depends mainly on tyre-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tyres. The correction procedures for temperature effect are still under consideration and preparation. Tyre/road noise measurements using CPX method were performed...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublikacjaThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Tyre rolling resistance and its influence on fuel consumption
PublikacjaRolling resistance of tyres is one of the major resistive forces acting on any wheeled vehicle. Unfortunately, it is also one of the forces very difficult to measure. It is estimated that in certain traffic conditions (like for example constant speed driving with slow or moderate speed) so called Rolling Resistance Impact Factor may be as high as 0.3. This means that reduction of rolling resistance by 50% would lead to 15% of energy...
-
Validation of a sampling procedure
PublikacjaEach step of the analytical procedure influences the final results in a significant way. In the majority of cases the analytical procedure encompasses sampling because the analysis of the entire object (material) is usually not possible. Thus it is necessary to include the uncertainty related to sampling procedure in the uncertainty budget calculations. This paper describes two basic ways of estimating the sampling uncertainty,...
-
Tyre/road noise reduction by a poroelastic road surface
PublikacjaLow noise road surfaces of existing types may in favourable cases and in new conditions provide up to 7 dB of noise reduction. For higher noise reductions, innovative solutions must be sought. Poroelastic road surfaces (PERS) may be such a solution, which currently is studied in the EU project PERSUADE. This paper presents results of trials with a PERS version prefabricated by one of the project partners. Tests were made in a laboratory...
-
Rolling resistance and tyre/road noise on rubberised asphalt pavement in Poland
PublikacjaThe paper presents results of tyre/road noise and rolling resistance measurements performed on stone mastics asphalt (SMA) that contains rubberised asphalt, developed and produced by a refinery in Poland. Bituminous binder was modified with polymer and addition of crumb rubber. The first observations of asphalt mixture with the new kind of modified bitumen used on the field section are presented. Rolling resistance of passenger...
-
The effect of tyre rubber grinding method on the rubber-asphalt binder properties
PublikacjaRubber products, especially those used in the automotive industry, are responsible for a significant amount of waste, mainly in the form of worn tyres. One way to recycle tyres is to use them as an asphalt binder modifier. The properties of rubber-asphalt binders vary greatly depending on the morphology of the ground tyre rubber (GTR) grains and the type of tyre to be recycled (car/truck). The paper presents the results of research...
-
INFLUENCE OF LOAD AND INFLATION PRESSURE ON THE TYRE ROLLING RESISTANCE
PublikacjaTyre load and inflation pressure are important factors controlling rolling resistance of road vehicles. The article presents results obtained in the Technical University of Gdańsk during laboratory and road measurements of different car tyres rolling on different pavements. The knowledge of rolling resistance characteristics is important for modelling car dynamics as well as fuel consumption. It is also necessary to establish proper...
-
A new tool for the evaluation of the analytical procedure: Green Analytical Procedure Index
PublikacjaA new means for assessing analytical protocols relating to green analytical chemistry attributes has been developed. The new tool, called GAPI (Green Analytical Procedure Index), evaluates the green character of an entire analytical methodology, from sample collection to final determination, and was created using such tools as the National Environmental Methods Index (NEMI) or Analytical Eco-Scale to provide not only general but...
-
Relieving the Measuring System of the Trailer for Tyre/Road Rolling Resistance Measurements from the Inertia Force
PublikacjaIn the article the principle of measuring of tyre/road rolling resistance tyres in road conditions applied in a special measuring trailer is presented. This trailer was built in Faculty of Mechanical Engineering at Gdansk University of Technology. The construction of two special devices used in this trailer was discussed. These devices eliminate the influence of some chosen confounding measurements factors such as: the inertia...
-
Introduction in to tyre simulations
PublikacjaW artykule przedstawiono wyniki symulacji komputerowej zachowania się opony w czasie badania jej oporów toczenia w oparciu o program LMS Virtual Lab. Przedstawiono także wnioski wynikające z przeprowadzonej symulacji.
-
Pavement ageing influence on tyre/road noise
PublikacjaRoad surface should be constructed in a way that ensures safe and comfortable traffic conditions, not only when it is newly paved but also during its entire lifetime. An important factor in the asphalt mixture design process is also the expected pavement durability and stability of pavement properties over time. In many countries, road surface starts to play a significant role in traffic noise reduction actions. Selecting a particular...
-
Method of estimating the rolling resistance coefficient of vehicle tyre using the roller dynamometer
PublikacjaThe tendency in the past few years has been to introduce tyres with lower rolling resistance coefficients to the market. This paper presents a mathematical method for determining the rolling resistance coefficients variation depending on the speed. The method uses power balance which results from automobile dynamics while rolling on chassis dynamometer. The rolling resistance coefficients of tyres obtained through ‘drum test method’,...
-
Temperature Measurements at Tyre Tread Rubber on Sandpaper Oscillatory Sliding Contacts Using Acicular Grindable Thermocouples
PublikacjaThe tribological performance of tyre–road contacts depends crucially on the contact temperature. This study investigates the reliability and accuracy of acicular grindable thermocouples possessing an original needle-shaped wearable part as applied to measuring temperature at the oscillatory sliding contact between a rubber tyre tread sample and a sandpaper. A linear oscillatory tribometer is used to imitate the sliding phase of...
-
Tyre/road noise of passenger car tyres, including tyres for electric vehicles - road measurements
PublikacjaThe paper presents the results from CPX measurements of tyre/road noise performed for selected passenger car tyres, including the tyres especially designed for electric vehicles. The tyres have been measured when rolling on several typical road surfaces in Norway and in Poland. In addition, the tyres have been measured on some very low noise road surfaces, such as a the poroelastic road surface (PERS). The measurement results...
-
Efficiency and proportions of waste tyre pyrolysis products depending on the reactor type—A review
PublikacjaThis article discusses the current use of different pyrolytic reactors, their constructions and operating principles regarding the yields of main products of waste tyre pyrolytic recycling. Whether one makes a larger or smaller profit, or even a loss due to a surcharge being levied on waste tyre recycling, depends on the sale of the pyrolysis products (gas, char, oil), the proportions and market prices of which differ. The cheapest...
-
Tyre dynamic radius determination
PublikacjaW artykule opisano stanowisko wykorzystywane do badania oporu toczenia opon samochodowych znajdujące się w Katedrze Konstrukcji Maszyn i Pojazdów Wydziału Mechanicznego Politechniki Gdańskiej. Przedstawiono wyniki badań promienia dynamicznego opony Michelin 165/80R13 83T z bieżnikiem CLASSIC przeprowadzone z wykorzystaniem tego stanowiska na nawierzchni Safety Walk 80. Badania przeprowadzono zmieniając: prędkość jazdy, obciążenie...
-
Tyre/road noise measurements on ISO tracks according to the UNECE Regulation 117
PublikacjaWithin the Polish-Norwegian research project ELANORE, a limited Round Robin Test has been performed on 3 ISO tracks in Northern Europe. The basic objective of the project is to improve the EU directive on labelling of tyres for noise and rolling resistance, and this directive is based on the measurement procedures defined in the UN ECE Reg.117. The same test car, test tyres and measurement equipment as well as personnel were used...
-
Justyna Płotka-Wasylka dr hab. inż.
OsobyUrodziła się w Słupsku (24.03.1986).W 2005 roku ukończyła I Liceum Ogólnokształcące im. Jana II Sobieskiego w Wejherowie i rozpoczęła studia na Wydziale Chemicznym Politechniki Gdańskiej. Po ich ukończeniu w 2010 rozpoczęła pracę naukową na tej uczelni, uzyskując w 2014 roku stopień doktora nauk chemicznych. Tematem jej rozprawy doktorskiej, wykonywanej pod kierunkiem prof. Marka Biziuka oraz dr Caluma Morrisona (Uniwersytet w...
-
FTIR spectroscopic and thermogravimetric characterization of ground tyre rubber devulcanized by microwave treatment
PublikacjaIn this work, the phenomena involved in the microwave devulcanization of ground tyre rubber (GTR) were investigated. Three types of GTR with different content of organic compounds (elastomers, plasticizers, etc.), carbon black and ash have been studied. The chemical structure of GTR before and after a microwave devulcanization process was analyzed by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA)...
-
Tyre/road noise. Reference book.
PublikacjaKsiążka przedstawia zagadnienia związane z hałasem opon samochodowych poruszających się po nawierzchniach drogowych. Zawiera rozdziały poświęcone budowie opon, budowie nawierzchni drogowych, akustyce, mechanizmom generowania hałasu, wpływie czynników eksploatacyjnych i konstrukcyjnych na hałas opon, metodom pomiarowym, modelowaniu, metodom ograniczania hałasu opon, zagadnieniom prawnym i normalizacyjnym. Jest kompletnym przewodnikiem...
-
Chemometrics approaches to green analytical chemistry procedure development
PublikacjaChemometric tools are widely used in analytical chemistry for the reduction of data dimensionality, grouping of variables and processing of analytical signals. They have also the potential to be applied in analytical procedure development with the aim of minimizing the procedure’s environmental impact. The design of experiment gives the possibility to obtain much better information on the system response than in case of “changing...
-
A simplified channel estimation procedure for NB-IoT downlink
PublikacjaThis paper presents a low-complexity channel estimation procedure which is suitable for use in energy-efficient NB-IoT user equipment devices. The procedure is based on the well-established least squares scheme, followed by linear interpolation in the time domain and averaging in the frequency domain. The quality of channel estimation vs. signal-to-noise ratio is evaluated for two channel models and compared with the performance...
-
Complementary green analytical procedure index (ComplexGAPI) and software
PublikacjaIt is not easy to find appropriate tools for the evaluation of the “green”nature of analytical methodologies which involve the use of compounds, materials, or chemicals manufactured prior to the analytical step. Here, we propose a new metric for the evaluation of analytical procedures based on the GAC attributes. The proposed solution expands on the well-known green analytical procedure index by adding additional fields pertaining...
-
Validation of a sampling procedure
Publikacja -
Grafting and reactive extrusion technologies for compatibilization of ground tyre rubber composites: Compounding, properties, and applications
PublikacjaChemical modification of ground tyre rubber (GTR) to compatibilize it with the matrix is a well-known approach. Based on our recent review of the surface etching methods used in GTR modification, the purpose of the current work is to take a deeper look into more advanced methods such as grafting and reactive extrusion. While grafting is more efficient in achieving compatibility, however, it usually involves multi-step synthesis...
-
Morphology and properties of recycled polyethylene/ground tyre rubber/thermoplastic poly(ester-urethane) blends
PublikacjaThe growing amount of plastics waste produced every year resulted in development of mechanical and chemical recycling methods of polymers and their blends or composites. From the environmental point of view, the possibility of plastics waste reusing and recycling is desirable. In this study three polymer blends were obtained with using recycled polyethylene (RPE), ground tyre rubber (GTR) and thermoplastic poly(ester-urethane)...
-
Experimental investigation of performance and emission characteristics of a miniature gas turbine supplied by blends of kerosene and waste tyre pyrolysis oil
PublikacjaFossil fuels are non-renewable sources of energy that could be depleted in the near future, giving rise to amajor energy crisis. Scientists from all over the world are working on new technologies to produce fuelnot only from renewable sources but also from waste. This article is concerned with: (i) waste tyremanagement by means of the pyrolysis process, (ii) investigation of physico-chemical parameters ofwaste tyre pyrolysis oil...
-
Strength characteristics of tyre chips-sand mixtures.
PublikacjaBadania w aparacie trójosiowego ściskania przy różnej zawartości wagowej kawałków zużytych opon oraz różnym ich ułożeniu w próbce piasku. Badania prowadzono przy dowolnym ułożeniu tych elementów, umieszczeniu ich poziomo oraz w systemie mieszanym. Wyznaczono optymalną zawartość kawałków opon w próbce piasku, przy której występowała maksymalna wytrzymałość na ściskanie.
-
Towards application of uncertainty quantification procedure combined with experimental procedure for assessment of the accuracy of the DEM approach dedicated for granular flow modeling
PublikacjaThere is a high demand for accurate and fast numerical models for dense granular flows found in many industrial applications. Nevertheless, before numerical model can be used its need to be always validated against experimental data. During the validation, it is important to consider how the measurement data sets, as well as the numerical models, are affected by errors and uncertainties. In this study, the uncertainty quantification...
-
An analytical hierarchy process for selection of the optimal procedure for resveratrol determination in wine samples
PublikacjaThe study shows the application of analytical hierarchy process (AHP) in ranking the analytical procedures, that are applied for resveratrol determination in wine samples. 19 different analytical methodologies are described by metrological, economic and environmental criteria, that are further divided into 10 subcriteria. Before AHP application, the amount of input data is decreased with cluster analysis. The first run of AHP is...
-
New procedure for the control of the treatment of industrial effluents to remove volatile organosulfur compounds
PublikacjaWe present a new procedure for the determination of volatile organosulfur compounds in samples of industrial effluents using dispersive liquid–liquid microextraction and gas chromatography with flame photometric detection. Initially, the extraction parameters were optimized. These included: type and volume of extraction solvent, volume of disperser solvent, salting out effect, pH, time and speed of centrifugation as well as extraction...
-
A procedure for the determination of dichloromethane and tetrachloroethene in water using pervaporation and gas chromatography
PublikacjaIn the present study, pervaporation was applied to the determination of tetrachloroethene (PCE) and dichloromethane (DCM) in liquid samples. PCE is the most commonly used solvent in dry-cleaning processes. PCE belongs to group 2A of carcinogens (probably carcinogenic to humans) according to the classification of the International Agency for Research on Cancer (IARC). DCM is also widely used as an industrial solvent for the purification...
-
Effectiveness of Concrete Reinforcement with Recycled Tyre Steel Fibres
Publikacja -
ROSANNE Project: New Procedure for Noise Characterisation of Road Surfaces in Europe
PublikacjaROSANNE is a collaborative project in the 7th EU Framework Programme which aims at harmonising measurement methods for skid resistance, noise emission and rolling resistance of road pavements as a preparation for standardization. The project started in November 2013 and is developing and improving standards in the field of working group CEN/TC 227/WG 5. Regarding the influence of the pavement on the road traffic noise emission,...
-
New procedure for the examination of the degradation of volatile organonitrogen compounds during the treatment of industrial effluents
PublikacjaWe present a new procedure for the determination of 32 volatile organonitrogen compounds in samples of industrial effluents with a complex matrix. The procedure, based on dispersive liquid–liquid microex-traction followed by gas chromatography with nitrogen-phosphorus and mass spectrometric detection, wasoptimized and validated. Optimization of the extraction included the type of extraction and disperser sol-vent, disperser solvent...
-
Application of the IMO standard manoeuvres procedure for pod-driven ships
PublikacjaInternational Maritime Organisation (IMO) in the resolution MSC.137(76) Standards for Ship manoeuvrability presents the manoeuvring criteria that has to be satisfied by majority of seagoing ships. Together with the criteria, procedures for carrying out the manoeuvring tests are also presented. They however do not correspond directly to ships with non-conventional steering-propulsion devices, like pod drives. IMO is aware of this...
-
Projecting procedure for meta-material fiber
PublikacjaWe would like to show new way of derivation evolution equation for short pulses in dielectric waveguide including one model of metamaterial waveguide. This derivation model rely on projecting to the orthogonal basis. In our case to orthogonal basis for cylindrical waveguide.