displaying 1000 best results Help
Search results for: SHIPPING NOISE
-
Analysis and Optimization of Noise in Continuous-Time OTA-C Filters
PublicationW pracy przedstawiono ogólną procedurę analizy szumów w filtrach klasy OTA-C czasu ciągłego. Procedura umożliwia analizę filtrów o dowolnej topologii i dowolnego rzędu w ramach rozważanej klasy. W oparciu o opis macierzowy ogólnej struktury filtru OTA-C wyprowadzono ogólne formuły pozwalające na wyznaczanie i optymalizację szumów dowolnego filtru OTA-C. Przedstawione wyniki są użyteczne nie tylko dla klasycznych (dyskretnych lub...
-
Resistance Noise Higher-Order Spectrums in Nanoparticle Gas Sensors.
PublicationPrzedstawiono badania fluktuacji rezystancji sensora gazu wykonanego z nanocząstek WO3. Stwierdzono występowanie składowych o rozkładzie prawdopodobieństwa różnym od rozkładu Gaussa. W celu zwiększenia czułości i selektywności wykrywanych gazów zastosowan do analizy obserwowanych fluktuacji spektra wyższych rzędów.
-
Directivity of tire/road noise emission for selected tires and pavements
PublicationPraca pośwoęcona jest kierunkowości emisji hałasu opon i nawierzchni drogowych. Opony są dominującym źródłem haasu w pojaździe poruszającym się w typowych warunkach ruchu drogowego. Hałas ten nie jest bezkierunkowy jak to przyjmuje się w modelach obliczeniowych hałasu. Takie założenia wynikają z ograniczonej dostępności danych dotyczących kierunkowości i mogą prowadzić do niedokładności przy prognozowaniu hałasu drogowego. Praca...
-
An improved frequency estimator for an adaptive active noise control scheme
PublicationAn improved frequency tracker is proposed for the recently introduced self optimizing narrowband interference canceller (SONIC). The scheme is designed for disturbances with quasi-linear frequency modulation and, under second-order Gaussian random-walk assumption, can be shown to be statistically efficient. One real-world experiment and several simulations show that a considerable improvement in disturbance rejection may be achieved...
-
Dedicated power supply subsystem for ultra-low noise preamplifiers
PublicationIn field of electronics there is need for low-noise amplifiers. Noise have the most important influence on analog circuits. Therefore exist necessity to develop new ultra-low noise power supplies, which can cooperate with specified amplifiers and preamplifiers. It is very common that professional power supplies are very expensive and still have disadvantages. This paper proposes simple and inexpensive solution, which fulfill specific...
-
Fast clutter cancellation for noise radars via waveform design
PublicationCanceling clutter is an important, but very expensive part of signal processing in noise radars. It is shown that considerable improvements can be made to a simple least squares canceler if minor constraints are imposed onto noise waveform. Using a combination of FPGA and CPU, the proposed scheme is capable of canceling both stationary clutter and moving targets in real-time, even for high sampling rates.
-
Temperature influence on tire/road noise evaluated by the drum method
PublicationAmbient air and road surface temperatures substantially affect the road vehicle noise emission. The temperature influence on tire/road noise depends mainly on tire-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tires. The correction procedures for temperature effect are still under consideration and preparation. Laboratory experiment was prepared to...
-
Reduction of noise and rolling resistance by horizontal grinding of asphalt pavements
PublicationGrinding of cement concrete pavements to reduce unevenness and noise is common since a long time. Grinding is then made with wheels equipped with diamond blades rotating in the vertical plane. This creates narrow vertical/longitudinal grooves in the pavement. It is not applied to asphalt pavements. In this paper an alternative type of grinding is studied. In this case plates with diamond heads rotate in the same plane as the pavement,...
-
Irregular variations in GPS time series by probability and noise analysis
Publication -
Cheap Cancellation of Strong Echoes for Digital Passive and Noise Radars
PublicationThe problem of cancellation of strong, potentially nonstationary,echoes in noise radars and passive radars utilizing digitaltransmissions is considered. The proposed solution is a multi-stage procedure.Initial clutter estimates, obtained using the least mean squares(LMS) algorithm, are refined using specially designed filters, "matched"to spectral densities of targets and clutter. When the postprocessing filtersare noncausal, the...
-
Some aspects of noise generated by a small ship in the shallow sea
PublicationThe passing and underwater moving objects produce the noises of variable intensity, which significantly increase the overall level of noise in the sea. This applies to both the sonic and ultrasonic range. The excessive levels of underwater noise adversely affects the so-called underwater acoustic climate and is the reason why this phenomenon is intensively investigated from the number of years. The results of experimental work...
-
New approach to railway noise modeling employing Genetic Algorithms
PublicationMain goal of this paper was to describe an innovative method of noise prediction based on Genetic Algorithms. First part of the paper addresses the problem of growing noise, mainly in the context of a unified method for measuring noise. Further, Genetic Algorithms are described with regards to their fundamental features. Further a description is provided as to how Genetic Algorithms were used in the area of noise modeling. Next...
-
Investigation of the underwater noise produced by ships by means of intensity method
Publication -
Quality assessment of ZnO-based varistors by 1/f noise
PublicationNoise has been used as a diagnostic tool of surge arrester varistor structures comprising of ZnO grains of various type and size. The physical and electrical properties of the measured samples have been described. In the experimental study, the applied measurement system and the results of noise measurements for the selected structures of varistors designed for the continuous working voltage 280 V, 440 V and 660 V have been presented....
-
Traffic Noise Analysis Applied to Automatic Vehicle Counting and Classification
PublicationProblems related to determining traffic noise characteristics are discussed in the context of automatic dynamic noise analysis based on noise level measurements and traffic prediction models. The obtained analytical results provide the second goal of the study, namely automatic vehicle counting and classification. Several traffic prediction models are presented and compared to the results of in-situ noise level measurements. Synchronized...
-
Pitting corrosion characterization by electrochemical noise measurements on asymmetric electrodes
PublicationKorozja wżerowa stali nierdzewnych może być wykryta za pomocą obserwacji charakterystycznych sygnałów prądowych, jakie płyną między dwiema elektrodami metalowymi. W artykule proponuje się wyznaczanie funkcji bispektrum dla układu dwóch elektrod o istotnie różnej powierzchni narażonej na występowanie korozji. Proponowana metoda została zastosowana do analizy korozji wżerowej stali 0H18N9 powstającej pod wpływem 1M roztworu FeCl3...
-
DEVELOPMENT OF A COUPLED NUMERICAL AND EXPERIMENTAL APPROACH TO HYDRODYNAMIC NOISE ESTIMATION
PublicationThe hydroacoustic signature of ships' propellers can be estimated experimentally through measurements of cavitation-induced pressure fluctuations and the corresponding noise distributions at model scale. These measurements need to be performed in a cavitation tunnel under the propellers operating conditions and are quite sensitive and challenging to perform with sufficient accuracy. In comparison, the numerical approach can be...
-
Distributed System For Noise Threat Evaluation Based On Psychoacoustic Measurements
PublicationAn innovative system designed for the continuous monitoring of acoustic climate of urban areas was presentedin the paper. The assessment of environmental threats is performed using online data, acquired through a grid ofengineered monitoring stations collecting comprehensive information about the acoustic climate of urban areas.The grid of proposed devices provides valuable data for the purpose of long and short time acoustic climateanalysis....
-
Performance of Noise Map Service Working in Cloud Computing Environment
PublicationIn the paper a noise map service designated for the user interested in environmental noise subject is presented. It is based on cloud computing. Noise prediction algorithm and source model, developed for creating acoustic maps, are working in cloud computing environment. In the study issues related to noise modeling of sound propagation in urban spaces are discussed with a special focus on road noise. Examples of results obtained...
-
Low Noise Poroelastic Road Pavements Based On Bituminous Binder
PublicationTire/road noise is the dominant source of traffic noise. It depends both on the tire design and on the characteristics of road pavements as well as on the vehicles’ operating conditions. Due to the fact that conventional (pneumatic) car tires have almost reached the limits of their ability to further reduce their noisiness, it is widely believed that the additional reduction of tire noise will be possible mainly through modifications...
-
Evaluation of Lombard Speech Models in the Context of Speech in Noise Enhancement
PublicationThe Lombard effect is one of the most well-known effects of noise on speech production. Speech with the Lombard effect is more easily recognizable in noisy environments than normal natural speech. Our previous investigations showed that speech synthesis models might retain Lombard-effect characteristics. In this study, we investigate several speech models, such as harmonic, source-filter, and sinusoidal, applied to Lombard speech...
-
Impact of Spatial Noise Correlation on Bearing Accuracy in DIFAR Systems
PublicationDIFAR type underwater passive systems are one of the more commonly used tools for detecting submarines. At the design stage, which usually uses computer simulations, it is necessary to generate acoustic noise of the sea. It has been shown that correlating noise significantly reduces these errors compared to the assumption that noise is uncorrelated. In addition, bearing errors have been shown to be the same in systems with a commonly...
-
Noise profiling for speech enhancement employing machine learning models
PublicationThis paper aims to propose a noise profiling method that can be performed in near real-time based on machine learning (ML). To address challenges related to noise profiling effectively, we start with a critical review of the literature background. Then, we outline the experiment performed consisting of two parts. The first part concerns the noise recognition model built upon several baseline classifiers and noise signal features...
-
Generation-recombination and 1/f noise in carbon nanotube networks
PublicationThe low-frequency noise is of special interest for carbon nanotubes devices, which are building blocks for a variety of sensors, including radio frequency and terahertz detectors. We studied noise in as-fabricated and aged carbon nanotube networks (CNNs) field-effect transistors. Contrary to the majority of previous publications, as-fabricated devices demonstrated the superposition of generation-recombination (GR) and 1/f noise...
-
Selective monitoring of noise emitted by vehicles involved in road traffic
PublicationAn acoustic intensity probe was developed measures the sound intensity in three orthogonal directions, making possible to calculate the azimuth and elevation angles, describing the sound source position. The acoustic sensor is made in the form of a cube with a side of 10 mm, on the inner surfaces of which the digital MEMS microphones are mounted. The algorithm works in two stages. The first stage is based on the analysis of sound...
-
Large shopping centres in Poznań as a source of rainwater recovery and irrigation of urban green areas
Publication -
Tripping of F-type RCDs for High-Frequency Residual Currents
PublicationResidual current devices (RCDs) are apparatus commonly used for protection against electric shock in low-voltage electrical installations. They protect people in the case of an earth fault or even in the case of direct contact with the live parts. However, to be effective protective devices, RCDs have to detect residual currents of various waveform shapes which appear in modern electrical installations. For this purpose, RCDs...
-
The effect of current delay angle on tripping of residual current devices
PublicationPower electronics converters applied in domestic or similar installations may utilize current delay (phase) angle control to change the level of transferred power. Due to application of such types of converters, earth fault current in the installation may be strongly distorted. The current distortion level depends on a value of current delay angle. This delay angle also influences the tripping threshold of residual current devices....
-
Time-current tripping curves of arc fault detection devices
PublicationTripping curves of arc fault detection devices, in accordance with PN-EN 62606 “General requirements for arc fault detection devices” have been presented in the paper. Consequently the most fundamental differences in arc fault detection devices tripping compared to circuit-breakers and residual current devices have been indicated.
-
Time-current tripping characteristics of RCDs for sinusoidal testing current
PublicationLow-voltage electrical installations are verified initially – before being put into operation, as well as periodically – during their utilization. According to the IEC standards, the scope of the verification includes measurements of both the tripping current and the disconnection time of residual current devices (RCDs). Experiences in RCDs testing show that disconnection times of two or more similar RCDs can be quite different....
-
Tripping of F-type RCDs for high-frequency residual currents
PublicationResidual current devices (RCDs) are apparatus commonly used for protection against electric shock in low-voltage electrical installations. They protect people in the case of an earth fault or even in the case of direct contact with the live parts. However, to be effective protective devices, RCDs have to detect residual currents of various waveform shapes which appear in modern electrical installations. For this purpose, RCDs are...
-
Methods and means of processing discrete information in networks with a high level of noise
Publication -
Certification requirements for tram noise measurements in terms of today’s expectations in cities
Publication -
Reduction of Influence of the High-Frequency Noise on the Results of Surface Topography Measurements
Publication -
Tire/road noise measuring principles according to the Close Proximity Method
PublicationW pracy podano metody badania hałasu opon samochodowych. Omówiono przyczepy pomiarowe zbudowane w Politechnice Gdańskiej oraz systemy pomiarowe stosowane do pomiaru hałasu opon zgodnie z metodą CPX.
-
Quality assessments of electrochromic devices: the possibleuse of 1/f current noise
PublicationElementy wykorzystujące zjawisko elektrochromizmu, potrafiące zmieniać przezroczystość za pomocą ładowania/rozładowania ładunkiem elektrycznym, wykonano na bazie laminatów pokrytych porowatą strukturą tlenków Ni oraz tlenków Wi-V. Oba laminaty, na które naniesiono przewodzącą warstwę In2O3, przedzielono warstwą elektrolitu. Obserwowano szumy typu 1/f w prądzie I płynącym w trakcie rozładowywania urządzenia. Gęstość widmowa mocy...
-
High quality speech codec employing sines+noise+transients model
PublicationA method of high quality wideband speech signal representation employing sines+transients+noise model is presented. The need for a wideband speech coding approach as well as various methods for analysis and synthesis of sines, residual and transient states of speech signal is discussed. The perceptual criterion is applied in the proposed approach during encoding of sines amplitudes in order to reduce bandwidth requirements and...
-
Measurement of noise parameter set in the low frequency range: requirements and instrumentation.
PublicationOpisano dwa podstawowe szumowe modele metrologiczne czwórnika: ze źródłami szumów odniesionymi do wejścia i ze zwarciowymi prądami szumów. Parametry szumowe opisujące modele zawierające korelację pomiędzy prądami i/lub napięciami są mierzone przy zastosowaniu metod bezpośrednich i pośrednich. Przedstawiono kilka technik redukcji szumów własnych systemu pomiarowego. Szerzej zaprezentowano dwukanałowy system do pomiaru szumów z komputerowym...
-
Noise reduction in audio employing spectral unpredictability measure and neural net.
Publicationmodelu psychoakustycznym zostały przedyskutowane. Uczący się algorytm decyzjny, działający w opraciu o sztuczną sieć neuronową wykorzystany został w klasyfikacji składowych na pasożytnicze i użyteczne. Przedstawiona została również nowa iteracyjna procedura obliczania progu maskowania. W pracy zawarte zostały wyniki eksperymentów, oraz konkluzje odnoszące się do przedstawionych algorytmów.
-
Low frequency noise and DLTS as silicon solar cell characterization tools
PublicationPraca zawiera wyniki pomiarów DLTS próbek o powierzchni 1 mm2 krzemowych baterii słonecznych wykazujących znaczne niejednorodności wykryte za pomocą metody LBIV (Light Beam Induced Voltage). Wyniki pomiarów charakterystyk stałoprądowych oraz szumowych tych próbek zostały także przedstawione.
-
Modeling incipient creep damage effects on Barkhausen noise and magnetoacoustic emission.
PublicationZaproponowano model fizyczny opisujący zmiany natężenia efektu Barkhausena i emisji magnetoakustycznej podczas procesu degradacji stali ekploatowanych w przemyśle energetycznym.
-
ROSANNE Project: New Procedure for Noise Characterisation of Road Surfaces in Europe
PublicationROSANNE is a collaborative project in the 7th EU Framework Programme which aims at harmonising measurement methods for skid resistance, noise emission and rolling resistance of road pavements as a preparation for standardization. The project started in November 2013 and is developing and improving standards in the field of working group CEN/TC 227/WG 5. Regarding the influence of the pavement on the road traffic noise emission,...
-
Realistic noise-tolerant randomness amplification using finite number of devices
PublicationRandomness is a fundamental concept, with implications from security of modern data systems, to fundamental laws of nature and even the philosophy of science. Randomness is called certified if it describes events that cannot be pre-determined by an external adversary. It is known that weak certified randomness can be amplified to nearly ideal randomness using quantum-mechanical systems. However, so far, it was unclear whether randomness amplification...
-
Signal conditioning for examination of shallow-water acoustic noise correlation properties
PublicationThe article describes the process of signal conditioning for examination of acoustic noise correlation properties in shallow water. Knowledge of these properties is very important for the design processes of passive and active hydroacoustic systems. This paper focuses on the above issue from the point of view of passive sonar. In sonar systems, signal processing algorithms operate on both useful acoustic signals, and accompanying...
-
Certification of vehicles used for tire/road noise evaluation by CPX method
PublicationJednym ze sposobów oceny hałasu opon i nawierzchni drogowych jest metda CPX polegająca na pomiarze hałasu w polu bliskim miejsca współpracy opony z nawierzchnią. Aby uzyskać wysoką dokładność pomiarów niezbędne jest ustanowienie procedur ustanowienie procedur certyfikacyjnych sprzętu pomiarowego a więc głównie pojazdu badawczego. Praca dotyczy procedur certyfikacyjnych wypracowanych przez Grupę Roboczą WG33 ISO/TC43/SC1 oraz w...
-
Low-frequency noise in ZrS3 van der Waals semiconductor nanoribbons
PublicationWe report the results of the investigation of low-frequency electronic noise in ZrS3 van der Waals semiconductor nanoribbons. The test structures were of the back-gated field-effect-transistor type with a normally off n-channel and an on-to-off ratio of up to four orders of magnitude. The current–voltage transfer characteristics revealed significant hysteresis owing to the presence of deep levels. The noise in ZrS3 nanoribbons...
-
Tyre/road noise reduction of poroelastic road surface tested in a laboratory
PublicationA so-called poroelastic road surface (PERS) is being developed in Europe. This contains a large percentage of rubber particles mixed with hard aggregate (stone and sand) and bound with polyurethane. This gives high air void content (around 30 %), high elasticity and smooth texture, all of which should give low noise properties. Inthis experiment anominally 30 mm thick sample of PERS was mounted on a steel drum. Various car tyres...
-
Noise Generated by Tyres Designet for Electric Vehicles - Results of Laboratory Experiments
PublicationA few years ago, electric and hybrid vehicles were rarely seen on public roads and were considered more as exotic curiosities or even as a sign of extravagance than a practical means of transport. Nowadays the situation has changes significantly. This was caused both by the technical development and legislative actions, as well as the organizational nature promoting the purchace and use of low emission vehicles. Electric vehicles...
-
INFLUENCE OF TEST CONDITIONS ON TYRE/ROAD NOISE MEASURED BY THE DRUM METHOD
PublicationTyre/road noise is one of the most important environmental problems related to road traffic. Nowadays a few standard procedures of tyre/road noise measurements are in use. Unfortunately, measurement conditions specified within relevant standards are very different. For example, procedure described in ISO 11819-2 used for pavement investigations requires tyre load of 3200 N and capped inflation pressure of 200 kPa. At the same time...
-
The importance of the bottom layer in double-layer porous asphalt for noise reduction
PublicationDouble-layer porous asphalt concrete (DPAC) surfaces are generally considered to be the acoustically most effective low noise road surfaces ready for implementation. While DPAC used on highways in warm climates may have an average life of around 8 years, in Scandinavia with severe winter climate DPAC usually survive only about 3 years; partly due to wear of studded tyres. An ongoing project in Sweden, applying DPAC and single-layer...