Publications
Filters
total: 313
Catalog Publications
Year 2017
-
Diagnozowanie turbin parowych
PublicationDiagnozowanie turbin parowych jest to istotny proces mający na celu utrzymanie diagnozowanego obiektu w stanie zdatności zadaniowej z jak największą sprawnością. W procesie diagnozowania turbin wykorzystuje się diagnostykę cieplno-przepływową, należy do diagnostyki technicznej zajmującej się badaniem oraz oceną przemian energetycznych.
-
Elektrociepłownie- przegląd rozwiązań
PublicationW artykule przedstawione i opisane zostały rożnego typu układy elektrociepłowni. Systemy zostały sklasyfikowane ze względu na konstrukcję. Przedstawione zostały główne wady i zalety każdego rozwiązań. Artykuł ukazuje również zalety kogeneracji jako sposobu wytwarzania w bardziej efektywny sposób energii elektrycznej oraz cieplnej.
-
Elimination and migration of hydrogen in the vacuum-ultraviolet photodissociation of pyridine molecules
PublicationElimination of the excited hydrogen atoms H(n), n = 4–7, and hydrogen migration in formation of the excited NH(A 3Π) free radicals in the photodissociation of pyridine, C5H5N, molecules have been studied over the 17.5–70 eV photon energy range. In the measurements the photon-induced fluorescence spectroscopy technique has been applied. Both fragments are produced through excitation of pyridine molecules into higher-lying superexcited...
-
Fault diagnosis of marine 4-stroke diesel engines using a one-vs-one extreme learning ensemble
PublicationThis paper proposes a novel approach for intelligent fault diagnosis for stroke Diesel marine engines, which are commonly used in on-road and marine transportation. The safety and reliability of a ship's work rely strongly on the performance of such an engine; therefore, early detection of any type of failure that affects the engine is of crucial importance. Automatic diagnostic systems are of special importance because they can...
-
Gold nanoparticles and their coatings, their effect on cells and their interaction with radiation
PublicationTwo nanometre gold nanoparticles (AuNPs), bearing sugar moieties and/or polyethylene glycolamine (PEG-amine), were synthesised and evaluated for their in vitro toxicity and ability to radiosensitise cells with 220 kV and 6 MV X-rays, using four cell lines representing normal and cancerous skin and breast tissues. In addition to the observed intrinsic cancer-selective chemotoxicity, these AuNPs acted as radiosensitisers in combination with...
-
Isobutyl acetate: electronic state spectroscopy by high-resolution vacuum ultraviolet photoabsorption, He(I) photoelectron spectroscopy and ab initio calculations
PublicationThe high-resolution vacuum ultraviolet photoabsorption spectrum of isobutyl acetate, C6H12O2, is presented here and was measured over the energy range 4.3–10.8 eV (290–115 nm). Valence and Rydberg transitions with their associated vibronic series have been observed in the photoabsorption spectrum and are assigned in accordance with new ab initio calculations of the vertical excitation energies and oscillator strengths. The measured...
-
Kurs na energię
PublicationJednym z nadrzędnych celów, jakie stawia przed sobą Unia Europejska, jest realizacja tzw. polityki zrównoważonego rozwoju. Ma ona polegać na implikacji sprzyjających warunków dla powstania konkurencyjnej gospodarki niskoemisyjnej.
-
Low-energy interactions related to atmospheric and extreme conditions
PublicationThis Topical Issue, entitled “Low-Energy Interactions Related to Atmospheric and Extreme Conditions”, showcases a collection of eighteen articles that reported recent theoretical and experimental findings pertaining to the following topics: – low-energy interactions of charged particles (electrons [1–7], protons [8], positrons [9]), and photons [10] with atoms and molecules of biological [1–4,7,8], astrochemical [10], industrial,...
-
MAGAZYNOWANIE ENERGII CIEPLNEJ DLA POTRZEB BUDYNKU - PRZEGLĄD ROZWIĄZAŃ I SPOSOBÓW ZINTEGROWANIA ICH Z BRYŁĄ OBIEKTU
PublicationMagazynowanie energii cieplnej pozyskanej ze źródeł odnawialnych to obiecująca technologia mająca poprawić wydajność energetyczną budynków. Jest to obecnie popularny temat wielu badań dążących do doboru optymalnych parametrów magazynu, takich jak jego rozmiar, rodzaj wypełnienia, lokalizacja i sposób instalacji w budynku. Każdy z tych czynników ma istotny wpływ na zmniejszenie zapotrzebowania energetycznego zarówno w sektorze budownictwa...
-
Photoelectron spectroscopy of a series of acetate and propionate esters
PublicationThe electronic state and photoionization spectroscopy of a series of acetate esters: methyl acetate, isopropyl acetate, butyl acetate and pentyl acetate as well as two propionates: methyl propionate and ethyl propionate, have been determined using vacuum-ultraviolet photoelectron spectroscopy. These experimental investigations are complemented by ab initio calculations. The measured first adiabatic and vertical ionization energies...
-
Preliminary design of the last stage of supercritical steam turbine and proposition of anti-erosion coating for blades surface
PublicationIn this article a preliminary design of the last stage of supercritical steam turbine has been presented. A computational model of supercritical thermal cycle has been created in order to determine steam parameters at the stage inlet and outlet. The model was based on the structure of German coal-fired power plant Datteln 4. Further steam-flow parame-ters and dimensions of stator and rotor blades have been calculated analytically....
-
Sposoby zagospodarowania ciepła odpadowego z silników jednostek pływających Cześć 2. Wykorzystanie ciepła do ogrzewania
PublicationW pierwszej części artykułu (COW 2/2017) omówiono możliwości wykorzystania nieużytkowej energii chemicznej paliwa do chłodzenia jednostek pływających. W drugiej części autorzy opisali systemy pozwalające wykorzystać tę energię do ogrzewania. Oprócz opisania budowy układów pozwalających na wykorzystanie ciepła odpadowego do ogrzewania, porównano je pod względem wydajności. Podjęto także próbę wskazania rozwiązania o najwyższej efektywności...
-
Sposoby zagospodarowania ciepła odpadowego z silników napędowych jednostek pływających Cześć 1. Wykorzystanie ciepła do napędu urządzeń chłodniczych
PublicationEnergia chemiczna paliwa jest w wielu przypadkach zaledwie w połowie wykorzystana jako energia napędowa silnika. Pozostała część jako ciepło odpadowe przekazywana jest do otoczenia. Dzięki odpowiednim układom przetwarzania ciepło ze spalin można wykorzystać do wytwarzania chłodu lub jako ciepło użytkowe, w systemach HVAC (ang. heating, ventilation, air conditioning – ogrzewanie, wentylacja, klimatyzacja). Tym samym koszty pracy...
-
Systems for storing and reducing energy consumption in residential buildings
PublicationW pracy przeprowadzany został przegląd różnych koncepcji magazynów energii cieplnej zintegrowanych z budynkiem mieszkalnym. Przedstawione zostały warianty różniące się między sobą pod względem kształtu, rozmiaru, wypełnienia, sposobu instalacji itp. Opisany został sposób zintegrowania systemów magazynujących z odnawialnymi źródłami energii. Następnie wskazane zostały inne rozwiązania projektowe umożliwiające redukcję zapotrzebowania...
-
The experimental identification of the dynamic coefficients of two hydrodynamic journal bearings operating at constant rotational speed and under nonlinear conditions.
PublicationHydrodynamic bearings are commonly used in ship propulsion systems. Typically, they are calculated using numerical or experimental methods. This paper presents an experimental study through which it has been possible to estimate 24 dynamic coefficients of two hydrodynamic slide bearings operating under nonlinear conditions. During the investigation, bearing mass coefficients are identified by means of a newly developed algorithm....
-
TOTAL SHIP OPERABILITY – REVIEW, CONCEPT AND CRITERIA
PublicationThe ship operability can be understood and analysed in different manners, and its quality is described using different indexes by different authors. Practically, there is no general and widely accepted description of total ship operability in the literature, nor in the rules of classification societies, which would include both seakeeping and manoeuvrability characteristics of a ship, and simultaneously take into account all ship...
-
Tradycyjna lodownia – ekoenergetyczny magazyn żywności
PublicationW artykule omówiono konstrukcję oraz zasadę działania naturalnych przechowalni żywności, tzw. lodowni. Przedstawiono kilka przykładów takich konstrukcji wraz z opisem ich budowy. Na przykładzie jednego rozwiązania szczegółowo opisano zasadę działania procesów zachodzących wewnątrz przechowalni. Podkreślono neutralność tego typu budowli wobec środowiska. Przedstawiono zalety i wady analizowanego rozwiązania na tle sprężarkowych...
-
Turbiny parowe i gazowe
PublicationArtykuł opisuje turbiny parowe i gazowe. Autorka przedstawia chronologię wynalezienia turbin ich zasadę działania i najważniejsze zastosowania. W pracy przedstawione zostały różnice między turbinami parowymi i gazowymi i wynikające z tego wady i zalety obu rozwiązań.
-
Wyznaczenie charakterystyk eksploatacyjnych siłowni turbinowej o mocy 400 MW z reaktorem wysokotemperaturowym w zmiennych warunkach pracy
PublicationW artykule przedstawiono charakterystyki sprawnościowe dla siłowni turbinowej o mocy 400 MW zasilanej przez reaktor wysokotemperaturowy. Przedstawione charakterystyki stworzone zostały dla zmiennych warunków pracy opisanego obiegu. Obliczenia numeryczne symulujące działanie siłowni wykonano w programie DIAGAR. Jako zmienne warunki ruchu obiegu jądrowego przyjęto zmianę ciśnienia w skraplaczu. Na tej podsatwie określono zmianę sprawności...
-
Wyznaczenie charakterystyk eksploatacyjnych siłowni turbinowej o mocy 400 MW z reaktorem wysokotemperaturowym w zmiennych warunkach pracy.
PublicationW referacie przedstawiono charakterystyki sprawnościowe dla siłowni turbinowej o mocy 400 MW zasilanej przez reaktor wysokotemperaturowy. Przedstawione charakterystyki stworzone zostały dla zmiennych warunków pracy opisanego obiegu. Obliczenia numeryczne symulujące działanie siłowni wykonane zostały w programie DIAGAR. Jako zmienne warunki ruchu obiegu jądrowego przyjęto zmianę ciśnienia w skraplaczu. Na tej podstawie określono...
-
Zirconia ceramics with additions of Alumina for advanced tribological and biomedical applications
PublicationThe results of an investigation on slip cast and sintered Y2O3 (3 wt%)- stabilized ZrO2 with additions of 5, 10, 15 wt% Al2O3 are reported. The surface roughness, porosity and density of the samples were measured. The hardness HRc and Hv, fracture toughness K1C, and friction coefficients were also measured using standard methods. The structural properties of the samples were observed by Scanning Electron Microscopy (SEM). The surface...
Year 2018
-
Analiza możliwości ograniczenia emisji gazów cieplarnianych ze statków dalekomorskich
PublicationW artykule przedstawiono możliwości ograniczania emisji gazów cieplarnianych ze statków dalekomorskich. Przedstawiono również analizę tych rozwiązań. W ogólnym zarysie metody ograniczania emisji gazów cieplarnianych sprowadzają się do zwiększenia efektywności energetycznej statków poprzez zwiększenie efektywności działania źródeł energii w tym silników okrętowych, zwiększenie efektywności napędu statku, minimalizowanie zużycia...
-
Comparative analysis of thermodynamic cycles of selected nuclear ship power plants with high-temperature helium-cooled nuclear reactor
PublicationThis paper presents a comparative analysis of thermodynamic cycles of two ship power plant systems with a high-temperature helium- cooled nuclear reactor. The first of them is a gas system with recuperator , in which classical gas chamber is substituted for a HTGR reactor (High Temperature Gas-cooled Reactor) . The second of the considered cycles is a combined gas-steam system where working medium flux from gas turbine outlet...
-
Comparison analysis of selected nuclear power plants supplied with helium from high-temperature gas-cooled reactor
PublicationThe article presents results of efficiency calculations for two 560 MW nuclear cycles with high-temperature gas-cooled reactor (HTGR). An assumption was made that systems of this type can be used in so-called marine nuclear power plants. The first analysed system is the nuclear steam power plant. For the steam cycle, the efficiency calculations were performed with the code DIAGAR, which is dedicated for analysing this type of systems....
-
Electron impact ionization and cationic fragmentation of the pyridazine molecules
PublicationElectron impact mass spectroscopy was used to investigate ionization and cationic fragmentation of the pyridazine (1,2 diazine), C4H4N2, molecules in the gas phase. The mass spectra were measured and the observed mass peaks assigned to the corresponding cations. The appearance energies of most of the cationic fragments were determined and the possible fragmentation processes are discussed. The total cross section for electron...
-
Experimental investigations on heat transfer enhancement in shell coil heat exchanger with VARIABLE Baffles GEOMETRY
PublicationThe paper presents the possibility of using passive intensification of heat transfer in the form of baffles to increase the energy efficiency of the shell and coil heat exchanger. The experiment was carried out by using a modular coil heat exchanger in the form of an electric heater. Water was used as a working fluid with constant thermal-flow parameters at the inlet of the module. It should be noted that experiments were made...
-
EXPERIMENTAL RESEARCH ON INFLUENCE OF THE FUEL NOZZLE GEOMETRY ON THE FUEL CONSUMPTION OF THE MARINE 4-STROKE DIESEL ENGINE
PublicationThe article presents experimental research that has been carried out on a marine, 4-stroke, 3-cylinder, turbocharged engine. During testing, the engine operated at a constant rotational speed of 750 rpm and a load from 0 kW to 280 kW. The engine was fuelled by diesel oil of known specification and loaded by electric generator with water resistance. The fuel consumption was measured during the engine operation with fuel nozzles...
-
Hydroperoxyl radical and formic acid formation from common DNA stabilizers upon low energy electron attachment
Publication2-Amino-2-(hydroxymethyl)-1,3-propanediol (TRIS) and ethylenediaminetetraacetic acid (EDTA) are key components of biological buffers and are frequently used as DNA stabilizers in irradiation studies. Such surface or liquid phase studies are done with the aim to understand the fundamental mechanisms of DNA radiation damage and to improve cancer radiotherapy. When ionizing radiation is used, abundant secondary electrons are formed...
-
INCREASING POWER SUPPLY SAFETY IN THE ASPECT OF SUPPORTING THE RENEWABLE ENERGY SOURCES BY CONVENTIONAL AND VIRTUAL POWER STORES
PublicationThis paper presents characteristics and purposefulness of supporting the renewable energy sources (OZE) by means of energy stores. The main emphasis was placed on analysis of virtual energy stores available for implementation in Polish economy conditions. A role which management of Demand Side Response (DSR) may play in balancing Polish electric power system, is discussed. Implementation of such solutions together with conventional...
-
Istotność procesu selekcji przy wykorzystaniu algorytmów genetycznych do diagnostyki cieplno-przepływowej
PublicationArtykuł ten ma za zadanie przedstawić istotność zastosowania procesu selekcji przy diagnozowaniu turbin parowych. Możliwość zastosowania algorytmów genetycznych w diagnostyce cieplno-przepływowej wiąże się z zastosowaniem selekcji występujących parametrów, proces selekcji jest najtrudniejszy ze względu na liczbę parametrów. Liczba degradujących się parametrów może być różna tzn. możemy mówić o degradacji jednokrotnej lub wielokrotnej....
-
Klasyfikator rozmyty użyteczny we wstępnym doborze profili łopatkowych turbin parowych
PublicationW artykule przedstawiona została próba stworzenia wstępnego modelu klasyfikatora rozmytego użytecnego we wstępnym doborze profili łopatkowych turbin parowych. Dobór odpowiedniego rozwiązania dokonywany jest na podstawie parametrów przepływu czynnika przez wieńce turbiny. Tego typu narzędzie decyzyjne może okazać się przydatne zarówno w przypadku modernizacji istniejących już obiektów, w których zdiagnozowane uszkodzenia wymuszają...
-
New Concept of Numerical Ship Motion Modelling for Total Ship Operability Analysis by Integrating Ship and Environment Under One Overall System
PublicationThe paper presents a new concept of overall ship motion modelling for application to total ship operability. The delivered model is a multi-phase and includes both submerged part of ship’s hull and the surrounding water as a unique body. The Discrete Finite Element Method is applied. The model is successfully examined and illustrated for a selected AHTS.
-
Profesorowie Politechniki Gdańskiej w procesie projektowania, budowy i eksploatacji „Sołdka”
PublicationPrzedstawiono sylwetki profesorów Politechniki Gdańskiej uczestniczących w czasie projektowanie, budowy i eksploatacji pierwszego statku handlowego "Sołdek" wybudowanego w 1948 r. w Stoczni Gdańskiej
-
Propulsion and Maneuvering Systems’ Characteristics of the U.S. Flagged Great Lakes Self-Unloading Bulk Carriers
PublicationPaper contains an overview of the propulsion and maneuvering systems’ characteristics of United States flagged Great Lakes self - unloading bulk carriers. A contrast between the importance of the transport task carried by those vessels to their low number and considerable age suggests the need to review and understand their complexity as well as complexity of their operations in order to provide suitable energy- and operational...
-
Rozkład naprężeń mechanicznych w łyżce o szerokości 500 mm, przeznaczonej do koparki podsiębiernej
PublicationW artykule zaprezentowano optymalizację kształtu łyżki koparki przedsiębiernej z wykorzystaniem analizy wytrzymałościowej. Analizę oparto na trójwymiarowym modelu konstrukcji łyżki z zastosowaniem metody elementów skończonych (MES). Opracowanie wspomnianej metody pozwoliło na modyfikację konstrukcji łyżki, która dała w efekcie obniżenie naprężeń złożonych w newralgicznych obszarach konstrukcji łyżki. Przedstawiona analiza okazała...
-
SELECTED COMBINED POWER SYSTEMS CONSISTED OF SELFIGNITION ENGINE AND STEAM TURBINE
PublicationThis paper presents optimization of selected combined diesel engine-steam turbine systems. Two systems: the system combined with waste heat one-pressure boiler only and its version containing additionally low-pressure boiler proper feeding degasifier and the system of two-pressure cycle, were taken into considerations. Their surplus values of power output and efficiency associated with utilization of waste heat contained in piston...
-
The Emission and Combustion Characteristics of Marine Diesel Engine with Extreme Throttled of Air or Exhaust Ducts
PublicationPresented paper shows the results of the laboratory tests on the relationship between the extreme throttling of both air intake duct and exhaust gas duct and gaseous emission from the marine engine. The object of research is a laboratory, 4-stroke, DI diesel engine, operated at loads from 50 kW to 250 kW at a constant speed equal to 750 rpm. During the laboratory tests the thermodynamic and exhaust gas emission characteristics...
-
The Experimental Determination of Bearings Dynamic Coefficients in a Wide Range of Rotational Speeds, Taking into Account the Resonance and Hydrodynamic Instability
PublicationMethods for the experimental determination of dynamic coefficients are commonly used for the analysis of various types of bearings, including hydrodynamic, aerodynamic and foil bearings. There are currently several algorithms that allow estimating bearing dynamic coefficients. Such algorithms usually use various excitation techniques applied to rotor–bearings systems. So far only a small number of scientific publications show how...
-
The influence of the fuel spray nozzle geometry on the exhaust gas composition from the marine 4-stroke diesel engine
PublicationThe paper presents experimental research on a 4-stroke, 3-cylinder, turbocharged AL25/30 Diesel engine. Research consisted in investigating the effect of the geometry of the fuel injectors on the exhaust gas composition from the engine. During measurements, the engine was operated with a regulator characteristic of a load range from 40 kW to 280 kW, made by electric water resistance. The engine was mechanically coupled to the electric...
-
Wybrane zagadnienia przepływowe turbiny gazowej pracującej w tłoczni gazu ziemnego.
PublicationW niniejszym artykule przedstawiono cieplno-przepływowe obliczenia turbiny gazowej, stanowiącej napęd sprężarki w tłoczni gazu ziemnego. Wartości parametrów wejściowych niezbędnych do przeprowadzenia obliczeń przyjęto na podstawie danych technicznych tłoczni zasilających polski odcinek gazociągu tranzytowego Jamał-Europa, w których pracują turbiny gazowe SGT-600 firmy Siemens, o mocy 25,3 MW.
-
Wykorzystanie magazynu chłodu w kompaktowej komorze przechowalniczej
PublicationNiniejszy artykuł został poświęcony możliwości wykorzystania pasywnych systemów chłodzenia w mobilnych komorach przechowalniczych. Dokonano przeglądu rozwiązań dostępnych na rynku komór termicznych wraz z wykorzystywanymi w nich technologiami chłodzenia. Przeprowadzono analizę możliwych do zastosowania nośników chłodu w systemach pasywnego chłodzenia. Wykazano, iż oprócz popularnych na rynku materiałów zmiennofazowych (PCM – ang....
Year 2019
-
ANALIZA KRYTYCZNA METOD OBLICZANIA USZCZELNIEŃ LABIRYNTOWYCH W MASZYNACH CIEPLNYCH WIRNIKOWYCH
PublicationUszczelnienia labiryntowe są ważnym elementem budowy maszyn cieplnych wirnikowych. Istnieje wiele metod obliczeniowych, pozwalających określić parametry termodynamicznych gazu na długości dławnicy labiryntowej W niniejszej pracy przedstawiona zostanie krytyczna analiza metod obliczania uszczelnień labiryntowych dostępnych w literaturze oraz przykładowe wyniki obliczeń wykonanych metodą wyznaczania linii Fanno i zasady De Saint...
-
Analysis of the macrostructure of the fuel spray atomized with marine engine injector
PublicationOne of the main problem influencing the combustion process in the cylinder of the marine engine is an fuel spray phenomena. The parameters describing the shape of the fuel spray are named macro parameters. This article presents the research results of the macrostructure parameters of the fuel spray atomized with the marine engine injector. The research were carried out by optical visualization measurement method of Mie scattering....
-
APPLICABILITY OF INLET AIR FOGGING TO MARINE GAS TURBINE
PublicationThe dependency of marine gas turbine on the ambient temperature leads to a decrease of the gas turbine power output in arid areas. Very often gas turbine power output demand is high and the power margins originally designed into the driver , has been exhausted. In such circumstances the inlet air fogging is an effective compensation of gas turbine power. In this paper an analysis of inlet air fogging applicability to marine gas...
-
Application of Thermo-chemical Technologies for Conversion of Associated Gas in Diesel-Gas Turbine Installations for Oil and Gas Floating Units
PublicationThe paper considers the issue of thermo-chemical recovery of engine’s waste heat and its further use for steam conversion of the associated gas for oil and gas floating units. The characteristics of the associated gas are presented, and problems of its application in dual-fuel medium-speed internal combustion engines are discussed. Various variants of combined diesel-gas turbine power plant with thermo-chemical heat recovery are...
-
BADANIA PILOTAŻOWE DRGAŃ NA WLOCIE DO SPRĘŻARKI TURBINY GAZOWEJ GTD 350
PublicationPodstawą diagnostyki maszyn wirnikowych są pomiary drgań ze względu na to że prawie wszystkie uszkodzenia maszyn powodują istotne zmiany wielkości je opisujących np. prędkości drgań. W eksploatacji maszyn wirnikowych najważniejsza jest ocena drgań obiektu na podstawie pomiarów wykonywanych na częściach niewirujących. Badania, których wyniki przedstawiono w referacie zostały przeprowadzone na stanowisku...
-
Framework of an Evolutionary Multi-Objective Optimisation Method for Planning a Safe Trajectory for a Marine Autonomous Surface Ship
PublicationThis paper represents the first stage of research into a multi-objective method of planning safe trajectories for marine autonomous surface ships (MASSs) involved in encounter situations. Our method applies an evolutionary multi-objective optimisation (EMO) approach to pursue three objectives: minimisation of the risk of collision, minimisation of fuel consumption due to collision avoidance manoeuvres, and minimisation of the extra...
-
High performance super-twisting sliding mode control for a maritime autonomous surface ship (MASS) using ADP-Based adaptive gains and time delay estimation
PublicationThis research addresses two kinds of problems related to optimal trajectory tracking of a Maritime Autonomous Surface Ship (MASS): those caused by the time-varying external disturbances including winds, waves and ocean currents as well as those resulting from inherent dynamical uncertainties. As the paper shows, an accurate and robust optimal controller can successfully deal with both issues. An improved Optimal Adaptive Super-Twisting...
-
Investigation of the Combustion Processes in the Gas Turbine Module of an FPSO Operating on Associated Gas Conversion Products
PublicationIn this paper, we consider the issue of thermo-chemical heat recovery of waste heat from gas turbine engines for the steam conversion of associated gas for offshore vessels. Current trends in the development of offshore infrastructure are identified, and the composition of power plants for mobile offshore drilling units and FPSO vessels is analyzed. We present the results of a comparison of power-to-volume ratio, power-to-weight...
-
Porównanie wybranych typów elektrowni jądrowych z reaktorem HTGR
PublicationWśród interesujących rozwiązań elektrowni jądrowych USA, Rosja i Chiny proponują zastosowanie tzw. pływających morskich elektrowni nuklearnych. Wchodzi w rachubę wyposażenie ich w reaktor wysokotemperaturowy typu HTGR, chłodzony gazem. Przeprowadzono rozważania i obliczenia sprawności dla bloków 560 MW parowej elektrowni jądrowej i elektrowni z turbiną gazową. Wyższa sprawność turbin parowych nie dyskredytuje możliwości zastosowania...