Wyszukiwarka
prof. dr hab. inż. Paweł Kłosowski
Publikacje
Filtry
wszystkich: 104
Katalog Publikacji
Rok 2023
-
Influence of cyclic frozen and defrost on mechanical properties of polytetrafluoroethylene (PTFE)-coated woven fabrics
PublikacjaThis research aims to determine the influence of the cyclic process of freezing and defrosting on the mechanical properties of the chosen glass fibres and PTFE-coated woven fabrics. The specimens were subjected to freezing at about −20 °C for 4 h and thawing by full immersion into the water at about +20 °C for 4 h. The fabric samples after 25 and 50 frozen cycles were air-dried at room temperature for one week and then subjected...
-
Influence of water soaking on the ultimate tensile strength of polyester-based coated woven fabrics
PublikacjaThis research aims to determine the influence of water-soaking on polyester-based coated woven fabrics for ultimate tensile strength and elongation at break under uniaxial tensile tests. The paper begins with a short survey of literature concerning the investigation of the determination of coated woven fabric properties. The authors carried out the uniaxial tensile tests with an application of a flat grip to establish the values...
-
Numerical and Clinical Analysis of an Eyeball Injuries under Direc Impact
PublikacjaObjectives: The objective of this study was to develop a numerical model of the eyeball and orbit to simulate a blunt injury to the eyeball leading to its rupture, as well as to conduct a comparative analysis of the results obtained using the finite element method against the clinical material concerning patients who had suffered an eyeball rupture due to a blunt force trauma. Material and Methods: Using available sclera biometric and...
-
Tensile and flexural moduli for human orbital wall bones – comparative study
PublikacjaThe main aims of the current research were: (1) to analyze in detail the tensile modulus and ultimate tensile strength (UTS) of orbital wall bones separately for the left and right orbit of the same cadaver and (2) to compare the obtained results with a flexural modulus of the left and right orbit reported earlier by A. C. van Leeuwen et al. [14]. A set of 54 specimens of orbital superior and/or medial walls harvested from 16 human...
-
Testing of Technical Fabrics under Fast Camera Control
PublikacjaThe dynamic development of measurement and recording techniques has been changing the way one conceives material strength. In this study, two different methods of evaluating the strength of fabrics are compared. The first is the typical and commonly used technique based on the use of a testing machine. The second method uses the so-called “fast camera” to monitor the entire process of the destruction of a fabric sample and analyse...
Rok 2022
-
Consideration of the safety of bungee jumping in relation to mechanical properties of the instalation based on a jump accident in Gdynia
PublikacjaThis paper considers a bungee jumping accident that took place in July 2019 in Gdynia, Poland. The authors conducted an investigation to determine the cause of the bungee rope failure. It was based on mechanical tests concerning the strength of the rope as well as the calculation of the force induced in the rope during the jump. Based on the theoretical and experimental results, the rope safety factor was estimated. It appeared...
-
Influence of Water-Induced Degradation of Polytetrafluoroethylene (PTFE)-Coated Woven Fabrics Mechanical Properties
PublikacjaThe impact of water-induced degradation on the mechanical properties of the chosen two PTFE-coated, glass threads woven fabrics is investigated in this paper. The paper begins with a survey of literature concerning the investigation and determination of coated woven fabric properties. The authors carried out the uniaxial tensile tests with an application of flat and curved grips to establish the proper values of the ultimate tensile...
-
Stress–strain model of lower corroded steel plates of normal strength for fitness-for-purpose analyses
PublikacjaThis study investigates the mechanical properties of specimens made of normal strength steel subjected to lower marine immersed corrosion degradation levels (below 25 %). The specimens were corroded in laboratory conditions, and only natural factors were controlled to raise the corrosion rate (reaching the level of 1 mm/year). Three different thicknesses of plates made of normal strength of shipbuilding steel are investigated (between...
Rok 2021
-
Cerclage cable augmentation does not increase stability of the fixation of intertrochanteric fractures. A biomechanical study
PublikacjaBackground: Intertrochanteric fractures with a posteromedial intermediate fragment are unstable because of the loss of medial support. Additional fixation with a cerclage is used in subtrochanteric fractures, but not in intertrochanteric fractures. The aim of this biomechanical study is to evaluate whether cerclage fixation improves stability of intertrochanteric fractures. Hypothesis: Our hypothesis is that the cerclage fixation...
-
On the current state of dovetail wall-corner joints in wooden Greek Catholic churches in Polish Subcarpathia with structural and sensitivity analyses
PublikacjaThis paper describes the current condition of some dovetail joints which form the wall corners of two Greek Catholic churches of wooden construction in Polish Subcarpathia. It also gives the historical background of the sacral architecture of that region. The two structures, which represent the same type of log corner joints are situated in Chotylub and Cewków. The buildings were examined e.g. for damage, wood moisture content,...
-
Tensile modulus of human orbital wall bones cut in sagittal and coronal planes
PublikacjaIn the current research, 68 specimens of orbital superior and/or medial walls taken from 33 human cadavers (12 females, 21 males) were subjected to uniaxial tension untill fracture. The samples were cut in the coronal (38 specimens) and sagittal (30 specimens) planes of the orbital wall. Apparent density (ρapp), tensile Young’s modulus (E-modulus) and ultimate tensile strength (UTS) were identified. Innovative test protocols were...
-
The cement-bone bond is weaker than cement-cement bond in cement-in-cement revision arthroplasty. A comparative biomechanical study
PublikacjaThis study compares the strength of the native bone-cement bond and the old-new cement bond under cyclic loading, using third generation cementing technique, rasping and contamination of the surface of the old cement with biological tissue. The possible advantages of additional drilling of the cement surface is also taken into account. Femoral heads from 21 patients who underwent a total hip arthroplasty performed for hip arthritis...
-
Validation of Hydraulic Mechanism during Blowout Trauma of Human Orbit Depending on the Method of Load Application
PublikacjaThe more we know about mechanisms of the human orbital blowout type of trauma, the better we will be able to prevent them in the future. As long as the buckling mechanism’s veracity is not in doubt, the hydraulic mechanism is not based on equally strong premises. To investigate the correctness of the hydraulic mechanism’s theory, two different methods of implementation of the hydraulic load to the finite element method (FEM) model...
Rok 2020
-
Artificial Thermal Ageing of Polyester Reinforced and Polyvinyl Chloride Coated Technical Fabric
PublikacjaArchitectural fabric AF9032 has been subjected to artificial thermal ageing to determine changes of the material parameters of the fabric. The proposed method is based on the accelerated ageing approach proposed by Arrhenius. 300 mm x 50 mm samples were cut in the warp and fill directions and placed in a thermal chamber at 80 °C for up to 12 weeks or at 90 °C for up to 6 weeks. Then after one week of conditioning at ambient temperature,...
-
Drill holes decrease cancellous bone strength: A comparative study of 33 paired osteoporotic human and 9 paired artificial bone samples
PublikacjaThis study was designed to compare compressive strength of cancellous bone retrieved from the femoral head in a specimen with and without guide wire hole, with comparison to synthetic bone samples. Femoral heads retrieved from 33 patients who sustained femoral neck fractures and underwent hip arthroplasty were cut into cuboids leaving two matching samples from the same femoral head. Similar samples were prepared from synthetic femurs....
-
Experimental and computational study on mechanical behaviour of carpentry corner log joints
PublikacjaThis work concerns experimental and numerical research on carpentry joints used in historic wooden buildings in southeastern Poland and western Ukraine. These structures are mainly sacred buildings, and the types of corner log joints characteristic of this region are primarily saddle-notch and dovetail joints; thus, these two types of joints were analysed in this study. The modelling of historic timber structures is a complex...
-
Nonlinear dynamic analysis of the pure “buckling” mechanism during blow-out trauma of the human orbit
PublikacjaConsidering the interplay between orbital bones and intraorbital soft tissues, commonly accepted patterns of the blow-out type of trauma within the human orbit require more thorough investigation to assess the minimal health-threatening impact value. Two different three-dimensional finite element method (FEM) models of the human orbital region were developed to simulate the pure “buckling” mechanism of orbital wall fracture in...
-
Orbital blowout trauma occurring at the workplace – clinical, biomechanical and legal aspects
PublikacjaIntroduction and objective: Craniofacial injury at the workplace may lead to orbital blowout fractures. The aim of the study is the development of own numerical model of the eye orbit, assessment of the damage zones, and comparing them with clinical examinations. In addition, the current legal status of patients after injuries is presented Material and methods: In laboratory tests performed on bones collected from the upper and...
Rok 2019
-
Influence of artificial thermal ageing on polyester-reinforced and polyvinyl chloride coated AF9032 technical fabric
PublikacjaThe presented work deals with the thermal ageing evaluation for polyester-reinforced and polyvinyl chloride coated fabrics. The architectural fabric AF9032 was exposed to artificial thermal ageing by subjecting the material samples to temperature levels of 80℃ and 90℃ for up to 12 weeks. The mechanical properties of the aged fabric have been separately described by the identified linear piecewise model (with assumption of the elastic...
-
The early failure of the gamma nail and the dynamic hip screw in femurs with a wide medullary canal. A biomechanical study of intertrochanteric fractures
PublikacjaBackground: Intertrochanteric fractures may occur in a bone with a wide medullary canal that may lead to significant mobility of a intramedullary nail, contrary to an extramedullary device. This study evaluates the Dynamic Hip Screw and the gamma nail in AO 31.A2.1 fractures in these circumstances. Methods: Synthetic femora with canals drilled to 18 mm were used. Five fixation types were examined: a 2 - hole and a 4 – hole Dynamic...
Rok 2018
-
Analysis of the cyclic load-unload-reload tests of VALMEX aged fabric
PublikacjaThe paper presents mechanical response of the VALMEX fabric during the cyclic loading-unloading and re-loading experiments. Two types of the aged material used for nearly 20 years as the roofing of the Forest Opera in Sopot (Poland) have been tested. The results have been separately obtained for the warp and fill di-rections. The comparative analysis has revealed that the material aged in service is more durable in the fill di-rection,...
-
Historical carpentry corner log joints—Numerical analysis within stochastic framework
PublikacjaThe paper presents the results of numerical analysis performed on historical, traditional carpentry corner logjoints of two basic topologies: the short-corner dovetail connection and the saddle notch connection. These types of carpentry joints are commonly used in currently preserved objects of wooden architecture. All connections have been modelled in pinewood, which has been defined in the Finite Element software MSC.Marc/Mentat...
-
Influence of service ageing on polyester-reinforced polyvinyl chloride-coated fabrics reported through mathematical material models
PublikacjaIn this paper the coupled service (constructional tension) and environmental (sunlight, rainfalls, temperature variations) ageing influence on the polyester-reinforced polyvinyl chloride (PVC)-coated fabric VALMEX is studied. Two cases of the same fabric have been analyzed: one USED for 20 years on the real construction of the Forest Opera in Sopot (Poland), and one kept as a spare material (NOT USED). The following tests have...
-
Influence of Wood Moisture on Strength and Elastic Modulus for Pine and Fir Wood Subjected to 4-point Bending Tests
PublikacjaThe main purpose of this research paper was to determine the influence of the wood moisture on the strength and elastic modulus of pine and fir wood specimens subjected to the 4-point bending tests. Six bending tests for each wood species and for two different moisture level have been performed. Then, the advanced statistical analysis of the results has been carried out. On the basis of the obtained results, it has been noted that...
-
NUMERICAL MODELLING AND EXPERIMENTATION OF HISTORICAL CARPENTRY CORNER LOG JOINTS
PublikacjaThe main purpose of this research is to determine the stress distributions on the contact surfaces between the logs of the historical carpentry corner joints. The additional purpose is to compare the stress distribution for four different boundary conditions in the case of dry and wet pine wood. The paper presents the results of numerical analysis of the shortcorner dovetail connection and the saddle notch corner joint, which are...
-
Polyester sail technical woven fabric behaviour under uniaxial and biaxial tensile tests
PublikacjaThe paper is focused on the identification of mechanical properties of a sail technical woven fabric (yacht sailcloth polyester) style 480 AP with MTO (Medium Tempered Optimized) finish. The non-linear elastic behaviour of the fabric applied for sails is investigated under uniaxial and biaxial tensile tests. Comparison of non-linear elastic parameters with others polyester coated fabrics is made. This paper is intended to be an...
Rok 2017
-
Identification of Bodner-Partom model parameters for technical fabrics
PublikacjaThe thorough analysis of modeling technical fabrics behavior with the viscoplastic Bodner-Partom constitutive law is presented. The study has been focused on differences between the warp and weft direction of the material. To obtain the model’s parameters only the uniaxial tensile laboratory tests with three different, but constant strain rates are required. The parameters have been found for polyester fibers PVC coated fabrics:...
-
Identification of Bodner-Partom Viscoplastic Model Parameters for Some Aluminum Alloys at Elevated Temperature
PublikacjaThe paper presents the identification process of inelastic (viscoplastic) properties for two aluminum alloys at a temperature of 120°C. The material parameters are calculated on the basis of uniaxial tension tests. Twelve tests at elevated temperature for each alloy have been performed—three tests for four different strain rates. The main purpose of the paper is to identify the Bodner-Partom viscoplastic model parameters for two...
-
Mechanical properties of Precontraint 1202 S2 based on uniaxial tensile and creep tests
PublikacjaThe purpose of the paper is the estimation of the polyvinyl chloride – polyester-coated fabric (Precontraint 1202 S2) mechanical properties under uniaxial tensile tests as well as short- and long-time creep tests. The uniaxial tests are the basis of non-linear elastic description while the creep tests are used for the evaluation of the stiffness parameters in time and for the identification of the standard viscoelastic model. The...
-
O obliczeniach membranowego przekrycia amfiteatru w Pruszczu Gdańskim
PublikacjaPrzedstawiono konstrukcję membranową dachu amfiteatru wykonaną z tkaniny technicznej. Opisano procedurę wykonywania prób laboratoryjnych niezbędnych do określenia nieliniowo-sprężystych właściwości tkanin technicznych oraz długotrwałej wytrzymałości na rozciąganie. Parametry materiałowe do zaprojektowania przekrycia wyznaczano na podstawie badań jednoosiowego rozciągania. Omówiono proces projektowania przekrycia z wykorzystaniem...
Rok 2016
-
Modelling of the viscoelastic properties of the technical fabric VALMEX
PublikacjaThe analysis of the Burgers model used for the constitutive description of the technical fabric VALMEX vis-coelastic behavior is presented. It has revealed that the correctness of the identification depends strongly on the level of the immediate strain taken for calculations. Moreover, it has been proven that the Burgers model can be used for modelling of the viscoelastic properties of the polyester reinforced PVC coated VALMEX...
-
Numerical analysis of the carpentry joints applied in the traditional wooden structures
PublikacjaThe paper concerns the numerical analysis of the carpentry joints made from spruce wood. The material parameters of the wood have been calculated on the basis of nine independent material constants (an orthotropic material). The contact zone between the individual elements of the connection has been determined using Contact Tables in the MSC.Marc software. Five types of carpentry joints have been analyzed. The main aim of the research...
Rok 2015
-
Podstawy obliczeń układów powierzchniowych w systemie MSC.Marc/Mentat
PublikacjaW skład prezentowanej monografii wchodzi pięć przykładów analizy elementów konstrukcyjnych wykonanych przy użyciu systemu MSC.Marc/Mentat. Każdy przykład został rozwiązany dwa razy: za pomocą klasycznej i tzw. nowej wersji interfejsu (w wersji 13.1). Przykłady opatrzono rozwiązaniami problemów wykonanymi w taki sposób, że czytelnik może uzyskać rozwiązanie danego problemu, powtarzając opisane szczegółowo instrukcje na własnym komputerze....
Rok 2014
-
Application of the Bodner-Partom constitutive equations for modelling of the technical fabric Valmex used for the hanging roof of the Forest Opera in Sopot
PublikacjaThe study of an inelastic properties of the technical fabric Valmex used for 20 years as the roof structure of the Forest Opera in Sopot (Poland) is presented. The uniaxial tensile laboratory tests with constant strain rate have been conducted and analysed. Parameters of the Bodner-Partom constitutive model have been identified and verified by numerical simulations. Two approaches of the parameters identification have been proposed:...
-
Autodesk Robot Structural Analysis = Wymiarowanie Konstrukcji Stalowych i Żelbetowych : Przyklady Obliczeń
PublikacjaW pracy przedstawiono przykłady wymiarowania konstrukcji stalowych i żelbetowych z wykorzystaniem programu Autodesk Robot Structural Analysis Professional.
-
Geometrically nonlinear analysis of shells - Benchmark problems for Autocad Robot Analysis Professional
PublikacjaThe aim of this work is to verify the suitability of commercial engineering software for geometrically nonlinear analysis of shells. This paper deals with the static, geometrically nonlinear analysis of shells made of an isotropic material. The Finite Element Method (FEM) is chosen to solve the problem. The results of the commercial software Autocad Robot Structural Analysis Professional (ARSAP) are compared with the litera-ture...
-
Influence of thermal effects on mechanical properties of PVDF-coated fabric
PublikacjaThis paper describes the method of laboratory tests necessary for identification of temperature influence on mechanical properties of polyvinylidene fluoride-coated polyester fabric often used for tensile structures. Two nonlinear model descriptions are investigated. The first one is based on the piece-wise linear relations between stress and strain and the second one on the Murnaghan model of solid behavior. This paper is proposed...
-
Mechanical properties for preliminary design of structures made from PVC coated fabric
PublikacjaIn this paper, laboratory tests necessary for the identification of non-linear elastic immediate properties of the PVC coated polyester fabric (like AF 9032) are described. The material parameters are specified on the basis of the uniaxial tensile tests in the warp and weft directions as well as on the base of the biaxial tensile tests. For the identification process techniques based on the least squares method are used. The authors...
-
Mechanical properties of polyvinyl chloride-coated fabric under cyclic tests
PublikacjaThe aim of the present paper is to propose a method of laboratory tests necessary for the identification of mechanical properties of the coated fabric. The material parameters of the coated fabric AF 9032 are specified on the basis of the uniaxial and biaxial tensile tests. For the identification process, the techniques based on the least squares methods are used. Additionally, the uniaxial and biaxial cyclic tests are performed...
-
Parameters’ Identification of Perzyna and Chaboche Viscoplastic Models for Aluminum Alloy at Temperature of 120◦C
PublikacjaThe main purpose of this paper is the parameters identification of the Perzyna and the Chaboche models for the aluminum alloy at elevated temperature. The additional purpose is comparison of the results for these viscoplastic models. The results have been verified by the numerical simulation of the laboratory tests. The material parameters have been calculated on the basis of the uniaxial tension test. The determination of the...
-
Posttraumatic Orbital Emphysema: A Numerical Model
PublikacjaOrbital emphysema is a common symptom accompanying orbital fracture. The pathomechanism is still not recognized and the usually assumed cause, elevated pressure in the upper airways connected with sneezing or coughing, does not always contribute to the occurrence of this type of fracture. Observations based on the finite model (simulating blowout type fracture) of the deformations of the inferior orbital wall after a strike in...
-
Static and dynamic modelling blow- out type trauma of orbital wall
PublikacjaAuthors of the paper present initial results of finite element analysis of a blow-out type trauma of orbital wall. The research is liked with laboratory tests for the Young’s modulus of bones evaluation. In the finite element analysis the neighbourhood of orbital wall is modelled by triangle thin shell finite elements. In the paper results of nonlinear static and transient dynamic analysis (including damping) are compared. The...
-
The 90th Birthday Jubilee of Professor Eugeniusz Bielewicz
PublikacjaOn the jubilee year of the 90th birthday of prof. Eugeniusz Bielewicz, a portrait of this eminent civil engineer and scholar is presented by his co-workers.
-
Wybrane aspekty łączenia tkanin architektonicznych na przykładzie badań tkaniny szklanej powleczonej PTFE
PublikacjaOmówiono wyniki badań połączeń zgrzewanych tkaniny szklanej pokrytej PTFE. Badania przeprowadzono jednoosiową maszyną wytrzymałościową w kierunkach wątku i osnowy z uwzględnieniem różnych szerokości spoin. Wyniki przedstawiono w postaci wykresów, a efekty zniszczenia na zdjęciach. Ustalono optymalną długość spoiny dla badanej tkaniny technicznej
Rok 2013
-
Investigation on thermal changes of mechanical properties of textile fabric of National Stadium in Warsaw roof
PublikacjaSubject of the research is investigation of mechanical properties of technical fabric Précontraint 1202 S2 used for construction of the mobile part of roof of National Stadium in Warsaw. The research has been focused on fabric behavior in low temperature conditions. The main question which had to be answer has been: is it save to open and close the roof or keep the roof in the close position in winter conditions?
-
Mechanical testing of technical woven fabrics
PublikacjaThis article presents a review of technical fabrics testing methods used by the authors on the basis of their experience with research on properties of polytetrefluoroethylene-coated fabrics used for Forest Opera in Sopot (Poland). First, the different types of testing methods used for description of mechanical properties (uniaxial tensile tests, biaxial tensile tests and shear tests) of technical woven fabrics are described. The...
-
Physical and mathematical modelling of implant-fascia system in order to improve laparoscopic repair of ventral hernia
PublikacjaThis paper describes an investigation of biomechanical behaviour of hernia repair, which is focused on the selection of safe linking of certain type of implant with fascia in laparoscopic operation. The strength of various fixations of the implant to the fascia is analysed. Methods: The research is based on experimental observations of operated hernia model behaviour during a dynamic impulse load corresponding to post-operative...
Rok 2012
-
Experimental research on technical fabric of the Forest Opera Roof in Sopot
PublikacjaThe experimental analysis of the technical fabric Valmex is presented. The study involves uniaxial tensile, cyclic, rheological and biaxial tests. Some of the main differencies between two types of the analysed material have been identified. Mechanical properties of the textile have been modeled by the viscoelastic standard model with quite good effect.
-
EXPERIMENTS AND SIMULATIONS FOR LAPAROSCOPICVENTRAL HERNIA REPAIR IMPROVEMENT
PublikacjaThe authors conducted a wide experimental and numerical study in order to determine effective approaches in the laparoscopic VH repair. At first the study covered identification of mechanical properties of the abdominal fascia, implants, tacks and transabdominalsutures. Basis on these data, the one and two-dimensional mathematical models were formulated and a number of numerical static and dynamic analyses were carried out. Then...
-
Identyfikacja gatunku stali w elementach pochodzących z rozbiórki i wykorzystywanych do wykonania konstrukcji nowego obiektu
PublikacjaWykonanie badań związanych z identyfikacją materiału zastosowanego w konstrukcji stalowej hali produkcyjnej. Badania wykonano jako nieniszczące na konstrukcji przy zastosowaniu technik spektrometrycznych i twardości. Wykonanie badań niszczących w celu identyfikacji materiału i uzyskania danych porównawczych. Wydanie rekomendacji dotyczących gatunku materiału do wykonania obliczeń statyczno - wytrzymałościowych nowej konstrukcji.
wyświetlono 4283 razy