prof. dr hab. inż. Piotr Jasiński
Employment
- Head of Department at Katedra Inżynierii Materiałów Funkcjonalnych WETI
- Professor at Katedra Inżynierii Materiałów Funkcjonalnych WETI
Research fields
Publications
Filters
total: 289
Catalog Publications
Year 2016
-
3D polypyrrole structures as a sensing material for glucose detection
PublicationIn this work, 3D polypyrrole (PPy) structures as material for glucose detection is proposed. Polypyrrole was electrochemically polymerized on platinum screen-printed electrode from an aqueous solution of lithium perchlorate and pyrrole. The growth mechanism of such PPy structures was studied by ex-situ scanning electron microscopy. Preliminary studies show that studied here PPy film is a good candidate as a sensing material for...
-
Barium boron aluminum silicate glass system for solid state optical gas sensors
PublicationRecent increasing demand for new eco-friendly materials and for low cost fabrication process for use in optical sensors field, raise concern about alternative materials for this application. We have designed two glass-ceramics compositions from the quaternary ROAl2O3- SiO2-B2O3(R=Ba) alkali-earth aluminum silicate system, labeled B72 and B69, with high refractive index (>1.6), large values of Abbe number (94.0 and 53.0, respectively),...
-
CGO as a barrier layer between LSCF electrodes and YSZ electrolyte fabricated by spray pyrolysis for solid oxide fuel cells
PublicationPerovskite La0.6Sr0.4Co0.2Fe0.8O3 − δ (LSCF) is often used as a cathode material for solid oxide fuel cells (SOFC) due to high mixed ionic and electronic conductivity and good catalytic activity. Unfortunately, sintering of the LSCF cathode together with the yttria stabilized zirconia (YSZ) electrolyte, leads to formation of the La2Zr2O7 and SrZrO3 phases in the interface. These phases increase the resistance of the cell. To avoid...
-
Conductivity and viscosity changes of imidazolium ionic liquids induced by H2O and CO2
PublicationSeveral solutions of ionic liquids based on 1-ethyl-3-methylimidazolium cation saturated and unsaturated with carbon dioxide were prepared and characterized by electrochemical impedance spectroscopy. The in fluence of ILs saturation on its electrical conductivity was determined. Additionally, the in fluence of the water presence and variations of temperature on electrical properties of ionic liquids were investigated. Changes of...
-
Determination of chlorine concentration using single temperature modulated semiconductor gas sensor
PublicationA periodic temperature modulation using sinusoidal heater voltage was applied to a commercial SnO2 semiconductor gas sensor. Resulting resistance response of the sensor was analyzed using a feature extraction method based on Fast Fourier Transformation (FFT). The amplitudes of the higher harmonics of the FFT from the dynamic nonlinear responses of measured gas were further utilized as an input for Artificial Neural...
-
Determination of the ionic conductivity of Sr-doped lanthanum manganite by modified Hebb–Wagner technique
PublicationThe Hebb–Wagne rpolarization method with the electron blocking electrode has been discussed in this paper in aim to determine a partial ionic conductivity of Sr-doped lanthanum manganite.The “limiting current” in the proposed system was measured using the two-point DC technique with additional Pt electrode between LSM and blocking electrode.The electrochemical model based on bulk diffusion processes and Boltzmann statistics has...
Year 2015
-
A calibration model for gas sensor array in varying environmental conditions
PublicationAbstract: Gas-analyzing systems based on gas sensors, commonly referred to as electronic noses, are the systems which enable the recognition of volatile compounds in their working environment and provide the on-line results of analysis. The most commonly used type of sensors in such systems is semiconductor gas sensors. They are considered to be the most reliable in the long-term applications (more than 1 year), however,...
-
Assesment of (Mn,Co)3O4powders for possible coating material for SOFC/SOEC interconnects
PublicationIn this work (Mn,Co)3O4 spinel powders with different Mn:Co ratio (1:1 and 1:2) and from different commercial suppliers are evaluated for possible powder for production of interconnect coatings. Sinterability of the powders is evaluated on pressed pellets sintered in oxidizing and in reducing/oxidizing atmospheres. For selected powder, coatings are then prepared by the electrophoretic deposition method on Crofer 22 APU stainless...
-
Characterization of magnesium doped lanthanum orthoniobate synthesized by molten salt route
PublicationMolten salt synthesis method has been used to prepare the single phase magnesium doped lanthanum orthoniobate. The phase composition has been checked by X-ray diffraction method and the microstructure studies have been performed by scanning electron microscopy. The high temperature properties of the material have been investigated by thermogravimetry and electrochemical impedance spectroscopy. A dependence between sample total...
Year 2014
-
A calibration model for gas sensor array in varying environmental conditions
PublicationAbstract: Gas-analyzing systems based on gas sensors, commonly referred to as electronic noses, are the systems which enable the recognition of volatile compounds in their working environment and provide the on-line results of analysis. The most commonly used type of sensors in such systems is semiconductor gas sensors. They are considered to be the most reliable in the long-term applications (more than 1 year), however,...
-
CeCu2O4 as a functional layer on solid oxide fuel cells for synthetic biogas reforming
PublicationSolid Oxide Fuel Cells (SOFC) are one of the most promising electrochemical devices, which can convert chemical energy to the electrical energy these days. Their ability to work with different kind of fuel makes them noteworthy. SOFC can work with biogas. The problem arises when solid carbon starts to be deposited in anode. That leads to degradation of fuel cell. Simple solution is to apply catalytic functional layer, which is...
-
Ceria Based Protective Coatings for Steel Interconnects Prepared by Spray Pyrolysis
PublicationStainless steels can be used in solid oxide fuel/electrolysis stacks as interconnects. For successful long term operation they require protective coatings, that lower the corrosion rate and block chemical reactions between the interconnect and adjacent layers of the oxygen or the hydrogen electrode. One of the promising coating materials for the hydrogen side is ceria. Using standard sintering techniques, ceria sinters at around...
-
Determination of toxic gases based on the responses of a single electrocatalytic sensor and pattern recognition techniques
PublicationA response from an electrocatalytic gas sensor contains fingerprint information about the type of gas and its concentration. As a result, a single gas sensor can be used for the determination of different gases. However, information about the type of gas and its concentration is hidden in the unique shape of the current–voltage response and it is quite difficult to explore. One of the ways to get precise information about the measured...
Year 2022
-
A dual-control strategy based on electrode material and electrolyte optimization to construct an asymmetric supercapacitor with high energy density
PublicationMetal-organic frames (MOFs) are regarded as excellent candidates for supercapacitors that have attracted much attention because of their diversity, adjustability and porosity. However, both poor structural stability in aqueous alkaline electrolytes and the low electrical conductivity of MOF materials constrain their practical implementation in supercapacitors. In this study, bimetallic CoNi-MOF were synthesized to enhance the electrical...
-
Cu-Doped Layered Double Hydroxide Constructs the Performance-Enhanced Supercapacitor Via Band Gap Reduction and Defect Triggering
PublicationLayered double hydroxides (LDHs) are regarded as the excellent electrode materials for supercapacitors because of their high theoretical capacitance and abundance. However, the poor conductivity and limited reaction kinetics of LDHs restrict their practical application severely. Herein, Cu is chosen from groups VIII/IB/IIB as dopants for Co-based LDH (CuCo-LDH). The designed metal–organic framework-derived hierarchical CuCo-LDH...
Year 2007
-
A novel technology of solid oxide fuel cell fabrication
PublicationW pracy przedstawiono metodę wytwarzania wartstw i materiałów elektroceramicznych. Metoda jest kombinacją metod nanoszenia szkieletu z proszków ceramicznych i prekursorów polimerowych. Umożliwia ona otrzymanie zarówno gęstych jak i porowatych warstw i materiałów jednorodnych oraz kompozytowych. W pracy przedstawiono przykłady struktur dla tlenkowych ogniw paliwowych.
-
Amperometryczne czujniki gazów z membraną nafionową
PublicationW pracy przedstawiono krótki przegląd najnowszych osiągnięć w dziedzinie konstrukcji amperometrycznych czujników gazów, w szczególności z membranami wykonanymi z polimerów przewodzących. Dokonano oceny wpływu niektórych parametrów na właściwości metrologiczne tego rodzaju czujników na przykładzie czujnika ditlenku siarki, także w oparciu o wyniki badań własnych prototypów czujników.
Year 2006
-
An application of advanced data processing methods to response analysis of electrocatalytic gas sensor
PublicationPrzedstawiono stosowane dotychczas oraz zaproponowano nowe metody analizy odpowiedzi czujników elektrokatalitycznych. Porównano ich właściwości.
-
Badania nowego czujnika wilgotności z filmem polimerowym
PublicationW pracy przedstawione zostały wyniki pomiarów widm impedancji czujników wilgotności z epoksydowymi filmami polimerowymi, zawierającymi czułe na wilgoć czwartorzędowe sole amoniowe. Filmy spreparowano z polietylenoiminy (PEI), usieciowanej przy pomocy eteru diglicydylowego 1,4-butanodiolu (BDDGE) z dodatkiem chlorku trójmetyloamoniowoglicydylowego (GTMAC).
-
Composite (La, Sr)MnO3-YSZ cathode for SOFC
PublicationW pracy przedstawiono właściwości elektryczne kompozytów (La,Sr)MnO3-YSZ. Materiały te dzieki swoim włąściwościom mogą staniwć dobry materiał na katody ogniw paliwowych. Przedstawiono też wyniki badań ogniwa paliwowego pracującego z paliwem wodorowym zbudowanego na bazie katody z kompozytu LSM-YSZ i anody Ni-YSZ. Uzyskano gęstośc mocy 0.26 W cm−2 przy temperaturze 850°C.
Year 2017
-
An electronic nose based on the semiconducting and electrochemical gas sensors
PublicationThe practical application of human nose for fragrance recognition is severely limited by the fact that our sense of smell is subjective and gets tired easily. Consequently, there is a significant need for an instrument that can be a substitution of the human sense of smell. Development of an electronic nose devices is an active area of research starting from pioneering research of Dodd and Persuad in the mid-1980s. Such systems...
-
Characteristics of La0.8Sr0.2Ga0.8Mg0.2O3-delta -supported micro-tubular solid oxide fuel cells with bi-layer and tri-layer electrolytes
PublicationIn this study, La0.8Sr0.2Ga0.8Mg0.2O3−δ (LSGM)-supported micro tubular solid oxide fuel cells (T-SOFCs) with two different configurations, one containing an LSGM–Ce0.6La0.4O2−δ (LDC) bi-layer electrolyte (Cell A) and one containing an LDC–LSGM–LDC tri-layer electrolyte (Cell B), were fabricated using extrusion and dip-coating. After optimizing the paste formulation for extrusion, the flexural strength of the dense and uniform LSGM...
-
Corrosion Study of Ceria Protective Layer Deposited by Spray Pyrolysis on Steel Interconnects
PublicationSingle fuel cells and electrolysis cells are assembled into stacks using interconnects in order to increase power and gas production capacity. The most common choice for the interconnect material is stainless steel. It has good electrical and mechanical properties and is also cost effective. One of the problems when using steel is the formation of a thermally grown oxide scale during use which has a lower electrical conductivity...
Year 2003
-
Analysis of the grain boundary conductivity for nanocrystalline doped ceria using the brick layer model.
PublicationW pracy przedstawiono wyniki badań elektrycznych i mikrostrukturalnych ceru domieszkowanego itrem. Gęste i nanokrystaliczne filmy przygotowane zostały z użyciem prekursorów polimerowych na szafirze. Konduktancja elektryczna była badana w funkcji temperatury syntezy, która jest skorelowana z wielkością ziaren. Otrzymano mniejszą konduktancję nanokrystalicznego filmu ceru w porównaniu z próbkami ceramicznymi.
-
Badania elektrokatalitycznego czujnika dwutlenku azotu.
PublicationW pracy opisano budowę i badania elektrokatalitycznego czujnika gazów skonstruowanego na bazie tlenku ceru domieszkowanego samarem. Elektrokatalityczne czujniki są stosunkowo nową grupą czujników gazu, w których wykorzystuje się kinetykę reakcji elektrochemicznej. Pokazano, że odpowiedź prądowo-napięciowa zależy od dwutlenku azotu.
-
Charakterystyki czujników wilgotności z dielektrykiem z porowatego tlenku glinu.
PublicationW pracy przedstawiono rezultaty badań charakterystyk ceramicznych czujników wilgotności z dielektrykiem z elektrolitycznie wytworzonego tlenku glinu.Pokazano wpływ doboru niektórych parametrów procesu elektro-katalitycznego na użytkowe charakterystyki czujników. Dokonano oceny dopasowania danych doświadczalnych, uzyskanych dla przedstawicieli dwóch grup czujników o różnych charakterystykach, do odpowiedzi dwóch znanych...
-
Comparison of anode and electrolyte support configuration of single- chamber SOFC.
PublicationW pracy przedstawiono wyniki badań jednokomorowych ogniw paliwowych SOFC, wytworzonych na podłożu z anody i elektrolitu. Użyto typowych materiałów wykorzystywanych do budowy dwukomorowych ogniw paliwowych SOFC: elektrolit - domieszkowany tlenek cyrkonu, anoda - cermet niklowo cyrkonowy, katoda - lantanian strontowo manganowy. Ogniwa były przygotowane w technologii odlewania ceramicznego i sitodruku. Parametry syntezy katody były...
-
Computer simulation of current voltage response of elektrocatalytic sensor.Optoelectronic and Electronic Sensors V.
PublicationW pracy przedstawiono wyniki symulacji komputerowej działania czujnika elektrokatalitycznego. Do badań wykorzystano program D. Gossera opierający się na metodzie różnic skończonych.
Year 2004
-
Anode supported single chamber solid oxide fuel cell in CH4-Air Mixture.
PublicationW tej pracy przedstawiono wyniki prac ogniw paliwowych na bazie elektrolitu z tlenku cyrkonu stabilizowanego itrem o grubości 1-2um wytworzonego na podłożu cermetu z tlenku niklu i tlenku cyrkonu stabilizowanego itrem. LSCF był wykorzystany jako katoda. Ogniwo paliwowe było testowane w konfiguracji jednokomorowej w mieszaninie powietrza i metanu. Uzyskano napięcie o wartości 0.8V, zaś moc wynosiła 0.12W/cm2. Zbdadano wpływ przepływu...
Year 2013
-
Application of wet powder spraying for anode supported solid oxide fuel cell with a perowskite SrTi0.98Nb0.02O3-d anode
PublicationAnode-supported solid oxide fuel cell with SrTi0.98Nb0.02O3–d anode, yttria-stabilized zirconia electrolyte and La(Ni0.6Fe0.4) O3d cathode has been successfully fabricated and evaluated. Process of anode support fabrication has been presented. Wet powder spraying and high temperature sintering method have been studied and applied to deposit the thin electrolyte layer.In order to improve catalytic properties of the anode, it has...
-
Badanie właściwości czujników wilgotności na bazie nanocząstek tlenku cynku
PublicationW celu pomiaru wilgotności szeroko stosowane są czujniki elektryczne. Warstwą czynną, zmieniającą swoje właściwości pod wpływem pary wodnej, stanowią najczęściej materiały ceramiczne lub polimerowe. Tlenek cynku jest jednym z materiałów ceramicznych będących dobrym kandydatem do zastosowania go jako warstwy czynną w czujnikach wilgotności. W tej pracy przedstawiono wyniki badań właściwości struktur czujnikowych z warstwą tlenku...
-
CGO FILMS ON YSZ ELECTROLYTE FABRICATED BY SPRAY PYROLYSIS FOR SOFC
PublicationINTRODUCTION Solid oxide fuel cells are one of the fastest developing energy converters. The advancement introduced by research community provides steady state progress is stability and performance of the fuel cells. Significant influence on the cell’s performance and stability is related to cell design. The simplest design just consists of an anode, a solid electrolyte and a cathode. However, in order to improve the properties,...
-
Characterization of CaTi0.9Fe0.1O3/La0.98Mg0.02NbO4 composite
PublicationA composite of CaTi0.9Fe0.1O3 and electrolyte material, i.e. magnesium doped La0.98Mg0.02NbO4 was prepared and studied. The phase content and the sample microstructure was examined by an X-ray diffraction method and scanning electron microscopy. EDS measurements were done both for composite samples and the diffusion couple. The electrical properties were studied by four terminal DC method. The Ahigh-temperature interaction between...
-
Chemorezystancyjny czujnik gazu na bazie polimeru przewodzącego PEDOT
PublicationPolimery przewodzące, takie jak Poli(3,4-etylenodioksytiofen) (PEDOT) są atrakcyjnymi materiałami elektrodowymi, które posiadają takie zalety, jak biokompatybilność, duża przewodność i elastyczność. Elektroprzewodzące polimery można otrzymać w wyniku chemicznej polimeryzacji lub elektropolimeryzacji. W niniejszej pracy przedstawiono zostanie koncepcja czujnika gazów składająca się z elektrody grzebieniowej oraz polimeru przewodzącego...
Year 2009
-
Applications of spin coating of polymer precursor and slurrysuspensions for Solid Oxide Fuel Cell fabrication
PublicationW pracy przedstawiono możliwości zastosowania w tlenkowych ogniwach paliwowych metody nanoszenia wirowego prekursorów polimerowych i zawiesin. Przedstawiono przykłady zastosowania tej metody do wytworzenia elektrolitu oraz warstw ochronnych dla stali nierdzewnych.
-
Conductivity improvement of Ce0.8Gd0.2O1.9 solid electrolyte
PublicationW pracy przedstawiono metodę zwieszenia przewoności domieszkowanego tlenku ceru wprowadzając podczas syntezy 2% wapnia. Zbadano metody wprowadzenia wapnia z użyciem prekursorów polimerowych. Uzyskano zwiększenie przewodności oraz syntezowalności elektrolitu stałego.
Year 2019
-
Badania tytanianu strontu podstawianego żelazem jako potencjalnego materiału katodowego dla tlenkowych ogniw paliwowych
PublicationW publikacji przedstawiono motywację podjętych badań nad podstawianymi żelazem tytanianem strontu do zastosowań w wysokotemperaturowych ogniwach paliwowych oraz ukazano wstępne wyniki badań elektrycznych oraz elektrochemicznych.
-
Copper and cobalt co-doped ceria as an anode catalyst for DIR-SOFCs fueled by biogas
PublicationThe nanocrystalline compounds of Co and Cu co-doped ceria (with up to 20 mol.% of dopants) were fabricated by the reverse microemulsion synthesis method. They were deposited in a form of layers on the surface of SOFC anode in an aim to act as electrochemically active materials for biogas reforming process. Fourier Transformed Infrared Spectroscopy was used to analyze a composition of outlet gases simultaneously with the tests of...
-
Deposition and Electrical and Structural Properties of La0.6Sr0.4CoO3 Thin Films for Application in High-Temperature Electrochemical Cells
PublicationLow-temperature deposition of electroceramic thin films allows the construction of new devices and their integration with existing large-scale fabrication methods. Developing a suitable low-cost deposition method is important to further advance the development of microdevices. In this work, we deposited a 1-lm-thick La0.6Sr0.4CoO3d (LSC) perovskite with high electrical conductivity on sapphire substrates at 400C and analyzed its...
Year 2012
-
Badanie przewodnictwa jonowego materiału katodowego do ogniw SOFC na bazie La1-xSrxMnO3-δ
PublicationMieszane przewodniki jonowo-elektronowe na bazie domieszkowanego manganianu lantanu znajdują powszechne zastosowanie m.in. jako elektrody w ogniwach paliwowych, czujnikach gazów lub jako warystory. Jednak wciąż niepoznane do końca mechanizmy występowania zjawiska mieszanego przewodnictwa sprawiają, że prace nad tymi materiałami wciąż trwają. Określenie składowej jonowej tego typu materiałów perowskitowych wymaga zastosowania...
-
Badanie właściwości czujnika elektrokatalitycznego na bazie tytanianu litowo-lantanowego
PublicationW pracy przedstawiono wyniki badań wpływu stężenie ditlenku azotu na kształt charakterystyk prądowo-napięciowych (I-V) nowego czujnika elektrokatalitycznego na bazie elektrolitu stałego z mobilnymi jonami litu LiLaTiO3. Czujnik ten został wykonany w technologii ceramicznej w formie pastylki z porowatymi elektrodami złotymi naniesionymi po obu jej stronach. Wykonano pomiary odpowiedzi czujnika w temperaturach 175ºC i 300ºC. Stężenie...
-
Conducting Polymer Microelectrodes Anchored to Hydrogel Films
PublicationArtykuł prezentuje wytwarzanie organicznych hydrożeli z mikroelektrodami poli(3,4-ethylenedioxythiophene, PEDOT), które wykazują obniżoną rezystywność 100 Ω/□. Proces przygotowania rozpoczyna się elektroosadzania przewodzącego PEDOT (ok. 20 S/cm) na mikroelektrodach Pt. Elektrolityczne wiąże się film PEDOT z hydrożelem. Tak wytworzona struktura jest odrywana elektrycznie pd podłoża.
-
Data analysis of FTIR spectra for study of outlet gases of Solid Oxide Fuel Cells fuelled by biogas
PublicationW pracy przedstawiono system umożliwiający połączenie spektroskopii FTIR z specjalnie zaprojektowanym oprogramowaniem w celu uzyskania informacji o stężeniach gazów wylotowych z ogniw paliwowych SOFC. Przebadane zostały główne produkty reformingu biogazu: tlenek węgla, dwutlenek węgla, metan oraz wodór. Opisane oprogramowanie umożliwia w prosty i szybki sposób uzyskanie informacji o gazach wylotowych ogniwa paliwowego.
Year 2018
-
Characteristics of La 0.8 Sr 0.2 Ga 0.8 Mg 0.2 O 3-δ -supported micro-tubular solid oxide fuel cells with LaCo 0.4 Ni 0.6-x Cu x O 3-δ cathodes
PublicationIn this study, micro-tubular solid oxide fuel cells (T-SOFCs) with extruded La0.8Sr0.2Ga0.8Mg0.2O3-δ (LSGM) electrolyte as the mechanical support and LaCo0.4Ni0.6O3-δ (LCNO) or LaCo0.4Ni0.4Cu0.2O3-δ (LCNCO) as cathodes were prepared and characterized. Partial substitution of Cu for the Ni-ion positions in the LCNO lattices was found to significantly enhance the densification and accelerate the grain growth. The porosity-corrected...
-
Characteristics of LaCo 0.4 Ni 0.6-x Cu x O 3-δ ceramics as a cathode material for intermediate-temperature solid oxide fuel cells
PublicationIn this study, the effects of Cu-ion substitution on the densification, microstructure, and physical properties of LaCo0.4Ni0.6-xCuxO3-δ ceramics were investigated. The results indicate that doping with Cu ions not only enhances the densification but also promotes the grain growth of LaCo0.4Ni0.6-xCuxO3-δ ceramics. The Cu substitution at x ≤ 0.2 can suppress the formation of La4Ni3O10, while the excess Cu triggers the formation...
-
Conducting polymer films for biodegradable metallic cardiovascular stents
PublicationIn recent years, there is increasing interest to create biodegradable metallic cardiovascular stents instead of using their permanent form. The most interesting materials for this purpose are iron and its alloys. However, in order to use it in clinical application, their degradation rate and biological performance need to be optimized. One promising solution is coating the metal with conducting polymer films. In this work, short...
Year 2011
-
Charakteryzacja warstw tlenkowych na stali 316L dla potzeb implantów biomedycznych
PublicationW pracy sprawdzony został wpływ warstw ochronnych na poprawę odporności korozyjnej stali 316L. Jako warstwy ochronne zastosowano materiał tlenku cyrkonu stabilizowanego itrem.
-
Coatings for improvement of high temperature corrosion resistance of porous alloys
PublicationPorowate stopy metaliczne są potencjalnymi podłożami nośnymi dla tlenkowych ogniw paliwo. Ich stosowanie obniża cenę ogniw paliwowych, co zaowocuje ich szybszą komercjalizacą. Jednak są one podatne na korozję w wysokich temperaturach. Dotychczas brak jest metod, które mogą poprawić rezystancję korozyjną porotawych stopów w wysokich temperaturach porowatych stopy do zastosowań SOFC. W tym artykule zaproponowano sposób na poprawę...
Year 2008
-
Chemical interaction between perovskite La0.6Sr0.4FeO3 and Super-Ionic Zr0.84Y0.16Ox
PublicationW pracy przedstawiono wyniki badań interakcji chemicznej pomiędzy materiałem perowskitowym LSF a materiałem superjonowym YSZ. Materiał superjonowy został wytworzony w niskiej temperaturze z użyciem prekusora polimerowego i zawiesiny proszku ceramicznego.W badaniach korzystano z spektroskopii rentgenowskiej.
Year 2020
-
Design and characterization of apatite La9.8Si5.7Mg0.3O26±δ-based micro-tubular solid oxide fuel cells
PublicationIn this study, electrolyte-supported (Cell A) and anode-supported (Cell B) micro-tubular solid oxide fuel cells (SOFCs) based on the La9.8Si5.7Mg0.3O26±δ (LSMO) electrolyte is built through an extrusion and dip-coating processes. The formulations and process conditions for these cells are established and optimized. Both cell configurations show no visible delamination or cracking, and reaction zones and inter-diffusion of any species...
seen 6739 times