Wyszukiwarka
Filtry
wszystkich: 1076
wybranych: 985
Wyniki wyszukiwania dla: GRAPHENE DERIVATIVES TRIBOLOGY
-
Modeling lubricant flow between thrust-bearing pads
PublikacjaInlet temperature is one of the main inputs in all models for the analysis of fluid film bearing performance. At the same time, inlettemperature distribution and also oil velocity distribution at the inlet are the result of flow phenomena in the gap between the bearingpads. These phenomena are complex and in many cases further affected by any special arrangements of forced oil supply to the gapbetween pads. The reason for such...
-
Structural properties of foil bearings: a closed-form solution validated with finite element analysis
PublikacjaFluid film thickness in a compliant foil bearing is greatly influenced by the deflection of the bearing structure. Therefore, in order to properly model performance of a foil bearing, it is mandatory that the deflection of the compliant bearing structure due to the generated hydrodynamic pressure is determined accurately. This article proposes an easy-to-use two-dimensional model, which takes into account detailed geometry of the...
-
The Innovative Research Methodology of Tribological and Rheological Properties of Lubricating Grease
Publikacja -
Characterization of NiTi SMA in its unusual behaviour in wear tests
Publikacja -
Evaluation of turning with different cooling-lubricating techniques in terms of surface integrity and tribologic properties
Publikacja -
Tribological and thermal behavior with wear identification in contact interaction of the Ti6Al4V-sintered carbide with AlTiN coatings pair
Publikacja -
Synergisms and antagonisms between MoS2 nanotubes and representative oil additives under various contact conditions
Publikacja -
Effect of ageing automotive gear oils on scuffing and pitting
Publikacja -
Technological and tribological aspects of milling-burnishing process of complex surfaces
Publikacja -
The lubricant-coating interaction in rolling and sliding contacts
Publikacja -
Tribological performance of PTFE-metal binary coatings in rolling/sliding contact
PublikacjaTribological performance of surface coatings with embedded PTFE reservoirs in rolling/sliding contact is reported. Using two different coating materials and two shapes and patterns of PTFE reservoirs test samples in the form of discs were prepared and tested in a four-ball contact configuration under loads corresponding to nominal contact pressure of 0.5 and 1.0 GPa. It was found that one coating, namely aluminium-bronze with embedded...
-
Performance of lubricated sliding contact in magnetic field
PublikacjaResults of experimental studies concerning theinfluence of permanent magnetic field on wear of lubricatedsliding contact operating at short stroke and highfrequency are presented. It was found that horizontalmagnetic is affecting performance of the contact. Thejagged delamination regions produced in the presence of amagnetic field can be regarded as easily undergoing oxidisationbecause oxygen is readily adsorbed there. Magneticfield...
-
Water-Lubricated Sintered Bronze Journal Bearings—Theoretical and Experimental Research
PublikacjaWater lubricated bearings are used from many years in shipbuilding, hydro power and other industries because of their advantages such as: extensive serviceable life, low coefficient of friction, longevity of shaft sleeve, good abrasion resistance, low maintenance required, unit simplicity, no danger of pollution and low price. Various types of water lubricated sliding bearings have been tested at the Technical University of Gdansk...
-
Environmentally acceptable lubricants (EAL) compared with a reference mineral oil as marine stern tube bearing lubricant – Experimental and theoretical investigations
PublikacjaThe purpose of this research is to indicate the potential differences in bearing characteristics resulting from the application of different lubricant types with the same viscosity grade. The effect of different environmentally acceptable lubricants (EALs) on hydrodynamic journal bearing properties is studied experimentally and compared to the properties obtained after lubrication with a reference mineral oil. The results of the...
-
Multi-objective optimization of tool wear, surface roughness, and material removal rate in finishing honing processes using adaptive neural fuzzy inference systems
PublikacjaHoning processes are usually employed to manufacture combustion engine cylinders and hydraulic cylinders. A crosshatch pattern is obtained that favors the oil flow. In this paper, Adaptive Neural Fuzzy Inference System (ANFIS) models were obtained for tool wear, average roughness Ra, cylindricity and material removal rate in finish honing processes. In addition, multi-objective optimization with the desirability function method...
-
Comparative wear test of journal sliding bearings with sintered bronze and Babbitt alloy bushes lubricated by environmentally acceptable/adapted lubricants (EAL)
PublikacjaA growing awareness of the negative effects of mineral oils on the natural environment has resulted in the introduction of new regulations related to environmental protection. One of these regulations requires the use of environmentally acceptable/adapted lubricants (EAL) to lubricate marine main shaft bearings, in place of the mineral lubricating oils that have been used for decades. Classification Societies, which supervise...
-
Temperature Measurements at Tyre Tread Rubber on Sandpaper Oscillatory Sliding Contacts Using Acicular Grindable Thermocouples
PublikacjaThe tribological performance of tyre–road contacts depends crucially on the contact temperature. This study investigates the reliability and accuracy of acicular grindable thermocouples possessing an original needle-shaped wearable part as applied to measuring temperature at the oscillatory sliding contact between a rubber tyre tread sample and a sandpaper. A linear oscillatory tribometer is used to imitate the sliding phase of...
-
Acoustic journal bearing – Performance under various load and speed conditions speed conditions
PublikacjaThe paper presents results of experimental testing aiming at finding out what effect system of piezo-electric actuators (PZTs)attached to an aerodynamic journal bearing has on the magnitude of shaft's motion within the bearing operating at specified speed and load. The results clearly demonstrate effectiveness of PZTs in mitigating the shaft's motion thus contributing to the increased stability of the bearing. This stabilizing...
-
Influence of local bush wear on water lubricated sliding bearing load carrying capacity
PublikacjaOne of main problems concerning water-lubricated bearings is their durability. There are known cases of bearings with life time measured in decades, and some, whose refurbishment was necessary just days after start-up. Obtaining stable fluid film friction plays key role in the durability of these bearings. Unfortunately, their load-carrying capacity is limited due to water's low-viscosity. The conducted experimental...
-
Acoustic journal bearing - A search for adequate configuration
PublikacjaClassical non-contact bearings are already used in a number of specialist applications but there are somespecialist areas where they cannot be used for variety of reasons and acoustic sliding bearings could be an alternative. The paper presents the quest for a configuration of an acoustic journal bearing and shows that the overall shape of the bearing and its geometry are of a vital importance for the load capacity oft he bearing....
-
Experimental research on water lubricated marine stern tube bearings in conditions of improper lubrication and cooling causing rapid bush wear
PublikacjaWater lubricated bearings are popular in sliding bearings of marine propeller shafts, turbines and pump shafts. Such popularity is partly due to their simple construction which also means a relatively affordable price. In practical experience one may also observe cases of rapid wear or even malfunctions of this bearings, some of which may be caused by insufficient flow of lubricant leading to overheating. The conducted...
-
Numerical modelling and experimental verification of compressible squeeze film pressure
PublikacjaThe validity of using the Reynolds equation for compressible squeeze film pressure was tested with computational fluid dynamics (CFD). A squeeze film air bearing was instrumented with pressure sensors and non-contacting displacement probes to provide transient measurements of film thickness and pressure. The film thickness measurements also provided input parameters to the numerical prediction. However, numerical results showed...
-
Influence of magnetic field on wear in high frequency reciprocatingsliding contacts
PublikacjaResults of experimental studies concerning the influence of permanent magnetic field on wear of dry sliding contact operating at short stroke and high frequency are presented. It was found that horizontal magnetic field with different orientations relative to the sliding direction is affecting performance of the contact. The increase in frequency of sliding reduces accumulated mass loss and lowers the surface roughness of the wear...
-
Running characteristics of aerodynamic bearing with self-lifting capability at low rotational speed
PublikacjaAn aerodynamic journal bearing that is capable of self-generating squeeze-film pressure is presented and its dynamic characteristics investigated numerically and experimentally. A numerical method based on a time marching static model was applied to assess the orbit trajectory path of the rotor upon a perturbation. Experimental results were obtained to validate the effect of the self- generated squeeze-film pressure on the stability...
-
Evaluation of apparent Young׳s modulus of the composite polymer layers used as sliding surfaces in hydrodynamic thrust bearings
PublikacjaHydrodynamic bearings with a polymer sliding layer are able to operate in severe conditions, mainly due to favorable properties of the polymers. The goal of this research was to evaluate apparent Young׳s modulus of two types of the polymer composite layers used for sliding surfaces in hydrodynamic bearings, as a function of temperature. The Young׳s modulus was evaluated on the basis of compression tests carried out on samples obtained...
-
Extended duration running and impulse loading characteristics of an acoustic bearing with enhanced geometry
PublikacjaThis paper presents performance during prolonged running of the acoustic bearing when PZTs are switched off and when they are switched on. The effect of active PZT on shaft’s displacements in X and Y directions is clearly demonstrated. Performance of the acoustic bearing was also assessed when an impulse force was applied to the running shaft at speed. Once again the benefits of having PZTs active are beyond doubt. The instability...
-
Experimental research on water lubricated three layer sliding bearing with lubrication grooves in the upper part of the bush and its comparison with a rubber bearing
Publikacjacomposite. Eachofitslayershasanimportantfunction.Speciallypreparedslidingsurfaceensures minimum resistance.Followingrunning-initssmoothnessbecomesveryhighandthebearingmay continue workingunder fluid lubricationregime.NBRlayerensuresbearingelasticity,goodvibration damping propertiesandinsusceptibilitytoshaftaxismisalignment.Theexternalbrasslayermakes fitting thebearingeasier. Experiment resultsoftheconductedresearchwerecomparedwiththoseforarubberbearingof similar...
-
Microstructure and residual stresses in surface coatings with PTFE reservoirs
PublikacjaThe paper presents the results of experimental study into the microstructure and changes in residual stresses resulting from sliding and rolling/sliding loaded interaction between metallic surface coatings with embedded PTFE reservoirs and various counter faces. It was found that before testing surface coatings had compressive residual stresses. Molybdenum coating with all types of PTFE reservoirs displayed, as a result of testing,...
-
Peculiarities associated with testing polyetheretherketone (PEEK) in a model rolling contact
PublikacjaPolyetheretherketone (PEEK) was investigated using a modified version of the four-ball tester in which the upper forth ball was replaced by a cone in such a way that kinematics of the four-ball configuration were fully preserved. Rotation of the cone enforced orbiting and rolling of the ceramic balls around the polymer cup. The results produced some unexpected peculiarities in the wear of ceramic balls which, in principle, should...
-
Properties comparison of rubber and three layer PTFE-NBR-bronze water lubricated bearings with lubricating grooves along full bush circumference based on experimental tests
PublikacjaWater lubricated bearings have been in industrial use for well over a century. During the last decade their traditional range has been expanded with new, modern products. Despite that fact, certain solutions continue to employ the standard rubber bearing with lubricating grooves located along entire bush circumference. The work presents experimental research conducted on comparable sliding bearings with lubrication grooves along...
-
Morphology of damage inflicted on brittle polymer in lubricated contact under cyclic static load
PublikacjaIn this article morphology of damage inflicted on the polymethylmethacrylate (PMMA) plate in static point lubricated contact with a ball made of five different materials under cyclic normal load has been presented. It is argued that the counterface material and lubricating film play an important role in the damage process and the extent of damage inflicted in the PMMA plate.
-
Influence of surface roughness topography on properties of water lubricated polymer bearings, experimental research
PublikacjaW artykule przedstawiono wyniki badań eksperymentalnych, których celem było zidentyfikowanie wpływu ułożenia chropowatości na powierzchni ślizgowej łożyska smarowanego wodą z polimerową panwią. Badania wykazały, że wpływ ten jest mniejszy niż oczekiwano a na własności łożyska ma wpływ głównie wysokość chropowatości.
-
Centrally Pivoted Tilting Pad Thrust Bearing with Carbon-Based Coated Collar—Experimental Results of Low- and Medium-Speed Operation
PublikacjaExperimental results of the research on a tilting pad thrust bearing with symmetrical pad support in the conditions of high loads and low speeds are presented in the paper. As described in the literature review, experimental results of tilting pad bearings at low speed/high load regime and transient conditions are rare. Unusual material selection - steel pad against a DLC-type coating on the collar was utilized. Such material combination...
-
Effect of manufacturing errors of the pad sliding surface on the performance of the hydrodynamic thrust bearing
PublikacjaIn the present study, investigation of the effect of manufacturing errors on the performance of large tilting pad thrust bearings has been performed, following a CFD-based Thermohydrodynamic analysis of a single pad. A 3D model has been generated, including the pad, the lubricant film and the corresponding part of the collar. The pad has been assumed to be deformed about the pivot point, due to thrust loading. Manufacturing errors...
-
Experimental investigation into surface texture effect on journal bearings performance
PublikacjaThe aim of this study was to analyse the performance of journal bearings with specially created dimples on the sliding surface and operating under various conditions. The texture was created on the bearing surface that co-acted with the smooth journal; moreover, the variation of the textured surface of the journal mating with the smooth bearing was tested, and the results were compared to those obtained with the standard smooth...
-
Water-lubricated stern tube bearing - experimental and theoretical investigations of thermal effects
PublikacjaThe paper presents research results of thermal phenomena accompanying operation of a water-lubricated stern tube bearing with axial grooves. Experimental tests revealed, that intensity of forced axial flow has strong influence on bush temperature. Numerical simulations focused on investigation of the thermal phenomena under operation of water-lubricated journal bearing showed, that restricted axial flow promotes backflow of the...
-
Effect of annealing temperature on slurry erosion resistance of ferritic X10CrAlSi18 steel
PublikacjaIn the present work, the slurry erosion tests were carried out to investigate the influence of heat treatment on slurry erosion process of ferritic X10CrAlSi18 stainless steel using a slurry pot test rig. X10CrAlSi18 stainless steel was tested in as-received condition and after annealing at three different temperatures: 600°C, 800°C and 1000°C. Degradation of materials due to slurry erosion depends on many factors connected with...
-
The influence of polymer bearing material and lubricating grooves layout on wear of journal bearings lubricated with contaminated water
PublikacjaThe goal of the present paper is to investigate wear properties of journal sliding bearing operating in the conditions of contaminated water lubrication. Several bearing materials and bearing sleeve designs (differing in the axial grooves position and their shape) were tested experimentally under typical operating conditions in a dedicated test rig, which was equipped with a lubricating system, enabling lubrication with contaminated...
-
Efficient Synthesis of Functionalized Unsymmetrical Dialkyl Trisulfanes
PublikacjaWe have developed a convenient method for the synthesis of functionalized unsymmetrical dialkyl trisulfanes under mild conditions in very good yields. The designed method is based on the reaction of (5,5-dimethyl-2-thioxo-1,3,2-dioxaphosphorinan-2-yl)-disulfanyl derivatives with alkyl disulfanyl anions generated in situ from S-acetyl disulfanyl derivatives and sodium methoxide. The developed method allows for the preparation of...
-
Highly effective degradation of selected groups of organic compounds by cavitation based AOPs under basic pH conditions
PublikacjaCavitation has become on the most often applied methods in a number of industrial technologies. In the case of oxidation of organic pollutants occurring in the aqueous medium, cavitation forms the basis of numerous advanced oxidation processes (AOPs). This paper presents the results of investigations on the efficiency of oxidation of the following groups of organic compounds: organosulfur, nitro derivatives of benzene, BTEX, and...
-
9,10-Dioxoanthracenyldithiocarbamates effectively inhibit the proliferation of non-small cell lung cancer by targeting multiple protein tyrosine kinases
PublikacjaAnthraquinones have attracted considerable interest in the realm of cancer treatment owing to their potent anticancer properties. This study evaluates the potential of a series of new anthraquinone derivatives as anticancer agents for non-small-cell lung cancer (NSCLC). The compounds were subjected to a range of tests to assess their cytotoxic and apoptotic properties, ability to inhibit colony formation, pro-DNA damage functions,...
-
Novel and Efficient Methods for the Synthesis of Symmetrical Trisulfides
PublikacjaWe have developed a convenient methods for the synthesis of symmetrical trisulfides under mild conditions in very good yields. The described methods are based on the straightforward preparation of 5,5-dimethyl-2-thioxo-1,3,2-dioxaphosphorinane-2-disulfanyl derivatives from readily available 5,5-dimethyl-2-sulfanyl-2-thioxo-1,3,2-dioxaphosphorinane or bis(5,5-dimethyl-2-thioxo-1,3,2-dioxaphosphorinan-2-yl) disulfide. The symmetrical...
-
TBAF Promoted Formation of Symmetrical Trisulfides
PublikacjaWe have developed a new method for the synthesis of functionalized symmetrical trisulfides based on (5,5-dimethyl-2-thioxo-1,3,2-dioxaphosphorin-2-yl)disulfanyl derivatives prepared from readily available 5,5-dimethyl-2-sul-fanyl-2-thioxo-1,3,2-dioxaphosphorinane or bis(5,5-dimethyl-2-thioxo-1,3,2-dioxaphosphorinan-2-yl) disulfide. The symmetrical trisulfides can be obtained from aliphatic and aromatic thiols andL-cysteine derivatives...
-
The smoothness test for a density function
PublikacjaThe problem of testing hypothesis that a density function has no more than μ derivatives versus it has more than μ derivatives is considered. For a solution, the L2 norms of wavelet orthogonal projections on some orthogonal ‘‘differences’’ of spaces from a multiresolution analysis is used. For the construction of the smoothness test an asymptotic distribution of a smoothness estimator is used. To analyze that asymptotic distribution,...
-
Sensorless algorithm for sustaining controllability of IPMSM drive in electric vehicle after resolver fault
PublikacjaThis paper presents a sensorless algorithm designated for the emergency control of an interior permanent magnet synchronous motor (IPMSM) drive in electric or hybrid vehicle. The algorithm is based on analysing the derivatives of motor phase currents measured over the duration of particular inverter states. The method is computationally simple and does not require additional hardware since the derivatives are measured indirectly....
-
Synthesis and steroid sulfatase inhibitory activities of N-phosphorylated 3-(4-aminophenyl)-coumarin-7-O-sulfamates
PublikacjaIn the present work, we report convenient methods for the synthesis and biological evaluation of N-phosphorylated derivatives of 3-(4-aminophenyl)-coumarin-7-O-sulfamate as potential steroid sulfatase (STS) inhibitors. Their binding modes were modeled using docking techniques. The inhibitory effects of the synthesized compounds were tested on STS isolated from human placenta. All of the newly synthesised coumarin derivatives were...
-
Opracowanie dogodnej metody tworzenia wiązań S-C o hybrydyzacji atomu węgla sp oraz sp2
PublikacjaBadania przeprowadzone w Katedrze Chemii Organicznej Wydziału Chemicznego Politechniki Gdańskiej na przestrzeni ostatnich kilku lat, pokazały wszechstronność pochodnych kwasu neopentylidenofosforoditiowego. Dotychczasowe wyniki badań doprowadziły mnie do opracowania nowych strategii syntetycznych, umożliwiających otrzymywanie związków zawierających wiązanie C-S o hybrydyzacji atomu węgla sp oraz sp2. Analizując wyniki badań opracowałam...
-
Sum-over-state expressions including second-order Herzberg–Teller effects for the calculation of absorption and resonance Raman intensities
PublikacjaThe sum-over-state expressions are derived to calculate the second-order Herzberg–Teller (HT) effects in absorption and resonance Raman spectroscopies. These effects depend on the second derivatives of the transition dipole moment with respect to the vibrational coordinates. The method is applied to the molecule of 1,3-butadiene using density functional theory calculations. It is found that the second-order HT effects are significant...
-
Modifications at the C(5) position of pyrimidine nucleosides
PublikacjaThis review summarizes the state of knowledge on the chemical methods of C(5)-modifications of uridine and cytidine derivatives and may serve as a useful tool for synthetic chemists to choose an appropriate reaction protocol. The synthesis of 5-substituted uracil derivatives is gaining an increasing interest because of their possible applications in medicine and pharmacy. Modifications at the C(5) position of pyrimidine nucleosides...
-
Approaches Towards Better Immunosuppressive Agents
PublikacjaSeveral classes of compounds are applied in clinics due to their immunosuppressive properties in transplantology and the treatment of autoimmune diseases. Derivatives of mycophe-nolic acid, corticosteroids and chemotherapeutics bearing heterocyclic moieties like methotrexate, azathioprine, mizoribine, and ruxolitinib are active substances with investigated mechanisms of action. However, improved synthetic approaches of known drugs...