Search
Search results for: AIRBORNE PARTICLES,STUDDED TYRES,CONCRETE ROAD,WEAR
-
A pin-on-disc study of airborne wear particle emissions from studded tyre on concrete road contacts
PublicationStudded tyres wear surfaces of winter roads, generating inhalable airborne particles. In this study, four concrete road materials and two stud geometries were investigated in terms of wear, road material hardness and airborne particle concentration. The sliding contact between studded tyres and road materials was studied using a pin-on-disc machine in a clean chamber. The results show that the normal load and the stud size have...
-
The importance of the bottom layer in double-layer porous asphalt for noise reduction
PublicationDouble-layer porous asphalt concrete (DPAC) surfaces are generally considered to be the acoustically most effective low noise road surfaces ready for implementation. While DPAC used on highways in warm climates may have an average life of around 8 years, in Scandinavia with severe winter climate DPAC usually survive only about 3 years; partly due to wear of studded tyres. An ongoing project in Sweden, applying DPAC and single-layer...
-
The best porous asphalt pavement in Sweden so far
PublicationIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed in various versions on the E4 motorway through the Swedish city Huskvarna. As a result of a court decision the Swedish Transport Administration had to reduce noise emission by applying a low noise road surface that would reduce A-weighted noise levels by 5 dB, as an average. Earlier experience in Sweden indicated that it was possible to obtain a high...
-
Effective density of airborne wear particles from car brake materials
PublicationPeople living in urban environments are subject to high health risks due to various anthropogenic sources of airborne particulate matter, including wear of transport vehicle brakes. Studies of airborne particles often require an estimate of the effective particle density, a property that allows correct matching of mass and size characteristics measured by different aerosol instruments. In this study we investigated the effective...
-
A Study on Emission of Airborne Wear Particles from Car Brake Friction Pairs
PublicationThe emission of airborne wear particles from friction material / cast iron pairs used in car brakes was investigated, paying special attention to the influence of temperature. Five low-metallic materials and one non-asbestos organic material were tested using a pin-on-disc machine. The machine was placed in a sealed chamber to allow airborne particle collection. The concentration and size distribution of 0.0056 to 10 μm particles...
-
Poroelastic Road Surfaces - State of The Art
PublicationPoroelastic Road Surfaces (PERS) constitute a specific group of pavements containing a great amount of crumbled rubber. In most cases rubber aggregate constitutes about 20% of the mixture (by weight) and a polyurethane resin is used as a binder. As a result, PERS is characterized by a much higher elasticity than asphalt and a high porosity typical for drainage pavements. Due to this, tire/road noise is greatly reduced and on top...
-
Tyre/road noise of passenger car tyres, including tyres for electric vehicles - road measurements
PublicationThe paper presents the results from CPX measurements of tyre/road noise performed for selected passenger car tyres, including the tyres especially designed for electric vehicles. The tyres have been measured when rolling on several typical road surfaces in Norway and in Poland. In addition, the tyres have been measured on some very low noise road surfaces, such as a the poroelastic road surface (PERS). The measurement results...
-
Emission and properties of airborne wear particles from train brake friction materials based on novolac phenolic resins and butadiene rubbers
PublicationThe emission of airborne particulate matter from a train brake depends on the formulation of its friction material. This study investigates the emission and properties of wear particles from train brake friction materials based on straight or resorcinol-modified novolac phenolic resin and nitrile or styrene butadiene rubber used as binding ingredients. The wear particles are generated by a pin-on-disc tribomachine inside an aerodynamic...
-
Quantification of ultrafine airborne particulate matter generated by the wear of car brake materials
PublicationThe wear of car brakes is one of the main sources of airborne particulate matter in urban environments. Ultrafine wear particles are of special environmental interest since they can easily penetrate the human body through inhalation and cause various diseases. In the present study, the contribution of ultrafine particles to airborne particulate matter emitted from car brake materials was investigated under different friction conditions....
-
Correlations between the wear of car brake friction materials and airborne wear particle emissions
PublicationAirborne wear particles emitted from transport vehicle brakes are one of the main sources of toxic metals in inhalable particulate matter. Prediction of wear particle emissions may become more accurate if the relationship between the wear and particle emission characteristics is known. An experimental study was performed to investigate proportional correlations between the mass wear, 0.01–0.42 μm particle emission measured by a NanoScan...
-
Temperature influence on tyre/road noise of selected tyres
PublicationAir and road temperatures substantially affect road vehicle noise emission. The temperature influence on tyre/road noise depends mainly on tyre-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tyres. The correction procedures for temperature effect are still under consideration and preparation. Tyre/road noise measurements using CPX method were performed...
-
The Application of Fibres from Recycled Postconsumer Tyres for Concrete Reinforcement
PublicationPoland as a Member State is obliged to implement the EU specific environmental legislation focused on the reduction, transport and treatment of waste. The Landfill Directive prohibited the landfilling of whole tyres and their by-products. Although the EU Directive of Waste limits the use of tyres as secondary fuel, Poland is still the EU leader in burning tyres in cement kilns. Post-consumer tyres are utilised in a number of...
-
Emission of 1.3–10 nm airborne particles from brake materials
PublicationOperation of transport vehicle brakes makes a significant contribution to airborne particulate matter in urban areas, which is subject of numerous studies due to the environmental concerns. We investigated the presence and number fractions of 1.3–10 nm airborne particles emitted from a low-metallic car brake material (LM), a non-asbestos organic car brake material (NAO) and a train brake cast iron against a cast iron. Particles...
-
Airborne wear particle emission from train brake friction materials with different contents of steel and copper fibres
PublicationThis study investigated the influence of the amount of steel and copper fibres in a train brake friction material on the tribological performance, emission intensity and characteristics of airborne wear particles. The particles were generated on a pin-on-disc tribometer under controlled friction and environmental conditions. It was found that the steel fibre results in a more intensive emission of 0.3–10 μm particles compared to...
-
Porosity and shape of airborne wear microparticles generated by sliding contact between a low-metallic friction material and a cast iron
PublicationThe wear of brakes in transport vehicles is one of the main anthropogenic sources of airborne particulate matter in urban environments. The present study deals with the characterisation of airborne wear microparticles from a low-metallic friction material / cast iron pair used in car brakes. Particles were generated by a pin-on-disc machine in a sealed chamber at sliding velocity of 1.3 m/s and contact pressure of 1.5 MPa. They...
-
Potential reduction of traffic noise by the means of increased fleet of electric vehicles using a combination of low-noise tyres and low-noise road surfaces
PublicationIn the future, the number of zero-emission vehicles like electric and plug-in hybrid vehicles (in electric mode) is expected to be a substantial part of the vehicle fleet. In Norway, such vehicles already account for approximately 20 % of all new cars sold. Since these vehicles emit negligible noise related to the power-train, the tyre/road noise is the dominating noise source. In the LEO project, tyres designed for such cars have...
-
Concrete versus green corridors in road planning. Gdansk case
PublicationThe aim of an article is to present the threats which may be caused by the construction of the transit road inside the city structure, and some mitigation measures aiming to eliminate or minimize environmental and landscape damages and social problems. Theoretical guidelines and conclusions will be followed by the example illustrating the problem. As an answer, some guidelines enabling sustainable road planning will be presented....
-
Numerical simulation of the influence of the selected factors on the performance of a concrete road barrier H2/W5/B
PublicationThis paper discuss the influence of selected factors on the performance of a concrete road barrier H2/W5/B. Modelling techniques of a concrete road safety system were briefly discussed. Comparison to the full scale crash test results has been shown. The concrete road safety barrier has been investigated for evaluation of the overall damage after collision under various initial conditions. The failure assessment criterion has been...
-
Fibres from recycled post-consumer tyres for concrete reinforcement
PublicationW pracy przedstawiono aktualną sytuację dot. wykorzystania drutu stalowego z recyklingu opon samochodowych. Przedstawiono wyniki badań przeprowadzonych w laboratorium Katedry Konstrukcji Betonowych i Technologii Betonu nad zastosowaniem włókien stalowych z recyklingu do zbrojenia betonu. Otrzymane wyniki porównano z próbkami fibrobetonu uzyskanego na bazie przemysłowo produkowanych włókien stalowych.
-
Analysis of airborne metal containing particles with EDX/EDS detectorsin electron microscopes
PublicationIn years 2006-2010 particulate matter analysis was undertaken for dust samples collected from Gdansk and London area in orderto compare their morphology and composition. Part of those studies was devoted to analysis of particulate matter (PM) bearingmetals. Characterization of the morphology and size of the particles collected onto the filters was performed using a scanning electronmicroscope (SEM) and transmission electron microscope...
-
Noise and Rolling Resistance Properties of Various Types of Winter Tyres Compared to Normal Car Tyres
PublicationTo cope with winter weather conditions, potentially including snow and ice, it is common to use winter tyres, or ”all-seasons” tyres assumed to be safe both in summer and winter. In some northern countries, winter tyres are mandatory. Traditionally, it has been assumed that winter tyres are noisier than normal tyres (here called summer tyres) and winter tyres equipped with studs are assumed to be very noisy.This paper presents...
-
The influence of road surface unevenness on tyre rolling resistance
PublicationThe geometric characteristics of road surface substantially affect the interaction between tyre and road. Depending on pavement texture wavelength, the texture chiefly affects tyre/road friction, rolling resistance, interior and exterior noise, tyre wear, and ride comfort. The article presents results of investigations on the influence of road surface unevenness on the rolling resistance of passenger car and truck tyres. The tests...
-
Poroelastic Low Noise Road Surfaces
PublicationNoise is one of the most important problems related to road traffic. During the last decades, noise emitted by engine and powertrain of vehicles was greatly reduced and tyres became a clearly dominant noise source. The paper describes the concept of low noise poroelastic road surfaces that are composed with mineral and rubber aggregate bound by polyurethane resin. Those surfaces have a porous structure and are much more flexible...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublicationThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Road texture influence on tyre rolling resistance
PublicationTyre performance, one of the critical factors for vehicle users, is strongly related to theroad surface characteristics, most notably to the pavement texture. Phenomena that occur at the tyre/road interface affect tyre friction (skid resistance), rolling resistance, tyre wear and tyre/road noise. This article deals with relationship between surface texture and rolling resistance of light and heavy vehicle tyres. Mean profile depth...
-
A concept for reducing PM 10 emissions for car brakes by 50%
PublicationWith regard to airborne particles with an aerodynamic diameter of less than 10 μm (PM10), in countries in the European Union, the mass of brake emissions equals approximately 8–27% of the total traffic-related emissions. Using a research methodology combining tests at different scale levels with contact mechanics simulations and PM10 chemical characterization, the REBRAKE EU-financed project had the following aims: i) to demonstrate...
-
INFLUENCE OF MEASURING CONDITIONS ON TYRE/ROAD NOISE
PublicationA decisive factor for the development of tyres and road surfaces is the ability to conduct representative and reproducible measurements of selected characteristics related to the interaction of tyres and road surfaces. In terms of tyre/road noise measurements in Europe two methods described in ISO/FDIS 11819-2 and ECE Regulation No.117 are used. The latter is compulsory for assigning the tyre noise labels. The methodologies differ...
-
Tyre/road noise reduction by a poroelastic road surface
PublicationLow noise road surfaces of existing types may in favourable cases and in new conditions provide up to 7 dB of noise reduction. For higher noise reductions, innovative solutions must be sought. Poroelastic road surfaces (PERS) may be such a solution, which currently is studied in the EU project PERSUADE. This paper presents results of trials with a PERS version prefabricated by one of the project partners. Tests were made in a laboratory...
-
Reduction of road traffic noise by source measures — present and future strategies
PublicationThe current trend worldwide is less focused on reducing road traffic noise. This is in strong contrast to the severe impact of traffic noise to the general health and quality of life. A more holistic and combined strategy is needed. Current international rules and regulations regarding vehicles and tyres are not sufficient to reduce traffic noise levels in an effective way. Calculations show that these regulations will only yield...
-
Acoustic lifecycle study of the double-layer porous asphalt on E4 in Huskvarna, Sweden
PublicationIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed on the E4 motorway through the Swedish city Huskvarna. Earlier experience in Sweden indicated that it was feasible to obtain a high initial noise reduction but due to the widespread use of studded tires in winter, clogging and ravelling created losses of around 2 dB per year, with an expected acoustical lifetime of only 3 years. However, the improved...
-
Tyre rolling resistance and its influence on fuel consumption
PublicationRolling resistance of tyres is one of the major resistive forces acting on any wheeled vehicle. Unfortunately, it is also one of the forces very difficult to measure. It is estimated that in certain traffic conditions (like for example constant speed driving with slow or moderate speed) so called Rolling Resistance Impact Factor may be as high as 0.3. This means that reduction of rolling resistance by 50% would lead to 15% of energy...
-
INFLUENCE OF LOAD AND INFLATION PRESSURE ON THE TYRE ROLLING RESISTANCE
PublicationTyre load and inflation pressure are important factors controlling rolling resistance of road vehicles. The article presents results obtained in the Technical University of Gdańsk during laboratory and road measurements of different car tyres rolling on different pavements. The knowledge of rolling resistance characteristics is important for modelling car dynamics as well as fuel consumption. It is also necessary to establish proper...
-
Further development of the poroelastic road surface within the new Polish project SEPOR
PublicationRoad surfaces have a direct impact on noise generated by rolling tyres, the main and dominant source of noise of moving vehicles. Road surface texture, porosity and stiffness/elasticity govern the pavement contribution to tyre/road noise the most. An experimental PoroElastic Road Surface (PERS) is a wearing course with a high content of interconnected voids (pores) and with an elastic behavior due to the use of small particles...
-
Degradation of reference tyres used for CPX measurements
PublicationMeasurements of tyre/road noise using the Close Proximity Method are based on reference tyres that are described in ISO/TS 11819-3. The standard specifies two tyres, namely "P1" and "H1" that should be used during measurements. To be used for measurements each tyre must fulfill certain conditions that are listed in the standard. The conditions are related to the tread pattern depth and rubber hardness. During experiments performed...
-
Comparison of pavement noise properties on selected road sections using different CPX measuring systems: self-powered vehicle and special test trailer
PublicationThe recently published ISO standard intended to measure the noise properties of road surfaces in a standardized method (ISO 11819-2:2017) precisely defines measurement procedure of the influence of road surface on traffic noise. According to it, two types of test vehicles may be utilized: a self-powered vehicle fitted with one or more test tyres and a trailer towed by a separate vehicle with one or more test tyres mounted on the...
-
INFLUENCE OF TEST CONDITIONS ON TYRE/ROAD NOISE MEASURED BY THE DRUM METHOD
PublicationTyre/road noise is one of the most important environmental problems related to road traffic. Nowadays a few standard procedures of tyre/road noise measurements are in use. Unfortunately, measurement conditions specified within relevant standards are very different. For example, procedure described in ISO 11819-2 used for pavement investigations requires tyre load of 3200 N and capped inflation pressure of 200 kPa. At the same time...
-
Improving the CPX method by specifying reference tyres and including corrections for rubber hardnes and temperature
PublicationRecently completed work in the EU project ROSANNE and in working group ISO/TC43/SC1/WG33 has allowed substantial improvements to measurements made by the Close-Proximity (CPX) method, intended for measurement of noise properties of road surfaces.The paper summarizes the experimental work and describes the conclusions and implementation in ISO/FDIS 11819-2 (CPX method) and in the supporting ISO (draft) Technical Specifications 11819-3...
-
Sliding bearings with sintered bronze bush lubricated by contaminated water with solid particles – Theoretical and experimental studies
PublicationSliding journal bearings lubricated with water coming directly from the environment are a solution used in shipbuilding, pumps and hydropower. However, the working fluid or surrounding water cannot always be filtered because of design limitations, which often causes the problem of premature wear of these sensitive bearings. The research conducted made it possible to assess the wear of sliding bearings lubricated with water containing...
-
INFLUENCE OF TEMPERATURE ON THE TYRE ROLLING RESISTANCE
PublicationTemperature is a very important factor controlling rolling resistance of road vehicle tyres. There are at least three different temperatures that may be considered as important factors controlling thermal conditions of the rolling tyre. The most common measure of the thermal conditions during tyre rolling is ambient air temperature. The other two are: pavement temperature and “tyre” temperature. Tyre temperature is the most difficult...
-
Influence of permanent magnetic field on wear performance of dry sliding contacts
PublicationResults of experimental studies concerning the influence of permanent magnetic field on wear of dry sliding contact are presented.It was found that magnetic field of horizontal orientation is causing temporary reduction of material's hardness. It also facilitates and accelerates removal process of wear particles from the contact zone.Formation of bulges, consisting of accumulated and compacted anti-ferromagnetic material produced...
-
The EU Tyre Noise Label: The problem with measuring the noise level of only a few of all tyre variants
PublicationThe STEER project, described in another Inter-Noise 2022 paper, has evaluated the performance of the noise label of the European tyre label. The major finding was that uncertainties of the tyre/road noise measurements were higher than should be accepted. One of the worst uncertainty sources was found to be the common practice to measure only some tyres of all sizes or variants within a tyre line, to save money. Generally, only...
-
DESIGN AND CALIBRATION OF ROLLING RESISTANCE TEST TRAILER R2mk.2
PublicationThe paper describes construction nad calibration procedures of the rolling resistance test trailer R2 Mk2. The trailer is design to measure rolling resistance of passenger car tyres in various road conditions on trafficked road. The trailer utilizes so called angle method also known as vertical arm method. The paper presents also calibration procedures that are necessary to ascertain good precision of the measurements.
-
Research on operational characteristics of tyres with run flat insert
PublicationThe paper describes results of research on heavy vehicle tyre with Run Flat VFI insert. The experiment has included the determination of heat generation, rolling resistanceand radial stifnessof two different tyre designes (textile and steel carcass). The results have been used for the purpose of ewalution of tyre operating characteristics. The study included research on non-inflated tyre properties. The purpose of the paper is...
-
Comparison of road and laboratory measurements of tyre/road noise
PublicationTyre/road noise is one of the major environmental problems related to road traffic. There are several measuring methods of tyre/road noise that may be carried out on the road (for example Coast-down and Close Proximity Method) or in the laboratory (Drum Method). Road measurements are preferred for evaluations of pavement properties while laboratory methods are mostly used to evaluate tyres. One of the biggest problems associated...
-
Noise Generated by Tyres Designet for Electric Vehicles - Results of Laboratory Experiments
PublicationA few years ago, electric and hybrid vehicles were rarely seen on public roads and were considered more as exotic curiosities or even as a sign of extravagance than a practical means of transport. Nowadays the situation has changes significantly. This was caused both by the technical development and legislative actions, as well as the organizational nature promoting the purchace and use of low emission vehicles. Electric vehicles...
-
Tyre/road noise reduction of poroelastic road surface tested in a laboratory
PublicationA so-called poroelastic road surface (PERS) is being developed in Europe. This contains a large percentage of rubber particles mixed with hard aggregate (stone and sand) and bound with polyurethane. This gives high air void content (around 30 %), high elasticity and smooth texture, all of which should give low noise properties. Inthis experiment anominally 30 mm thick sample of PERS was mounted on a steel drum. Various car tyres...
-
Relieving the Measuring System of the Trailer for Tyre/Road Rolling Resistance Measurements from the Inertia Force
PublicationIn the article the principle of measuring of tyre/road rolling resistance tyres in road conditions applied in a special measuring trailer is presented. This trailer was built in Faculty of Mechanical Engineering at Gdansk University of Technology. The construction of two special devices used in this trailer was discussed. These devices eliminate the influence of some chosen confounding measurements factors such as: the inertia...
-
Effect of coarse grain aggregate on strength parameters of two-stage concrete
Publication. Two-stage concrete (TSC) is a special type of concrete that the method of its construction and implementation is different from conventional one. In TSC, coarse aggregate particles are first placed in the formwork and voids between them are subsequently injected with a special cementations mixture. TSC has been successfully used in many applications, such as underwater construction, casting concrete sections congested with reinforcement...
-
Optimization of Single-Sided Lapping Kinematics Based on Statistical Analysis of Abrasive Particles Trajectories
PublicationThe chapter presents the influence of selected kinematic parameters on the geometrical results of the single-sided lapping process. The optimization of these parameters is aimed at improving the quality and flatness of the machined surfaces. The uniformity of tool wear was assumed as main optimization criterion. Lapping plate wear model was created and in detail was analyzed. A Matlab program was designed to simulate the abrasive...
-
Karol Grębowski dr inż.
PeopleKarol Grębowski (M.Sc.) works as an assistant at the Department of Technical Fundamentals of Architecture Design of the Faculty of Architecture at Gdansk University of Technology. His scientific research deals with dynamic phenomena occurring during the vibration of structures, bridges, and studies the design methodology of the elements forming passive protection system of the vehicles degraded by struck or explosion in the context...