Search results for: FLUID FLOWMEASUREMENT
-
Edwards' syndrome, unspecified - Male, 1 - Tissue image [3070630010182101]
Open Research DataThis is the histopathological image of BRONCHUS AND LUNG tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Studies of the Interaction Dynamics in Albumin-Chondroitin Sulfate Systems by Recurrence Method
PublicationThe physicochemical basis of lubrication of articular cartilage is still not fully understood. However, the synergy between components of the synovial fluid can be a crucial factor that could explain this phenomenon. This work presents a nonlinear data analysis technique named the recurrence method, applied to the system involving two components of synovial fluid: albumin and chondroitin sulfate (CS) immersed in a water environment....
-
The Processing Procedure for the Interpretation of Microseismic Signal Acquired from a Surface Array During Hydraulic Fracturing in Pomerania Region in Poland
PublicationHydraulic fracturing is a procedure of injecting high pressure fluid into the wellbore in order to break shell rock and facilitate gas flow. It is a very costly procedure and, if not conducted properly, it may lead to environmental pollution. To avoid costs associated with pumping fluid outside the perspective (gas rich) zone and improve one’s knowledge about the reservoir rock, microseismic monitoring can be applied. The method...
-
The thermal effort during marine steam turbine flooding with water
PublicationThe work discussed an extreme case of cooling a steam turbine. The ship's steam turbine was used as an example. In marine transport units with low-speed engines dominate, however, there are also units with steam turbines. An example of analysed marine steam turbine is shown in Fig. 1. When considering the issue of cooling steam turbines, it is necessary to estimate the extreme conditions that may occur during operation of the turbine....
-
Deformable model of a butterfly in motion on the example of Attacus atlas
PublicationInsect wings can undergo significant chordwise (camber) as well as spanwise (twist) deformation during flapping flight but the effect of these deformations is not well understood. The shape and size of butterfly wings leads to particularly large wing deformations, making them an ideal test case for investigation of these effects. High-speed videogrammetry was used to capture the wing kinematics and deformations. The movements of...
-
Effect of Ion and Binding Site on the Conformation of Chosen Glycosaminoglycans at the Albumin Surface
PublicationAlbumin is one of the major components of synovial fluid. Due to its negative surface charge, it plays an essential role in many physiological processes, including the ability to form molecular complexes. In addition, glycosaminoglycans such as hyaluronic acid and chondroitin sulfate are crucial components of synovial fluid involved in the boundary lubrication regime. This study presents the influence of Na+, Mg2+ and Ca2+ ions...
-
A novel in vivo approach to assess strains of the human abdominal wall under known intraabdominal pressure
PublicationThe study concerns mechanical behaviour of a living human abdominal wall. A better mechanical understanding of a human abdominal wall and recognition of its material properties is required to find mechanically compatible surgical meshes to significantly improve the treatment of ventral hernias. A non-invasive methodology, based on in vivo optical measurements is proposed to determine strains of abdominal wall corresponding to...
-
Hysteresis curves for some periodic and aperiodic perturbations in gases
PublicationEvolution of sound in a medium whose properties irreversibly vary in the course of wave propagation, is studied. For example, a gas that is a particular case of a Newtonian fluid is considered. Hysteresis curves, pictorial representations of irreversible attenuation of the sound energy, in the plane of thermodynamic states are plotted. The irreversible losses in internal energy are proportional to the total attenuation and depend...
-
Thermal Self-Action Effects of Acoustic Beam in a Gas with Reversible or Irreversible Chemical Reaction
PublicationThermal self-action of acoustic beam in a gas where an exothermic chemical reaction takes place, is studied. This kind of thermal self-action differs from that in a newtonian fluid. In dependence on the type of a chemical reaction, reversible or not, heating or cooling of a medium occurs. A beam in the case of the irreversible reaction may be unusually self-focusing. The self-action effects relating to wave beams containing shock...
-
Highly sensitive large strain cellulose/multiwalled carbon nanotubes (MWCNTs)/thermoplastic polyurethane (TPU) nanocomposite foams: From design to performance evaluation
PublicationAerogel-based polymer composite foams are promising for large strain piezoresistive sensors, but their aerogel skeleton is partially destroyed during the foaming process, limiting their sensitivity. Herein, the thermoplastic polyurethane was synthesized on the aerogel skeleton to obtain cellulose/multiwalled carbon nanotubes (MWCNTs)/thermoplastic polyurethane (TPU) nanocomposite materials foamed with the aid of supercritical carbon...
-
Theoretical investigations into flows in rotor blade shroud clearance
PublicationPrzedstawiono wyniki obliczeń programem Fluent przepływów w uszczelnieniu nadbandażowym stopnia turbinowego przy różnym mimośrodowym położeniu osi wirnika względem osi korpusu. Wyznaczone numerycznie rozkłady ciśnienia w uszczelnieniu i generowane tam siły aerodynamiczne porównano z rezultatem badań przeprowadzonych na powietrznej turbinie modelowej.
-
Analysis of transient heat transfer operation in tube wall.Selected papers from the International Conference on Turbines of Large Output devoted to 100th Anniversary of Prof. Robert Szewalski Birthday.
PublicationW pracy przedstawiono zachowanie się wymiennika ciepła stosowanego w układzie regeneracji turbin parowych w niestacjonarnych warunkach pracy.
-
On Application of Selected Methods of Artificial Intelligence in Expert Systems for Thermal and Flow Diagnostics
PublicationPrzedyskutowano problem wspomagania przez systemy ekspertowe decyzji eksploatacyjnych służb nadzoru obiegów turbin parowych. Uwagę skupiono na realizacji jednego z zadań tych systemów, polegającemu na określenie rozmiaru eksploatacyjnej degradacji parametrów geometrycznych układów łopatkowych turbin. Dyskusję przeprowadzono na przykładzie jednego z komponentów metod sztucznej inteligencji: wybranego typu sztucznej sieci neuronowej...
-
An impact of ambient parameters change on steam and gas turboset control. The International Conference on ''Turbines of Large Output'' devoted to 100th Anniversary of prof. Robert Szewalski Birthday.
PublicationPorównano wpływ zmian parametrów otoczenia (ciśnienia i temperatury) na charakterystyki turbiny parowej i gazowej. Na tej podstawie zbadano wpływ tych parametrów na charakterystyki układu kombinowanego parowo-gazowego. Przedstawiono, w związku z tym, koncepcję kompensatora wpływu zmian parametrów otoczenia na charakterystyki układu kombinowanego parowo-gazowego.
-
Volute scroll as an alternative to guide vanes at inlet to turbine.
PublicationW pracy przedstawiono alternatywny sposób zasilania turbin parowych poprzez zastosowanie podwójnej spirali zasilającej. Przedstawiono model jednowymiarowy obliczania przepływu przez spirale oraz zamieszczono wyniki obliczeń typu 3D. Pokazano jak zależy parametr nierównomierności rozkładu prędkości na wylocie od sposobu kształtowania przekroju spiral.
-
Estimation of the steam condensation flow via CFD methods
PublicationThe results of numerical simulations to predict the performance of different steam models have been presented. All of the considered models of steam condensation have been validated on the base of benchmark experiment employing expansion in nozzle and next on the low pressure part of the steam turbine stage. For numerical analysis three models have been finally used – the ideal steam model without condensation, an equilibrium steam...
-
Influence of gas parameters alteration on the form of gas-flow-impact appearing in long transportation pipelines
PublicationPrzy szybkich zamknięciach przepływu w długich liniach transportowych gazu, obserwuje się znaczne przesterowania ciśnienia, towarzyszące zjawiskom udarowym, wywołane zarówno falą uderzeniową jak i odbitą. Głównym czynnikiem wpływającym na postać fali uderzeniowej i jej amplitudy, jest szybkość zamykania zaworu odcinającego określona stałą czasową serwomotoru sterującego zaworem. Ponieważ obserwuje się zmiany właściwości chemicznych...
-
Investigation of R 22 and R 134a flow boiling in enhanced tubes
PublicationPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła i spadków ciśnienia podczas wrzenia w przepływie R22 oraz R134a. Do badań użyto dwie rurki o rozwiniętej wewnętrznej powierzchni, tj. rurkę śrubowo-formowaną i rurkę niskożebrowaną oraz dwie rurki gładkie, jako rurki referencyjne. Eksperymenty przeprowadzono przy temperaturze nasycenia ok. zero stopni Celsjusza i końcowym stopniu suchości ok. 0.7. Wyniki badań eksperymentalnych...
-
Experimental investigations of hydraulic jump created by a two-phase impin-ging jet on a solid surface
PublicationPrzedstawiono rezultaty badań eksperymentalnych powstawania uskoku hydraulicznego tworzonego przez dwufazową strugę uderzającą.
-
Motion of a sphere in vicinity of the wall
PublicationArtykuł skupiony jest na badanich odchylenia toru cząstki w sąsiedztwie ścianki. Cząstka modelowana jest nieodkształcalną kulą zawieszoną na strunie. Systematyczne badania z wykorzystaniem kul o trzech średnicach wykonano na specjalnie zbudowanym stanowisku eksperymentalnym. Zaproponowano autorską matematyczną korelację opisującą oddziaływanie ścianki na ruch cząstki - korelacja określa to oddziaływanie w funkcji początkowej odległości...
-
INFLUENCE OF SURFACE CURVATURE ON SESSILE DROPLET CONTACT ANGLE OF NANOFLUIDS
PublicationThis paper deals with change in contact angle of droplets of three nanofluids, i.e. water-Al2O3, water-TiO2 and water-Cu. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight. Although dispersants were not used to stabilize the suspension, the solutions tested exhibited satisfactory stability. Ultrasonic vibration was used in order to stabilise the dispersion of the nanoparticles. Experimental measurements...
-
On the internal efficiency of a turbine stage: classical and CFD definitions
PublicationAlmost entire fleet of steam turbines in Poland was designed between 1950 – 1980 with the use of the so-called zero dimensional (0D) calculation tools. For several years, design and modernization of the turbines occur in assistance with the state of the art methods that describe working fluid flow field based on 3D models and CFD codes. This cooperation between 0D and 3D codes requires exchange of overall, integral information...
-
Clean gas technologies - towards zero-emission repowering of Pomerania.
PublicationThe main aim this work is to show the different thermodynamic cycles which improve efficiency and/or decrease emission like: Cheng cycle, Szewalski cycle, LOTHECO cycle, hybrid pSOFC/GT cycle, inverse Brayton cycle, low-emission cycle and zero-emission cycle. For that purpose, cycles and results of analysis are first studied and, secondly, new concept is presented. The role of coupled analysis 0D and 3D in cycle’s devices is also...
-
Design and distribution of air nozzles in the biomass boiler assembly
PublicationDue to energy crisis as well as increasing pollution of the environment, renewable energy sources usage increases all over the world. These facts encouraged authors to start research over developing a uniform biomass boiler calculation model. This paper presents a design of biomass boiler assembly created for ORC (Organic Rankine Cycle) unit since these systems could achieve strong position in energy industry....
-
Enhancement of the Brayton cycle efficiency by water or steam utilization
PublicationIn the paper, thermodynamic analysis of two modifications of a Brayton cycle into enhancement cycles with water/steam injection are discussed. The first one deals with a STIG modified system with both interstage compressed air cooling and air heating (heat regeneration) before combustion chamber. The second one, mainly devoted to higher steam/air ratio, is connected with separate steam production in a HRSG. The analysis has been...
-
HIERARCHICAL CYCLES IN MODERN POWER SYSTEMS – EXERGY ANALYSIS UNDER PART LOADS
PublicationThe aim of the paper is to investigate thermodynamic efficiency of advanced hierarchic power cyclesunder partial loads by using of exergy analyze. Advanced hierarchical power systems arecomposed of few energy conversion cycles, most common are steam and gas cycles in various configurations, but they may contain fuel cells, ORC, lithium bromide absorption chillers and others. Moreover hierarchical cycles can be powered by several...
-
An advanced thermal-FSI approach of an evaporation of air heat pump
PublicationThe paper presents selected problems of numerical modeling of an advanced thermal-FSI approach of evaporator of air heat pomp. The example of a fin-tube evaporator has been studied, focusing on obtaining of heat exchanger characteristics applying two-phase flow model for the in-tube refrigerant flow. Special attention is given to heat transfer between separated medium for different air velocity and changed refrigerant mass flow...
-
ENHANCED EVAPORATION OF THE DROPLETS OF CONDENSATE IN THE ASYMMETRICAL SHOCK WAVE ZONE
PublicationIn the low-pressure part of steam turbine, the state path usually crosses the saturation line in penultimate stages [4,5]. The formation and evolution of these droplets lower the performance of the wet stages of the turbines, and their effects on the efficiency are collectively known as wetness losses [4]. Nowadays, due to work of steam turbines at partial load, process of homogeneous and heterogeneous condensation still is current....
-
STUDY ON THE EFFECTIVENESS OF THE TURBINE CONDENSER AIR EXTRACTION SYSTEM USING HYDRO EJECTORS
PublicationThe aim of the paper is to investigate the effectiveness of the 18K380 steam turbine condenser air extraction system using hydro ejectors. Motivation for the analysis is a need of improvement of the energy conversion ratio of the power plant. To achieve this goal it is necessary to establish efficiency of each subsystem of the energy cycle. The air extraction system is not a highly power consuming system but it has great impact...
-
A role of the heat and work uncompensatedtransformations in the balance of entropy and theturbomachinery efficiency
PublicationIn the paper we have presented a procedure of estimating a role of the uncompensated transformation of heat and work in ow of viscous and heat conducting uid. The procedure was introduced by Professor Romuald Puzyrewski and is essential in local, in time and space, balance of entropy. Furthermore this unique approach leads to redenition the eciency of uid-ow machinery in three-dimensional modeling using CFD (Computational Fluid...
-
DEVELOPMENT OF A COUPLED NUMERICAL AND EXPERIMENTAL APPROACH TO HYDRODYNAMIC NOISE ESTIMATION
PublicationThe hydroacoustic signature of ships' propellers can be estimated experimentally through measurements of cavitation-induced pressure fluctuations and the corresponding noise distributions at model scale. These measurements need to be performed in a cavitation tunnel under the propellers operating conditions and are quite sensitive and challenging to perform with sufficient accuracy. In comparison, the numerical approach can be...
-
Design criterion for hydrodynamic vortex separators
PublicationTechnical objects designing involves determination of geometrical parameters that characterize a given object. When the device is described by the differential equations, an inverse problem brings difficulties, as geometrical values sought condition the solution to the problem. Vortex separators can be designed by the "criterion method'. Firstly, a critical particle is distinguished such that bigger particles are removed from...
-
How much a geometrical model of a honeycomb seal can be simpli ed in the CFD calculation
PublicationThis paper presents the inuence of geometry simplication on the results obtained in the computational fluid dynamics simulation. The subject of simulation was part of the honeycomb seal located at the inlet to high pressure part of a steam turbine. There were three different geometrical models assumed in the calculations. First one was two-dimensional case and two others were three dimensional, one with the radius of curvature...
-
Experimental and theoretical study of surface cooling using a single microjet
PublicationPrzedstawiono wyniki badań eksperymentalnych intensyfikacji wymiany ciepła przy pomocy pojedynczych strug wody i powietrza.Uzyskana na podstawie wyników korelacja, opisująca współczynnik przejmowania ciepła, posłużyła do weryfikacji modelu opracowanego wcześniej przez Mikielewicza (2007).
-
Kinetic analysis of the stage for a high speed steam turbine
PublicationThis article analyzes possibilites of resonances within a control stage for a high speed steam turbine. This stage hase been based on assembling of a single blade to a rotating disk and increasing of rigidity of the system by using of a bandage. In the analysis will be nd a possiblity of resonance frequency, and mistuning by showing safety working ranges. The calculations have bean used the3D modal and harmonic analysis by the...
-
NEW TRENDS IN DEVELOPMENT OF ORC'S FOR MICROPOWER GENERATION
PublicationIn the paper, new trends in development of micropower generation of heat and electricity are presented. New type of CHP for domestic usage is developed in the Institute of Fluid-Flow Machinery PAS and methods of its design are presented. The most promising trends in equipment of ORC cycle for this purpose were discussed. Main attention was focused on micro-heat exchangers design based on micro-channels and micro-jets. In our opinion...
-
THERMODYNAMIC ANALYSIS OF A GENERATION IV SCWR NUCLEAR POWER PLANT CYCLE
PublicationThis article presents a flow and thermodynamic analysis of a Generation IV nuclear cycle. An SCWR (Supercritical water reactor) is a high temperature and high pressure reactor that uses water at a temperature above its thermodynamic critical point as the working fluid. The cycle used for the calculations consists of one interstage superheater and 7 regenerative heat exchangers. Division pressure was optimized in view of the cycle efficiency,...
-
VOF-DEM-FEM combined model of the reef breakwater collapse
PublicationZespolony model numeryczny (metoda modelowania przepływu ze swobodną powierzchnią rozdziału faz ciekłej i gazowej w siatce nieruchomej (ang. Volume of Fluid - VOF, metoda elementów dyskretnych (ang. Distinct Element Method, metoda elementów skończonych (MES)) został wykorzystany do zbadania odkształceń falochronu narzutowego i jego piaszczystego podłoża w wyniku oddziaływania falowania powierzchniowego. Wyniki analizy numerycznej...
-
Characteristic and specificity of protease activity of thermophilic bacteria Meiothermus ruber
PublicationThe primary purpose of research was to establish the possibility of using thermophilic bacteria Meiothermus ruber as a source of proteolytic enzymes. The main reason of searching new proteases is their commercial value especially in production of detergents, food, pharmaceuticals, leather, diagnostics or waste management. The development of this type processes will be possible by utilization of enzymes which have unique characteristics...
-
Experimental investigations on condensation in flow of HFE-7100 in small diameter channels
PublicationIn the paper the authors present investigations of flow condensation with the use of the HFE-7100 as a working fluid. The original and new approach to removing the heat from the channel was applied. The research was carried out using a wide-range real time observations, e.g. using infrared camera and stroboscope microphotography. This paper presents the details of experiment as well as the influence of heat and flow parameters...
-
Thermal Energy Development in Magnetohydrodynamic Flow Utilizing Titanium Dioxide, Copper Oxide and Aluminum Oxide Nanoparticles: Thermal Dispersion and Heat Generating Formularization
PublicationThe main aim of this article heat transfer in thermal engineering deals with the production, use, transformation, and transfer of thermal energy. Engineering and industrial fields including food packaging, the production of food additives, electronic cooling, microturbines, etc. heavily rely on heat transmission. Due to its intriguing potential in industries like the production of polymers, paper, crystal glass, etc., scientists...
-
Vident-real: an intra-oral video dataset for multi-task learning
Open Research DataWe introduce Vident-real, a large dataset of 100 video sequences of intra-oral scenes from real conservative dental treatments performed at the Medical University of Gdańsk, Poland. The dataset can be used for multi-task learning methods including:
-
Investigation of the thermal effects in water-lubricated journal bearings with axial grooves
PublicationWater-lubricated hydrodynamic journal bearings are frequently applied as stern tube bearings due to their advantages over other bearing types. They are environmentally friendly, can operate without sealings and in conditions of low friction losses. The most popular are bearings with open axial grooves, which require, for proper operation, forced axial flow of the lubricating water. Correctly designed and operated stern tube bearings...
-
Teratoma, malignant, NOS - Female, 39 - Tissue image [3300730069399491]
Open Research DataThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Teratoma, malignant, NOS - Female, 39 - Tissue image [3300730069394661]
Open Research DataThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Teratoma, malignant, NOS - Female, 39 - Tissue image [3300730069393031]
Open Research DataThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Teratoma, malignant, NOS - Female, 39 - Tissue image [3300730069395471]
Open Research DataThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Teratoma, malignant, NOS - Female, 39 - Tissue image [330073006939961]
Open Research DataThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Teratoma, malignant, NOS - Female, 39 - Tissue image [3300730069393181]
Open Research DataThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Teratoma, malignant, NOS - Female, 39 - Tissue image [3300730069392881]
Open Research DataThis is the histopathological image of OVARY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.