Wyszukiwarka
Wyniki wyszukiwania dla: concrete design
-
The long-term properties of mineral-cement-emulsion mixtures
PublikacjaThis publication presents evaluation of long-term behavior of mineral-cement-emulsion (MCE) mixtures. MCE mixtures are among the major products of cold recycling of old asphalt pavements. They are composed by binding of the old materials reclaimed from the pavement and new mineral aggregate using two different binding agents – cement and bituminous emulsion. While bituminous emulsion dissolutes and binds materials quite fast, it...
-
Measurements of Thermal Conductivity of LWC Cement Composites Using Simplified Laboratory Scale Method
PublikacjaThe implementation of low-energy construction includes aspects related to technological and material research regarding thermal insulation. New solutions are sought, firstly, to reduce heat losses and, secondly, to improve the environment conditions in isolated rooms. The effective heat resistance of insulating materials is inversely proportional to temperature and humidity. Cement composites filled with lightweight artificial...
-
Probabilistic seismic assessment of RC box-girder highway bridges with unequal-height piers subjected to earthquake-induced pounding
PublikacjaThis paper uses the probabilistic seismic assessment to study the effects of pounding and irregularity on the seismic behavior of typical concrete box-girder bridges with four levels of altitudinal irregularity. To extend the results for all bridges in the same class, uncertainty related to the earthquake, structural geometries, and materials are considered. Pounding is likely to take place in two cases: the first one concerns...
-
Automated Reasoning Based User Interface
PublikacjaMotivation: The ability to directly trace how requirements are implemented in a software system is crucial in domains that require a high level of trust (e.g. medicine, law, crisis management). This paper describes an approach that allows a high level of traceability to be achieved with model-driven engineering supported by automated reasoning. The paper gives an introduction to the novel, automated user interface synthesis in...
-
Results of acoustic emission tests of corrosion protection degree of ship steel tanks covered by means of protective coatings (Phase I)
PublikacjaThis paper presents methods and results of the 1st series of tests of acoustic emission (AE) signals, aimed at assessing degree of corrosion protection of a tank made of hull structural steel, protected by means of a protective coating combined from polyurethane layer and concrete filler. The tests were carried outin compliance with a method specially elaborated for application to the work in question. In the method were used requirements...
-
Seismic damage diagnosis in adjacent steel and RC MRFs considering pounding effects through improved wavelet-based damage-sensitive feature
PublikacjaThis paper aims to propose complex Morlet (cmorfb-fc) wavelet-based refined damage-sensitive feature (rDSF) as a new and more precise damage indicator to diagnose seismic damages in adjacent steel and Reinforced Concrete (RC) Moment Resisting Frames (MRFs) assuming pounding conditions using acceleration responses. The considered structures include 6- and 9-story steel and 4- and 8-story RC benchmark...
-
Dietary behaviour and physical activity policies in Europe: learnings from the Policy Evaluation Network (PEN)
PublikacjaThe European Policy Evaluation Network (PEN), initiated in autumn 2018, aimed at advancing the evidence base for public policies impacting dietary behaviour, physical activity and sedentary behaviours in Europe. This is needed because non-communicable diseases—the leading cause of global mortality—are substantially caused by physical inactivity and unhealthy dietary behaviours, which in turn are driven by upstream factors that...
-
Damage-involved response of two colliding buildings under non-uniform earthquake loading
PublikacjaPounding between insufficiently separated buildings, which may result in considerable damage or may even lead to the total collapse of colliding structures, has been repeatedly observed during earthquakes. Earthquake-induced collisions of buildings has been intensively studied applying various structural models. It was assumed in the analyses, however, that the seismic excitation is identical for all structural supports; whereas,...
-
Pile Model Tests Using Strain Gauge Technology
PublikacjaOrdinary pile bearing capacity tests are usually carried out to determine the relationship between load and displacement of pile head. The measurement system required in such tests consists of force transducer and three or four displacement gauges. The whole system is installed at the pile head above the ground level. This approach, however, does not give us complete information about the pile-soil interaction. We can only determine...
-
The use of lightweight aggregate saturated with PCM as a temperature stabilizing material for road surfaces.
PublikacjaThis paper presents the possibility of adding lightweight building aggregates to increase the stability – mechanical as well as thermal - of constructions and road objects. This stability can be achieved through saturating the porous granules of aggregate with a phase-change material (PCM) that allows the accumulation of solar heat. Intense solar radiation, especially during the summer, can cause the asphalt on road surfaces, bridges...
-
Impact performance of novel multi-layered prepacked aggregate fibrous composites under compression and bending
PublikacjaMulti-layered Prepacked aggregate fibrous composite (MLPAFC) is a new type of concrete, which is prepared in two subsequent stages of aggregate-fibre skeleton prepacking and cementitious grouting. In this study, ten MLPAFC mixtures were prepared in three subsequent layers incorporating different contents of four different types of steel fibres. Long and short hooked-end and crimped steel fibers were adopted with 3.0 and 1.5% dosages...
-
Generating actionable evidence from free-text feedback to improve maternity and acute hospital experiences: A computational text analytics & predictive modelling approach
PublikacjaBackground Patient experience surveys are a key source of evidence for supporting decision-making and quality improvement in healthcare services. These surveys contain two main types of questions: closed and open-ended, asking about patients’ care experiences. Apart from the knowledge obtained from analysing closed-ended questions, invaluable insights can be gleaned from free-text data. Advanced analytics techniques are increasingly...
-
Composite as a Material of the Future in the Era of Green Deal Implementation Strategies
PublikacjaComposite materials have become synonymous with modernity, desired in nearly every aspect of our daily lives, from simple everyday objects to sanitary facilities, pipelines, the construction of modern sewer networks, their renovation, water supply, and storage reservoirs, to complex structures—automotive, planes, and space science. Composites have seen a considerable rise in attention owing to their characteristics, durability,...
-
Guided waves for nondestructive diagnostics of embedded waveguides
PublikacjaThe thesis concentrates on comprehensive theoretical, numerical and experimental analysis of guided wave propagation in bars embedded in concrete or mortar. The investigations are focused on a particular type of objects representing a laboratory model of a ground anchor. Complex description of wave propagation phenomena in partially embedded bars is given and its application in...
-
ASSESSMENT OF CLIFF STABILITY AFTER THE DEMOLITION OF THE ENGINEERING FACILITIES
PublikacjaAs a part of an experiment, cliff in Gdynia Redlowo (southern coast of Baltic Sea, Gdansk Bay) was measured using terrestrial laser scanner. The main reason for taking up the subject of the Orlowo Cliff’s stability was a decision about controlled removal one of the war fortification elements. The main purpose of that analysis was to specify suitability of laser scanning in determination of slope’s stability after a violent event....
-
BARWIENIE BETONU - PRAKTYCZNE WSKAZÓWKI cz 2
PublikacjaProdukcja barwionych elementów wibroprasowanych w niewielkim stopniu różni się od wykonawstwa zwykłych, szarych elementów betonowych. Przy stosowaniu pigmentu w postaci płynu należy uwzględnić dodatkową ilość wody wprowadzaną do mieszanki betonowej (40 ÷ 60 % objętości pigmentu płynnego). Płynna postać pigmentu umożliwia bezpyłowe i wygodniejsze dozowanie. Zdarza się jednak, że wytrąca się w nich osad, gdy zawiesina pozostaje...
-
BARWIENIE BETONU - PRAKTYCZNE WSKAZÓWKI cz 1
PublikacjaProdukowane w Polsce i importowane pigmenty stosowane w produkcji betonu barwionego są wysokoprocentowymi tlenkami żelaza. Są to substancje bezwonne, nietoksyczne i niepalne. Cechują się wysoką jakością w zakresie intensywności barwienia, zdolnością krycia i łatwością rozprowadzania w suchych mieszankach. Oferta rynkowa pigmentów jest bardzo bogata. Pigmenty dostępne są w postaci płynnej, granulatu lub proszku. Możliwe jest...
-
Modelling of Asphalt Mixes under Long Time Creep at Low Temperatures
PublikacjaProper description of asphalt mixtures behavior under long time load is one of the most important factors in analyses of strain and stress relations at low temperatures both from traffic and environmental loads. For example different models of thermal stress accumulation require different approaches of description of asphalt concrete. But in all cases it is required to describe its behavior under long time loading, which in some...
-
Poroelastic Road Surfaces - State of The Art
PublikacjaPoroelastic Road Surfaces (PERS) constitute a specific group of pavements containing a great amount of crumbled rubber. In most cases rubber aggregate constitutes about 20% of the mixture (by weight) and a polyurethane resin is used as a binder. As a result, PERS is characterized by a much higher elasticity than asphalt and a high porosity typical for drainage pavements. Due to this, tire/road noise is greatly reduced and on top...
-
Robert Jankowski prof. dr hab. inż.
OsobyUrodził się 26 grudnia 1968 r. w Gdyni. Absolwent Liceum Ogólnokształcącego przy Konsulacie PRL w Benghazi, Libia (1987), student Politechniki Gdańskiej (studia magisterskie jednolite, 1987-1991 i 1992-1993), Uniwersytetu w Sheffield, Anglia (studia inżynierskie, 1991-1992), Uniwersytetu w Roskilde, Dania (kurs magisterski, 1993) oraz Uniwersytetu Tokijskiego, Japonia (studia doktoranckie, 1994-1997). Od początku pracy zawodowej...