Filtry
wszystkich: 1821
wybranych: 1503
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: STEEL-CONCRETE SPECIMEN
-
Underwater Welding of Duplex Stainless Steel
PublikacjaThe present work was conducted to assess the weldability of duplex stainless steel at underwater conditions. Interest of underwater welding of this steel grade is connected with necessity of preparing welding repair technologies for subsea pipelines widely used in offshore oil and gas industry. The GMA local cavity welding method was used in the investigations. Welded beads were performed underwater at 0.5 m depth and in the air....
-
Weldability of S500MC Steel in Underwater Conditions
PublikacjaWet welding with the use of covered electrodes is one of the methods of underwater welding. This method is the oldest, the most economic and the most versatile. The main difficulties during underwater wet welding are: high cooling rates of the joint, the presence of hydrogen in the arc area and formation of hard martensitic structure in the weld. These phenomena are often accompanied by porosity of welds and large number of spatters,...
-
Seismic performance evaluation of steel buckling-restrained braced frames including SMA materials
PublikacjaThe permanent deformation of the building after seismic excitations can be determined by the Maximum Residual Interstory Drift Ratio (MR-IDR), which may be used for measuring the damage states. Low-post yield stiffness of the steel buckling-restrained braced frame (BRBF) makes this system vulnerable to large MR-IDR after a severe earthquake event. To overcome this issue, this paper investigates the seismic limit state performances...
-
Degradation of ferritic X10CrAlSi18 stainless steel caused by slurry
PublikacjaThe slurry erosion tests of ferritic X10CrAlSi18 steel were carried out using a slurry pot device. In order to investigate the erosion process, two series of tests were performed: first one with a constant impact velocity of 5 m/s, 7 m/s and 9 m/s and the second one, during which the impact velocity was changed after every exposure. During each test, an influence of test conditions on volume loss, surface hardness and roughness...
-
Application of Artificial Neural Networks to Predict Insulation Properties of Lightweight Concrete
PublikacjaPredicting the properties of concrete before its design and application process allows for refining and optimizing its composition. However, the properties of lightweight concrete are much harder to predict than those of normal weight concrete, especially if the forecast concerns the insulating properties of concrete with artificial lightweight aggregate (LWA). It is possible to use porous aggregates and precisely modify the composition...
-
Influence of the Addition of Recycled Aggregates and Polymer Fibers on the Properties of Pervious Concrete
PublikacjaThe aim of the study was to check the possibility of reusing aggregate from recycled concrete waste and rubber granules from car tires as partial substitution of natural aggregate. The main objective was to investigate the effects of recycled waste aggregate modified with polymer fibers on the compressive and flexural strength, modulus of elasticity and permeability of pervious concrete. Fibers with a multifilament structure and...
-
Aesthetic perception of steel-glass architecture in Japan
PublikacjaAesthetic perception of steel-glass architecture in Japan
-
Proceedings of the fib Symposium 2019: Concrete - Innovations in Materials, Design and Structures 2019
PublikacjaDesigning a concrete mix is a process of synthesizing many components, it is not a simple process and requires extensive technical knowledge. The design process itself focuses on obtaining the required strength of concrete. Very often designing a concrete mix takes into account the need to maintain the proper water-demand and frost-resistance features. The parameters that influence the concrete class most significantly are the...
-
Mesoscopic simulations of crack propagation in concrete using cohesive elements
PublikacjaThe paper presents results of two-and three-dimensional meso-scale simulations of fracture in notched concrete beams subjected to three-point bending test. Concrete was assumed as a 3-phase material composed of aggregate grains placed in the cement matrix with Interfacial Transitional Zones (ITZs) between then. In 2D simulations macro-voids were also taken into account. The particle distribution was taken from real concrete beams...
-
INFLUENCE OF CERAMIC COATING ON MECHANICAL PROPERTIES OF STAINLESS STEEL
PublikacjaCrystal structure and phase composition of stainless steel substrates (AISI 304 type) was studied and it was found that they adopted the cubic symmetry. The calculated elementary cell parameter for the mayor Fe-Ni phase (weight fraction 99%) was a = 3.593 Å, whereas the mean grain size was = 2932 Å. Morphology of the stainless steel substrate surface was studied with profilometry. Mechanical properties of the stainless steel...
-
Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses
PublikacjaWire arc additive manufacturing (WAAM) is an additive manufacturing process based on the arc welding process in which wire is melted by an electric arc and deposited layer by layer. Due to the cost and rate benefits over powder-based additive manufacturing technologies and other alternative heat sources such as laser and electron beams, the process is currently receiving much attention in the industrial production sector. The gas...
-
The Effect of Water and Frost on Fatigue Life of Asphalt Concrete
PublikacjaThis paper presents testing of fatigue life of asphalt concrete that has been subjected to action of water and frost. Simulation of water and frost action was based on the original AASHTO T283 method and its modification. The original method was modified in such a way that instead of a single freeze-thaw cycle, 50 and 150 cycles were applied. Fatigue life was measured in the indirect tensile fatigue test in the Nottingham asphalt...
-
Influence of grout proportions on modulus of elascity of two-stage concrete
PublikacjaOmówiono badania doświadczalne przeprowadzone dla betonu dwuetapowego. Beton wykonano z kruszywa otoczakowego przy zastosowaniu trzech różnych proporcji w/c i c/p. Na drodze statystycznej opracowano prosty wzór umożliwiający wstępne szacowanie wartości siecznego modułu Younga. Ponieważ metoda dwuetapowa pozwala na zachowanie kontaktu pomiędzy poszczególnymi elementami kamiennego szkieletu wypełniającego formę, wytrzymałość uzyskanego...
-
An enhanced method in predicting tensile behaviour of corroded thick steel plate specimens by using random field approach
PublikacjaThe present work investigates the possibility of using random field techniques in modelling the mechanical behaviour of corroded thick steel plate specimens. The nonlinear Finite Element method, employing the explicit dynamic solver, is used to analyse the mechanical properties of typical specimens. A material model considering full nonlinearity is used to evaluate the stress-strain response. The influence of major governing parameters...
-
Internal imaging of concrete fracture based on elastic waves and ultrasound computed tomography
PublikacjaThe condition assessment of concrete structures belongs to the greatest challenges of non-destructive testing. Monitoring the fracture process of concrete and detecting cracks at the earliest possible stage is a vital aspect to ensure the safety of civil engineering objects. The use of ultrasound tomography enables imaging the internal structure of a tested element. This study aims at the visualization of fracture damage in concrete...
-
SIGNIFICANT GUIDELINE FOR THE DAMAGE INDICES APPLIED TO REINFORCED CONCRETE STRUCTURES
PublikacjaIn this paper, based on a deep overview and literature study, the different formulas proposed for damage indices (DIs) applied to reinforced concrete structures under monotonic or cyclic loading are classified and presented. The DIs are applied to quantify the damages to structures, ranging from zero to one. Normally, they are applied to make a decision for repairing or demolition of the structures in the post-earthquake phases. Keywords:...
-
State-of-the-art framework for high-speed camera and photogrammetric use in geometry evaluation of prestressed concrete failure process
PublikacjaPrestressed structures are a key to the realization of the boldest architectural ideas, regardless of shape complexity, great height and large span. A characteristic feature of the prestressed structure is the better use of concrete material properties by insertion of internal forces. The internal forces are opposed to external loads effects (forces and deformations of structure). Prestressed reinforced concrete beams are characterized...
-
Modeling the application of steel slag in stabilizing expansive soil
PublikacjaThe objective of this study was to evaluate the suitability of steel slag as an additive to the engineering properties of weak clay soil. Different geotechnical laboratory tests were conducted on both stabilized and natural soils. Steel slag (SS) was added at a rate of 0, 5, 10, 15, 20, and 25% to the soil. Specific gravity, grain size analysis, Atterberg limit test, compaction test, free swell, California bearing ratio (CBR),...
-
Stability analyses of a cylindrical steel silo with corrugated sheets and columns
PublikacjaW artykule przedstawiono wyniki obliczeń stateczności silosów z blachy falistej ze słupami. Wykonano analizy linowe i analizy nieliniowe stosując metody elementów skończonych. W obliczeniach uwzględniono model przestrzenny powłokowy oraz uproszczony model przestrzenny z blachy ortotropowej z belkami. Wyniki numeryczne porównano z Eurokodem.
-
Effect of admixtures on fresh grout and two-srtage (pre-placed aggregate) concrete
PublikacjaPrzedstawiono rezultaty badań doświadczalnych przeprowadzonych dla betonu uzyskanego metodą dwuetapową. Główną przeszkodą szerokiego zastosowania metody betonowania dwuetapowego Polcrete była niska wydajność urządzenia wytwarzającego mikrozaprawę - ultramiksera (UM). Celem przeprowadzonych badań laboratoryjnych było dobranie odpowiednich dodatków i domieszek, które umożliwią wytworzenie mikrozaprawy o takich samych parametrach...
-
Experimental and numerical investigations for GPR evaluation of reinforced concrete footbridge
PublikacjaThe GPR method has increasingly found application in non-destructive testing of reinforced concrete structures. This paper presents the new approach of modelling of the electromagnetic wave propagation for reinforced concrete structures with a complex system of the reinforcement. Simulations of the GPR field were performed on a three-dimensional model of a footbridge using the FDTD method. Numerical maps were compared with results...
-
Study of the Resistance to Influence of Aggressive Liquids on Concrete with Lightweight Aggregate
PublikacjaThe corrosion of the structure of concrete caused by the aggressive external environment is one of the main problems that can reduce the durability of buildings. The paper analyzes the influence of the type of component on selected properties of lightweight concrete (LWC) exposed to aggressive liquids. When lightweight concrete containing porous aggregates is used, the influence of an aggressive environment may be of particular...
-
The Influence of the Aircraft Operating Fluids on the Mechanical Parameters of the Airport Surface Concrete
PublikacjaThe authors of the article assessed the impact of operating fluids used to service aircraft on changing mechanical parameters of cement concrete intended for airport pavement. The research concerned concrete designed with the use of CEM I 42.5N LH NA low-alkali cement, broken granite aggregate, fine washed aggregate, and admixtures. The analysis included the assessment of changes in dierences in endurance parameters over various...
-
Causes of damage and methods of repairing floor made on polystyrene concrete
PublikacjaThe paper describes damages, tests and repair of the floor made on existing ceiling and expanded polystyrene concrete underlay. The floor was built on a reinforced concrete ceiling with an area of about 1050 m2. Significant damage in the form of cracks, detachments and unevenness was found in the floor. In order to determine the causes of damage, in situ tests and laboratory tests were carried out. It was found that the damage...
-
Underwater Local Cavity Welding of S460N Steel
PublikacjaIn this paper, a comparison of the mechanical properties of high-strength low-alloy S460Nsteel welded joints is presented. The welded joints were made by the gas metal arc welding (GMAW)process in the air environment and water, by the local cavity welding method. Welded joints were testedfollowing the EN ISO 15614-1:2017 standard. After welding, the non-destructive—visual, penetrant,radiographic, and ultrasonic (phased array) tests...
-
Numerical investigations on early indicators of fracture in concrete at meso-scale.
PublikacjaFracture is a major reason of the global failure of concretes. The understanding of fracture is important to ensure the safety of structures and to optimize the material behaviour. In particular an early prediction possibility of fracture in concretes is of major importance. In this paper, concrete fracture under bending was numerically analysed using the Discrete Element Method (DEM). The real mesoscopic structure of a concrete...
-
Modes of Failure Analysis in Reinforced Concrete Beam Using Laser Scanning and Synchro-Photogrammetry - How to apply optical technologies in the diagnosis of reinforced concrete elements?
PublikacjaThe following paper reveal the limitations and possibilities of terrestrial laser scanning technology adaptation in diagnostics of reinforced concrete beams. In this paper, authors present potential spectrum of TLS use in modes of failure analysis of R-C beams and determines under which conditions the laser technologies might be applied. Research was carried out at the Regional Laboratory of Structural Engineering at Gdansk University...
-
Improving Thermal Insulation Properties for Prefabricated Wall Components Made of Lightweight Aggregate Concrete with Open Structure
PublikacjaPorous concrete is commonly used in civil engineering due to its good thermal insulation properties in comparison with normal concrete and high compression strength in comparison with other building materials. An extremely porous concrete, called ‘lightweight aggregate concrete with open structure’ (LAC), is used in some German plants to produce prefabricated wall components. They are used mainly in hall buildings, e.g. supermarkets....
-
Ultrasonic diagnostics of concrete T-beams used in bridge structures
PublikacjaThis paper describes a method of ultrasonic diagnostics used for prefabricated concrete elements. The studies are focused on the applicability of nondestructive techniques based on impulse and wave packet induced elastic waves for the condition assessment of T-shaped bridge beams. Experimental tests were performed for the prestressed beam used for the superstructure of the viaduct on A1 highway near Toruń. In addition numerical...
-
Guided Wave Propagation in Detection of Partial Circumferential Debonding in Concrete Structures
PublikacjaThe following article presents results of investigating the damage detection in reinforced concrete beams with artificially introduced debonding between the rod and cover, using a non-destructive method based on elastic waves propagation. The primary aim of the research was to analyze the possible use of guided waves in partial circumferential debonding detection. Guided waves were excited and registered in reinforced concrete...
-
Joints Of Steel Sandwich Structures
PublikacjaSteel sandwich structures are perceived as alternatives to single-skin welded structures in the shipbuilding industry due its advantages like significant reduction of mass in relation to typical single skin structure. However, beside problems with their strength properties itself, applications in real structures requires of solving the problem of joining, both for connection sandwich to sandwich as well as sandwiches to single-shell...
-
Static load test on concrete pile – instrumentation and results interpretation
PublikacjaFor some time (since 8-10 years in Poland) a special static load tests on instrumented piles are carried out. Such studies are usually of a scientific nature and provide detailed quantitative data on the load transfer into the ground and characteristics of particular soil layers interaction with a pile shaft and pile base. Deep knowledge about the pile-subsoil interaction can be applied for a various design purposes, e.g. numerical...
-
A Proposed Soft Computing Model for Ultimate Strength Estimation of FRP-Confined Concrete Cylinders
PublikacjaIn this paper, the feed-forward backpropagation neural network (FFBPNN) is used to propose a new formulation for predicting the compressive strength of fiber-reinforced polymer (FRP)-confined concrete cylinders. A set of experimental data has been considered in the analysis. The data include information about the dimensions of the concrete cylinders (diameter, length) and the total thickness of FRP layers, unconfined ultimate concrete...
-
SIMULATIONS OF FRACTURE IN CONCRETE BEAMS UNDER BENDING USING A CONTINUUM AND DISCRETE APPROACH
PublikacjaThe paper describes two-dimensional meso-scale results of fracture in notched concrete beams under bending. Concrete was modelled as a random heterogeneous 4-phase material composed of aggregate particles, cement matrix, interfacial transitional zones and air voids. Within continuum mechanics, the simulations were carried out with the finite element method based on a isotropic damage constitutive model enhanced by a characteristic...
-
Investigation on Damage-Involved Structural Response of Colliding Steel Structures during Ground Motions
PublikacjaEarthquakes are the most unpredictable damaging loads which can affect civil engineering structures. Due to insufficient separation distance between adjacent structures with different dynamic properties, structural collisions may occur during ground motions. Although the research on structural pounding has recently been much advanced, the studies have mainly been conducted for concrete structures. The aim of this paper is to show...
-
Corrosion degradation impact on mechanical properties of structural steel
PublikacjaRecently, extensive research was conducted regarding the impact of corrosion degradation on the mechanical properties of structural steel. Studies show that at the material level, the microstructure is somewhat unchanged due to corrosion degradation. However, the corrosion causes pits and structural surface irregularities that consequently impact the mean stress-strain response of typical coupon specimens subjected to tensile loading....
-
Influence of Nitriding and Laser Remelting on Properties of Austenitic Stainless Steel Type X10CrNi18-8 and Cavitation Erosion Resistance
PublikacjaThe paper presents properties of surface layers. Surface layers were obtained by using low temperature glow–discharge nitriding process and laser remelting carried out on austenitic stainless steel type X10CrNi18-8. Investigations were done by using an Ultra Nanoindentation Tester (UNHT) in the Warsaw Institute of Fundamental Technological Research. The influence of the above mentioned...
-
GPR simulations for diagnostics of a reinforced concrete beam
PublikacjaThe most popular technique for modelling of an electromagnetic field, the finite difference time domain (FDTD) method, has recently become a popular technique as an interpretation tool for ground penetrating radar (GPR) measurements. The aim of this study is to detect the size and the position of damage in a reinforced concrete beam using GPR maps. Numerical simulations were carried out using the finite differ-ence time domain...
-
Remote sensing in laboratory diagnostics of reinforced concrete elements – current development and vision for the future
PublikacjaContinuous emergence of new concrete types and kinds of reinforcement, as well as technological solutions in the field of structural engineering have made great demand for diagnostic tests of reinforced concrete elements. New challenges and problems facing people require new more efficient tools for laboratory diagnostics than those commonly used. Remote sensing may be the answer to this demand. In this paper the author describes...
-
Remote sensing in laboratory diagnostics of reinforced concrete elements – current development and vision for the future
PublikacjaContinuous emergence of new concrete types and kinds of reinforcement, as well as technological solutions in the field of structural engineering have made great demand for diagnostic tests of reinforced concrete elements. New challenges and problems facing people require new more efficient tools for laboratory diagnostics than those commonly used. Remote sensing may be the answer to this demand. In this paper the author describes...
-
Production of self-compacting concrete using limestone powder
PublikacjaAlthough there are visible signs of its gradual acceptance in North Africa through its limited use in construction, Libya has yet to explore the feasibility and applicability of self-compacting concrete (SCC) in new construction. The current study revolves around SCC made of locally available materials and the harsh environmental conditions. This paper deals with the investigation into the effect of the water to powder ratio and...
-
Chemical, Physical, and Mechanical Properties of 95-Year-Old Concrete Built-In Arch Bridge
PublikacjaThis research aimed to determine the durability and strength of an old concrete built-in arch bridge based on selected mechanical, physical, and chemical properties of the concrete. The bridge was erected in 1925 and is located in Jagodnik (northern Poland). Cylindrical specimens were taken from the side ribs connected to the top plate using a concrete core borehole diamond drill machine. The properties of the old concrete were...
-
Computational Complexity and Its Influence on Predictive Capabilities of Machine Learning Models for Concrete Mix Design
PublikacjaThe design of concrete mixtures is crucial in concrete technology, aiming to produce concrete that meets specific quality and performance criteria. Modern standards require not only strength but also eco-friendliness and production efficiency. Based on the Three Equation Method, conventional mix design methods involve analytical and laboratory procedures but are insufficient for contemporary concrete technology, leading to overengineering...
-
The method of analysis of damage reinforced concrete beams using terrestial laser scanning
PublikacjaThe authors present an analysis of the possibility to assess deformations and mechanisms of destructing bent reinforced concrete beams using the terrestrial laser scanning. As part of the experiments carried out at the Regional Laboratory of Construction of the Concrete Structures Division of the Civil and Environmental Engineering Faculty at Gdansk University of Technology, the reinforced concrete beams were subjected to destruction...
-
Effect of Particle Size of Fly Ash Microspheres (FAMs) on the Selected Properties of Concrete
PublikacjaThis paper presents the investigations of selected properties of concrete containing two fractions of fly ash microspheres (FAMs) with grain size up to 200 μm and up to 500 μm. Concrete mixtures with ordinary Portland cement and three substitution rates of cement by FAMs, 1.3%, 2.0%, and 2.6%, were investigated. For all concrete mixes, the constant water–binder ratio (w/b) equal to 0.50 was used. The research program included the...
-
FEM and experimental investigations of concrete temperature field in the massive stemwall of the bridge abutment
PublikacjaThe paper deals with the prediction of early-age concrete temperature of cast-in-place stemwall of the bridge abutment. The considered object is an arch bridge located in Gda´nsk. In the case of massive structures, it is particularly important to not exceed the temperature difference between the core and the concrete surface. Too high temperature gradient generates an increase in thermal stresses, what could be the reason of exceeding...
-
Numerical modal analysis of a vertical rising steel water gate
PublikacjaVertical rising steel water gates are very common not only in Poland and Germany but also in other countries of the world. Their popularity is mainly attributed to their simplicity of construction, which makes their production process cheaper and faster when compared to other solutions. The aim of this paper is to conduct a numerical modal analysis to examine the eigenvalues and eigenmodes of a vertical rising steel gate. Two cases...
-
Cavitation Erosion of P110 Steel in Different Drilling Muds
PublikacjaThe P110 steel specimens were subjected to ultrasonic cavitation erosion in different compositions of drilling muds and surfactant additive. The test procedure was based on ASTM-G-32 standard recommendations. API 5CT-P110 steel is used for pipes in oil and gas industry. The harsh environment and high velocity of flows poses corrosive and erosive threat on materials used there. The composition of drilling fluid influences its rheological...
-
Structural Assessment of Reinforced Concrete Beams Incorporating Waste Plastic Straws
PublikacjaThe behavior of reinforced concrete beams containing fibers made of waste plastic straws (WPSs) under the three point bending test is examined. The effect of WPS fiber addition on the compressive and split tensile strength is reported. Four concrete mixes were prepared. The control mix PS-0 had a proportion of 1 cement: 1 sand: 2 coarse aggregate and a water cement ratio of 0.4. In the other three mixes PS-0.5, PS-1.5 and PS-3,...
-
Application of twin-plane ECT sensor for identification of the internal imperfections inside concrete beams
PublikacjaThe main purpose of this paper is to investigate application of special construction of Electrical Capacitance Tomography (ECT) sensor to concrete beams internal homogeneity tests. Identification of internal imperfection inside the concrete beams is one of the main problems related to analysis of the construction structure bearing capacity. Therefore, this paper shows attempts to study the measurement prospects for this non-invasive,...