Wyszukiwarka
Filtry
wszystkich: 31
Wyniki wyszukiwania dla: BEECH WOOD
-
EFFECT OF PRESS DRYING ON DIMENSION STABILITY AND DENSITY OF BEECH WOOD,
PublikacjaTimber is traditionally dried in kilns by processes that often take several days or weeks to complete. At present, it is possible to apply several methods of rapid drying of timber, including, for example, press drying. This research is based on the use of this process. Drying was performed using the heating plates with a temperature of 160 °C. Three pressures were compared in the research 1.0 MPa, 1.4 MPa, and 1.8 MPa. The density...
-
Impact of high temperature drying process on beech wood containing tension wood
PublikacjaThe technology of high temperature drying has a great inuence on dimensional and selected physical changes in tension wood. Article is focused on the measurement properties such as moisture content, color changes and longitudinal warping. The quality of beech wood is determined based on structure and properties of wood, frequency of defects in wood material. The tension wood is considered as an important wood defect causing negative...
-
Effect of the Drying Method of Pine and Beech Wood on Fracture Toughness and Shear Yield Stress
PublikacjaThe modern wood converting processes consists of several stages and material drying belongs to the most influencing future performances of products. The procedure of drying wood is usually realized between subsequent sawing operations, affecting significantly cutting conditions and general properties of material. An alternative methodology for determination of mechanical properties (fracture toughness and shear yield stress) based...
-
The impact of drying and steaming processes on surface color changes of tension ad normal beech wood
PublikacjaThe aim of the article is to present the influence of high temperature to selected properties of beech wood (Fagus sylvatica L.). The properties such as moisture content, color changes and longitudinal warping were analyzed. The quality of beech wood is determined based on structure and properties of wood, frequency of defects in wood material. The tension wood is considered as an important wood defect causing negative alterations...
-
The effect of beech wood (Fagus sylvatica L.) steaming process on the colour change versus depth of tested wood layer
PublikacjaThe results of experimental research on the colour changes of beech wood at different depths of the tested layer are presented. Beech wood (Fagus sylvatica L.) dried in a conventional kiln was tested. Half of the wood samples were steamed prior to the drying process. Colour changes were measured at various depths after the face milling process was used to remove the material to expose to the deeper surface. The colour changes were...
-
Predicting cutting power for band sawing process of pine and beech wood dried with the use of four different methods
PublikacjaWood drying is an important stage in the woodworking process. After drying, wood is subject to a re-sawing process, for which a high quality surface, low material loss, and high efficiency are often required. In this paper, forecasted values were presented of cutting power for the re-sawing process of pine and beech wood that were dried with four different methods. Forecasting of cutting power for an industrial band saw machine...
-
Cutting power estimation of the bandsawing process of beech wood (Fagus sylvatica L.) dried in three operating modes
PublikacjaIn this paper the predicted values of cutting power for bandsawing machine (ST100R, f. Stenner), which is located at the sawmill company Complex in Dziemiany, were presented. The values of cutting power were forecasted for beech wood (Fagus sylvatica L.), from the northern part of Pomerania region in Poland, which was dried in three operating modes: BKP - air drying at 25oC, BKS - air-steam mixture drying at 80oC, BKW - steam drying...
-
High Temperature Drying Process of Beech Wood (Fagus sylvatica L.) with Different Zones of Sapwood and Red False Heartwood
PublikacjaThis study examined the changes in the properties of beech wood (Fagus sylvatica L.) after intense drying. Beech wood with false red heartwood was selected as the test specimen. The test samples had dimensions of 50 mm thickness, 180 mm width, and 350 mm length. The specimens were divided into two groups, false red heartwood and sapwood. These specimens were selected with different angles of the growth rings (radial and tangential)....
-
High temperature drying of beech with content of tension wood
PublikacjaThe presented artcle is focused on comparison of tension and normal wood of beech (Fagus sylvatica L.) in a high-temperature drying process. Samples of 26 mm thickness were selected from sapwood zone with different angle of growth rings. The article evaluated properties of tension and normal wood before and after drying process. Properties which are monitored were moisture, moisture gradients, covering tests, colour changes and...
-
The influence of the drying process on the deformation of the beech and oak wood samples
PublikacjaThe influence of the drying process conditions on the deformation of the beech and oak wood. The results of the deformation of beech wood (Fagus sylvatica L.) and oak wood (Quercus robur) after drying process are presented. The drying process was carried out in the same drying schedule for each wood species. During each of schedules 40 pieces of wood were dried. The samples were divided into two groups. The first group of tested...
-
The effect of thermal modification on the quality of the milled surface of beech and pine wood
PublikacjaThe article deals with the effect of thermal modification on the quality of the created surface during milling on CNC milling cutters. The quality of the created surface is evaluated based on surface roughness, specifically its roughness parameter Ra. The observed surface is created by a shank cutter with a diameter of 20 mm and three cutting edges in a spiral at a standard speed of 18,000. min-1. The article compares thermally...
-
Deformation and Surface Color Changes of Beech and Oak Wood Lamellas Resulting from the Drying Process
PublikacjaThe drying process was examined relative to parameters’ influence on the deformation and surface layer color changes of beech wood (Fagus sylvatica L.) and oak wood (Quercus robur L.). The goal was to analyze the impact of drying process conditions, wood and growth rings types, and load on the deformation and surface color changes of drying thin wooden elements. A further aim was to reduce the time of the lamella drying and minimize...
-
Influence of drying mode and feed per tooth rate on the fine dust creation in pine and beech sawing on a mini sash gang saw
PublikacjaThe experimental results of the study focused on the effect of drying processes of modified air drying and warm air steam mixture drying of pine and beech wood on the size of sawdust particles created in cutting using PRW-15M sash gang saw, are presented in the paper. Particle size analysis of dry sawdust was performed using two methods—sieving method and laser diffraction analysis. The results showed that the drying process did...
-
The influence of drying parameters on wood properties
PublikacjaResults of influence of gas-steam mixture drying process on wood mechanical properties are presented. Wood species, namely pine (Pinus sylvestris L.) and beech (Fagus silvatica L.) from the northern part of Pomerania region in Poland, were subject of steam kiln-drying process in a laboratory kiln specially arranged for that reason.
-
The Effect of Steaming Beech, Birch and Maple Woods on Qualitative Indicators of the Surface
PublikacjaThis work presents the effect of steaming beech, birch and maple woods on the resulting quality of the milled wood surface. The steaming process of the studied woods results in a targeted change in the color of the wood, which changes from the original light white-gray color to fine reddishbrown to dark brown color shades that are more or less saturated depending on the temperature of the saturated water steam. The color changes...
-
THE EFFECT OF WOOD DRYING METHOD ON THE GRANULARITY OF SAWDUST OBTAINED DURING THE SAWING PROCESS USING THE FRAME SAWING MACHINE
PublikacjaThe experimental results of the study focused on the effect of drying processes of warm air drying at the temperature of 6580°C and warm air-steam mixture drying at the temperature of 105°C of pine and beech wood to the size of sawdust grains created by cutting using RPW 15M frame saw is presented in the paper. Particle size analysis of dry sawdust was performed using two methods - screening method and optical method based on...
-
Preliminary studies on the effect of feed speed on the colour change of wood
PublikacjaThis paper presents the results of preliminary analyses of the effect of cutting parameters on changes in the colour of wood. Beech wood cut with use circular saw was analysed. The cutting parameter tested was the feed speed, represented by the feed per tooth. Sawing processes with different feed per tooth ranging from 0.0008 mm to 0.09 mm were analysed. It was observed that over the entire range of feed rate per tooth analysed,...
-
Moisture content during and after high- and normal-temperature drying processes of wood
PublikacjaThe aim of the article is to present the results of moisture content of wood during and after the high-temperature steam and air–steam mixture drying processes and after an open air-drying process. The knowledge of moisture content changes of wood in the process of its drying is one of the important parameters to economy drying process and to keep the quality of dried wood. Wood samples, namely, spruce (Picea abies K.) and beech...
-
The selected effects of high temperature air-steam mixture wood drying
PublikacjaThe results of properties change of beech wood after drying process are presented. The wood taken to experiments was from northern part of Pomeranian region in Poland. Before the main high temperature drying process using air-steam mixture, wood was initially dried in an open air conditions. The high temperature drying process was conducted at temperature 120oC, humidity 48%, flow rate of drying medium 2.5m/s and atmospheric pressure....
-
Influence of high temperature air-steam mixture application on time wood drying process
PublikacjaThe results of influence gas-steam mixture drying process on time wood drying process are presented. Wood species, namely oak (Quercus L.), beech (Fagus L.), pine (Pinus L.) and spruce (Picea K.) from the northern part of Pomerania region in Poland, were subject of air-steam mixture drying process. Main focus of those tests was to shorten the time of drying process and afterward to check properties of wood.
-
Hydrogen production from wood waste by mean of dark fermentation
PublikacjaThe utilization of wood wastes in clean and green chemistry method like by mean of dark fermentation, is a highly desired solution of waste management. In the article model for the estimation hydrogen potential of wood waste is given. The model has been used to calculate the potential theoretical hydrogen mass that can be produced from wood wastes in Pomerania and Silesia: pine, spruce, fir, beech and oak. In the introduction,...
-
Influence of steam drying process on wood mechanical properties
PublikacjaResults of influence of gas-steam mixture drying process on mechanical properties of material are presented. Wood species, namely oak (Quercus L.), beech (Fagus L.), pine (Pinus L.) and spruce (Picea K.) from the northern part of Pomerania region in Poland, were subject of air-steam mixture drying process in a laboratory kiln especially arranged for that reason. Measurements of the global coefficient of elasticity and bending strength...
-
The influence of high temperature wood drying conditions using air-steam mixture on its properties
PublikacjaThe results of properties change of beech wood after drying process are presented. The wood taken to experiments was from northern part of Pomeranian region in Poland. Before the main high temperature drying process using air-steam mixture, wood was initially dried in an open air conditions. The high temperature drying process was conducted at temperature 120oC, humidity 48%, flow rate of drying medium 2.5m/s and atmospheric pressure....
-
Sawing Processes as a Way of Determining Fracture Toughness and Shear Yield Stresses of Wood
PublikacjaA new computational model, based on fracture mechanics, was used to determine cutting forces. Unlike traditional computing methods, which depend on many coefficients reflecting the machining of solid wood, the new model uses two main parameters: fracture toughness and shear yield stresses. The aim of this study was to apply this new method to determine these parameters for the tooth cutting edge principal positions and longitudinal...
-
AN INNOVATIVE APPROACH TO PREDICTION ENERGETIC EFFECTS OF WOOD CUTTING PROCESS WITH CIRCULAR-SAW BLADES
PublikacjaIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. The aim of the paper is to present a new calculating model using the application of modern fracture mechanics and to compare cutting parameters of native beech, Bendywood...
-
By-Products from Food Industry as a Promising Alternative for the Conventional Fillers for Wood–Polymer Composites
PublikacjaThe present paper describes the application of two types of food-industry by-products, brewers’ spent grain (BSG), and coffee silverskin (ŁK) as promising alternatives for the conventional beech wood flour (WF) for wood–polymer composites. The main goal was to investigate the impact of partial and complete WF substitution by BSG and ŁK on the processing, structure, physicochemical, mechanical, and thermal properties of resulting...
-
Fracture Toughness and Shear Yield Strength Determination for Two Selected Species of Central European Provenance
PublikacjaWhen offcut of wood is formed by shearing, Atkins’s analyses of sawing processes can be applied. Using this modern approach, it is possible to determine the fracture toughness and shear yield strength of wood. This model is only applicable for the axial-perpendicular cutting direction because both of these parameters are suitable for the given direction of cutting edge movement and cannot be considered material constants. Alternatively,...
-
Revisiting the estimation of cutting power with different energetic methods while sawing soft and hard woods on the circular sawing machine: a Central European case
PublikacjaIn the classical approaches, used in Central Europe in practice, cutting forces and cutting power in sawing processes of timber are commonly computed by means of the specific cutting resistance kc. It needs to be highlighted that accessible sources in handbooks and the scientific literature do not provide any data about wood provenance, nor about cutting conditions, in which cutting resistance has been empirically determined. In...
-
Comparison of Downdraft and Updraft Gasification of Biomass in a Fixed Bed Reactor
PublikacjaThe aim of this study was to compare and analyze the gasification process of beech wood. The experimental investigation was conducted inside a gasifier, which can be operated in downdraft and updraft gasification system. The most important operating parameter studied in this paper was the influence of the amount of supply air on the temperature distribution, biomass consumption and syngas calorific value. The results show that...
-
Outcomes of gynecologic cancer surgery during the COVID-19 pandemic: an international, multicenter, prospective CovidSurg-Gynecologic Oncology Cancer study
Publikacja -
Effect of COVID-19 pandemic lockdowns on planned cancer surgery for 15 tumour types in 61 countries: an international, prospective, cohort study
Publikacja