Wyszukiwarka
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: VIBRATION-BASED DAMAGE DETECTION
-
Application of continuous wavelet transform in vibration based damage detection method for beams and plates
Publikacja -
Application of continuous wavelet transform in vibration based damage detection method for beams and plates
PublikacjaW artykule zaprezentowano metodę lokalizacji uszkodzeń w konstrukcjach belkowych i płytowych bazującą na analizie falkowej. Wyznaczono postacie drgań badanych konstrukcji. Postacie drgań konstrukcji belkowej zostały przeanalizowane jednowymiarową transfrormatą falkową. Sformułowano dwuwymiarową transformatę falkową, którą zastosowano do postaci drgań konstrukcji płytowej.
-
Damage detection in turbine wind blades by vibration based methods
PublikacjaThe paper describes results of numerical simulation for damage localization in the composite coat of a wind turbine blade usingmodal parameters and a modern damage detection method (wavelet transform).
-
VIBRATION PARAMETERS FOR DAMAGE DETECTION IN STRUCTURES
PublikacjaThe aim of this paper is to examine how damage indicators are sensitive to changing number of frequencies and mode shapes and also to number and location of measurement points. The influence of measurement errors was also analyzed for all cases. For the analysis, those damage indicators are chosen which use changes in such modal parameters as natural frequencies and mode shapes and also differences between the curvatures of the damaged...
-
Damage detection in beams using wavelet transform on higher vibration modes
PublikacjaNiniejsza praca poświęcona jest technice diagnostyki konstrukcji bazującej na transformacie falkowej. Badany obiekt to belka wspornikowa z uszkodzeniami w formie nacięcia o głębokości 20%, 10% oraz 5% wysokości belki. Pomiary postaci drgań wykonano za pomocą nowoczesnego wibrometru laserowego. Celem pracy jest przedstawienie eksperymentalnych i numerycznych analiz wpływu wyższych postaci drgań na efektywność wykrywania uszkodzeń...
-
Vibration based damage localization in non-homogeneous structures
PublikacjaPrzedmiotem badań jest identyfikacja lokalnych uszkodzeń w konstrukcjach budowlanych. Przedstawione są trzy metody bazujące na teorii drgań. Są to metody badające: częstości własne, podatność i krzywizny postaci drgań układu. Skuteczność metod pokazana jest na przykładach symulacji komputerowych, wykonanych dla belki swobodnie podpartej, wspornikowej oraz podwieszonej kładki dla pieszych. Dodatkowo zaprezentowane są wyniki badań...
-
Vibration-Based Investigation of a Historic Bell Tower to Understand the Occurrence of Damage
PublikacjaABSTRACT The paper presents a survey of the historic Arch-cathedral bell tower in Vilnius induced by the appearance of cracks in the structure after a new bell system installation. An attempt is undertaken to identify the reason for the crack occurrence and to check a possible crack influence on global structural behaviour. The research is based on dynamic measurements made in the tower during ambient vibrations and during vibrations...
-
Damage detection in plates based on Lamb wavefront shape reconstruction
PublikacjaMany of the current studies in the area of damage detection using elastic wave propagation are based on deploying sensor networks with a large number of piezoelectric transducers to detect small-size cracks. A major limitation of these studies is that cracks are usually larger and have different shapes in real cases. Moreover, using a large number of sensing nodes for damage detection is both costly and computationally intensive....
-
Improvement of damage detection methods based on experimental modal parameters
PublikacjaW pracy przedstwiono sposoby porawy czułości metod detekcji uszkodzeń wykorzystujacych eksperyentalne parametry modalne konstrukcji. Wykazano, że zastosowanie zawansowanych technik obróbki sygnałów pomiarowych pozwala zdecydowanie poprwaić skutecznośc znanych z literatury metod.
-
Damage detection strategies based on propagation of guided elastic waves
PublikacjaW pracy przedstawiono wyniki symulacji numerycznych oraz badań eksperymentalnych nad wykorzystaniemprowadzonych falsprężystych do wykrywania ilokalizacji uszkodzeń w dwu i trójwymiarowych elementach konstrukcyjnych wykonanych z materiałów izotropowych i kompozytowych.
-
Cointegration and wavelet-analysis-based approach for Lamb-wave-based structural damage detection
Publikacja -
RMS-based damage detection in reinforced concrete beams: numerical simulations
PublikacjaImage-based damage detection methods using guided waves are well known and widely applied approaches in structural diagnostics. They are usually utilized in detection of surface damages or defects of plate-like structures. The article presents results of the study of applicability of imaging wave-based methods in detection in miniscule internal damage in the form of debonding. The investigations were carried out on numerical models...
-
Experimental verification and comparison of mode shape-based damage detection methods
PublikacjaThis paper presents experimental verification and comparison of damage detection methods based on changes in mode shapes such as: mode shape curvature (MSC), modal assurance criterion (MAC), strain energy (SE), modified Laplacian operator (MLO), generalized fractal dimension (GFD) and Wavelet Transform (WT).
-
Experimental verification and comparison of mode shape-based damage detection methods
PublikacjaW pracy przedstawiono wynik badań eksperymentalnych dotyczących oceny dokładności znanych z literatury metod detekcji uszkodzeń konstrukcji wykorzystujących zmiany jej parametrów modalnych. Pomiary wykonano wykorzystując skaner laserowy firmy Polytec. Omówiono sposoby poprawy jakości uzyskiwanych wyników, oraz zaproponowano własną metodę detekcji uszkodzeń wykorzystującą pomiar postaci i częstości drgań własnych konstrukcji.
-
Lamb Wave Based Structural Damage Detection Using Stationarity Tests
Publikacja -
Influence of statistical errors on damage detection based on structuralflexibility and mode shape curvature
PublikacjaDamage detection procedures based on measured natural frequencies and building structure mode shapes are discussed in this paper. Modal curvature and structural flexibility approaches are tested. Attention is paid to the modal identification errors that influence damage detection. This problem is studied using a computer simulation of a simple supported beam. For practical cases, the peak picking methodand its statistical errors...
-
Cointegration approach for temperature effect compensation in Lamb-wave-based damage detection
Publikacja -
Lamb wave based structural damage detection using cointegration and fractal signal processing
Publikacja -
Microcracking monitoring and damage detection of graphene nanoplatelets-cement composites based on acoustic emission technology
PublikacjaThis study aims to identify the micro-cracking pattern and structural applications of cement composites replaced with 0 wt%, 0.04 wt%, and 0.08 wt% contents of graphene nanoplatelets (GNPs) over cement weight through acoustic emission (AE) monitoring under mechanical degradation. The ultraviolet-visible spectroscopy (UV–vis) results showed that at 60 min sonication period, GNP-4 showed maximum absorbance rate of 16.15% compared...
-
Stationarity-Based Approach for the Selection of Lag Length in Cointegration Analysis Used for Structural Damage Detection
Publikacja -
Damage detection strategies for aircraft shell-like structures based on propagation guided elastic waves
PublikacjaW pracy przedstawiono mozliwości detekcji uszkodzeń w lotniczych konstrukcjach powłokowych z wykorzystaniem fal sprężystych. Omówiono kilka strategii detekcji uszkodzeń. Przedstawiono wyniki symulacji numerycznych z wykorzystaniem metody spektralnych elementów skończonych, jak również wynik badań eksperymentalnych z zastosowaniem wibrometrii laserowej.
-
Data normalisation for Lamb wave–based damage detection using cointegration: A case study with single- and multiple-temperature trends
Publikacja -
Extended Damage Detection and Identification in Aircraft Structure Based on Multifrequency Eddy Current Method and Mutual Image Similarity Assessment
PublikacjaIn this paper, a novel approach to Non-Destructive Testing (NDT) of defective materials for the aircraft industry is proposed, which utilizes an approach based on multifrequency and spectrogram eddy current method combined with an image analysis method previously applied for general-purpose full-reference image quality assessment (FR IQA). The proposed defect identification method is based on the use of the modified SSIM4 image...
-
Damage Detection in the Wind Turbine Blade Using Root Mean Square and Experimental Modal Parameters
PublikacjaThe paper presents results of an experimental study related to a non-destructive diagnostic technique used for preliminary determination the location and size of delamination in composite coatings of wind turbine blades. The proposed method of damage detection is based on the analysis of the ten first mode shapes of bending vibrations, which correspond to displacements of rotor blades perpendicular to the rotor plane. Modal parameters...
-
Detection of Closing Crack in Beam Based on Responses Induced by Harmonic Excitation
PublikacjaThe non-linear contact model was chosen to simulate the closed crack in the cantilever beam. The study examines the shape and characteristics of the phase diagram of a cantilever beam with closed cracks. It investigates how various crack properties influence the geometry of the phase diagram and proposes a method for identifying cracks based on their features. The area of each closed curve in the phase diagram is determined using...
-
Detection of Delamination in Laminate Wind Turbine Blades Using One-Dimensional Wavelet Analysis of Modal Responses
PublikacjaThis paper demonstrates the effectiveness of a nondestructive diagnostic technique used to determine the location and size of delamination in laminated coatings of wind turbine blades. This is realized based on results of numerical and experimental investigations obtained by the use of the finite element method (FEM) and laser scanning vibrometry (LSV). The proposed method is based on the one-dimensional continuous wavelet transform...
-
Mode shapes of a beam and plate with defects, obtained by experimental modal analysis
Dane BadawczeThe DataSet contains the experimental results of the first mode shape for a beam and a plate.
-
NONLINEAR VIBRATION ANALYSIS OF BEAM AND PLATE WITH CLOSED CRACK: A REVIEW
PublikacjaThe effect of nonlinearity is high sensitivity in damage detection, especially for closed cracks and delamination. This review illustrates the results of several researchers dealing with nonlinear effects caused by the closure of cracks in the structure, i.e., beam and plate structures. Early detection of damage is an important aspect for the structure and, therefore, continuous progress is being made in developing new and effective...
-
SELECTION OF DIAGNOSTIC FUNCTIONS IN A WHEELED TRACTOR
PublikacjaIn a classical approach to damage diagnosis, the technical condition of an analyzed machine is identified based on the measured symptoms, such as performance, thermal state or vibration parameters. In wheeled tractor the fundamental importance has monitoring and diagnostics during exploitation concerning technical inspection and fault element localizations. The main functions of a diagnostic system are: monitoring tractor components...
-
Motor bearing diagnostics performed by means of laser vibrometer
PublikacjaDamage of bearings is the most common cause of failures in squirrel-cage induction motors. That is why the issues connected with diagnostics of bearings are so important. The equipment employed for bearing diagnostics usually makes use of vibrations as the criterion for technical condition of the bearings. This paper presents exemplary results of the research conducted on bearings with artificially introduced damage. A scanning...
-
Wave Method for Structural Health Monitoring: Testing Using Full-Scale Shake Table Experiment Data
PublikacjaAn algorithm of the wave method for structural health monitoring (SHM) is tested and calibrated using shake table experiment data of a full-scale, seven-story, reinforced-concrete building slice. The method is based on monitoring changes in the velocity of waves propagating vertically through the structure, identified by least-squares (LSQ) fit of beam models. The experiment was conducted by a team from the University of California,...
-
DIAGNOSTYKA ŁOŻYSK SILNIKA INDUKCYJNEGO PRZY UŻYCIU POMIARU PRĄDU ZASILAJĄCEGO I WIBRACJI
PublikacjaW artykule przedstawione zostały wyniki badań diagnostycznych łożysk silnika indukcyjnego z zastosowaniem metody pomiaru prądu zasilającego oraz wibracji. Poruszone zostały problemy dotyczące poszukiwania nowej metody opartej na pomiarze i analizie prądu, która w znacznym stopniu ułatwiłaby szybkie i sprawne znalezienie uszkodzenia w maszynie, bez konieczności bezpośredniego dostępu do badanego urządzenia. Zaprezentowano rezultaty...
-
Experimental dynamic study on a timber-frame house using shaking table
PublikacjaThe aim of this paper is to show the results of the shaking table experimental study concerning the behaviour of the model of the timber-frame house under earthquake excitation and impact loading. In order to determine the basic dynamic properties of the undamaged structure, the free vibration and the sweep-sine tests were first conducted. Then, the model was excited using the time history record of the El Centro earthquake of...
-
Diagnosis of Damage in a Steel Tank Model by Shaking Table Harmonic Tests
PublikacjaThe aim of the present paper is to show the results of the shaking table experimental study concerning the diagnosis of damage in a model of cylindrical steel tank with self-supported roof which is filled with liquid. During the tests, the base of the structure was excited under the harmonic loading with variable frequency. The tests were repeated for different stages of damage, which was introduced in the model by easing the bolts...
-
Numerical investigation on behaviour of cylindrical steel tanks during mining tremors and moderate earthquakes
PublikacjaCylindrical steel tanks are important components of industrial facilities. Their safety becomes a crucial issue since any failure may cause catastrophic consequences. The aim of the paper is to show the results of comprehensive FEM numerical investigation focused on the response of cylindrical steel tanks under mining tremors and moderate earthquakes. The effects of different levels of liquid filling, the influence of non-uniform...
-
Structural Health Monitoring System for Suspension Footbridge
PublikacjaThe article presents the structural health monitoring (SHM) system installed in a footbridge in Radom. The main reason for the need for fitting of such a system was failed acceptance tests of the bridge. While under a dynamic load consisting of a group of 12 pedestrians jumping on the bridge, the bridge developed vibration during which acceleration of the deck of up to 4.5 m/s2 was recorded. Such behavior of the footbridge causes...
-
VIBRATION DIAGNOSTICS OF FOOTBRIDGE WITH USE OF ROTATION SENSOR
PublikacjaThe benefits of the additional measurement of rotational degrees of free-dom on the performance of the vibration diagnosis of bridges are studied in this paper. The common vibrational diagnostics that uses translational degrees of freedom is extended by measurements of rotations. The study is curried out on a footbridge and the presence of damage as well as its location and size is determined with use of FEM updating procedure....
-
Diagnosis of Damage in a Steel Tank Model by Shaking Table Harmonic Tests
PublikacjaDiagnosis of damage in civil engineering structures has recently become an important issue in the safety assessment procedure. Among a number of different approaches, a method of measuring the changes in natural frequencies is one of the most effective indicators of global damage. It has been successfully applied to relatively small. structures, however, the tests on large structures are very difficult and the practical application...
-
Diagnostic system of wheeled tractors detecting four defect's categories
PublikacjaIn a classical approach to damage diagnosis, the technical condition of an analyzed machine is identified based on the measured symptoms, such as performance, thermal state or vibration parameters. In wheeled tractor the fundamental importance has monitoring and diagnostics during exploitation concerning technical inspection and fault element localizations. The main functions of a diagnostic system are: monitoring tractor components...
-
MCSA with Normalized Triple Covariance as a bearings diagnostic indicator in an induction motor
PublikacjaStatistics of bearing failures in induction motors indicate, that they constitute more than 40% of IM damage, therefore bearing diagnosis is very important. Vibration methods for bearing diagnostics have one major disadvantage - they require the availability of the machine for sensors installation. This is the reason for seeking new methods based on motor supply current analysis. Diagnosis of induction motors, conducted remotely...
-
Induction motor bearings diagnostic indicators based on MCSA and normalized triple covariance
PublikacjaInduction motors are one of the most widely used electrical machines. Statistics of bearing failures of induction motors indicate, that they constitute more than 40% of induction motor damage. Therefore, bearing diagnosis is so important for trouble-free work of induction motors. The most common methods of bearing diagnosis are based on vibration signal analysis. The main disadvantage of those methods is the need for physical access...
-
Diagnosis of Damage in a Steel Tank with Self-Supported Roof through Numerical Analysis
PublikacjaThe safety of civil engineering structures is one of the most important issues of building industry. That is why the assessment of the damage-involved structural response has recently become of major concern to engineers. Among a number of different approaches to diagnosis of damage, the method of measuring the changes in natural frequencies is considered to be one of the most effective indicators of global damage. From the practical...
-
Diagnostics of induction motor bearings - possibility of measurements
PublikacjaIn induction motors damage in the elements of electromagnetic system, for example in the wiring of stator, rotor or in the magnetic circuit can appear as well as damage of mechanical parts (bearings, rotor, shaft). Bearing diagnostics is so important in supervision of motor condition, because extensive research shows that the bearings arethe elements most susceptible to damage. This paper presents the research which the author...
-
Effective Gap Size Index for Determination of Optimum Separation Distance Preventing Pounding between Buildings during Earthquakes
PublikacjaSeismic excitations may lead to collisions between adjacent civil engineering structures causing major damage. In this paper, an effective equation for calculating the gap size index is proposed so as to provide the optimum separation distance preventing structural pounding during different earthquakes. Evaluation of the best prediction of the required separation distance between two adjacent buildings was carried out by using...
-
Eulerian motion magnification applied to structural health monitoring of wind turbines
PublikacjaSeveral types of defects may occur in wind turbines, as physical damage of blades or gearbox malfunction. A wind farm monitoring and damage prediction system is built to observe abnormal vibrations of elements of wind turbine: blades, nacelle, and tower. Contactless methods are developed which do not require turbine stopping. In this work, structural health monitoring of a wind turbine is evaluated using a conversion from the captured...
-
Experimental study on models of cylindrical steel tanks under mining tremors and moderate earthquakes
PublikacjaThe aim of the study is to show the results of complex shaking table experimental investigation focused on the response of two models of cylindrical steel tanks under mining tremors and moderate earthquakes, including the aspects of diagnosis of structural damage. Firstly, the impact and the sweep-sine tests have been carried out, so as to determine the dynamic properties of models filled with different levels of liquid. Then,...
-
Diagnostyka ultradźwiękowa mostowej belki prefabrykowanej typu T metodą młoteczkową
PublikacjaZastosowanie prefabrykacji w budowie obiektów mostowych pozwala optymalizować zużycie energii i materiałów i tym samym redukować koszty budowanego obiektu. Prefabrykowane belki sprężone mogą występować jako elementy kablobetonowe wykonywane bezpośrednio na placu budowy lub powstawać w zakładzie prefabrykacji jako elementy strunobetonowe. Elementy prefabrykowane wytwarzane w warunkach przemysłowych muszą spełniać wymagania wysokiej trwałości,...
-
Supply current signal and artificial neural networks in the induction motor bearings diagnostics
PublikacjaThis paper contains research results of the diagnostics of induction motor bearings based on measurement of the supply current with usage of artificial neural networks. Bearing failure amount is greater than 40% of all engine failures, which makes their damage-free operation crucial. Tests were performed on motors with intentionally made bearings defects. Chapter 2 introduces the concept of artificial neural networks. It presents...
-
Application of RMS for damage detection by guided elastic waves
PublikacjaThis paper presents certain results of an experimental study related with a damage detection in structural elements based on deviations in guided elastic wave propagation patterns.
-
In-service measurement of the small wind turbine test stand for structural health monitoring
PublikacjaThis paper presents the research activity performed on a Small Wind Turbine (SWT) test stand. Commercially available turbine was modified towards incorporation of the sensors system for condition monitoring. Installed sensors measure angular shaft position, torque applied from the wind loads, vibration accelerations and last but not least rotational speed. All gathered data are then transferred and processed in Test.Lab by means...