Publikacje
Filtry
wszystkich: 1206
wyświetlamy 1000 najlepszych wyników Pomoc
Katalog Publikacji
-
Three-dimensional fractographic analysis of total fracture areas in 6082 aluminium alloy specimens under fatigue bending with controlled damage degree
Publikacja -
Effect of manufacturing errors of the pad sliding surface on the performance of the hydrodynamic thrust bearing
PublikacjaIn the present study, investigation of the effect of manufacturing errors on the performance of large tilting pad thrust bearings has been performed, following a CFD-based Thermohydrodynamic analysis of a single pad. A 3D model has been generated, including the pad, the lubricant film and the corresponding part of the collar. The pad has been assumed to be deformed about the pivot point, due to thrust loading. Manufacturing errors...
-
Metal Foams as Novel Catalyst Support in Environmental Processes
Publikacja -
Recent advances in electrochemically surface treated titanium and its alloys for biomedical applications: A review of anodic and plasma electrolytic oxidation methods
PublikacjaNowadays, titanium and its alloys are widely used materials in implantology. Nevertheless, the greatest challenge is still its appropriate surface treatment in order to induce optimal properties, which facilitates formation of a permanent bond between the implant and human tissue. The use of electrochemical treatment such as anodic oxidation or plasma electrolytic oxidation allows for the production of porous coating that mimics...
-
Quasistatic and fatigue behavior of an AISI H13 steel obtained by additive manufacturing and conventional method
Publikacja -
Abrasion Resistance of S235, S355, C45, AISI 304 and Hardox 500 Steels with Usage of Garnet, Corundum and Carborundum Abrasives
Publikacja -
Strain sequence effect on fatigue life and fracture surface topography of 7075-T651 aluminium alloy
Publikacja -
Simulation of large thrust-bearing performance at transient states, warm and cold start-up
PublikacjaThe start-up of a large hydrodynamic thrust bearing of a vertical hydrogenerator is one of the most critical situations during the lifetime of a bearing. Hydrodynamic load capacity is low due to low speed and higher thermal deformations of the pad. A new approach to the simulation of a hydrodynamic bearing is shown in this article. A combination of finite elements method and computational fluid dynamics is used to perform the transient...
-
Rolling resistance and tyre/road noise on rubberised asphalt pavement in Poland
PublikacjaThe paper presents results of tyre/road noise and rolling resistance measurements performed on stone mastics asphalt (SMA) that contains rubberised asphalt, developed and produced by a refinery in Poland. Bituminous binder was modified with polymer and addition of crumb rubber. The first observations of asphalt mixture with the new kind of modified bitumen used on the field section are presented. Rolling resistance of passenger...
-
Modeling lubricant flow between thrust-bearing pads
PublikacjaInlet temperature is one of the main inputs in all models for the analysis of fluid film bearing performance. At the same time, inlettemperature distribution and also oil velocity distribution at the inlet are the result of flow phenomena in the gap between the bearingpads. These phenomena are complex and in many cases further affected by any special arrangements of forced oil supply to the gapbetween pads. The reason for such...
-
Vibration surveillance supported by Hardware-In-the-Loop Simulation in milling flexible workpieces
PublikacjaW artykule przedstawiono nowoczesne podejście do problemu minimalizacji poziomu drgań podczas frezowania szybkościowego elementów podatnych. Do analizy dynamicznej procesu skrawania zastosowano niestacjonarny model opisany we współrzędnych hybrydowych. Na tej podstawie, przy wykorzystaniu energetycznego wskaźnika jakości wyprowadzono opis sygnału sterującego. Sygnał ten jest następnie stosowany do aktywnej redukcji drgań przedmiotu...
-
Wave propagation in delaminated beam
PublikacjaW pracy przedstawiono model oraz wyniki analizy propagacji fali sprezystejw belce z delaminacją.
-
Partition of friction heat between sliding semispaces due to adhesion-deformational heat generation
PublikacjaAnalytical expressions of heat-partition coefficient and contact temperatures for two sliding semispaces with account for adhesion-deformational heat generation and contact heat exchange have been obtained. The rate of deformational heat generation is assumed to decay exponentially with increase of distance from the interface. It has been shown that heat-generation configuration and the intensity of contact heat exchange have impact...
-
Energy-based fatigue failure characteristics of materials under random bending loading in elastic-plastic range
Publikacja -
Effect of presence of lifting pocket on the THD performance of a large tilting-pad thrust bearing
PublikacjaHydrostatic assistance is a commonly used method to improve limited load carrying ability of tiltingpad thrust bearings during transient states of operation of vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves, etc.), it also requires manufacturing of special recesses/pockets at pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up...
-
Stress Monitoring System for Individuals with Autism Spectrum Disorders
PublikacjaIn this article, a stress monitoring system tailored for individuals with Autism Spectrum Disorders (ASD) and developed for the educational institution is presented. People with ASD face problems with effective stress management due to their high self-perceived levels of stress, poor ability to cope with it, and dificulties with the accurate detection of the source of stress. Consistently, being able to measure stress appears to...
-
Detection of Delamination in Laminate Wind Turbine Blades Using One-Dimensional Wavelet Analysis of Modal Responses
PublikacjaThis paper demonstrates the effectiveness of a nondestructive diagnostic technique used to determine the location and size of delamination in laminated coatings of wind turbine blades. This is realized based on results of numerical and experimental investigations obtained by the use of the finite element method (FEM) and laser scanning vibrometry (LSV). The proposed method is based on the one-dimensional continuous wavelet transform...
-
Optimal control of 2-wheeled mobile robot at energy performance index
PublikacjaThe paper presents the application of the optimal control method at the energy perfor- mance index towards motion control of the 2-wheeled mobile robot. With the use of the proposed method of control the 2-wheeled mobile robot can realise effectively the desired trajectory. The problem of motion control of mobile robots is usually neglected and thus performance of the realisation of the high level control tasks is limited.
-
Effect of Nitrogen Ion Implantation on the Cavitation Erosion Resistance and Cobalt-Based Solid Solution Phase Transformations of HIPed Stellite 6
Publikacja -
Correlations between the wear of car brake friction materials and airborne wear particle emissions
PublikacjaAirborne wear particles emitted from transport vehicle brakes are one of the main sources of toxic metals in inhalable particulate matter. Prediction of wear particle emissions may become more accurate if the relationship between the wear and particle emission characteristics is known. An experimental study was performed to investigate proportional correlations between the mass wear, 0.01–0.42 μm particle emission measured by a NanoScan...