Wyszukiwarka
Filtry
wszystkich: 33
Wyniki wyszukiwania dla: EUROCODE 7
-
Report of Eurocode 7 application for pile foundation design in Poland
PublikacjaThe EC7 rules of geotechnical design are in use in Poland for several years, even though there is no National annex. With regard to pile foundations, there are valid EC7 recommendations concerning design approaches, load partial coefficients, correlation coefficients and capacity partial coefficients. Polish designers can be quite flexible when it comes to choose a method for static, bearing capacity and settlement calculations....
-
Determination of Earth Pressure and Displacement of the Retaining Structure According to the Eurocode 7-1
PublikacjaComparative analysis of standard guidelines and findings given in EC7-1 and in Polish Standard PN-83/B-03010. Discussed guidelines concerning active and passive earth pressure as well as at rest pressure state. Wall displacement causing limit states of earth pressure and resistance. Interactive assumptions concerning intermediate earth pressure and resistance values. Conclusions and final remarks.
-
Fundamenty palowe, obliczenia z zastosowaniem zasad Eurokodu 7 i doświadczeń krajowych
PublikacjaPrzedstawiono zagadnienia obliczania fundamentów palowych w nawiązaniu do zaleceń Eurokodu 7. Zwrócono uwagę, że zgodnie z założeniami Eurokodu 7, projektant i inżynier ma swobodę w wyborze metod obliczeniowych.Przytoczono i zarekomendowano metody i propozycje miedzy innymi obliczania statycznego układów palowych, określania nośności pali, prognozowania osiadań fundamentów palowych oraz charakterystyk obciążenie-osiadanie pali...
-
Stan graniczny użytkowalności konstrukcji oporowych z gruntu zbrojonego geosyntetykami – analiza wytycznych projektowych
PublikacjaSprawdzenie stanu granicznego użytkowalności konstrukcji oporowej z gruntu zbrojonego. Możliwości wyznaczenia przemieszczeń konstrukcji. Porównanie podejść projektowych według zaleceń Eurokodu 7, instrukcji ITB 429/2007, BS 8006, EBGEO i FHWA.
-
Application of the ‘CPT 2012’model of AFNOR standard for column design in Poland–Jazowa case study
Publikacjahis paper presents the ‘CPT 2012’ model incorporated into the AFNOR NF P94-262:2012-07, French standard for pile design fully compatible with Eurocode 7, to the wider Polish audience. The bearing capacity of three reference columns for Vistula Marshlands have been calculated according to ‘CPT 2012’ model and AFNOR recommendations. Then, the design resistances have been compared with ultimate column bearing capacity measured during...
-
PRELIMINARY FIELD TESTS AND LONG-TERM MONITORING AS A METHOD OF DESIGN RISK MITIGATION: A CASE STUDY OF GDAŃSK DEEPWATER CONTAINER TERMINAL
PublikacjaAppropriate risk assessment plays a fundamental role in the design. . The authors propose a possible method of design risk mitigation, which follows recommendations included in Eurocode 7. The so-called “Observational Method” (OM) can produce savings in costs and programmes on engineering projects without compromising safety. The case study presented is a complex design solution that deals with the heavy foundations of a gantry...
-
INFLUENCE OF TIME ON THE BEARING CAPACITY OF PRECAST PILES
PublikacjaOne of the most popular types of foundations in layered subsoil with very differentiated soil shear strengths are precast piles. One of the reasons is a fact that we can well control the driving process during the installation of these piles. The principles of the assessment of bearing capacity and settlements of the piles given by Eurocode 7, concentrate on two main methods, i.e. Static Pile Load Tests (SPLT) and Dynamic Driving...
-
Stability of cylindrical steel silos composed of corrugated sheets and columns based on FE analyses versus Eurocode 3 approach
PublikacjaComprehensive static and dynamic 3D stability finite element analyses of a cylindrical steel silo composed of corrugated sheets and open thin-walled vertical stiffener profiles were carried out by taking the geometric and material non-linearity into account. The silowas subjected to axisymmetric and non-axisymmetric loads imposed by a bulk solid following Eurocode 1. Theoretical and measured initial geometric imperfections were...
-
Axial capacity of steel built-up battened columns
PublikacjaThis paper deals with the numerical investigation aimed to study the axial capacity of pin-ended steel built-up columns. Three methods of calculating forces in chords and batten, taking into account the material and geometric imperfections specified in the Eurocode 3 are considered. The aim of this study was to compare different methods allowing the calculation of the column load capacity and determine a simpler and faster method...
-
Influence of Actual Curing Conditions on Mechanical Properties of Concrete in Bridge Superstructures
PublikacjaThis article presents the research on the mechanical characteristics of concrete in the construction of three concrete bridges. A system of recording the internal temperature of concrete and automatic control of laboratory ovens was used for specimen curing. This allowed the specimens to be cured under conditions similar to those occurring in the structure. Before the construction, reference blocks were used to define similar curing...
-
Load-carrying capacity of axially loaded concrete-filled steel tubular columns made of thin tubes
PublikacjaAn experimental investigation was conducted on 30 CFST columns. An influence of the following factors on load-carrying capacity of the investigated columns was analyzed: the column slenderness (l1 = 42, l2 = 27 and l3 = 15), the tube thickness (the reinforcement ratio was equal to 4% or 6%), the way of applying the load to CFST columns (through the concrete core or through the entire cross-section), the bond strength between a...
-
Simplified stability analysis of steel cylindrical silos with corrugated walls and vertical columns
PublikacjaIn the paper a simplified stability analysis of steel cylindrical silos composed of corru¬gated walls and vertical open-sectional columns was proposed. The whole 3D silo was modeled as a single column resting on elastic foundation provided by the silo walls. In proposed formula for the calculation of the foundation stiffness the curvature of the silo walls was taken into account. Three different analyses were carried out using...
-
Buckling Analysis of Cold Formed Silo Column
PublikacjaThe paper is devoted to stability analysis of different models of steel cold formed silo column. The steel cylindrical silos are often composed of corrugated walls and vertical open-sectional columns uniformly placed along the silo circumference. Both the whole 3D silo, a simplified model consisting of one column with a part of the silo walls, and a single column resting on elastic foundation provided by the silo walls were analyzed....
-
Numerical analysis on axial capacity of steel built-up battened columns
PublikacjaThis paper deals with the numerical analysis aimed at study the bearing capacity of pinended steel built-up columns under axial compression. Finite element (FE) models were performed for the columns presented in the literature. The main problem discussed in the article is the shape and magnitude of geometric imperfections introduced into the numerical FE model, necessary to obtain the load capacity consistent with the experimental...
-
Application of linear buckling sensitivity analysis to economic design of cylindrical steel silos composed of corrugated sheets and columns
PublikacjaThe paper deals with global stability of steel cylindrical silos composed of corrugated walls and vertical columns with loads imposed by a bulk solid following Eurocode 1. The optimum silo design with respect to the steel weight was based on a sensitivity analysis method. The changes of silo column profiles at each design step were performed by means of influence lines for the buckling load factor due to the unit column bending...
-
Graniczne stopnie zbrojenia poprzecznego elementów żelbetowych według normy europejskiej i polskiej
PublikacjaW pracy przeprowadzono zbiorczą analizę ogólnych metod wyznaczania minimalnego i maksymalnego stopnia zbrojenia na ścinanie elementów żelbetowych. Na tym tle dokonano porównania zaleceń normy europejskiej Eurocode 2 i normy polskiej PN-B-03264:2002, a także przedstawiono wyniki ilościowe dla elementów o wysokościach od 0,20 do 0,60 m.
-
Stability of truss with side - supports. The case of linear and rotational elastic supports
PublikacjaThe research is devoted to study lateral buckling of truss with linear and rotational elastic side-supports. Geometrically nonlinear analysis of example truss with linear and rotational elastic sidesupports is carried out. The limit normal force in compressed chord of the truss due to stiffness of side supports is calculated. The elastic support reaction in relation to force in compressed chordand coefficient of buckling length...
-
Stability of roof trusses stiffened by corrugated sheets
PublikacjaThe present parametric study is devoted to the stability analysis of a set of trusses stiffened by decking of corrugated steel sheets. For different parameters of corrugated sheets the critical loading of the roof is calculated. In the parametrical analysis the threshold bracing condition of the roof is obtained. Then the geometrically non-linear analysis of trusses braced by corrugated sheets was conducted. As a results of non-linear...
-
ECONOMICAL AND SAFE METHOD OF GRANULAR MATERIAL STORAGE IN SILOS IN OFFSHORE PORT TERMINALS
PublikacjaThe article discusses issues related with storage of granular materials in silos made of corrugated sheets and reinforced with vertical ribs. Advantages and disadvantages of these structures are named, and typical technological solutions used by largest silo producers are presented. Moreover, basic assumptions of Eurocode 3 are discussed in the context of determining the buckling load capacity of a ribbed jacket. Alternative methods...
-
O minimalnym zbrojeniu poprzecznym elementów żelbetowych.
PublikacjaProblematyka prawidłowego określenia minimalnego zbrojenia poprzecznego w strefach przypodporowych konstrukcji żelbetowych jest wciąż kontrowersyjna. Zagadnienie jest złożone, gdyż w problematyce tej należy uwzględnić wiele istotnych parametrów, które trudno jest w sposób prosty opisać. W pracy przedstawiono podstawowe zależności, które należy uwzględnić celem prawidłowego opisania w/w zjawiska, a także podano wzory określające...
-
Wpływ sztywności podpór bocznych na nośność kratownic dachowych
PublikacjaPrzeprowadzono analizę numeryczną wpływu sztywności podpór bocznych kratownicy dachowej na jej nośność w zakresie sprężystym. Zastosowano nieliniową analizę problemu wprowadzając dwa warianty modelu konstrukcji: z imperfekcjami geometrycznymi na podstawie normy PN-90/B-03200 oraz z imperfekcjami obciążeniowymi na podstawie Eurocode 3: Design of Steel Structures . Wyznaczono siły w stężeniach oraz porównano je z odpowiednimi zaleceniami...
-
Analysis of sloping brace stiffness influence on stability and load bearing capacity of a truss
PublikacjaThe paper is focused on the numerical study of stability and load bearing capacity of a truss with side elastic braces. The structure is made in reality. The rotational and sliding brace stiffnesses were taken into account. Linear buckling analysis and non-linear static analysis with geometric and material nonlinearity were performed for the beam and shell model of the truss with respect to the angle of sloping braces. As a result...
-
ANALYSIS OF BRACE STIFFNESS INFLUENCE ON STABILITY OF THE TRUSS
PublikacjaThe paper is devoted to the numerical and experimental research of stability of a truss with side elastic supports at the top chord. The structure is a model of a real roof truss scaled by factor ¼. The linear buckling analysis and non-linear static analysis were carried out. The buckling length factor for the compressed top chord was calculated and the limit load for the imperfect truss shell model with respect to brace stiffness...
-
Analysis of EN 1993-1-6 guidelines about determining amplitudes of equivalent imperfections of steel cylindrical shells subjected to uniform external pressure
PublikacjaCivil engineering structures should be designed with reference to relevant standards. One of them is a Eurocode 3 standard EN 1993-1-6:2007: Design of steel structures Part 1-6: Strength and Stability of Shell Structures. According to this standard, the value of buckling load can be determined using different approaches: classical hand calculations (stress design) and geometrical and material non-linear analysis of an imperfect...
-
Investigation of stability and limit load of a truss overhead opened bridge
PublikacjaThe paper presents selected methods of determining stability and limit load of a truss top chord in opened bridges. These methods include linear buckling and non-linear static analysis based on the finite element method and algorithms based on design code procedures. The described methods were tested on an example of a steel footbridge situated in Straszyn. The results of stability analysis are compared. The results of geometrical...
-
Stability and load bearing capacity of a braced truss under upward wind loading
PublikacjaThe paper is focused on the numerical and experimental investigation of stability of a steel truss under upward wind loading. The structure was stiffened by elastic braces situated at the top and bottom chord. Usually the lateral (translational) brace stiffness is considered. However, the rotational stiffness of braces caused by interaction between torsional stiffness of the truss top chord and bending stiffness of the roof elements...
-
Stability and load bearing capacity of a braced truss under upward wind loading
PublikacjaThe paper is focused on the numerical and experimental investigation of stability of a steel truss under upward wind loading. The structure was stiffened by elastic braces situated at the top and bottom chord. Usually the lateral (translational) brace stiffness is considered. However, the rotational stiffness of braces caused by interaction between torsional stiffness of the truss top chord and bending stiffness of the roof elements...
-
Concrete-filled FRP tubular members in marine and bridge structures
PublikacjaConcrete core of the concrete-filled tubes (CFTs) with circular cross-section is in the case of an axial compression subjected to a spatial state of compressive stresses. This state leads to enhancement in the concrete strength. The enhancement is utilized in Eurocode 4 design procedures for CFSTs (i.e. CFTs with tube made of steel). The structural design of CFFTs (i.e. CFTs with tube made of Fibre Reinforced Polymer - FRP) is...
-
Experimental Studies of Concrete-Filled Composite Tubes under Axial Short- and Long-Term Loads
PublikacjaThe paper presents experimental studies on axially compressed columns made of concrete-filled glass fiber reinforced polymer (GFRP) tubes. The infill concrete was C30/37 according to Eurocode 2. The investigated composite pipes were characterized by different angles of fiber winding in relation to the longitudinal axis of the element: 20, 55 and 85 degrees. Columns of two lengths, 0.4 m and 2.0 m, were studied. The internal diameter...
-
Buckling resistance of a metal column in a corrugated sheet silo - experiments and non-linear stability calculations
PublikacjaThe results of experimental and numerical tests of a single corrugated sheet silo column’s buckling resistance are presented in this study. The experiments were performed in a real silo with and without bulk solid (wheat). A very positive impact of the bulk solid on the column buckling resistance occurred. The experimental results were first compared to the buckling resistance calculated by Eurocode 3 formulae. The comparison revealed that...
-
Experimental investigation of joint with positive eccentricity in CFS truss
PublikacjaDue to technological restrictions, in the case of trusses made of CFS open cross-sections, positive eccentricities in the truss joints have become very frequent. Therefore studies concerning the load-bearing capacity of truss joints with positive eccentricity were undertaken. It was assumed that the resistance of cold-formed steel (CFS) open cross-section truss joints located on compression chords and with positive eccentricity...
-
Rzeczywista nośność pali w gruntach ilastych z zastosowaniem zaleceń PN-EN 1997-1:2004
PublikacjaObecnie co raz więcej obiektów posadawianych jest w gruntach słabych bądź o specyficznych parametrach, do takich gruntów zalicza się iły. Jedną z podstawowych możliwości posadowienia w gruntach ilastych jest posadowienie na palach. Projektowanie fundamentów na palach dla takich warunków wymaga specjalnego i indywidualnego podejścia. W pracy przedstawiono przegląd metod i uwag w oparciu o PN-EN 1997-1:2004, którymi należy kierować...
-
Dariusz Kowalski dr inż.
Osoby