Search
Filters
total: 590
filtered: 548
Search results for: COMPRESSION IGNITION ENGINES
-
DME as alternative fuel for compression ignition engines – a review
PublicationThe ecological issues and the depletion of crude oil, has led the researchers to seeking for non-petroleum based alternative fuels, along with more advanced combustion technologies, and after-treatment systems. The use of clean alternative fuels is the one of the most perspective method that aiming at resolving of the said issues. One of the promising alternative fuels that can be used as a clean highefficiency compression ignition...
-
Possibility to use engine compression ignition engines in floating power plants marine
PublicationCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. The engines can be used in power industry for electricity generation in a simple or combined steam turbine system in combined heat and power plants. The leading engine in such an arrangement is an internal-combustion piston engine. The main propulsion engines are used in large piston internal-combustion engines...
-
ECU calibration for gaseous dual fuel supply system in compression ignition engines
PublicationThe dual fuel (DF) combustion mode is proven solution that allows to improve or get at the same level engine performance and reduce toxic compounds in exhaust gases which is confirmed by researchers and end-users. DF combustion mode uses two fuels gaseous fuel as a primary energy source and a pilot quantity of diesel fuel as ignition source. However, in order, to fully take advantage of the potential of the dual fuel mode, DF system...
-
An Investigation into Cold Start Emissions from Compression Ignition Engines using EU Legislative Emissions Test Procedures
Publication -
The concept of research on ecological, energy and reliability effects of modified marine fuel oils application to supply compression-ignition engines in real conditions
PublicationWithin the article, basic assumptions of the research project financed by Regional Fund for Environmental Protection and Water in Gdansk were described. The project concerns the experimental investigations carried out on laboratory compression-ignition engine in conditions of its supply with a non-standard marine fuel oil. Configuration and measuring capability of laboratory test bed presently being constructed were introduced....
-
Experiments on compression ignition engine powered by nano-fuels
PublicationThe use of nanoparticles in fuels provides new opportunities for modification of fuel properties, which may affect the operational parameters of engines, in particular the efficiency and fuel consumption. The paper presents comparison of compression ignition engine performance fuelled with neat diesel and nano-diesel. Alumina (Al2O3) was used as nanoparticles. Surface-active substances, including Span 80 surfactant, as well as...
-
A probabilistic concept of load assessment of self-ignition engines
PublicationPrzedstawiono propozycję probabilistycznej interpretacji obciążenia silników spalinowych o zapłonie samoczynnym. Zaproponowano probabilistyczny opis obciążenia tych silników z uwzględnieniem znanych parametrów (wskaźników) ich pracy. Wykazano, że obciążenie tego rodzaju silników, rozpatrywane w dowolnej chwili, może być uważane za zmienną losową. Zwrócono uwagę, że obciążenie to może być uważane za zmienną losową wielowymiarową....
-
Simulation of ammonia combustion in dual-fuel compression-ignition engine
Publication -
Diagnostic model of compression-ignition engine slide bearings for controlling the changes of their state
PublicationW artykule przedstawiono koncepcję umożliwiającą sterowanie procesami zmian stanów eksploatacyjnych silnika na podstawie modelu diagnostycznego łożysk ślizgowych. Jako model łożyska ślizgowego przyjęty został topologiczny model diagnostyczny, pozwalający na pełne i dokładne wykorzystanie oleju smarowego jako jednego z nośników informacji o stanie technicznym łożyska. Przedstawiona została przykładowa interpretacja stanów eksploatacyjnych...
-
Statistic and probabilistic measures of diagnosis likelohood on the state of self-ignition combustion engines
PublicationW artykule zaproponowano, aby wiarygodność diagnozy o stanie technicznym silników o zapłonie samoczynnym była rozpatrywana jako losowa cecha tej diagnozy. Wykazano możliwość oceny wiarygodności diagnozy za pomocą liczb rzeczywistych z przedziału [0, 1]. Uzasadniono potrzebę rozróżniania wiarygodności diagnozy i trafności diagnozy. Wyprowadzono wzór na prawdopodobieństwo sformułowania prawidłowej diagnozy jako miary wiarygodności...
-
The use of Acoustic Emission to identification damages bearings the main and crank engines about the automatic ignition
PublicationThe article describes the laboratory tests, which make the first stage of the study concerning the use of the AE method to determine the technical state of the slide bearings in engines with self-ignition. The aim of the present tests was to compare the recorded signals in relation to the technical state of the material of the bearing bush and to check the possibility of using the AE method in determining the transition moment...
-
Cold Start Emissions of Spark-Ignition Engines at Low Ambient Temperatures as an Air Quality Risk
Publication -
POSSIBILITY OF IDENTIFICATION OF TECHNICAL CONDITION OF BEARINGS FOR SELF-IGNITION ENGINES BY APPLICATION OF ACOUSTIC EMISSION AS A DIAGNOSTIC SIGNAL
PublicationThis paper presents the results of empirical studies where the acoustic emission (AE) method was applied to identify the technical condition of sliding surfaces of main and crank bearings for main diesel engines. The test results indicate that the measurements of the AE parameters allow the technical condition identification for bearings of this type. The results refer to the measurements of the parameters for AE generated in the...
-
A probabilistic concept of assessment of amount of noxious substances contained in exhaust gas emitted from self-ignition engines
PublicationPrzedstawiono probabilistyczną koncepcję oceny toksyczności spalin silników o zapłonie samoczynnym. Ocena taka jest istotna, ponieważ bez niej nie jest możliwe określenie walorów proekologicznych różnych środków transportowych z napędem spalinowym, w tym śródlądowych statków pasażerskich. W koncepcji tej uwzględniony został model procesu rozruchu silników o zapłonie samoczynnym. Model ten przedstawiono w formie procesu semimarkowskiego,...
-
The Impact of Fuel Ethanol Content on Particulate Emissions from Light-Duty Vehicles Featuring Spark Ignition Engines
Publication -
HEALTH MONITORING OF A COMPRESSION IGNITION ENGINE FED WITH DIFFERENT LOW-SULPHUR MARINE FUELS BY ENDOSCOPIC IMAGE PROCESSING AND ANALYSIS
PublicationThis article characterises the methodology for the endoscopic testing of a laboratory diesel engine used for testing marine fuels. The ‘Shadow’ measurement method used in the XLG3 type EVEREST digital endoscope, for quantitative and qualitative identification of detected surface defects, was approximated. Representative endoscopic images of the elements limiting the working space of the research engine are demonstrated, having...
-
Particulate Emissions from European Vehicles Featuring Direct Injection Spark Ignition Engines Tested Under Laboratory Conditions
Publication -
Impacts of Using Exhaust Gas Recirculation and Various Amount of Dimethyl Ether Premixed Ratios on Combustion and Emissions on a Dual-Fuel Compression Ignition Engine
PublicationIn the presented research, the authors dealt with the specific properties of the combustion process of dimethyl ether (DME) in a combustion car (Volkswagen Golf IV) engine AJM 1.9 TDI PDE made by Volkswagen factory. Dimethyl ether is an alternative fuel produced most often from natural gas, which can be used in compression ignition engines as a single fuel or co-burned with diesel oil. This work describes the impacts of using exhaust...
-
A CONCEPT OF DETERMINING THE RELATION BETWEEN LOAD AND WEAR OF TRIBOLOGICAL SYSTEMS OF SHIP MAIN SELF-IGNITION ENGINES BY USING PROBABILISTIC APPROACH PROBABILISTIC APPROACH
PublicationThis paper presents a proposal of simultaneous consideration of load and wear associated with it , of tribological systems of ship main engines (intended for ship propulsion) . Based on results of investigations it was assumed that both the load Q (i.e. a cause of wear ) and the wear Z (i.e. an effect of load occurrence) considered in a given time t(0 ≤ t ≤ t) are random variables Qt and Zt, respectively. There was characterized...
-
Low Ambient Temperature Cold Start Emissions of Gaseous and Solid Pollutants from Euro 5 Vehicles featuring Direct and Indirect Injection Spark-Ignition Engines
Publication -
Adoption of the F-statistic of Fisher-Snedecor distribution to analyze importance of impact of modifications of injector opening pressure of a compression ignition engine on specific enthalpy value of exhaust gas flow
PublicationThis article analyzes the effect of modifications of injector opening pressure on the operating values of a compression ignition engine, including the temperature of the fumes. A program of experimental investigation is described, considering the available test stand and measurement capabilities. The structure of the test stand on which the experimental measurements were conducted is presented. The method of introducing real modifications...
-
Feasibility of combined diesel engine - steam turbine in power station operating in the maritime
PublicationCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. Currently, the efficiency of such engines amounts to 45-50%. With such a large power unit, exhaust gases leaving the engine contain very large quantities of heat available for further treatment. Exhaust gases from the piston engine contain about 25% of the heat supplied to the engine in the fuel. Using the...
-
Analysis and assessment of the acoustic emission suitability for determination of the energy states of a tribological system in the form of a four-ball tester friction node
PublicationThe present operating safety and cost reduction requirements of the compression ignition engines make it necessary to search for new methods of detecting their defects, e.g. by the analysis of acoustic emission signals coming from the slide bearings. The paper presents non-destructive measurements of acoustic emission (AE) in order to obtain information on the processes taking place in a tribological system under the continuously...
-
ISSUES OF ECONOMIC ANALYSIS OF ELECTRIC ENERGY GENERATION IN A FLOATING POWER PLANT
PublicationThis article presents basic dependences for conducting a technical and economic analysis related with investment projects. It describes a combined system of a compression ignition engine and a steam turbine, whose aim, when placed on a floating platform, is to generate electric energy in the so-called distributed generation system. Such a system involves a reciprocating internal combustion engine and a connected steam turbine system...
-
Laboratory station for research of the innovative dry method of exhaust gas desulfurization for an engine powered with residual fuel
PublicationContemporary methods of exhaust gas desulfurization in marine engines are all expensive methods (4-5 million euro). This is, among other reasons, due to the limited market audience, but primarily due to the monop-olized position of manufacturers offering fabrication and assembly of this type of marine ship installations. Proposed as part of a research project financed by the Regional Fund for Environmental Protection and Maritime...
-
Operational problems of large power diesel engines combusting biofuels, considered togetherwith assessment of their operation
PublicationWithin this article the issue of large power self ignition engines fed with biofuels has been undertaken. The analysis focused mainly on operation problems. There has been noticed some advantages and difficulties associated with the biofuel application to self ignition engines. The research problem has been characterised and the research purposes have been proposed enabling the most profitable formation of energetic features of...
-
Endoscopic image processing and analysis of pistons' service failures of marine diesel engines
PublicationThe paper deals with diagnostic issues concerning endoscopic examinations of working spaces within marine diesel engines. In the beginning, endoscopy apparatus being on laboratory equipment of the Department of Ship Power Plants of Gdansk University of Technology has been characterized. The endoscopy considerations have been focused on theoretical bases of a digital image processing and especially - on the "Shadow" measurement...
-
Methodology for determining the elemental composition, as well as energy and ignition properties of the low-sulfur marine fuels
PublicationThe key metrological issue of substance and energy balance in research engines is the precise determination of the elemental composition of the applied fuel and its net calorific value. This makes it possible to calculate the amount of heat brought with the fuel into the combustion chamber, as well as the amount and gas composition of the exhaust. However, to fully assess the energy quality of the fuel used, its ignition properties...
-
Evaluation of the significance of the effect of the active cross-sectional area of the inlet air channel on the specific enthalpy of the exhaust gas of a diesel engine using statistics F of the Fisher-Snedecor distribution
PublicationThis paper presents the application of Fisher-Snedecor distribution F statistics to assess the significance of the influence of changes in the active cross-sectional area of the inlet air channel (Adol) flow in a diesel engine on the observed diagnostic parameter determined on the basis of measurements of the quick changing exhaust gas temperature in the outlet channel, which is the specific enthalpy of the exhaust gas stream within...
-
Application of the F-statistic of the Fisher-Snedecor distribution to analyze the significance of the effect of changes in the compression ratio of a diesel engine on the value of the specific enthalpy of the exhaust gas flow
PublicationThe paper discusses the impact of changes in the compression ratio on the operating parameters of a diesel engine, e.g. on the temperature of exhaust gases. It presents the construction of the laboratory test stand, on which experimental measurements were realized. It is characterized how the actual changes of the compression ratio were introduced to the existing engine. The program of experimental investigations taking into account...
-
Analysis of catalitic reactors usefulness to reduce pollution generated by piston combustion engines with regard to ship main engines
PublicationThe article presents results which indicate that the use of catalytic reactors to reduce emissions of harmful compunds contained in the exhaust gas is important in the operation of vehicle motors operation. Efforts of the shipbuilding industry to reduce the toxicity of exhaust gas emitted by the main engines have been indicated and pointed to the desirability of the use of these catalysts in maritime transport. It has been pointed...
-
Fuel systems of high power stationary engine
PublicationThe use of alternative fuels and, in the future, synthetic fuels has forced changes in the design of fuel supply systems in internal combustion engines. When operating a stationary engine at constant load, the possibility of using lean fuel mixtures appears. The selection of a precise operating mixture ignition system requires changes in traditional fuel systems. The article presents the current designs of fuel supply systems and...
-
Conception for diagnosing SI engines fed with biofuel in operation conditions
PublicationThe article deals with the question of diagnosing the high power self ignition (SI) engines fed with pro-ecologic fuels in an aspect of appearing operation problems. There has been presented the specific of action and techno-operation profile of the combustion engine foreseen as an investigations object. The preliminary conception of diagnostic investigations of the engine 7L35MC type produced in H. Cegielski - Poznan S.A. factory...
-
Modeling of the internal combustion engine cooling system
PublicationThe article concerns computer modelling of processes in cooling systems of internal combustion engines. Modelling objectives and existing commercial programs are presented. It also describes Author’s own method of binding graphs used to describe phenomena in the cooling system of a spark ignition engine. The own model has been verified by tests on the engine dynamometer. An example of using a commercial program for experimental...
-
LEGAL ASPECTS OF ELECTRIC ENERGY GENERATION IN A FLOATING POWER PLANT
PublicationThis paper discusses the characteristics of pollution and legal regulations governing investment projects affecting the environment. It describes a combined system of a compression ignition engine and a steam turbine, whose aim, when placed on a floating platform, is to produce electric energy in a so-called distributed generation system. Such a system involves a reciprocating internal combustion engine and a connected steam turbine...
-
Analysis of pressure ratio in the intake in dependence on high-voltage behaviours
PublicationPower control in spark ignition engines by regulating the intake air is performed. The control unit needs information about the air pressure conditions which then enters the combustion chamber. The information about the intake air pressure is an important quantity for optimal control of combustion mixtures. The paper describes some types of sensors that are used to measure the air intake temperature. Air pressure in the intake...
-
Ocena wpływu dawki DME na wybrane wskaźniki procesu spalania w dwupaliwowym silniku o zapłonie samoczynnym
PublicationPrzedmiotem rozprawy jest analiza wpływu różnej ilości odparowanego DME wprowadzonego do kolektora dolotowego na wybrane wskaźniki spalania DME/ON dla wielu punktów pracy, turbodoładowanego silnika o zapłonie samoczynnym. Jako punkty pracy silnika, wybrano punkty najbardziej reprezentujące cykl jazdy WLTP dla samochodu Volkswagen Golf IV. Analizę procesu współspalania przeprowadzono z wykorzystaniem danych pomiarowych, uzyskanych...
-
Te use of acoustic emission for assessment of the oil lubricity in a four-ball tester
Publicationin view of the increased dynamic and temperature load in the compression-ignition engine tribological systems, particular attention is drawn to the problem of such lubrication of the friction nodes that after breaking the boundary layer it could be restored without any wear occurring. therefore, an idea has been devised of introducing to friction nodes, with the lubrication oils, of new substances (operational preparations) modifying...
-
Dimethyl ether (DME) as potential environmental friendly fuel
PublicationIn recent years, there has been a growing interest in replacing petroleum fuels with so-called second generation environmental friendly fuels. Compared to traditional petroleum fuels dimethyl ether (DME) could be used as a clean high-efficiency compression ignition fuel with reduced particulate matter (PM), sulfur oxides (SOx), hydrocarbons (HC), carbon monoxide (CO) as well as combustion noise. Compared to some of the other leading...
-
DIAGNOSTIC INFORMATION ANALYSIS OF QUICKLY CHANGING TEMPERATURE OF EXHAUST GAS FROM MARINE DIESEL ENGINE PART I SINGLE FACTOR ANALYSIS
PublicationIn this paper, attention was paid to the problem of low controllability of marine medium- and high-speed engines during operation, which significantly limits the parametric diagnosis. The measurement of quickly changing temperature of engine exhaust gas was proposed, the courses of which can be a source of diagnostic information. The F statistic of the Fisher-Snedecor distribution was chosen as a statistical tool. Laboratory tests...
-
An experimental assessment on a diesel engine powered by blends of waste-plastic-derived pyrolysis oil with diesel
PublicationThe utilization of plastic solid wastes for sustainable energy production is a crucial aspect of the circular economy. This study focuses on pyrolysis as an effective method to convert this feedstock into renewable drop-in fuel. To achieve this, it is essential to have a comprehensive understanding of feedstock composition, pyrolysis process parameters, and the physicochemical characteristics of the resulting fuel, all correlated...
-
Analysis of balancing of four stroke V6 engines
PublicationAnalysis of balance of V6 engines with a common-pin crankshaft depending on a cylinder bank angle and the crank radius to connecting rod length ratios , based on the relations derived, is presented in the paper. The bank angles providing the lowest moment of inertia forces in reciprocating motion, for selected values, were determined. The position of the plane of the main counterweights in order to maximum balance of the moment...
-
Comparative analysis of balancing of V6 engines with common- and split-pin crankshafts
PublicationAn analysis of balancing of V6 engines equipped with split-pin crankshafts with any cylinder bank angle based on the mathematical relations derived in the paper was carried out. A comparison of the quality of their balancing with engines equipped with common-pin crankshafts was also carried out. The bank angle ranges beneficial for balancing of moments of inertia forces in reciprocating motion were determined. A mathematical relation...
-
Stirling engines - the state of technology development and computational models
PublicationStirling engines represent a technologically important solution in combined heat and power systems. Their use enables the achievement of over 90 percent efficiency in the management of the primary energy source with a very high durability of the device, mainly due to the lack of contact of the working gas with external factors and a very small number of mechanical components. The use of a Stirling engine may be equally important...
-
Thermodynamic modeling of combustion process of the internal combustion engines – an overview
PublicationThe mathematical description of combustion process in the internal combustion engines is a very difficult task, due to the variety of phenomena that occurring in the engine from the moment when the fuel-air mixture ignites up to the moment when intake and exhaust valves beginning open. Modeling of the combustion process plays an important role in the engine simulation, which allows to predict incylinder pressure during the combustion,...
-
“Shadow” vs. “Phase 3D” method within endoscopic examinations of marine engines
PublicationA visual investigation of surfaces creating internal, working spaces of marine combustion engines by means of specialized view-finders so called endoscopes is at present almost a basic method of technical diag-nostics. The surface structure of constructional material is visible during investigations like through the magnifying glass (usually with a precisely determined magnification), which makes possible a detection, recognition...
-
Selection of drive engines for dredge pumps
PublicationThis paper presents the principles of selecting drive engines for dredge pumps, formulated by this author. In order to formulate them influence of drive engines on dredge pump characteristics and dredger effectiveness, have been analyzed. Also, an analysis of results of the author's operational investigations concerning energy consumption and parameters of excavated soil transport on board dredgers has been performed.
-
Balancing energy processes in turbine engines
PublicationThe article discusses the issue of balancing energy processes in turbine engines in operation in aeronautic and PDULQHSURSXOVLRQV\VWHPVZLWKWKHDLPWRDQDO\VHDQGHYDOXDWH EDVLFRSHUDWLQJSDUDPHWHUV7KH¿UVWSDUWSUHVHQWV the problem of enormous amounts of energy needed for driving fans and compressors of the largest contemporary turbofan engines commonly used in long-distance aviation. The amounts of the transmitted power and the effect RIÀRZSDUDPHWHUVDQGFRQVWUXFWLRQDOSURSHUWLHVRIWKHHQJLQHV RQWKHLUSHUIRUPDQFHDQGUHDOHI¿FLHQF\DUH evaluated....
-
Thermal efficiency investigations on the self-ignition test engine fed with marine low sulfur diesel fuels
PublicationWithin the article an issues of implementing the new kinds of marine diesel fuels into ships’ operation was described taking into ac-count restrictions on the permissible sulphur content introduced by the International Maritime Organization. This is a new situation for ship owners and fuel producers, which forces the necessity to carry out laboratory research tests on especially adapted engine stands. How to elaborate the method...
-
On the compression of multibeam sonar raw bathymetry data
PublicationMultibeam sonars are widely used in applications like high resolution bathymetry measurements or underwater object imaging. One of the significant problems in multibeam sensing of the marine environment is large amount of data which must be transmitted from the sonar processing unit to an operator station using a limited bit rate channel. For instance, such a situation would be in the case when the multibeam sonar was mounted on...