Wyszukiwarka
dr inż. Aleksandra Suchta
Zatrudnienie
- asystent w Katedra Energetyki i Aparatury Przemysłowej
- asystent naukowo-dydaktyczny w Instytut Technologii Maszyn i Materiałów
- Adiunkt w Instytut Technologii Maszyn i Materiałów
Obszary badawcze
Publikacje
Filtry
wszystkich: 23
Katalog Publikacji
Rok 2024
-
The Impact of Drying Conditions on the Surface Color Changes of Pine Wood
PublikacjaThe article presents the impact of drying process and selected parameters on the color changes on the surface of pine wood (Pinus sylvestris L.). Three predetermined process conditions (modes), mild, normal, and intensive, were investigated. The experiments were conducted using a semi-industrial scale dryer designed at the Gdańsk University of Technology with a loading capacity of 0.55 m3. The drying process was applied to pine...
Rok 2022
-
EFFECT OF PRESS DRYING ON DIMENSION STABILITY AND DENSITY OF BEECH WOOD,
PublikacjaTimber is traditionally dried in kilns by processes that often take several days or weeks to complete. At present, it is possible to apply several methods of rapid drying of timber, including, for example, press drying. This research is based on the use of this process. Drying was performed using the heating plates with a temperature of 160 °C. Three pressures were compared in the research 1.0 MPa, 1.4 MPa, and 1.8 MPa. The density...
-
Preliminary studies on the effect of feed speed on the colour change of wood
PublikacjaThis paper presents the results of preliminary analyses of the effect of cutting parameters on changes in the colour of wood. Beech wood cut with use circular saw was analysed. The cutting parameter tested was the feed speed, represented by the feed per tooth. Sawing processes with different feed per tooth ranging from 0.0008 mm to 0.09 mm were analysed. It was observed that over the entire range of feed rate per tooth analysed,...
-
The effect of beech wood (Fagus sylvatica L.) steaming process on the colour change versus depth of tested wood layer
PublikacjaThe results of experimental research on the colour changes of beech wood at different depths of the tested layer are presented. Beech wood (Fagus sylvatica L.) dried in a conventional kiln was tested. Half of the wood samples were steamed prior to the drying process. Colour changes were measured at various depths after the face milling process was used to remove the material to expose to the deeper surface. The colour changes were...
Rok 2021
-
Comparison of the fracture toughness of pine wood determined on the basis of orthogonal linear cutting and frame sawing
PublikacjaIn this paper, the values of the fracture toughness of Scots pine determined by cutting tests are presented. The cutting tests were carried out using the samples of Scotch pine (Pinus sylvestris L.) from Pomeranian Region, Poland. These experiments were carried out on two research stands: orthogonal linear cutting tests were conducted using the microtome instrument and the frame saw PRW-15M was used for sawing tests. The values...
-
Mathematical model of the energy consumption calculation during the pine sawn wood (Pinus sylvestris L.) drying process
PublikacjaThe article presents the modification of the existing mathematical model to calculate energy consumption during conventional drying process. Apart from energy consumption the model permits to estimate the time of high-temperature drying process. The drying medium is air and superheated steam mixture. The obtained calculation results were compared with conducted experimental tests of drying square-edged sawn sapwood timber (Pinus...
-
The Influence of Drying Temperature on Color Change of Hornbeam and Maple Wood Used as Surface and Inner Layers of Wood Composites
PublikacjaThe thermal treatment of wood changes its structure due to the degradation of wood polymers (cellulose, hemicellulose and lignin), so the physical properties of wood are either improved or degraded. Color changes apply not only to natural wood, but also to such wood composites for which some amount of glue is used in their construction (e.g., plywood, blockboard or laminboard). This article is focused on the analysis of hornbeam...
-
Wood Moisture-Content Measurement Accuracy of Impregnated and Nonimpregnated Wood
PublikacjaThe influence of the impregnation process of pine wood (Pinus sylvestris L.) samples on the electrical resistance changes and the moisture-content measurement accuracy is presented in this paper. In this study, the resistances of impregnated and nonimpregnated green pine timber harvested from northern Poland were compared. An impregnation method based on a vacuum-pressure chamber was used. Copper salts were applied as the impregnated...
Rok 2020
-
Deformation and Surface Color Changes of Beech and Oak Wood Lamellas Resulting from the Drying Process
PublikacjaThe drying process was examined relative to parameters’ influence on the deformation and surface layer color changes of beech wood (Fagus sylvatica L.) and oak wood (Quercus robur L.). The goal was to analyze the impact of drying process conditions, wood and growth rings types, and load on the deformation and surface color changes of drying thin wooden elements. A further aim was to reduce the time of the lamella drying and minimize...
-
THE EFFECT OF DRYING INTENSITY ON THE COLOR CHANGES OF PINE WOOD (PINUS SYLVESTRIS L.)
PublikacjaThe effect of the selection of drying process parameters on the color change of Scots pine wood (Pinus Sylvestris L.) is presented. In this work the experimental studies have been performed. The research focused on the influence of drying intensity on the changes of color after drying process. Intensity of drying process was determined on the basis of the average drying gradient. To determine the color of wood before and after...
Rok 2019
-
Impact of high temperature drying process on beech wood containing tension wood
PublikacjaThe technology of high temperature drying has a great inuence on dimensional and selected physical changes in tension wood. Article is focused on the measurement properties such as moisture content, color changes and longitudinal warping. The quality of beech wood is determined based on structure and properties of wood, frequency of defects in wood material. The tension wood is considered as an important wood defect causing negative...
-
The impact of drying and steaming processes on surface color changes of tension ad normal beech wood
PublikacjaThe aim of the article is to present the influence of high temperature to selected properties of beech wood (Fagus sylvatica L.). The properties such as moisture content, color changes and longitudinal warping were analyzed. The quality of beech wood is determined based on structure and properties of wood, frequency of defects in wood material. The tension wood is considered as an important wood defect causing negative alterations...
Rok 2018
-
The Effect of Full-Cell Impregnation of Pine Wood (Pinus sylvestris L.) on Changes in Electrical Resistance and on the Accuracy of Moisture Content Measurement Using Resistance Meters
PublikacjaThe impact of the full-cell impregnation of pine wood was investigated with respect to changes in electrical resistance and the accuracy of moisture content measurement. This study compared the resistance of impregnated and untreated pine timber harvested from the northern part of Poland (Pomeranian region). The wood was impregnated by the vacuum-pressure method. The preservative (TANALITH E 3475) and coloring (TANATONE 3950) agents...
Rok 2017
-
High Temperature Drying Process of Beech Wood (Fagus sylvatica L.) with Different Zones of Sapwood and Red False Heartwood
PublikacjaThis study examined the changes in the properties of beech wood (Fagus sylvatica L.) after intense drying. Beech wood with false red heartwood was selected as the test specimen. The test samples had dimensions of 50 mm thickness, 180 mm width, and 350 mm length. The specimens were divided into two groups, false red heartwood and sapwood. These specimens were selected with different angles of the growth rings (radial and tangential)....
-
The influence of the drying process on the deformation of the beech and oak wood samples
PublikacjaThe influence of the drying process conditions on the deformation of the beech and oak wood. The results of the deformation of beech wood (Fagus sylvatica L.) and oak wood (Quercus robur) after drying process are presented. The drying process was carried out in the same drying schedule for each wood species. During each of schedules 40 pieces of wood were dried. The samples were divided into two groups. The first group of tested...
Rok 2016
-
High temperature drying of beech with content of tension wood
PublikacjaThe presented artcle is focused on comparison of tension and normal wood of beech (Fagus sylvatica L.) in a high-temperature drying process. Samples of 26 mm thickness were selected from sapwood zone with different angle of growth rings. The article evaluated properties of tension and normal wood before and after drying process. Properties which are monitored were moisture, moisture gradients, covering tests, colour changes and...
-
The dying medium temperature impact on the final moisture content of pine wood at constant drying time
PublikacjaThe results of final moisture content of pine wood (Pinus sylvestris L.) after drying process are presented. The wood in the experiments was taken from the northern part of Pomeranian region in Poland. The drying process was performed in the experimental chamber equipped with the micro-jet heat exchanger. The air at temperatures of 40°C, 60°C, 80°C, 100°C and 120°C with relative humidity about 60% and atmospheric pressure was the...
-
The low temperature waste heat recovery in drying process of pine wood using micro-jet heat exchanger
PublikacjaThe article presents the influence of the drying medium temperature changes for the relative and absolute moisture content values during pine wood drying. The drying process was conducted at constant atmospheric pressure and with different drying medium (air) temperature levels, respectively: 40oC, 60oC, 80oC, 100oC, and 120oC. In order to develop a method that would enable low temperature drying of solid materials the experiments...
Rok 2015
-
The influence of high temperature wood drying conditions using air-steam mixture on its properties
PublikacjaThe results of properties change of beech wood after drying process are presented. The wood taken to experiments was from northern part of Pomeranian region in Poland. Before the main high temperature drying process using air-steam mixture, wood was initially dried in an open air conditions. The high temperature drying process was conducted at temperature 120oC, humidity 48%, flow rate of drying medium 2.5m/s and atmospheric pressure....
-
The selected effects of high temperature air-steam mixture wood drying
PublikacjaThe results of properties change of beech wood after drying process are presented. The wood taken to experiments was from northern part of Pomeranian region in Poland. Before the main high temperature drying process using air-steam mixture, wood was initially dried in an open air conditions. The high temperature drying process was conducted at temperature 120oC, humidity 48%, flow rate of drying medium 2.5m/s and atmospheric pressure....
-
Wykorzystanie ciepła niskotemperaturowego do procesu suszenia peletu ze słomy z wykorzystaniem mikrostrugowego wymiennika ciepła
PublikacjaW artykule przedstawiono wpływ temperatury medium suszącego na zmiany względnej oraz bezwzględnej zawartości wilgoci podczas suszenia peletu ze słomy. Proces suszenia przeprowadzono przy stałym ciśnieniu atmosferycznym i różnych wartościach temperatury powietrza, jako czynnika suszącego, wynoszących odpowiednio: 40℃, 60℃, 80℃, 100℃ oraz 120℃. Badania eksperymentalne wykonywano na innowacyjnym stanowisku wyposażonym w mikrostrugowy...
Rok 2014
-
Koncepcja układu sterowania pracą kotła energetycznego OP-230
PublikacjaW artykule przedstawiono koncepcję układu sterowania pracą kotła energetycznego OP-230. Dobrano odpowiednie elementy układu sterowania oraz dokonano analizy techniczno-ekonomicznej zastosowanych układów sterujących.
-
The change of mechanical properties of selected wood species after drying process under various conditions
PublikacjaThe result of mechanical properties change of selected wood species after drying process under various parameters are presented. The global elasticity modulus and bending strength for steam dried, air-steam mixture dried and air dried samples as reference were measured. It allowed to reveal the effect of wood stream, air-steam mixture and their temperature on mechanical properties of wood. It has been recognized that steam and...
wyświetlono 2668 razy