Filters
total: 627
filtered: 547
Search results for: ALLOY
-
Structural and magnetic properties of Cu-alloyed FePd films
Publication -
The corrosion resistance of laser surface alloyed stainless steels
Publication -
Hydrogen degradation of high strength low alloyed steels.
PublicationBadano wpływ polaryzacji katodowej na własności stali węglowej, stali o podwyższonej i wysokiej wytrzymałości metodą stałego powolnego odkształcania.Stwierdzono, że stopień kruchości wodorowej każdej z badanych stali zależał od stężenia wodoru dyfuzyjnego.
-
The Effect of Increasing the Amount of Indium Alloying Material on the Efficiency of Sacrificial Aluminium Anodes
PublicationAl-Zn-In alloys having 4.2% zinc content and various indium content in the range of 0.02–0.2% were tested with respect to the most important electrochemical properties of sacrificial anodes in a cathodic protection, i.e., the current capacity and potential of the operating anode. The distribution of In and Zn in the tested alloys was mapped by means of the EDX technique, which demonstrated that these elements dissolve well in the...
-
The influence of laser alloying on the structure and mechanical properties of AlMg5Si2Mn surface layers
Publication -
Tuning the ferromagnetic phase in the CDW compound SmNiC2 via chemical alloying
PublicationWe report a study on tuning the charge density wave (CDW) ferromagnet SmNiC2 to a weakly coupled superconductor by substituting La for Sm. X-ray diffraction measurements show that the doped compounds obey Vegard’s law, where La (Lu) alloying expands (shrinks) the lattice due to its larger (smaller) atomic size than Sm. In the series Sm1−xLaxNiC2, CDW transition (TCDW =148K) for SmNiC2 is gradually suppressed, while the ferromagnetic...
-
Zirconium alloyed tungsten borides synthesized by spark plasma sintering
Publication -
Cavitation erosion of X5CrNi18-10 austenitic stainless steel alloyed with TiC
PublicationPraca prezentuje zmianę odporności kawitacyjnej stali X5CrNi18-10 po laserowym stopowaniu jej warstwy wierzchniej węglikiem TiC. Laserowe stopowanie przeprowadzono dla 2 wariantów. W pierwszym przypadku stal stopowano do zawartości 1,55 TiC a w drugim do zawartości 3,97% TiC. Uzyskane rezultaty wskazują że przy zawartości 3,97 TiC nastopiło znaczące zwiększenie odporności na plastyczne odkszyałcenie warstwy wierzchniej pod wpływem...
-
Superconductivity of Ta-Hf and Ta-Zr alloys: Potential alloys for use in superconducting devices
PublicationThe electronic properties relevant to superconductivity are reported for bulk Ta-Hf and Ta-Zr body centered cubic alloys, in a large part to determine whether their properties are suitable for potential use in superconducting qbits. The body centered cubic unit cell sizes increase with increasing alloying. The results of magnetic susceptibility, electrical resistivity, and heat capacity characterization are reported. While elemental...
-
Nickel alloys in hydroprocessing units
PublicationPrzedstawiono uszkodzenia stopu niklu typu 825 w wyniku eksploatacji w chłodnicy powietrznej za reaktorem wodorowym w rafineryjnej instalacji przepracowanych olejów napędowych. Wyjaśnono korozyjno-erozyjny mechanizm niszczenia, zwracając uwagę na kruchość materiału w obecności wodoru i udarowego działania strumieni procesowych.
-
The Influence of Laser Surface Alloying on the Thermal Fatigue Resistance of Hot Work Tool Steels
Publication -
Stainless Steels Sintered Form the Mixture of Prealloyed Stainless Steel and Alloying Element Powders
Publication -
The Erosion Resistance and Microstructure Evaluation of Laser Surface Alloyed Sintered Stainless Steels
Publication -
Effect of Different Vacuum Heat Treatments on the Microstructure of a Low Alloyed Sintered Steel
Publication -
Relationship between microstructure of laser alloyed of C45 steel and its cavitation resistance.
PublicationPrzedstawiono badania odporności kawitacyjnej stali C45 po laserowym stopowaniu jej powierzchni proszkami Mn., Ni, Cr, Nb, Mo, Co. Stwierdzono, że warstwa wierzchnia posiada wyższą odporność kawitacyjną jeśli w jej mikrostrukturze występuje pewna ilość austenitu zwiększająca podatność do wzmacniania odkształceniowego.
-
Relationship between microstructure of laser alloyed C45 steel and its cavitation resistance.
PublicationW pracy przedstawiono badania wpływu laserowo kształtowanej mikrostruktury na stali C45 po stopowniu różnymi kompozycjami proszków metali na własności kawitacyjne warstwy wierzchniej. Badania prowadzono w początkowym stadium erozji kawitacyjnej. Stwierdzono, że lepszą odporność kawitacyjną osiąga się gdy mikrostruktura jest podatna do umacniania odkształceniowego np. w obecności pewnej ilości austenitu w strukturze.
-
Emissivity Measurements on Shape Memory Alloys
Publication -
Structure and properties of magnesium cast alloys
Publication -
Surface modifications of ti and its alloys
PublicationThis article reviews the various surface modification techniques pertaining to titanium and titanium alloys including physical treatment, mechanical treatment, and chemical and electrochemical treatment. The proper surface modification expands the use of titanium and its alloys in the biomedical field for long-term implants retaining the excellent properties of substrate material and improving the specific surface properties required...
-
Random Microscopic Model of Quaternary Alloys
Publication -
Application and mechanical properties of aluminium alloys
PublicationThe paper presents a short survey of the application and mechanical properties of aluminium alloys. This area of scientific research is still developing, the authors restricted it to about 30 papers. Numerical simulations of the aluminium bracket are also investigated. The authors propose a solution to increase the load capacity of aluminium brackets with application of the additional cover plates. This study is proposed as an...
-
Cavitation erosion behavior of 18/8 stainless steel after its laser alloying of manganese
PublicationW pracy przedstawiono badania kawitacyjne stali austenitycznej 18/8 po laserowym stopowaniu jej powierzchni różną zawartością manganu. Oceniano podatnoś stopowanej powierzchni do odkształceniowego umacniania pod wpływem obciążeń kawitacyjnych oraz głębokość umocnienia.
-
Cavitation erosion behavior of 18/8 stainless steel after its laser alloying of manganese
PublicationW pracy przedstawiono wyniki badań własności kawitacyjnych stali nierdzewnej gatunku 18/8 po jej laserowym stopowaniu różną zawartością manganu. Stwierdzono, że przy zawartości Mn w ilości 7,13% występuje największy wzrost twardości po stopowaniu a głębokość umacniania na skutek działania obciążeń kawitacyjnych jest najmniejsza.
-
Enhanced formability and forming efficiency for two-phase titanium alloys by Fast light Alloys Stamping Technology (FAST)
Publication -
Multicomponent layers for aluminium alloys surface consolidation
PublicationThe main reason of the surface modification of the components such as pistons and cylinder blocks made of cast aluminium alloys is to obtain high hardness, wear and corrosion resistance of the working surface for larger lifetime of the motor-car and aircraft engines. In that aspect, the new conception of development - by hybrid method - of surface layers containing manganese, nitrogen, sulphur (Mn-N-S) and manganese, nitrogen,...
-
Hydrogen degradation of pre-oxidized zirconium alloys
PublicationThe presence of the oxide layers on Zr alloys may retard or enhance the hydrogen entry and material degradation, depending on the layer features. This research has been aimed to determine the effects of pre-oxidation of the Zircaloy-2 alloy at a different temperature on hydrogen degradation. The specimens were oxidised in laboratory air at 350°C, 700°C, and 900°C. After, some samples were tensed at 10-5 strain rate and simultaneously...
-
Hydroxyapatite coatings on porous ti and ti alloys
PublicationDeposition of hydroxyapatite coating on porous Ti and Ti alloys with electrochemical and biomimetic deposition approach is presented. The enhancement of phosphates deposition by well oriented and uniform titanium oxide nanotube array on the surface of titanium substrate is discussed.
-
Dynamical properties of ordered Fe–Pt alloys
Publication -
Application of Shape Memory Alloys in Pipeline Couplings for Shipbuilding
PublicationThe aim of the study is to analyse shape memory alloy (SMA) pipeline joints in limited space applications for all kinds of ships. Generally, the space available in various areas on ships is strictly limited and service works usually meet many obstacles. If we consider a pipeline, the flange joints always require a larger free space around the pipe than the pipe alone. A simultaneous problem can occur with the propeller shaft line...
-
High temperature corrosion and corrosion protection of porous Ni22Cr alloys
PublicationIn this work corrosion kinetics of the porous IN625 alloy is studied in the temperature range of 700 °C – 800 °C in air and humidified hydrogen for up to 1000 hours. Moreover, an effective and simple method of reducing corrosion rates of porous alloys by the infiltration of the rare earths elements is shown. Modification by the yttrium containing precursor reduces the corrosion rate by a factor of 50 in air at 700 °C so that the...
-
Surface Layer Properties of Sintered Ferritic Stainless Steel Remelted and Alloyed with FeNi and Ni by HPDL Laser
Publication -
Analysis of the Surface Stereometry of Alloyed Austenitic Steel after Fibre Laser Cutting using Confocal Microscopy
PublicationThe paper extends the concept of cut edge quality and examines the fibre laser cutting process. A Prima Power Platino Fiber Evo device with a reference speed (RS) of 3500 mm/min was used for laser cutting. In order to analyse the influence of the laser cutting speed on the cut edge quality of X5CrNi18-10 stainless steel sheets, macroscopic studies were conducted on a stereoscopic microscope and surface stereometry on a confocal...
-
Stable nanoconjugates of transferrin with alloyed quaternary nanocrystals Ag–In–Zn–S as a biological entity for tumor recognition
PublicationOne way to limit the negative effects of anti-tumor drugs on healthy cells is targeted therapy employing functionalized drug carriers. Here we present a biocompatible and stable nanoconjugate of transferrin anchored to Ag-In-Zn-S quantum dots modified with 11-mercaptoundecanoic acid (Tf-QD) as a drug carrier versus typical anticancer drug, doxorubicin. Detailed investigations of Tf-QD nanoconjugates without and with doxorubicin...
-
Effect of Indium on the Properties of Mg-Zn-Based Alloys
Publication -
Advances in Sheet Metal Forming Processes of Lightweight Alloys
Publication -
Some aspects of laser surface remelting of aluminium alloys
PublicationPodano podstawy procesu przetapiania laserowego stopów aluminium. Opisano rezultaty elektrochemicznych badań korozyjnych dla stopu AlSi13Mg1CuNi i porównano je ze stanem wyjściowym stopu.
-
Laser surface treatment of aluminium alloys at cryogenic conditions.
PublicationPrzedstawiono nową metodę obróbki laserowej powierzchni stopów aluminium w warunkach kriogenicznych. W wyniku tej obróbki w warstwie wierzchniej stopów przeznaczonych na tłoki silników spalinowych uzyskano znaczące podwyższenie twardości, odporności na zużycie ścierne oraz wzrost właściwości korozyjnych.
-
Low Current Transformer Utilizing Co-Based Amorphous Alloys
PublicationMetal oxide surge arresters have been widely used for protection of power system networks against overvoltages due to atmospheric discharges or malfunction of devices connected to the network. During its operation a surge arrester structure is degradated, what can be observed as an increase of a surge arrester leakage current. Paper presents an implementation of a new, high-permeability, Co64Fe4Ni1Si15B14 amorphous alloy as a current...
-
Low current transformer utilizing Co-based amorphous alloys
PublicationMetal oxide surge arresters have been widely used for protection of power system networks against overvoltages due to atmospheric discharges or malfunction of devices connected to the network. During its operation a surge arrester structure is degradated, what can be observed as an increase of a surge arrester leakage current. Paper presents an implementation of a new, high-permeability, Co64Fe4Ni1Si15B14 amorphous alloy as a current...
-
Environmental degradation of Ti alloys in artificial saliva and a role of fluorides
PublicationThe titanium and its alloys are potentially prone to hydrogen embrittlement, including those proposed for dental implants. The research has been aimed to assess a susceptibility to environment-enhanced degradation of the Ti-13Zr-13Nb alloy in artificial saliva with or without hydrofluoric acid, subject or not to cathodic polarisation. The results have shown that even if artificial saliva is safe environment, both cathodic polarization...
-
Anodized multi – component titanium alloys carrying antibacterial features
Publication -
The Influence of Casein Coatings on the Corrosion Behavior of Mg-Based Alloys
Publication -
Coatings for improvement of high temperature corrosion resistance of porous alloys
PublicationPorowate stopy metaliczne są potencjalnymi podłożami nośnymi dla tlenkowych ogniw paliwo. Ich stosowanie obniża cenę ogniw paliwowych, co zaowocuje ich szybszą komercjalizacą. Jednak są one podatne na korozję w wysokich temperaturach. Dotychczas brak jest metod, które mogą poprawić rezystancję korozyjną porotawych stopów w wysokich temperaturach porowatych stopy do zastosowań SOFC. W tym artykule zaproponowano sposób na poprawę...
-
Pitting corrosion of Al-Mg alloys in chloride containing media
PublicationStopy aluminium znajdują coraz szersze zastosowanie w instalacjach przemysłowych, stosownie do ich ciekawych właściwości fizyko-chemicznych oraz mechanicznych. Niska gęstość, wygląd, odporność korozyjna i dobry stosunek gęstości do odporności mechanicznej. W pracy porównano odporność korozyjną stopu aluminium 5182 zawierającego ok. 4,5% Mg ze stopem stanowiącym "handlowo czyste aluminium" - 1100. Stwierdzono przydatność dynamicznej...
-
Manganese-nitrogen-sulphur surface layers produced on aluminium alloys
PublicationPodano metodę wytwarzania warstw powierzchniowych zawierających mangan, azot i siarkę na odlewniczym stopie aluminium. Przedstawiono mikrostrukturę przekroju i powierzchni wytworzonych warstw, ich twardość oraz wlaściwości tribologiczne i korozyjne.
-
Dependence of cavitation performance of superficial iron alloys on the sub-strate
PublicationWykazano zależność odporności kawitacyjnej laserowo wytworzonych i elektrodąotuloną napawanych powłok od rodzaju podłoża. Napoiny wykonywano na stali 45, 2H13, 0H18N9 i na żelazie Armco.
-
Effects of the time and temperature on the oxide scale formed on the cobalt alloys
PublicationWarstwy wykonane za pomocą techniki PTA ze stopu kobaltu poddano utlenianiu w różnych temperaturach i w różnym czasie. Mikrostruktury otrzymane po utlenianiu wskazują na proces degradacji materiału. Proces ten prowadził do degradacji obszarów międzydendrytycznych napoiny. Skład chemiczny powstającej zgorzeliny byłzależny od temperatury utleniania, składu chemicznego stopu, ze szczegfólnym uwzględnieniem obecności małych ilości...
-
Self-Organized Nanotubular Oxide Layers on Ti and Ti Alloys
PublicationTo improve bioactivity of titanium and titanium, the implant surface modification by formation of self-organized TiO2 nanotube arrays with electrochemical techniques is presented. The influence of electrolyte composition and deposition parameters during anodization is characterized. The enhancement of phosphates deposition by titanium nanotubular structure is discussed. The calcium phosphate ceramics is shown to be uniformly deposited...
-
Effect of double thermal and electrochemical oxidation on titanium alloys for medical applications
PublicationThe research focuses on the development and characterization of innovative thin hybrid oxide coatings obtained in subsequent processes of thermal (TO) and electrochemical (EO) oxidation. Four different surface modifications were investigated and the microstructure was determined, the mechanical, chemical and biological properties of the Ti-13Nb-13Zr alloy were assessed using scanning electron microscopy, X-ray dispersion analysis,...
-
Structure and properties of liquid Al–Cu alloys: Empirical potentials compared
PublicationWe report on the structure and mass transport properties of liquid Al–Cu alloys predicted by two recently-developed empirical many-body potentials: MEAM (Jelinek et al., 2012) and EAM-ADP (Apostol and Mishin, 2011), and by the well-known Gupta potential. Total and partial pair correlation functions, angular distribution functions, densities, coordination numbers and self-diffusion coefficients are compared with published experimental...