Search
Search results for: wkladka run flat
-
INNOVATIVE RUN FLAT SYSTEMS
PublicationOne of the most essential threats to the mobility of wheeled vehicles is their relatively high sensitivity to tire damage. Tires can be damaged as a result at vehicle-targeting fire, after running on a mine or an improvised charge. The purpose of the article is to analyze the current technical solutions in wheeled vehicle tires, allowing for the unobstructed use of the vehicle despite the damage of one or several tires (RUN FLAT...
-
Research on operational characteristics of tyres with run flat insert
PublicationThe paper describes results of research on heavy vehicle tyre with Run Flat VFI insert. The experiment has included the determination of heat generation, rolling resistanceand radial stifnessof two different tyre designes (textile and steel carcass). The results have been used for the purpose of ewalution of tyre operating characteristics. The study included research on non-inflated tyre properties. The purpose of the paper is...
-
Analysis of Rolling Resistance of Tires With Run Flat Insert
PublicationRun flat properties are required for tires intended for special applications like military or rescue vehicles. Run-Flat inserts make possible to drive a car or truck, with certain restrictions, also when inflation pressure is very low or non-existing (after tire damage). Rolling resistance of tires rolling the inserts increases considerably in relation to the rolling resistance of properly inflated tires. This paper presents results...
-
ANALYSIS OF ROLLING RESISTANCE OF TIRES WITH RUN FLAT INSERT APPLYING DRUM METHOD AND RADIAL CHARACTERISTIC
PublicationThis paper presents analysis of rolling resistance of tires with RUN FLAT insert applying drum method and radial characteristic. The conducted studies indicated changes in operational properties of wheel, occurring as a result of inflation pressure drop in the wheel. As regards radial elasticity, such changes result in significant drop of radial rigidity and increase of static deflection and increase of tire rolling resistance....
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - PARAFFIN OIL. Specim. set K09 - full run
Open Research DataFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: PARAFFIN OIL. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate...
-
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - PARAFFIN OIL. Specim. set K09A - full-run
Open Research DataVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: PARAFFIN OIL. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30,...
-
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - PARAFFIN OIL. Specim. set K09 - pre-run
Open Research DataVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: PARAFFIN OIL. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30,...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - PARAFFIN OIL. Specim. set K09 - pre-run (10s)
Open Research DataFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: PARAFFIN OIL. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate...
-
Laboratoryjne badania oporu toczenia i temperatury opon do pojazdów specjalnych
PublicationW pracy przedstawiono wyniki laboratoryjnych badań oporu toczenia i temperatury opon do pojazdów specjalnych. Współczynnik oporu toczenia tych opon jest silnie uzależniony od ciśnienia pompowania. Po utracie nadciśnienia w oponie, gdy następuje styk wewnętrznej powierzchni bieżnika z wkładką Run-Flat, opór toczenia wzrasta około 7-8 razy w stosunku do sytuacji gdy ciśnienie pompowania jest wyregulowane do jazdy po drogach utwardzonych...
-
PREDICTION OF SHIP MOTIONS IN IRREGULAR WAVES BASED ON RESPONSE AMPLITUDE OPERATORS EVALUATED EXPERIMENTALLY IN NOISE WAVES
PublicationThe most common methods for predicting ship roll motions in a specified sea state are direct measurements of motions in a representative irregular wave realisation (time domain) or calculations of motions from response amplitude operators (RAOs) in the frequency domain. The result of the first method is valid only for the tested sea state, whilst the second method is more flexible but less accurate. RAO-based predictions are calculated...
-
Influence of Flat Lapping Kinematics on Machinability of Ceramics
PublicationNew tools for flat grinding of ceramics are presented in the paper. Electroplated CBN tools (B64 and B107) were used in a modified single-disc lapping machine configuration. The results from experiments, such as the material removal rate and surface roughness parameters are presented and analyzed. Numerical simulations, based on the model for the shape error and tool wear estimation in machining with flat lapping kinematics, are...
-
Constant vs. Variable Efficiency of Electric Drive in Train Run Simulations
PublicationTrain run simulations, which focus on various power- and energy-oriented aspects, should reflect the losses in the electric powertrain. In general, the powertrain efficiency varies with respect to load and speed. Including this relation in simulation requires knowledge about detailed drivetrain parameters, which are often unavailable. This paper verifies the possibility to approximate the drivetrain efficiency in train run simulations...
-
Recent Advances in Loop Heat Pipes with Flat Evaporator
PublicationThe focus of this review is to present the current advances in Loop Heat Pipes (LHP) with flat evaporators, which address the current challenges to the wide implementation of the technology. A recent advance in LHP is the design of flat-shaped evaporators, which is better suited to the geometry of discretely mounted electronics components (microprocessors) and therefore negate the need for an additional transfer surface (saddle)...
-
Technological Problems in Lapping on Flat Surfaces of Ceramic Parts
PublicationThis paper will present the results of research on single-disc lapping of flat surfaces of small ceramic elements. Machining with the use of different tools such as metallic, two-metallic and abrasive-metallic will be analyzed. The basics and techniques of reinforcement of laps will be discussed. The results of the influence of parameters on the surface quality of ceramic conponents (sealing) for three treatments on lapping machines...
-
Performance of the flat plate solar collector operated with water-Al2O3 nanofluid
PublicationThis paper shows the experimental results of the performance a flat plate solar collector with water-Al2O3 nanofluid as a working fluid. The weight fractions of nanoparticles were 0.1%, 0.2% and 0.4%. The volume flow rate of nanofluid varied from 60 l/h to 170 l/h. The results show that application of nanofluids instead of pure water resulted in higher efficiency of the tested flat plate solar collector for given range of thermal...
-
Flow visualization and heat transfer investigations on the flat plate with streamwise pressure gradient
PublicationPaper presents experimental investigations results for film cooling on a flat plate. The main objective of the design is the streamwise pressure distribution on the flat plate as in the blade cascade. The transient and steady-state technique with liquid crystals for the surface temperature distribution with film cooling has been used in experiments in a low speed wind tunnel.
-
Performance of the flat plate solar collector operated with water-Al2O3 nanofluid
PublicationThe paper discusses the effect of application of water-Al2O3 nanofluid, as a working fluid, on the efficiency of a flat plate solar collector. The mass concentration of nanoparticles was 0.1%, 0.2% and 0.4%. The tests were conducted for two values of radiation of about 1050 W/m2 and 400 W/m2, and volume flow rates of 60 l/h, 120 l/h and 170 l/h. The efficiency was calculated according to recommendations of the Polish Standard....
-
Axsial run-out circular saws
PublicationW pracy przedstawiono podstawowe przyczyny i efekty bicia osiowego ostrzy pił w układzie przecinania na pilarkach tarczowych.
-
Optimisation of turbine shaft heating process under steam turbine run-up conditions
PublicationAn important operational task for thermal turbines during run-up and run-down is to keep the stresses in the structural elements at a right level. This applies not only to their instantaneous values, but also to the impact of them on the engine lifetime. The turbine shaft is a particularly important element. The distribution of stresses depends on geometric characteristics of the shaft and its specific locations. This means a groove manufactured...
-
Flow of liquid in flat gaps of the satellite motor working mechanism
PublicationThe article describes the methodology and results of investigations of the flow of oil and HFA-E emulsion in flat gaps of the working mechanism of a satellite motor. The flow of liquid in those gaps is turbulent and not fully developed. The article presents two methods of modelling this flow. Method I makes use of the Darcy-Weisbach formula, while Method II bases on the assumption that in the variable-length gaps the flow is turbulent...
-
Assessment of radial run-out of circular saw.
PublicationW pracy przedstawiono ocenę bicia promieniowego pił tarczowych na podstawie analizy zróżnicowania przekrojów warstw skrawanych przez poszczególne ostrza piły
-
Convex set of quantum states with positive partial transpose analysed by hit and run algorithm
PublicationThe convex set of quantum states of a composite K×K system with positive partial transpose is analysed. A version of the hit and run algorithm is used to generate a sequence of random points covering this set uniformly and an estimation for the convergence speed of the algorithm is derived. For K >3 or K=3 this algorithm works faster than sampling over the entire set of states and verifying whether the partial transpose is positive....
-
Simplified method of applying loads to flat slab floor structural model
PublicationThe article analyses the impact of the live load position on the surface of a reinforced concrete flat slab floor of 32.0 m × 28.8 m. Four variants of a live load position are investigated: located on the entire concrete slab, set in a chessboard pattern, applied by bands and imposed separately in each of the slab panels. Conclusions are drawn upon differences in bending moments, the time of calculation and the size of output files....
-
Vertical motions damping model test of a lifeboat lowered onto a flat sea surface
PublicationThe article presents the experiment’s results of the lifeboat model lowered with an initial speed and then released to fall onto a flat water surface. The purpose of the research is to determine the trajectory of the vertical boat motion and describe it with a mathematical model. This is closely related to determining the damping factor since the vertical motion is damped and the lifeboat gets balanced and stops moving after some...
-
Geometrical effects of axial run-out in circular saws
PublicationW pracy omówione zostały efekty geometryczne jakie wywoływane są przez błąd bicia osiowego pił tarczowych.
-
Geometrical accuracy of the objects in the axial run-out conditions
PublicationW pracy omówiono wpływ wartości bicia osiowego ostrzy pił tarczowych i parametrów obróbki na dokładność geometryczną powierzchni uzyskiwanych podczas procesu przecinania.
-
Commissioning of the CMS experiment and the cosmic run at four tesla
Publication -
Influence of the Shear Cap Size and Stiffness on the Distribution of Shear Forces in Flat Slabs
PublicationThe scope of this paper is to investigate analytically and numerically the influence of shear cap size and stiffness on the distribution of shear forces in flat slabs in a slab–column-connections-reinforced concrete structure. The effect of support (shear cap) stiffness on the calculation of the length of the shear control perimeter according to the available methods is presented. Based on the analysis, the authors indicate in...
-
Sinusoidal Alternating-Current Voltammetry and Metrological Properties of a Flat Voltammetric Electrode in the Time Domain
PublicationIn this paper there were analyzed metrological properties of a flat electrode used to mark ions with the method of sinusoidal alternating-current voltammetry in the situation where on its surface an electrochemical reversible reaction of oxidizing / reduction takes place. The result of the analysis conducted is that such a voltammetric electrode functions like a converter type I. Metrological properties of such an electrode in...
-
Corporate governance and propensity to share information: The long-run effect
Publication -
Analysis of radial run-out of circular saw's cutting blades
PublicationW pracy przedstawiono analizę bicia promieniowego ostrzy pił tarczowych w procesie przecinania drewna. Analizę przeprowadzono na podstawie zróżnicowania grubości warstw skrawanych przez poszczególne ostrza piły. Dla przykładowej piły, zaprezentowano wyniki obliczeń przebiegów grubości warstw skrawanych przez poszczególne ostrza i grubości całkowitej warstwy skrawanej dla całej piły.
-
Analysis of flat compensator lapping in an assembly process
PublicationPrzedstawiono sposób analizy docierania kompensatora płaskiego podczas montażu połączenia konstrukcyjnego. Wyznaczono czas główny obróbki i koszty operacji docierania jednotarczowego
-
Correlation between shape errors in flat grinding
PublicationW pracy przedstawiono wyniki badań eksperymentalnych i symulacyjnych związanych z wpływem błędów kształtu narzędzia na błędy ksztaltu przedmiotu szlifowanego w układzie docierarki jednotarczowej. Szlifowanie realizowane było z wykorzystaniem specjalnych narzędzi z możliwością regulacji przekroju promieniowego.
-
Research on the wear evenness of the tool in flat lapping
PublicationIn this paper, the dimensionless distribution of the material removal stock and the trajectories of abrasive grains cutting in single-sided lapping process are presented. They were numerically simulated based on the tribological model and kinematics equations. It can be observed that the trajectories geometry of single abrasive as well the velocities have a great influence on the final geometrical deviation. During machining, the...
-
Lapping of flat surfaces with two metallic tools.
PublicationPrzedstawiono opis docierania powierzchni płaskich docierakami aktywizowanymi w sposób swobodny i wymuszony oraz narzędziami dwumetalowymi i ściernometalowymi. Wyznaczono zużycie docieraków stalowo-żeliwnych oraz wydajność obróbki żeliwa sferoidalnego niestopowego i stali NC6.
-
Problems of flat surface lapping : chapter 16
PublicationPrzedstawiono problemy docierania powierzchni płaskich w układach jednotarczowych. Omówiono analityczne i numeryczne modele kinematyki docierarek konwencjonalnych i niestandardowych, obróbkę docierakami aktywizowanymi w sposób swobodny i wymuszony, jednolitymi i dwumetalowymi. Zaprezentowano wyniki obróbki narzędziami ścierno-metalowymi elementów ceramicznych.
-
Experimental and analytical analysis of punching shear in flat slabs supported on column topped with concrete head
PublicationAn experimental laboraatory test of the two series of slab-column elements topped with drop panels of varying sizes is described in this paper. The scope of the paper is to investigate the influence of the drop panel size and stiffness on the behaviour of the connection between the flat slab and the column topped by the concrete head. The impact of the head size and stiffness is analysed analytically and experimentally. The experimental...
-
Cut layer of a circular saw with radiaj run-out of cutting edges
PublicationW pracy przedstawiono analizę wpływu bicia promieniowego ostrzy piły tarczowej na zmianę nominalnego i całkowitego pola przekroju warstwy skrawanej.
-
CMS data processing workflows during an extended cosmic ray run
Publication -
Fast description of medical images using run length encoded regions.
PublicationZaprezentowano szybką, adaptacyjną metodę progowania oraz opisu obrazów medycznych w oparciu o ich reprezentację za pomocą kodów długości serii (RLC). Przedstawiono możliwości wyznaczania deskryptorów kształtu oraz analizy porównawczej regionów. Omówiono właściwości metody oraz przykładowe rezultaty.
-
Lapping flat surfaces with forced dosing of abrasive suspension
PublicationPrzedstawiono zbudowane stanowisko do badań wymuszonego dawkowania zawiesiny ściernej w procesie jednostronnego docierania powierzchni płaskich. Podano przyjęty program badań oraz sposób opracowania wyników realizowanych eksperymentów.
-
Lapping flat surfaces with forced dosing of abrasive suspension
PublicationPrzedstawiono zbudowane stanowisko badawcze umożliwiające wymuszone dozowanie zawiesiny ściernej w operacji docierania jednotarczowego powierzchni płaskich. Podano program badań własnych oraz sposób opracowania otrzymanych wyników realizowanych eksperymentów.
-
Computer simulation of induction hardening of moving flat charge
Publication -
Microgrinding of flat surfaces on single-disk lapping machine
PublicationW pracy przedstawiono wyniki badań mikroszlifowania z kinematyką docierania w układzie jednotarczowym z wykorzystaniem nowego narzędzia wykonanego z pastylek ściernych z ziarnem diamentowym (D3/2) i spoiwem żywicznym. Zakres pracy obejmował przeprowadzenie badań eksperymentalnych i modelowych związanych z analizą promienia krzywizny rys obróbkowych.
-
Determining the conditions for temperature measurements during flat lapping
PublicationPrzedstawiono pomiary temperatury układu wykonawczego docierarki jednotarczowej ABRALAP 380. Badano wpływ liczby stosowanych pierścieni prowadzących przy docieraniu elementów ceramicznych mikroziarnami węglika krzemu. Analizowano przyrost temperatury układu w czasie do trzech godzin. W badaniach zastosowano kamerę termowizyjną V-20II firmy VIGO System S.A.
-
Wear of Electroplated Tools Used for Flat Grinding of Ceramics
PublicationTwo methods for the abrasive properties evaluation, based on the image processing, are presented in the paper. Image processing analysis was developed to evaluate quickly the abrasive properties as the tool wears down. The coefficient based on the image brightness was calculated and additional analysis was based on the number of grains located on the active surface of the tool before and after machining. The active surfaces of...
-
Microgrinding of flat surfaces on single-disc lapping machine
PublicationW pracy przedstawiono możliwości zastosowania specjalnych narzędzi do mikroszlifowania na docierarce jednotarczowej. Jedno z zastosowanych narzędzi posiada warstwę ścierniwa diamentowego (D64) nałożoną metodą galwaniczną. Drugie przetestowane narzędzie zbudowane zostało z diamentowych pastylek ściernych (D3/2). Przedstawiono analizę kinematyczną i wyniki ubytku materiałowego oraz osiągnięte parametry chropowatości.
-
Microgrinding of flat surfaces on a single-disc lapping machine
PublicationW referacie przedstawiono wyniki badań eksperymentalnych mikroszlifowania z kinematyką docierania jednotarczowego. Przedstawiono propozycję narzędzia z wkładkami ściernymi z ziarnem diamentowym D3/2 i spoiwem żywicznym. Omówiono kinematykę docierania jednotarczowego i sposób oceny krzywizny rys obróbkowych.
-
Machining of the flat surfaces with abrasive-metallic lapping tools.
PublicationPrzedstawiono konstrukcje narzędzi ścierno-metalowych do obróbki powierzchni płaskich na docierarkach jednotarczowych. Przeprowadzono badania wydajności i jakości powierzchni elementów ceramicznych o małych gabarytach.
-
Advanced acoustic signal analysis used for wheel-flat detection
Publication