Filtry
wszystkich: 723
-
Katalog
Wyniki wyszukiwania dla: AUDIO CLIPPING
-
Tripping limitations of residual current devices in photovoltaic installations
PublikacjaIn electrical installations with photovoltaic sources of energy, earth fault current may comprise alternating current component and direct current component. The waveform shape of this earth fault current mainly depends on the point of the fault and the properties of a photovoltaic power electronics converter. The waveform shape of the current influences operation of protection devices, especially tripping threshold of residual...
-
Low-frequency tripping characteristics of residual current devices
PublikacjaFast development of various types of converters makes their utilization in industry and in domestic installations very common. Due to converters, an earth fault current waveform in modern circuits can be distorted or its frequency can be different than 50/60 Hz. Frequency of earth fault (residual) current influences tripping of residual current devices which are widely used in low voltage systems. This paper presents the behaviour...
-
Results of abrasive slurry dosage in lapping process
PublikacjaPrzedstawiono wyniki badań dawkowania zawiesiny ściernej w docieraniu powierzchni płaskich elementów ceramicznych. Analizowano wpływ dawkowania na podstawowe parametry chropowatości powierzchni ceramiki Al2O3 i Al2O3-ZrO2.
-
Surface contamination after lapping by abrasive material
PublikacjaPrzedstawiono wyniki badań skażenia powierzchni żeliwa sferoidalnego mikroziarnami węglika krzemu po docieraniu. Określowo wpływ współczynnika upakowania mikroziaren w strefie docierania na intensywność skażenia powierzchni ścierniwem. W badaniach wykorzystano powierzchniową mikroanalizę rentgenowską.
-
Implementation of DIFAR Processing in ASW Dipping Sonar
PublikacjaThis paper presents the implementation of the signal processing algorithm used by buoy DIFAR (Directional Frequency Analysis and Recording), that is fully operational on Polish Navy anti-submarine warfare (ASW) helicopters and ships, applied to dipping sonars for detection and tracking of submarines. The development of the DSP algorithms was a part of the modernization of sonars conducted at the Gdansk University of Technology....
-
Influence of Flat Lapping Kinematics on Machinability of Ceramics
PublikacjaNew tools for flat grinding of ceramics are presented in the paper. Electroplated CBN tools (B64 and B107) were used in a modified single-disc lapping machine configuration. The results from experiments, such as the material removal rate and surface roughness parameters are presented and analyzed. Numerical simulations, based on the model for the shape error and tool wear estimation in machining with flat lapping kinematics, are...
-
Shaping of the workpiece surface in single-disc lapping
PublikacjaShape errors of the tool exert a dominant influence on the shape accuracy of the workpiece. The correlation between flatness errors of the lap and flatness errors of the workpieces was checked experimentally and determined analytically. Computer model of the workpiece shaping by lapping was developed. Evaluation method of the workpiece orientation as well as some simulation results for a lap with shape errors of convexity and cincavity...
-
Research on the wear evenness of the tool in flat lapping
PublikacjaIn this paper, the dimensionless distribution of the material removal stock and the trajectories of abrasive grains cutting in single-sided lapping process are presented. They were numerically simulated based on the tribological model and kinematics equations. It can be observed that the trajectories geometry of single abrasive as well the velocities have a great influence on the final geometrical deviation. During machining, the...
-
Emissivity of the one-plate lapping machine tool
PublikacjaPrzedstawiono wyniki badań własnych emisyjności docieraka żeliwnego docierarki jednotarczowej. Omówiono konstrukcje produkowanych docierarek jednotarczowych wyposażonych w system kontroli temperatury lub chłodzenia tarczy docierającej. Podano warunki pomiarów temperatury przy użyciu kamery termowizyjnej typu V-20II firmy VIGO System S.A.
-
The idea of a robotic single-sided lapping system
PublikacjaThis paper reviews the idea of a robotic lapping system. Robot’s assistance automates the lap-ping process and supports the development of a flexible lapping system. However, the main aim behind the idea of a robotic lapping system is to provide improved means for controlling the posi-tion of conditioning rings on a lapping plate. Due to the kinematics of lapping process, the profile wear of the tool is not constant along the radius....
-
Analysis of flat compensator lapping in an assembly process
PublikacjaPrzedstawiono sposób analizy docierania kompensatora płaskiego podczas montażu połączenia konstrukcyjnego. Wyznaczono czas główny obróbki i koszty operacji docierania jednotarczowego
-
Shaping of the workpiece surface in single-disc lapping
PublikacjaPrzedstawiono korelację pomiędzy błędami kształtu docieraka i błędami kształtu przedmiotów obrabianych. Wyniki analityczne zostały sprawdzone doświadczalnie, co pozwoliło zbudować komputerowy model kształtowania powierzchni docieranych. Przedstawiono sposób wyznaczania intensywności kontaktu między przedmiotem docieranym, a docierakiem. Opracowano metodę wyznaczania położenia przedmiotu na docieraku.
-
Problems of flat surface lapping : chapter 16
PublikacjaPrzedstawiono problemy docierania powierzchni płaskich w układach jednotarczowych. Omówiono analityczne i numeryczne modele kinematyki docierarek konwencjonalnych i niestandardowych, obróbkę docierakami aktywizowanymi w sposób swobodny i wymuszony, jednolitymi i dwumetalowymi. Zaprezentowano wyniki obróbki narzędziami ścierno-metalowymi elementów ceramicznych.
-
Lapping of flat surfaces with two metallic tools.
PublikacjaPrzedstawiono opis docierania powierzchni płaskich docierakami aktywizowanymi w sposób swobodny i wymuszony oraz narzędziami dwumetalowymi i ściernometalowymi. Wyznaczono zużycie docieraków stalowo-żeliwnych oraz wydajność obróbki żeliwa sferoidalnego niestopowego i stali NC6.
-
ANALYSIS OF THE RESULTS OF THE AUDIT OF LIGHTING PARAMETERS AT PEDESTRIAN CROSSINGS IN WARSAW
PublikacjaThe night time, based on many world studies, generates an increased risk of serious accidents (with fatalities and serious injuries). This is especially true for accidents with pedestrians. Pedestrian crossings are very sensitive to the influence of the time of day in terms of pedestrian safety, elements of road infrastructure. This is visible on the example of Poland, where numerous accidents at crosswalks are recorded, characterized...
-
Evaluation of Six Degrees of Freedom 3D Audio Orchestra Recording and Playback using multi-point Ambisonic interpolation
PublikacjaThis paper describes a strategy for recording sound and enabling six-degrees-of-freedom playback, making use of multiple simultaneous and synchronized Higher Order Ambisonics (HOA) recordings. Such a strategy enables users to navigate in a simulated 3D space and listen to the six-degrees-of-freedom recordings from different perspectives. For the evaluation of the proposed approach, an Unreal Engine-based navigable 3D audiovisual...
-
Analiza jakości transmisji treści audio-wideo w symulowanym łączu telekomunikacyjnym z wykorzystaniem techniki OFDM
PublikacjaWdrożenie niezawodnego systemu komunikacji audio-wideo przynosi wiele korzyści. Z uwagi na fakt, że ilość dostępnego pasma stale się kurczy, badacze koncentrują się na nowatorskich metodach transmisji. Obecnie technika OFDM (Orthogonal Frequency Division Multiplexing) jest szeroko stosowana zarówno w mediach przewodowych, jak i bezprzewodowych. W pracy przedstawiono badania jakości QoS (Quality of Service) symulowanego łącza transmisji...
-
Analysis of impact of lossy audio compression on the robustness of watermark embedded in the DWT domain for non-blind copyright protection
PublikacjaA methodology of non-blind watermarking of the audio content is proposed. The outline of audio copyright problem and motivation for practical applications are discussed. The algorithmic theory pertaining watermarking techniques is briefly introduced. The system architecture together with employed workflows for embedding and extracting the watermarks are described. The implemented approach is described and obtained results are reported....
-
A commonly-accessible toolchain for live streaming music events with higher-order ambisonic audio and 4k 360 vision
PublikacjaAn immersive live stream is especially interesting in the ongoing development of telepresence tools, especially in the virtual reality (VR) or mixed reality (MR) domain. This paper explores the remote and immersive way of enabling telepresence for the audience to high-fidelity music performance using freely-available and easily-accessible tools. A functional VR live-streaming toolchain, comprising 360 vision and higher-order ambisonic...
-
Online sound restoration system for digital library applications
PublikacjaAudio signal processing algorithms were introduced to the new online non-commercial service for audio restoration intended to enhance the content of digitized audio repositories. Missing or distorted audio samples are predicted using neural networks and a specific implementation of the Jannsen interpolation method based on the autoregressive model (AR) combined with the iterative restoring of missing signal samples. Since the distortion...
-
Tripping of F-type RCDs for High-Frequency Residual Currents
PublikacjaResidual current devices (RCDs) are apparatus commonly used for protection against electric shock in low-voltage electrical installations. They protect people in the case of an earth fault or even in the case of direct contact with the live parts. However, to be effective protective devices, RCDs have to detect residual currents of various waveform shapes which appear in modern electrical installations. For this purpose, RCDs...
-
The effect of current delay angle on tripping of residual current devices
PublikacjaPower electronics converters applied in domestic or similar installations may utilize current delay (phase) angle control to change the level of transferred power. Due to application of such types of converters, earth fault current in the installation may be strongly distorted. The current distortion level depends on a value of current delay angle. This delay angle also influences the tripping threshold of residual current devices....
-
Time-current tripping curves of arc fault detection devices
PublikacjaTripping curves of arc fault detection devices, in accordance with PN-EN 62606 “General requirements for arc fault detection devices” have been presented in the paper. Consequently the most fundamental differences in arc fault detection devices tripping compared to circuit-breakers and residual current devices have been indicated.
-
Shipping Low Frequency Noise and Its Propagation in Shallow Water
PublikacjaOne of the most significant factor influencing acoustical climate of the sea is underwater noise generated by moving ships. If the considered sea area has features of the shallow water, namely the wave frequency fulfils relation f < 10c/h, where c denotes phase speed of sound, and h is depths of the sea, then in certain distance from the wave source specific image of sound pressure distribution in the mean of wave modes appears....
-
Time-current tripping characteristics of RCDs for sinusoidal testing current
PublikacjaLow-voltage electrical installations are verified initially – before being put into operation, as well as periodically – during their utilization. According to the IEC standards, the scope of the verification includes measurements of both the tripping current and the disconnection time of residual current devices (RCDs). Experiences in RCDs testing show that disconnection times of two or more similar RCDs can be quite different....
-
Tripping of F-type RCDs for high-frequency residual currents
PublikacjaResidual current devices (RCDs) are apparatus commonly used for protection against electric shock in low-voltage electrical installations. They protect people in the case of an earth fault or even in the case of direct contact with the live parts. However, to be effective protective devices, RCDs have to detect residual currents of various waveform shapes which appear in modern electrical installations. For this purpose, RCDs are...
-
Clamping precision of a cilcular saw blade on a spindle of a sawing machine
PublikacjaW pracy przedstawiono analizę dokładności mocowania piły tarczowej na wrzecionie pilarki, w której uwzgledniono jedynie tolerancje wykonania układu wrzeciona pilarki i piły tarczowej.
-
International Journal of Shipping and Transport Logistics
Czasopisma -
Microgrinding of flat surfaces on single-disc lapping machine
PublikacjaW pracy przedstawiono możliwości zastosowania specjalnych narzędzi do mikroszlifowania na docierarce jednotarczowej. Jedno z zastosowanych narzędzi posiada warstwę ścierniwa diamentowego (D64) nałożoną metodą galwaniczną. Drugie przetestowane narzędzie zbudowane zostało z diamentowych pastylek ściernych (D3/2). Przedstawiono analizę kinematyczną i wyniki ubytku materiałowego oraz osiągnięte parametry chropowatości.
-
Simulation of the profile wear of the tool in double wheel lapping
PublikacjaW pracy przedstawiono model zużycia narzędzia w docieraniu dwutarczowym. Wyprowadzono równania opisujące kontakt przedmiotu z narzędziem. Przedstawiono wyniki analiz symulacyjnych dla różnych parametrów kinematycznych - dla układu współbieżnego i przeciwbieżnego.
-
Microgrinding of flat surfaces on single-disk lapping machine
PublikacjaW pracy przedstawiono wyniki badań mikroszlifowania z kinematyką docierania w układzie jednotarczowym z wykorzystaniem nowego narzędzia wykonanego z pastylek ściernych z ziarnem diamentowym (D3/2) i spoiwem żywicznym. Zakres pracy obejmował przeprowadzenie badań eksperymentalnych i modelowych związanych z analizą promienia krzywizny rys obróbkowych.
-
Wear of the tool in double-disc lapping of silicon wafers
PublikacjaPrzedstawiono założenia modelowe do określania zużycia narzędzia w docieraniu krzemowych płytek półprzewodnikowych. Obliczenia zostały wykonane dla różnych parametrów kinematycznych, wpływających na zużycie narzędzia w określonych jego obszarach.
-
Finishing of Ceramics in a Single-Disk Lapping Machine Configuration
PublikacjaPrzedstawiono metodę obróbki ceramiki technicznej na zmodifikowanej docierarce jednotarczowej z niezależnym napędem pierścienia prowadzącego. Omówiono przebieg obróbki z wykorzystaniem nowych narzędzi i zastosowaniem ziarna wiązanego.
-
Technological aspects of microgrinding with single-disc lapping kinematics
PublikacjaPrzedstawiono wyniki badań mikroszlifowania powierzchni płaskich na docierarce jednotarczowej. Badano stan powierzchni narzędzia wykonanego na bazie mikroziaren diamentowych D65/50 naniesionych galwanicznie na podłoże stalowe. Analizowano wydajność obróbki oraz chropowatość powierzchni elementów ze stali 18G2A.
-
Lapping flat surfaces with forced dosing of abrasive suspension
PublikacjaPrzedstawiono zbudowane stanowisko do badań wymuszonego dawkowania zawiesiny ściernej w procesie jednostronnego docierania powierzchni płaskich. Podano przyjęty program badań oraz sposób opracowania wyników realizowanych eksperymentów.
-
Lapping flat surfaces with forced dosing of abrasive suspension
PublikacjaPrzedstawiono zbudowane stanowisko badawcze umożliwiające wymuszone dozowanie zawiesiny ściernej w operacji docierania jednotarczowego powierzchni płaskich. Podano program badań własnych oraz sposób opracowania otrzymanych wyników realizowanych eksperymentów.
-
Microgrinding of flat surfaces on a single-disc lapping machine
PublikacjaW referacie przedstawiono wyniki badań eksperymentalnych mikroszlifowania z kinematyką docierania jednotarczowego. Przedstawiono propozycję narzędzia z wkładkami ściernymi z ziarnem diamentowym D3/2 i spoiwem żywicznym. Omówiono kinematykę docierania jednotarczowego i sposób oceny krzywizny rys obróbkowych.
-
Analysis of machining marks curvature in single disk lapping
PublikacjaW referacie przedstawiono wyniki badań symulacyjnych i eksperymentalnych dotyczących wyznaczania i oceny krzywizny śladów obróbkowych po obróbce mikroszlifowaniem z kinematyką docierania jednotarczowego.
-
Research on Tool Temperature Dependence on Lapping Grains Size
PublikacjaCommonly used as a finishing operation, lapping has been used for achieving ultra-high finishes and close tolerances between mating pieces. Its carried out by applying loose abrasive grains between work and lap surfaces, and causing a relative motion between them resulting in a finish of multi-directional lay. The grains activity (sliding and rolling) in the working gap causes not only the material removal but also the temperature...
-
Technological Problems in Lapping on Flat Surfaces of Ceramic Parts
PublikacjaThis paper will present the results of research on single-disc lapping of flat surfaces of small ceramic elements. Machining with the use of different tools such as metallic, two-metallic and abrasive-metallic will be analyzed. The basics and techniques of reinforcement of laps will be discussed. The results of the influence of parameters on the surface quality of ceramic conponents (sealing) for three treatments on lapping machines...
-
Tendencies in abrasive machining with lapping kinematics - experimental studies
PublikacjaW pracy przedstawiono tendencje rozwoju obróbki ściernej z wykorzystaniem kinematyki docierania. Zaprezentowano wyniki badań szlifowania specjalnymi narzędziami w układzie docierarki jedno- i dwutarczowej.
-
Determining the conditions for temperature measurements during flat lapping
PublikacjaPrzedstawiono pomiary temperatury układu wykonawczego docierarki jednotarczowej ABRALAP 380. Badano wpływ liczby stosowanych pierścieni prowadzących przy docieraniu elementów ceramicznych mikroziarnami węglika krzemu. Analizowano przyrost temperatury układu w czasie do trzech godzin. W badaniach zastosowano kamerę termowizyjną V-20II firmy VIGO System S.A.
-
Tool Wear Prediction in Single-Sided Lapping Process
PublikacjaSingle-sided lapping is one of the most effective planarization technologies. The process has relatively complex kinematics and it is determined by a number of inputs parameters. It has been noted that prediction of the tool wear during the process is critical for product quality control. To determine the profile wear of the lapping plate, a computer model which simulates abrasive grains trajectories was developed in MATLAB. Moreover,...
-
Simulation of the profile wear of the tool in double wheel lapping
PublikacjaPrzedstawiono założenia modelowe do wyznaczenia zużycia profilowego narzędzia w docieraniu dwutarczowym. Rozkłady istotnych czynników kinematycznych (prędkości docierania i przyspieszenia stycznego) wpływających na zużycie docieraka zaprezentowane zostały dla różnych typów zakreślanych trajektorii.
-
Machining of the flat surfaces with abrasive-metallic lapping tools.
PublikacjaPrzedstawiono konstrukcje narzędzi ścierno-metalowych do obróbki powierzchni płaskich na docierarkach jednotarczowych. Przeprowadzono badania wydajności i jakości powierzchni elementów ceramicznych o małych gabarytach.
-
Accounting Quality and Audit Attributes on the Stock Price Crashes in an Emerging Market
Publikacja -
Audit wewnętrzny procesów systemu zarządzania jakością. Perspektywa małych organizacji
PublikacjaPrzedstawio metodykę auditowania procesów systemów zarzadzania jakością oraz specyficzne uwarunkowania z tym związane występujące wmałych organizacjach.
-
Adaptive system for recognition of sounds indicating threats to security of people and property employing parallel processing of audio data streams
PublikacjaA system for recognition of threatening acoustic events employing parallel processing on a supercomputing cluster is featured. The methods for detection, parameterization and classication of acoustic events are introduced. The recognition engine is based onthreshold-based detection with adaptive threshold and Support Vector Machine classifcation. Spectral, temporal and mel-frequency descriptors are used as signal features. The...
-
Elimination of Impulsive Disturbances From Stereo Audio Recordings Using Vector Autoregressive Modeling and Variable-order Kalman Filtering
PublikacjaThis paper presents a new approach to elimination of impulsive disturbances from stereo audio recordings. The proposed solution is based on vector autoregressive modeling of audio signals. Online tracking of signal model parameters is performed using the exponential ly weighted least squares algo- rithm. Detection of noise pulses an d model-based interpolation of the irrevocably distorted sampl es is realized using an adaptive, variable-order...
-
Online sound restoration system for digital library applications.
PublikacjaAudio signal processing algorithms were introduced to the new online non-commercial service for audio restoration intended to enhance the content of digitized audio repositories. Missing or distorted audio samples are predicted using neural networks and a specific implementation of the Jannsen interpolation method based on the autoregressive model (AR) combined with the iterative restoring of missing signal samples. Since the distortion...